PLATFORM_DEVID_AUTO can be used to have the platform core assign a
unique ID instead of manually creating one with IDA. Do this in all
applicable drivers.
Link: http://lkml.kernel.org/r/20160531204313.20979-1-afd@ti.com
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since many temperature sensors come "preconfigured" with a lower
precision, people are stuck at that precision when running on a kernel
based device (unlike the Dallas 1Wire library for e.g. Arduino, which
supports writing the configuration/scratchpad). This patch adds write
support for the scratchpad/precision registers via w1_slave sysfs.
Signed-off-by: Ben Sen <0.x29a.0@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kstrtoint() returns -ERANGE then "tmp" is uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polaykov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit enables the active pullup (APU bit) by default for
the DS2482 1-Wire master.
>From the DS2482 datasheet:
"The APU bit controls whether an active pullup (controlled slew-rate
transistor) or a passive pullup (Rwpu resistor) will be used to drive
a 1-Wire line from low to high. When APU = 0, active pullup is disabled
(resistor mode). Active Pullup should always be selected unless there is
only a single slave on the 1-Wire line."
According to the module author, Ben Gardner:
"It doesn't look like active pullup would cause any hurt if there
is only a single slave."
And my tests with multiple and single slaves on 1-Wire bus
confirms that.
This active pullup can be manually disabled using the introduced
module parameter:
active_pullup = 0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_process() calls try_to_freeze(), but the thread doesn't mark itself
freezable through set_freezable(), so the try_to_freeze() call is useless.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hdq_usecount was set to zero after a successful read, so
omap_hdq_put could not properly free resources which leads
e.g. to increasing usecounts in lsmod output
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's stop using legacy platform driver hooks for power management and
switch to using the standard dev_pm_ops-based hooks.
Also, instead of guarding PM methods with #ifdef CONFIG_PM annotate them
as __maybe_unused as it provides better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, memsetting and kfreeing the device is bad behaviour. The
device will have a reference count of 1 and hence can cause trouble
because it has kfree'd. Proper way to handle a failed device_register is
to call put_device right after it fails.
Signed-off-by: Levente Kurusa <levex@linux.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use module_pci_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pci_register_driver(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { pci_unregister_driver(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pci_driver;
@@
-module_exit(e);
+module_pci_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed there was a problem here because Smatch complained:
drivers/w1/slaves/w1_therm.c:416 w1_seq_show() warn:
inconsistent returns 'mutex:&sl->master->mutex'.
Locked on: line 416
Unlocked on: line 413
The problem is that we lock ->mutex but we unlock ->bus_mutex on error.
David Fries says that ->bus_mutex is correct and ->mutex is incorrect.
Fixes: d9411e57dc ('w1: Add support for DS28EA00 sequence to w1-therm')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The W1_42_FINISHED_BYTE is 0xFF so the cast means the condition is
never true.
Fixes: d9411e57dc ('w1: Add support for DS28EA00 sequence to w1-therm')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add i2c alias to enable autoloading of the module for device specified
in device-tree.
Signed-off-by: Ludek Hlavacek <ludek_h@seznam.cz>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides support for the DS28EA00 digital thermometer.
The DS28EA00 provides an additional two pins for implementing a sequence
detection algorithm. This feature allows you to determine the physical
location of the chip in the 1-wire bus without needing pre-existing
knowledge of the bus ordering. Support is provided through the sysfs
w1_seq file. The file will contain a single line with an integer value
representing the device index in the bus starting at 0.
Signed-off-by: Matt Campbell <mattrcampbell@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A temperature conversion can take 750 ms and when possible the
w1_therm slave driver drops the bus_mutex to allow other bus
operations, but that includes operations such as a periodic slave
search, which can remove this slave when it is no longer detected.
If that happens the sl->family_data will be freed and set to NULL
causing w1_slave_show to crash when it wakes up.
Signed-off-by: David Fries <David@Fries.net>
Reported-By: Thorsten Bschorr <thorsten@bschorr.de>
Tested-by: Thorsten Bschorr <thorsten@bschorr.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of 1-Wire devices commonly associated with physical access control
systems are attached/generate presence for as short as 100 ms - hence
the tens-to-hundreds milliseconds scan intervals are required.
