This driver seeks to force the Bluetooth device on for the duration of
5 seconds when the Bluetooth device has woken the host and after a
complete packet has been received. It does that by calling:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
The same can be achieved more succinctly with:
pm_request_resume();
That's because after runtime resuming the device, rpm_resume() invokes
pm_runtime_mark_last_busy() followed by rpm_idle(), which will cause
the device to be suspended after expiration of the autosuspend_delay.
No functional change intended.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Loading hci_bcm with CONFIG_GPIOLIB=n results in the following splat
when calling gpiod_to_irq() from bcm_get_resources():
WARNING: CPU: 0 PID: 1006 at ./include/linux/gpio/consumer.h:450 bcm_get_resources+0x50/0x80
CPU: 0 PID: 1006 Comm: kworker/u8:4 Tainted: G A 4.15.0-rc4custom+ #4
Hardware name: Apple Inc. MacBook8,1/Mac-BE0E8AC46FE800CC, BIOS MB81.88Z.0168.B00.1708080033 08/08/2017
Call Trace:
bcm_serdev_probe+0x8b/0xc0
driver_probe_device+0x202/0x310
__driver_attach+0x85/0x90
? driver_probe_device+0x310/0x310
bus_for_each_dev+0x57/0x80
async_run_entry_fn+0x2c/0xd0
process_one_work+0x1d2/0x3d0
worker_thread+0x26/0x3c0
? process_one_work+0x3d0/0x3d0
kthread+0x10c/0x130
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x1f/0x30
We could call gpiod_to_irq() only if IS_ENABLED(CONFIG_GPIOLIB) but
without GPIOLIB, the driver's power saving features can't be used,
so selecting GPIOLIB seems more appropriate.
The same issue is present in hci_intel.c and hci_nokia.c, fix those up
as well.
Reported-by: Max Shavrick <mxms@me.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver may sleep in the interrupt handler.
The function call path is:
bluecard_interrupt (interrupt handler)
bluecard_write_wakeup
schedule_timeout --> may sleep
To fix it, schedule_timeout is replaced with mdelay.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds the "ti,cc2560" compatible string for a TI CC2560 chip.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds an optional nvmem consumer to get a BD address from an external
source. The BD address is then set in the Bluetooth chip after the
firmware has been loaded.
This has been tested working with a TI CC2560A chip (in a LEGO MINDSTORMS
EV3).
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for setting the public address on Texas Instruments
Bluetooth chips using a vendor-specific command.
This has been tested on a CC2560A chip. The TI wiki also indicates that
this command should work on TI WL17xx/WL18xx Bluetooth chips.
During review, there was some question as to the correctness of the byte
swapping since TI's documentation is not clear on this matter. This can
be tested with the btmgmt utility from bluez. The adapter must be powered
off to change the address. If the baswap() is omitted, address is reversed.
In case there is a issue in the future, here is the output of btmon during
the command `btmgmt public-addr 00:11:22:33:44:55`:
Bluetooth monitor ver 5.43
= Note: Linux version 4.15.0-rc2-08561-gcb132a1-dirty (armv5tejl) 0.707043
= Note: Bluetooth subsystem version 2.22 0.707091
= New Index: 00:17:E7:BD:1C:8E (Primary,UART,hci0) [hci0] 0.707106
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0002} 0.707124
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.707137
@ MGMT Open: btmon (privileged) version 1.14 {0x0003} 0.707540
@ MGMT Command: Set Public Address (0x0039) plen 6 {0x0002} [hci0] 11.167991
Address: 00:11:22:33:44:55 (CIMSYS Inc)
@ MGMT Event: Command Complete (0x0001) plen 7 {0x0002} [hci0] 11.175681
Set Public Address (0x0039) plen 4
Status: Success (0x00)
Missing options: 0x00000000
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0003} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0002} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0001} [hci0] 11.175757
= Open Index: 00:17:E7:BD:1C:8E [hci0] 11.176807
< HCI Command: Vendor (0x3f|0x0006) plen 6 [hci0] 11.176975
00 11 22 33 44 55 .."3DU
> HCI Event: Command Complete (0x0e) plen 4 [hci0] 11.188260
Vendor (0x3f|0x0006) ncmd 1
Status: Success (0x00)
...
< HCI Command: Read Local Version Info.. (0x04|0x0001) plen 0 [hci0] 11.189859
> HCI Event: Command Complete (0x0e) plen 12 [hci0] 11.190732
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 2.1 (0x04) - Revision 0 (0x0000)
LMP version: Bluetooth 2.1 (0x04) - Subversion 6431 (0x191f)
Manufacturer: Texas Instruments Inc. (13)
< HCI Command: Read BD ADDR (0x04|0x0009) plen 0 [hci0] 11.191027
> HCI Event: Command Complete (0x0e) plen 10 [hci0] 11.192101
Read BD ADDR (0x04|0x0009) ncmd 1
Status: Success (0x00)
Address: 00:11:22:33:44:55 (CIMSYS Inc)
...
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).
We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().
Also changed the comment to be more informative while we are touching this
code.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The bt_* printk macros include a \n already, so we don't need extra ones
here.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:
1) A non functioning BT HCI getting registered
2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.
