This patch adds the 57780 PHY ID to the broadcom module.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch, 51e2a3846e, made
genphy_config_aneg() not restart aneg by calling genphy_restart_aneg() if
the advertisement hadn't changed.
But, genphy_restart_aneg() doesn't just restart aneg, it may also *enable*
aneg or un-isolate the PHY from the MII (those functions are controlled by
the same register). The code to avoid calling genphy_restart_aneg() didn't
consider this.
So, modify genphy_config_aneg() to also check if the PHY needs to have aneg
enabled or be un-isolated before deciding not to restart aneg.
This caused a problem with certain Davicom PHYs, as that driver isolates
the PHY (why?) before calling genphy_config_aneg() and expects the PHY to
be un-isolated by that function.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make mdio-gpio work with non OpenFirmware gpio implementation.
Aditional changes to mdio-gpio:
- use gpio_request() and gpio_free()
- place irq[] array in struct mdio_gpio_info
- add module description, author and license
- add note about compiling this driver as module
- rename mdc and mdio function (were ugly names)
- change MII to MDIO in bus name
- add __init __exit to module (un)loading functions
- probe fails if no phys added to the bus
- kzalloc bitbang with sizeof(*bitbang)
Changes since v3:
- keep bus naming "%x" to be compatible with existing drivers.
Changes since v2:
- more #ifdefs reduction
- platform driver will be registered on OF platforms also
- unified platform and OF bus_id to phy%i
Changes since v1:
- removed NO_IRQ
- reduced #idefs
Laurent, please test this driver under OF.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46abc02175 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the expansion register access routines a little more
formal. They will be used by the following bcm50610 support patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds flow control support to Broadcom phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core now has this helper function, so might as well use it
instead of forcing the phy code to roll their own version.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following build error caused by
commit ed94493fb3
(mv643xx_eth: convert to phylib):
<-- snip -->
...
Building modules, stage 2.
MODPOST 1280 modules
ERROR: "genphy_restart_aneg" [drivers/net/mv643xx_eth.ko] undefined!
...
make[2]: *** [__modpost] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning, missing description:
Warning(lin2627-g3-kdocfixes//drivers/net/phy/mdio_bus.c:63): No description found for parameter 'd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
This way the phy layer will respond to a change in phy state immediately,
instead of up to one second later when the state machine timer runs.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's aneg is configured and restarted whenever the link is brought up,
e.g. when DHCP is started after the kernel has booted. This can take the
link down for several seconds while auto-negotiation is redone.
If the advertised features haven't changed, then it shouldn't be necessary
to bring down the link and start auto-negotiation over again.
genphy_config_advert() is enhanced to return 0 when the advertised features
haven't been changed and >0 when they have been.
genphy_config_aneg() then uses this information to not call
genphy_restart_aneg() if there has been no change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the SIOCGMIIPHY case fall through properly (it is supposed
to not only return the ID of the default PHY but also to read from
that PHY), and make phy_mii_ioctl() return the same error code as
generic_mii_ioctl() in case of an unsupported operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the bus scanning code in mdiobus_register() off
into a separate function, and makes this function available for
calling from external code. This allows incrementally scanning an
mii bus, e.g. as information about which addresses are 'safe' to
scan becomes available.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
{alloc,free}_mdio_bitbang() are not exported while they are used in
mdio-ofgpio driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds an MDIO bitbang driver that uses the GPIO library and its
OF bindings to access the bus I/Os.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit cac1f3c8 factored out the code for get_phy_id so that it
could be reused in multiple places. Turns out that some of the
users can be modular, so we need to export this symbol as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Broadcom PHYs supported missing from the description.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Configure the BCM5482S secondary SerDes for 1000Base-X mode when the
appropriate dev_flags are passed in to phy_connect(). This is
needed when the PHY is used for fiber and backplane connections.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PHYLIB was first marked as BROKEN on S390, then the enclosing menu marked
as non-S390, then the two dependencies merged with the conversion to
menuconfig. Reduce to non-S390.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Declared some things static, declared some things in the header.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for two additional SMSC PHY models with identical interrupt
source and mask registers to the LAN83C185
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several models of SMSC PHY have the same interrupt status and mask
registers as the LAN83C185, so these functions can service multiple
different PHY drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix kernel-doc warning:
Warning(linux-2.6.25-git11//drivers/net/phy/phy_device.c:275): No
description found for parameter 'bus_id'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sometimes the specific interaction between the platform and the PHY
requires special handling. For instance, to change where the PHY's
clock input is, or to add a delay to account for latency issues in the
data path. We add a mechanism for registering a callback with the PHY
Lib to be called on matching PHYs when they are brought up, or reset.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The BCM5464 can be used with the current broadcom PHY driver
by just adding the appropriate chip ID and using the existing
support within.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Having the id field be an int was making more complex bus topologies
excessively difficult. For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The other if blocks don't redeclare temp, remove the redeclaration in
the final if() block.
drivers/net/phy/marvell.c:214:7: warning: symbol 'temp' shadows an earlier one
drivers/net/phy/marvell.c:160:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for BCM5481 PHY. Unfortunately it's hard to
get specifications for this PHY, so its special register 0x18 isn't
annotated properly (but we know it's used to set up the delays).
I've kept the magic numbers, so we'll not forget to fix it at the
first opportunity, and will name that register and its bits correctly.
p.s. also fixed the line with broken indention, introduced by
commit 03157ac31e
PHYLIB: Add BCM5482 PHY support
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Marvell PHY m88e1111 (not sure about other models, but think they too)
works in two modes: fiber and copper. In Marvell PHY driver (that we
have in current community kernels) code supported only copper mode,
and this is not configurable, bits for copper mode are simply written
in registers during PHY initialization.
This patch adds support for both modes.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following build error introduced by commit
a79d8e93d3 and reported by Olaf Hering:
<-- snip -->
...
LD .tmp_vmlinux1
arch/powerpc/sysdev/built-in.o: In function `of_add_fixed_phys':
fsl_soc.c:(.init.text+0xd34): undefined reference to `fixed_phy_add'
make: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Matt Carlson