This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Asus T100HA laptop uses an ACPI HID of BCM2E72 for the bluetooth
part of the SDIO bcm43340 wifi/bt combo chip.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of hci send frame failure, skb is still owned
by the caller (hci_core) and then should not be freed.
This fixes crash on dragonboard-410c when sending SCO
packet. skb is freed by both btqcomsmd and hci_core.
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
John Stultz reports a boot time crash with the HiKey board (which uses
hci_serdev) occurring in hci_uart_tx_wakeup(). That function is
contained in hci_ldisc.c, but also called from the newer hci_serdev.c.
It acquires the proto_lock in struct hci_uart and it turns out that we
forgot to init the lock in the serdev code path, thus causing the crash.
John bisected the crash to commit 67d2f8781b ("Bluetooth: hci_ldisc:
Allow sleeping while proto locks are held"), but the issue was present
before and the commit merely exposed it. (Perhaps by luck, the crash
did not occur with rwlocks.)
Init the proto_lock in the serdev code path to avoid the oops.
Stack trace for posterity:
Unable to handle kernel read from unreadable memory at 406f127000
[000000406f127000] user address but active_mm is swapper
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Hardware name: HiKey Development Board (DT)
Call trace:
hci_uart_tx_wakeup+0x38/0x148
hci_uart_send_frame+0x28/0x38
hci_send_frame+0x64/0xc0
hci_cmd_work+0x98/0x110
process_one_work+0x134/0x330
worker_thread+0x130/0x468
kthread+0xf8/0x128
ret_from_fork+0x10/0x18
Link: https://lkml.org/lkml/2017/11/15/908
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Cc: Ronald Tschalär <ronald@innovation.ch>
Cc: Rob Herring <rob.herring@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix: drivers/bluetooth/Kconfig:35:warning: multi-line strings not
supported warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On many laptops the btusb device is the only USB device not having USB
autosuspend enabled, this causes not only the HCI but also the USB
controller to stay awake, together using aprox. 0.4W of power.
Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for
Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%).
The btusb driver already contains code to allow enabling USB autosuspend,
but currently leaves it up to the user / userspace to enable it. This
means that for most people it will not be enabled, leading to an
unnecessarily high power consumption.
Since enabling it is not entirely without risk of regressions, this
commit adds a Kconfig option so that Linux distributions can choose to
enable it by default. This commit also adds a module option so that when
distros receive bugs they can easily ask the user to disable it again
for easy debugging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Assuming that the original code idea was to enable in-band sleeping
only if the setup_rome method returns succes and run in 'standard'
mode otherwise, we should not return setup_rome return value which
makes qca_setup fail if no rampatch/nvm file found.
This fixes BT issue on the dragonboard-820C p4 which includes the
following QCA controller:
hci0: Product:0x00000008
hci0: Patch :0x00000111
hci0: ROM :0x00000302
hci0: SOC :0x00000044
Since there is no rampatch for this controller revision, just make
it work as is.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following race condition still existed:
P1 P2
cancel_work_sync()
hci_uart_tx_wakeup()
hci_uart_write_work()
hci_uart_dequeue()
clear_bit(HCI_UART_PROTO_READY)
hci_unregister_dev(hdev)
hci_free_dev(hdev)
hu->proto->close(hu)
kfree(hu)
access to hdev and hu
Cancelling the work after clearing the HCI_UART_PROTO_READY bit avoids
this as any hci_uart_tx_wakeup() issued after the flag is cleared will
detect that and not schedule further work.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
But for the SKU's 9x60, there a 3 variants of FW, which cannot be
differentiated just with hw_variant and devision_revision_id.
So to pick the appropriate FW file for 9x60 SKU's, it will be
differentiated using hw_variant, hw_revision and fw_revision rather
than hw_variant and device_revision_id only.
Format will be like this:
ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi and .ddc
Signed-off-by: Jaya P G <jaya.p.g@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Introduce ath_vendor_cmd function which can be used to
configure 'tags' and patch the firmware.
ATH vendor command has the following format:
| OPCODE (u8) | INDEX (LE16) | DLEN (U8) | DATA (U8 * DLEN) |
BD address configuration tag is at index 0x0001.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit dec2c92880 ("Bluetooth: hci_ldisc:
Use rwlocking to avoid closing proto races") introduced locks in
hci_ldisc that are held while calling the proto functions. These locks
are rwlock's, and hence do not allow sleeping while they are held.
However, the proto functions that hci_bcm registers use mutexes and
hence need to be able to sleep.
In more detail: hci_uart_tty_receive() and hci_uart_dequeue() both
acquire the rwlock, after which they call proto->recv() and
proto->dequeue(), respectively. In the case of hci_bcm these point to
bcm_recv() and bcm_dequeue(). The latter both acquire the
bcm_device_lock, which is a mutex, so doing so results in a call to
might_sleep(). But since we're holding a rwlock in hci_ldisc, that
results in the following BUG (this for the dequeue case - a similar
one for the receive case is omitted for brevity):
BUG: sleeping function called from invalid context at kernel/locking/mutex.c
in_atomic(): 1, irqs_disabled(): 0, pid: 7303, name: kworker/7:3
INFO: lockdep is turned off.
CPU: 7 PID: 7303 Comm: kworker/7:3 Tainted: G W OE 4.13.2+ #17
Hardware name: Apple Inc. MacBookPro13,3/Mac-A5C67F76ED83108C, BIOS MBP133.8
Workqueue: events hci_uart_write_work [hci_uart]
Call Trace:
dump_stack+0x8e/0xd6
___might_sleep+0x164/0x250
__might_sleep+0x4a/0x80
__mutex_lock+0x59/0xa00
? lock_acquire+0xa3/0x1f0
? lock_acquire+0xa3/0x1f0
? hci_uart_write_work+0xd3/0x160 [hci_uart]
mutex_lock_nested+0x1b/0x20
? mutex_lock_nested+0x1b/0x20
bcm_dequeue+0x21/0xc0 [hci_uart]
hci_uart_write_work+0xe6/0x160 [hci_uart]
process_one_work+0x253/0x6a0
worker_thread+0x4d/0x3b0
kthread+0x133/0x150
We can't replace the mutex in hci_bcm, because there are other calls
there that might sleep. Therefore this replaces the rwlock's in
hci_ldisc with rw_semaphore's (which allow sleeping). This is a safer
approach anyway as it reduces the restrictions on the proto callbacks.
Also, because acquiring write-lock is very rare compared to acquiring
the read-lock, the percpu variant of rw_semaphore is used.
Lastly, because hci_uart_tx_wakeup() may be called from an IRQ context,
we can't block (sleep) while trying acquire the read lock there, so we
use the trylock variant.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
In this particular case, notice that I replaced the
"deliberate fall-through..." comment with a "fall through"
comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 9834e586fa ("Bluetooth: btusb: Add workaround for Broadcom devices
without product id") was added to deal with the BT part of the BCM4356A2
on GPD pocket laptops having an usb vid:pid of 0000:0000.
After another commit to add support for the BCM UART connected BT ACPI-id
BCM2E7E used on the GPD win, it turns out that the BT on the GPD pocket is
connected via both USB and UART. Adding support for the BCM2E7E ACPI-id
causes it to switch to UART mode.
The Windows shipped with the device is using it in UART mode and the
presence of the BCM2E7E ACPI-id combined with the all 0 USB vid:pid
indicates that the BT part was never meant to be used in USB mode.
With the recent patches to use serdev device enumeration / instantiation
for UART attached ACPI enumerated BT devices, everything work OOTB in UART
mode and the workaround for the all 0 USB vid:pid is no longer needed.
This reverts commit 9834e586fa ("Bluetooth: btusb: Add workaround for
Broadcom devices without product id").
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested on a GPD win with a BCM4356 PCI-E wifi/bt combo card.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the device ID for the bluetooth chip used in the
Broadcom BCM4356 PCI-E WiFi / UART BT chip.
Successfully tested using Firmware version 0273
The upper nibble of the rev field is 2 on this device, so this commit
also adds handling of 2 to the switch-case done on the upper nibble.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is no longer possible to build BT_HCIUART into the kernel
when SERIAL_DEV_BUS is a loadable module, even if none of the
SERIAL_DEV_BUS based implementations are selected:
drivers/bluetooth/hci_ldisc.o: In function `hci_uart_set_flow_control':
hci_ldisc.c:(.text+0xb40): undefined reference to `serdev_device_set_flow_control'
hci_ldisc.c:(.text+0xb5c): undefined reference to `serdev_device_set_tiocm'
This adds a dependency to avoid the broken configuration.
Fixes: 7841d55480 ("Bluetooth: hci_uart_set_flow_control: Fix NULL deref when using serdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This was introduced by the rework adding PM support:
drivers/bluetooth/hci_bcm.c: In function 'bcm_device_exists':
drivers/bluetooth/hci_bcm.c:156:22: error: 'struct bcm_device' has no member named 'hu'
if (device && device->hu && device->hu->serdev)
^~
The pointer is not available otherwise, so I'm enclosing
all references in an #ifdef here.
Fixes: 8a92056837 ("Bluetooth: hci_bcm: Add (runtime)pm support to the serdev driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip
for wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4
with BCM4345 rev C0 firmware.
This patch defines the firmware subversion.
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_bcm platform-device hack which was used to implement
power management for ACPI devices is being replaced by a
serial-device-bus implementation.
Unfortunately, when the corresponding change to the ACPI code lands (a
change that will stop enumerating and registering the serial-device-node
child as a platform device) PM will break silently unless serdev
TTY-port controller support has been enabled. Specifically, hciattach
(btattach) would still succeed, but power management would no longer
work.
Although this is strictly a runtime dependency, let's make the driver
depend on SERIAL_DEV_CTRL_TTYPORT, which is the particular serdev
controller implementation used by the ACPI devices currently managed by
this driver, to avoid breaking PM without anyone noticing.
Note that the driver already has a (build-time) dependency on the serdev
bus code.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As the overwriting of IRQ polarity to active low occurs during the driver
probe using 'bt_dev_warn' to display the warning results in '(null)' being
displayed for the device. This patch uses 'dev_warn' to correctly display
the device in the warning instead.
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. As already done in hci_qca, add
struct hci_uart pointer to priv structure.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make the serdev driver use struct bcm_device as its driver data and share
all the pm / GPIO / IRQ related code paths with the platform driver.
After this commit the 2 drivers are in essence the same and the serdev
driver interface can be used for all ACPI enumerated HCI UARTs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use dev_get_drvdata instead of platform_get_drvdata in the suspend /
resume functions. This is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
So we need to make bcm_acpi_probe() suitable for use on non platform-
devices too, which means that we cannot rely on platform_get_irq()
getting called.
This commit modifies bcm_acpi_probe() to directly get the irq from
the ACPI resources, this is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After our previous changes, there is nothing platform specific about
bcm_platform_probe anymore, rename it to bcm_get_resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
This means that the serdev driver paths of hci_bcm.c also need to start
supporting (runtime)pm through GPIOs and a host-wake IRQ.
The hci_bcm code is already mostly independent of how the HCI gets
instantiated, but even though the code only cares about pdev->dev, it
was storing pdev itself in struct bcm_device.
This commit stores pdev->dev rather then pdev in struct bcm_device, this
is a preparation patch for adding (runtime)pm support to the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
Most of the code in bcm_platform_probe is actually not platform
specific and will work with any struct device passed to it, the one
platform specific call in bcm_platform_probe is platform_get_irq.
This commit moves platform_get_irq call to the platform-driver's bcm_probe
function, this is a preparation patch for adding (runtime)pm support to
the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since bcm_acpi_probe calls bcm_platform_probe, bcm_probe always ends up
calling bcm_platform_probe.
This commit simplifies things by making bcm_probe always call
bcm_platform_probe itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This commit fixes 2 issues with host-wake irq trigger type handling
in hci_bcm:
1) bcm_setup_sleep sets sleep_params.host_wake_active based on
bcm_device.irq_polarity, but bcm_request_irq was always requesting
IRQF_TRIGGER_RISING as trigger type independent of irq_polarity.
This was a problem when the irq is described as a GpioInt rather then
an Interrupt in the DSDT as for GpioInt-s the value passed to request_irq
is honored. This commit fixes this by requesting the correct trigger
type depending on bcm_device.irq_polarity.
2) bcm_device.irq_polarity was used to directly store an ACPI polarity
value (ACPI_ACTIVE_*). This is undesirable because hci_bcm is also
used with device-tree and checking for something like ACPI_ACTIVE_LOW
in a non ACPI specific function like bcm_request_irq feels wrong.
This commit fixes this by renaming irq_polarity to irq_active_low
and changing its type to a bool.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix a NULL pointer deref (hu->tty) when calling hci_uart_set_flow_control
on hci_uart-s using serdev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
pr_err(), dev_err() and pr_info() messages should terminated with
a new-line to avoid other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Retrieve BD address from the local-bd-address property.
This address must be unique and is usually added in the DT
by the bootloader which has access to the provisioned data.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the hdev setup function since wcnss-bt does not have
persistent memory to store an allocated BD address. The device is therefore
marked as unconfigured if no BD address has been previously retrieved.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The Broadcom controller on the Raspberry Pi3 sends an empty packet with
packet type 0x00 after launching the firmware. This will cause logging
of errors.
Bluetooth: hci0: Frame reassembly failed (-84)
Since this seems to be an intented behaviour of the controller, handle
it gracefully by parsing that empty packet with packet type 0x00 and
then just simply report it as diagnostic packet.
With that change no errors are logging and the packet itself is actually
recorded in the Bluetooth monitor traces.
< HCI Command: Broadcom Launch RAM (0x3f|0x004e) plen 4
Address: 0xffffffff
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Launch RAM (0x3f|0x004e) ncmd 1
Status: Success (0x00)
= Vendor Diagnostic (len 0)
< HCI Command: Broadcom Update UART Baud Rate (0x3f|0x0018) plen 6
00 00 00 10 0e 00 ......
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Update UART Baud Rate (0x3f|0x0018) ncmd 1
Status: Success (0x00)
< HCI Command: Reset (0x03|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
Status: Success (0x00)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.
Tested/compatible with bcm43438 (RPi3).
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commands that read the basic vendor information about the Broadcom
controller are duplicated for UART and USB devices. Combine them into a
single function to reduce the code complexity.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Not all Broadcom controller support the 4Mbps operational speed on UART
devices. This is because the UART clock setting changes might not be
supported.
< HCI Command: Broadcom Write UART Clock Setting (0x3f|0x0045) plen 1
01 .
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Write UART Clock Setting (0x3f|0x0045) ncmd 1
Status: Unknown HCI Command (0x01)
To support any operational speed higher than 3Mbps, support for this
command is required. With that respect it is better to not enforce any
operational speed by default. Only when its support is known, then allow
for higher operational speed.
This patch assigns the 4Mbps opertional speed only for devices
discovered through ACPI and leave all others at the default 115200.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
BT-Controller connected as platform non-root-hub device and
usb-driver initialize such device with wakeup disabled,
Ref. usb_new_device().
At present wakeup-capability get enabled by hid-input device from usb
function driver(e.g. BT HID device) at runtime. Again some functional
driver does not set usb-wakeup capability(e.g LE HID device implement
as HID-over-GATT), and can't wakeup the host on USB.
Most of the device operation (such as mass storage) initiated from host
(except HID) and USB wakeup aligned with host resume procedure. For BT
device, usb-wakeup capability need to enable form btusc driver as a
generic solution for multiple profile use case and required for USB remote
wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature
need to enable/disable with HCI interface up and down.
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the activity LED is solid on during continuous activity.
Blink the LED during continuous activity to match Windows driver
behavior.
Cards with activity LED:
power LED = solid on when up, off when down
activity LED = blinking during activity, off when idle
Cards without activity LED:
power LED = solid on when up, off when down, blinking during activity
(don't have such a card so I don't know if Windows driver does the same
thing)
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Keep power LED on during activity.
LED timer races with power LED disabling in hci_close(), resulting in
power LED left on after closing.
Stop LED timer before disabling power LED.
BTW. On cards without an activity LED, the behavior is a bit weird:
The LED is on after hci_open() but only until the first data transfer.
Then it's off in idle and on during activity.
It could be improved by keeping the LED on in idle and flashing during
activity.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Anycom CF-300 (HP C8249A) has both power and activity LEDs.
However the id read in bluecard_open() is 0x73 so the driver does not
enable the LEDs.
Remove the CARD_HAS_PCCARD_ID check to enable LEDs.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Force alignment value to the default one (1 byte) if uninitialized.
This fixes hci_ll serdev driver (alignment = 0) and avoid any further
issues with upcoming drivers.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We accidentally return success if the kmemdup() fails. It results in
a NULL dereference in the caller.
Fixes: 1110a2dbe6 ("Bluetooth: btrtl: Add RTL8822BE Bluetooth device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Nokia devices require the setup of its Public Bluetooth Device
Address and for that it is required to depend on vendor specific
commands. For Broadcom based Nokia devices, that is part of btbcm
module and can be selected via BT_BCM config option.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently we are calling usb_submit_urb directly to submit deferred tx
urbs after unanchor them.
So the usb_giveback_urb_bh would failed to unref it in usb_unanchor_urb
and cause memory leak:
unreferenced object 0xffffffc0ce0fa400 (size 256):
...
backtrace:
[<ffffffc00034a9a8>] __save_stack_trace+0x48/0x6c
[<ffffffc00034b088>] create_object+0x138/0x254
[<ffffffc0009d5504>] kmemleak_alloc+0x58/0x8c
[<ffffffc000345f78>] __kmalloc+0x1d4/0x2a0
[<ffffffc0006765bc>] usb_alloc_urb+0x30/0x60
[<ffffffbffc128598>] alloc_ctrl_urb+0x38/0x120 [btusb]
[<ffffffbffc129e7c>] btusb_send_frame+0x64/0xf8 [btusb]
Put those urbs in tx_anchor to avoid the leak, and also fix the error
handling.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed alignment of all block comments.
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove unnecessary static on local variable hst.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the object file size.
This issue was detected using Coccinelle and the
following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the object file size.
This log is the output of the size command, before and after the code
change:
before:
text data bss dec hex filename
4029 2528 128 6685 1a1d drivers/bluetooth/btwilink.o
after:
text data bss dec hex filename
4007 2472 64 6543 198f drivers/bluetooth/btwilink.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Convert hci_ll to use hci_uart_unregister_device().
This simplifies the _remove() handler as well as fixes a
potential race condition on unload.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabor.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Several drivers have the same (and incorrect) code in their
_remove() handler.
Coalesce this into a shared function.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's been numerous reported instances where BTUSB_QCA_ROME
bluetooth controllers stop functioning upon resume from suspend. These
devices seem to be losing power during suspend. Patch will detect a status
change on resume and perform a reset.
Signed-off-by: Leif Liddy <leif.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
pm_runtime_disable() is called in the _close() handler.
Since we call the _close() handler on remove, there is no need to
call pm_runtime_disable() a second time.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only cancel any ongoing work after making sure, that no new work
can be scheduled. This fixes a race condition in the remove handler.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed this coding style erro
./drivers/bluetooth/btqca.c:84: ERROR: code indent should use tabs where possible
Signed-off-by: Joan Jani <igiann@hotmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of no IRQ resource associated to the bcm_device, requesting
IRQ should return an error in order to not enable low power mgmt.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
This patch adds the device ID for the bluetooth chip used in the
Broadcom BCM43430 SDIO WiFi / UART BT chip.
Successfully tested using Firmware version 0x0182
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reported-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Just like the T100TA the host-wake irq on the Asus T100CHI is
active low. Having a quirk for this is actually extra important on the
T100CHI as it ships with a bluetooth keyboard dock, which does not
work properly without this quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_bcm proto is able to operate without bcm platform device linked
to its uart port. In that case, firmware can be applied, but there is
no power operation (no gpio/irq resources mgmt).
However, the current implementation breaks this use case because of
reporting a ENODEV error in the bcm setup procedure if bcm_request_irq
fails (which is the case if no bcm device linked).
Fix this by removing bcm_request_irq error forwarding.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The structure hci_serdev_client_ops does not need to be in global scope
and is not modified, so make it static.
Cleans up sparse warning:
"symbol 'hci_serdev_client_ops' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Joe and Bjørn suggested that it'd be nicer to not have the
cast in the fairly common case of doing
*(u8 *)skb_put(skb, 1) = c;
Add skb_put_u8() for this case, and use it across the code,
using the following spatch:
@@
expression SKB, C, S;
typedef u8;
identifier fn = {skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Note that due to the "S", the spatch isn't perfect, it should
have checked that S is 1, but there's also places that use a
sizeof expression like sizeof(var) or sizeof(u8) etc. Turns
out that nobody ever did something like
*(u8 *)skb_put(skb, 2) = c;
which would be wrong anyway since the second byte wouldn't be
initialized.
Suggested-by: Joe Perches <joe@perches.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assingment if ->probe() fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to manage the external clock provided to the WiLink combo chip
as it's needed for any of the transport interfaces.
To avoid breaking platforms not yet specifying the external clock, we make
it optional. In case the clock is successfully fetched during ->probe(),
let's manage it via the ->open|close() callbacks, to make sure the device
get properly powered on/off.
Fixes: ea45267873 ("arm64: dts: hikey: Fix WiFi support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add compatible values for WiLink chips from 128x and 180x series.
Also the DT binding already contained compatible values for the 127x
series, but the driver did not. This brings the list on par with
the list from wlcore (the wifi driver).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The caller (hci_core) still owns the skb in case of error, releasing
it inside the send function can lead to use-after-free errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When __hci_cmd_sync() fails, download_firmware() should also fail, and
the same error value should be returned as PTR_ERR(skb).
Without this fix, download_firmware() will return a success when it actually
failed in __hci_cmd_sync().
Fixes: 371805522f ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We see the following build failure with CONFIG_BT_HCIUART_NOKIA=y and
CONFIG_BT_HCIUART_H4=n:
drivers/bluetooth/hci_nokia.c: In function 'nokia_recv':
drivers/bluetooth/hci_nokia.c:644:18: error: implicit declaration of function 'h4_recv_buf' [-Werror=implicit-function-declaration]
...
Fix this by selecting the BT_HCIUART_H4 symbol like all the other users
of the protocoll.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_UART_PROTO_READY is in the set state, the Data Link protocol
layer (proto) is bound to the HCI UART driver. This state allows the
registered proto function pointers to be used by the HCI UART driver.
When unbinding (closing) the Data Link protocol layer, the proto
function pointers much be prevented from being used immediately before
running the proto close function pointer. Otherwise, there is a risk
that a proto non-close function pointer is used during or after the
proto close function pointer is used. The consequences are likely to
be a kernel crash because the proto close function pointer will free
resources used in the Data Link protocol layer.
Therefore, add a reader writer lock (rwlock) solution to prevent the
close proto function pointer from running by using write_lock_irqsave()
whilst the other proto function pointers are protected using
read_lock(). This means HCI_UART_PROTO_READY can safely be cleared
in the knowledge that no proto function pointers are running.
When flag HCI_UART_PROTO_READY is put into the clear state,
proto close function pointer can safely be run. Note
flag HCI_UART_PROTO_SET being in the set state prevents the proto
open function pointer from being run so there is no race condition
between proto open and close function pointers.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We see the following link error with CONFIG_BT_HCIUART=y,
CONFIG_BT_HCIUART_LL=y and CONFIG_SERIAL_DEV_BUS=m:
drivers/built-in.o: In function 'll_close':
supp.c:(.text+0x55add4): undefined reference to 'serdev_device_close'
supp.c:(.text+0x55add4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_close'
drivers/built-in.o: In function 'll_open':
supp.c:(.text+0x55aed0): undefined reference to 'serdev_device_open'
supp.c:(.text+0x55aed0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_open'
drivers/built-in.o: In function `hci_ti_probe':
supp.c:(.text+0x55b00c): undefined reference to 'hci_uart_register_device'
supp.c:(.text+0x55b00c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'hci_uart_register_device'
drivers/built-in.o: In function `ll_setup':
supp.c:(.text+0x55b08c): undefined reference to 'serdev_device_set_flow_control'
supp.c:(.text+0x55b08c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_set_flow_control'
supp.c:(.text+0x55b324): undefined reference to 'serdev_device_set_baudrate'
supp.c:(.text+0x55b324): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_set_baudrate'
drivers/built-in.o: In function 'll_init':
supp.c:(.init.text+0x1b508): undefined reference to '__serdev_device_driver_register'
supp.c:(.init.text+0x1b508): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol '__serdev_device_driver_register'
Fix this by dependig BT_HCIUART_LL on the BT_HCIUART_SERDEV symbol.
This implies a dependency on BT_HCIUART and hci_ll.c is only compiled in
if SERIAl_DEV_BUS is built in or SERIAL_DEV_BUS and BT_HCIUART are
modules.
Fixes: 371805522f ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before attempting to schedule a work-item onto hu->write_work in
hci_uart_tx_wakeup(), check that the Data Link protocol layer is
still bound to the HCI UART driver.
Failure to perform this protocol check causes a race condition between
the work queue hu->write_work running hci_uart_write_work() and the
Data Link protocol layer being unbound (closed) in hci_uart_tty_close().
Note hci_uart_tty_close() does have a "cancel_work_sync(&hu->write_work)"
but it is ineffective because it cannot prevent work-items being added
to hu->write_work after cancel_work_sync() has run.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_tx_wakeup()
which prevents scheduling of the work queue when HCI_UART_PROTO_READY
is in the clear state. However, note a small race condition remains
because the hci_uart_tx_wakeup() thread can run in parallel with the
hci_uart_tty_close() thread so it is possible that a schedule of
hu->write_work can occur when HCI_UART_PROTO_READY is cleared. A complete
solution needs locking of the threads which is implemented in a future
commit.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before attempting to dequeue a Data Link protocol encapsulated message,
check that the Data Link protocol is still bound to the HCI UART driver.
This makes the code consistent with the usage of the other proto
function pointers.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_dequeue()
and return NULL if the Data Link protocol is not bound.
This is needed for robustness as there is a scheduling race condition.
hci_uart_write_work() is scheduled to run via work queue hu->write_work
from hci_uart_tx_wakeup(). Therefore, there is a delay between
scheduling hci_uart_write_work() to run and hci_uart_dequeue() running
whereby the Data Link protocol layer could become unbound during the
scheduling delay. In this case, without the check, the call to the
unbound Data Link protocol layer dequeue function can crash.
It is noted that hci_uart_tty_close() has a
"cancel_work_sync(&hu->write_work)" statement but this only reduces
the window of the race condition because it is possible for a new
work-item to be added to work queue hu->write_work after the call to
cancel_work_sync(). For example, Data Link layer retransmissions can
be added to the work queue after the cancel_work_sync() has finished.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before attempting to send a HCI message, check that the Data Link
protocol is still bound to the HCI UART driver. This makes the code
consistent with the usage of the other proto function pointers.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_send_frame()
and return -EUNATCH if the Data Link protocol is not bound.
This also allows hci_send_frame() to report the error of an unbound
Data Link protocol layer. Therefore, it assists with diagnostics into
why HCI messages are being sent when the Data Link protocol is not
bound and avoids potential crashes.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ensure that HCI_UART_PROTO_READY is cleared before close(hu) is
called which closes the Data Link protocol layer.
Therefore, add the missing bit clear of HCI_UART_PROTO_READY to
hci_uart_init_work() so that the flag is cleared when
hci_register_dev fails.
Without the fix, the functions of the Data Link protocol layer could
potentially be accessed after that layer has been closed. This
could lead to a crash as memory would have been freed in that layer.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_register_dev() fails, hu->hdev should be set to NULL before
freeing hdev. This avoids potential use of hu->hdev after it has been
freed.
This commit sets hu->hdev to NULL before calling hci_free_dev() in error
handling scenarios in hci_uart_init_work() and hci_uart_register_dev().
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If hci_register_dev() returns an error in hci_uart_init_work()
then the HCI_UART_REGISTERED bit gets erroneously set due to
a missing return statement. Therefore, add the missing return
statement.
The consequence of the missing return is that the HCI UART is not
registered but HCI_UART_REGISTERED is set which allows the code
to think that hu->hdev is safe to access but hu->hdev has been
freed so could lead to a crash.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With CONFIG_SERIAL_DEV_BUS=m, the hci_serdev.o file does not actually
get built into hci_uart.o as the Makefile doesn't pick it up, leading
to a link error with anything referring to it:
ERROR: "hci_uart_register_device" [drivers/bluetooth/hci_nokia.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
Changing this in the Makefile would cause another problem when
hci_uart itself is built-in and cannot reference symbols from the
serdev module.
This tries to address both problems by introducing a new hidden
Kconfig symbol that controls both the compilation of hci_serdev.o
and whether the Nokia driver can be selected. This seems to address
the problem for me, though there might be a better way to do it.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid NULL pointer dereference occurring due to freeing
skb containing an error pointer. It can easily be triggered
by using the driver with broken uart (i.e. due to misconfigured
pinmuxing).
Fixes: 371805522f ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Turns out that the LL protocol and the TI-ST are the same thing AFAICT.
The TI-ST adds firmware loading, GPIO control, and shared access for
NFC, FM radio, etc. For now, we're only implementing what is needed for
BT. This mirrors other drivers like BCM and Intel, but uses the new
serdev bus.
The firmware loading is greatly simplified by using existing
infrastructure to send commands. It may be a bit slower than the
original code using synchronous functions, but the real bottleneck is
likely doing firmware load at 115.2kbps.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are no users of hci_uart_init_tty, so remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a driver for the Nokia H4+ protocol, which is used
at least on the Nokia N9, N900 & N950.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For bluetooth protocol driver only supporting serdev it makes
sense to follow common practice and built them into their own
module.
Such modules need access to hci_uart_register_device and
hci_uart_tx_wakeup for using the common protocol helpers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device driver may need to communicate with the UART
device while the Bluetooth device is closed (e.g. due
to interrupts).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds library functions for serdev based BT drivers. This is largely
copied from hci_ldisc.c and modified to use serdev calls. There's a little
bit of duplication, but I avoided intermixing this as the ldisc code should
eventually go away.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
[Fix style issues reported by Pavel]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This will be used by Nokia's H4+ protocol, which
uses 2-byte aligned packets.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sanity check of interrupt number in interrupt handler is unnecessary and
confusion, remove it.
Reported-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 74cdad37cd ("Bluetooth: hci_intel: Add runtime PM support")
Fixes: 1ab1f239bf ("Bluetooth: hci_intel: Add support for platform driver")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 0395ffc1ee ("Bluetooth: hci_bcm: Add PM for BCM devices")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Else is not generally useful after a break or return
Signed-off-by: Prasanna Karthik <pkarthik@outlook.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Until now the driver supports only ACPI enumeration. Nevertheless
Intel Edison SoM has Broadcom Wi-Fi + BT chip and neither ACPI nor DT
enumeration mechanism.
Enable pure platform driver in order to support Intel Edison SoM.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The message concerning missing config files for 8723b, 8821a, and
8761a should have been issued with BT_INFO() rather than BT_ERR() as
this condition is not fatal. After looking at that code, I have
reworked the logic to log such messages only if the device needs such a
config file. At the moment, only the 8822b fits that description.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: 陆朱伟 <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Intel Bluetooth device 9160/9260 also
known as ThunderPeak(ThP) for UART.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
This patch uses a hw_variant value read from the device during
runtime to form the firmware filenames instead of using a constant
value, so it can support multiple prouducts.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Multiple new hardware variants are planned and the simple if statement
would get really complicated and unreadable. So instead replace it with
a simple switch statement.
The change is applied to both USB and UART.
Based-on-patch-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_bcm driver currently does not prepare/unprepare the clock and
goes directly to enable, but as the documentation for clk_enable says,
clk_prepare must be called before clk_enable.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
trivial fix to spelling mistake in debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By moving these client drivers to use RPMSG instead of the direct SMD
API we can reuse them ontop of the newly added GLINK wire-protocol
support found in the 820 and 835 Qualcomm platforms.
As the new (RPMSG-based) and old SMD implementations are mutually
exclusive we have to change all client drivers in one commit, to make
sure we have a working system before and after this transition.
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile-testing fails when QCOM_SMD is a loadable module:
drivers/bluetooth/built-in.o: In function `btqcomsmd_send':
btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send'
drivers/bluetooth/built-in.o: In function `btqcomsmd_probe':
btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel'
btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata'
This clarifies the dependency to allow compile-testing only when
SMD is completely disabled, otherwise the dependency on QCOM_SMD
will make sure we can link against it.
Fixes: e27ee2b16b ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
trivial fix to spelling mistake in error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
trivial fix to spelling mistake in BT_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver only has runtime but no build time dependency with QCOM_SMD &&
QCOM_WCNSS_CTRL. So it can be built for testing purposes if COMPILE_TEST
option is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM2E96 ID is used by the ECS EF20 laptop, and BCM2E95 is present
in the Weibu F3C. Both are now logged as:
hci0: BCM: chip id 82
hci0: BCM43341B0 (002.001.014) build 0000
hci0: BCM (002.001.014) build 0158
The ECS vendor kernel predates the host-wakeup support in hci_bcm but
it explicitly has a comment saying that the GPIO assignment needs to be
reordered for BCM2E96:
1. (not used in vendor driver)
2. Device wakeup
3. Shutdown
For both devices in question, the DSDT has these GPIOs listed in order
of GpioInt, GpioIo, GpioIo. And if we use the first one listed (GpioInt)
as the host wakeup, that interrupt handler fires while doing bluetooth
I/O.
I am assuming the convention of GPIO ordering has been changed for these
new device IDs, so lets use the new ordering on such devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some btbcm devices require more time to complete its reset process.
They won't reply any hci command until reset is done.
[ 17.218554] Bluetooth: hci0 command 0x1001 tx timeout
[ 25.214999] Bluetooth: hci0: BCM: Reading local version info failed (-110)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The irq_of_parse_and_map will return 0 as a invalid irq.
Set irq_bt to -1 in this case, so that the btmrvl resume/suspend code
would not try to enable/disable it.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's much the same as what we did for mwifiex in:
b9da4d2 mwifiex: avoid double-disable_irq() race
"We have a race where the wakeup IRQ might be in flight while we're
calling mwifiex_disable_wake() from resume(). This can leave us
disabling the IRQ twice.
Let's disable the IRQ and enable it in case if we have double-disabled
it."
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Marvell devices may have many gpio pins, and hence for wakeup
on these out-of-band pins, the chip needs to be told which pin is
to be used for wakeup, using an hci command.
Thus, we read the pin number etc from the device tree node and send
a command to the chip.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some onboard BT chips (e.g. Marvell 8997) contain a wakeup pin that
can be connected to a gpio on the CPU side, and can be used to wakeup
the host out-of-band. This can be useful in situations where the
in-band wakeup is not possible or not preferable (e.g. the in-band
wakeup may require the USB host controller to remain active, and
hence consuming more system power during system sleep).
The oob gpio interrupt to be used for wakeup on the CPU side, is
read from the device tree node, (using standard interrupt descriptors).
A devcie tree binding document is also added for the driver. The
compatible string is in compliance with
Documentation/devicetree/bindings/usb/usb-device.txt
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use a label to remove the repetetive cleanup, for error cases.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Lukas Wunner