Signed-off-by: Dmitry Khromov <dk@icelogic.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a new
subsystem, "coresight" has been added. Full details are in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSODosACgkQMUfUDdst+ykSNwCfcqx1Z3rQzbLwSrR2sa1fV3Zb
yEAAniJoLZ4ZkoQK4/1ozsFc31q+gXNm
=/epr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
1/ change request_module call to zero-pad single digit
family numbers. This appears to be the intention of
the code, but not what it actually does.
This means that the alias created for W1_FAMILY_SMEM_01
might actually be useful.
2/ Define a family name for the BQ27000 battery charge monitor.
Unfortunately this is the same number as W1_FAMILY_SMEM_01
so if both a compiled on a system, one module might need to
be blacklisted.
3/ Add a MODULE_ALIAS for the bq27000.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has no 'compatible' string and so is not found when
using device-tree.
Add one with value to match
hdqw1w: 1w@480b2000 {
device in omap3.dtsi.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adjust the bulk message timeout to the other ones (1000ms). Otherwise the
following dmesg errors can be seen on a Raspberry Pi:
[ 31.492386] Failed to read 1-wire data from 0x81: err=-110.
[ 31.504168] 0x81: count=-110, status:
[ 31.613404] Failed to read 1-wire data from 0x81: err=-110.
[ 31.621915] 0x81: count=-110, status:
[ 43.260968] Failed to read 1-wire data from 0x81: err=-110.
[ 43.270998] 0x81: count=-110, status:
[ 43.379959] Failed to read 1-wire data from 0x81: err=-110.
[ 43.388854] 0x81: count=-110, status:
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94859308a2 "w1: new w1_ds2406 driver" added a new driver
that uses the crc16 library, but didn't ensure that the core is
there. This adds the necessary Kconfig statements, just like we
have it for other w1 drivers.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Scott Alfter <scott@alfter.us>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the "masters"
subdirectory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the main "w1"
directory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the "slaves"
subdirectory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some preliminary work at making use of this driver led me to implement
CRC-16 checks on read and write to deal with the occasional glitchiness of
the 1-Wire bus. The revised driver (attached) returns an I/O error if the
CRC check fails. When reading the chip's state, either you get a valid
indication or you get an I/O error. When changing its state, either the
change is successful or an I/O error is returned.
Signed-off-by: Scott Alfter <scott@alfter.us>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace spaces at beginning of the string with tabs, and replace foo * bar with foo *bar in a pointer declaration.
Signed-off-by: Thomas Wood <tommyandrena@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the read/write bit operations
takes from 60 us to 120 us.
This patch optimizes mxc_w1_ds2_touch_bit() function to use proper
value for such delay. Nevertheless, a small margin for the timeout has
been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a software reset for 1-Wire module at driver startup.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the reset procedure and
"presence" pulse takes 511 and 512 us, respectively. Measurement for
i.MX27 is about 1100 us. There is no need to wait Reset+Presence
more than this time.
This patch optimizes mxc_w1_ds2_reset_bus() function to use proper
value for delay after w1 bus reset. Nevertheless, a small margin for
the timeout has been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W1 reset_bus() should return zero if slave device is present.
This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_process_callbacks() expects to be called with dev->list_mutex held,
but it is the fact only in w1_process(). __w1_remove_master_device()
calls w1_process_callbacks() after it releases list_mutex.
The patch fixes __w1_remove_master_device() to acquire list_mutex
for w1_process_callbacks().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: David Fries <david@fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applications can submit a set of commands in one packet to the kernel,
and in some cases it is required such as reading the temperature
sensor results. This adds an option W1_CN_BUNDLE to the flags of
cn_msg to request the kernel to reply in one packet for efficiency.
The cn_msg flags now check for unknown flag values and return an error
if one is seen. See "Proper handling of unknown flags in system
calls" http://lwn.net/Articles/588444/
This corrects the ack values returned as per the protocol standard,
namely the original ack for status messages and seq + 1 for all others
such as the data returned from a read.
Some of the common variable names have been standardized as follows.
struct cn_msg *cn
struct w1_netlink_msg *msg
struct w1_netlink_cmd *cmd
struct w1_master *dev
When an argument and a function scope variable would collide, add req_
to the argument.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__w1_attach_slave_device calls device_add which calls w1_bus_notify
which calls the w1_bq27000 slave driver, which calls
platform_device_add and device_add and deadlocks on getting
&(&priv->bus_notifier)->rwsem as it is still held in the previous
device_add. This avoids the problem by processing the family
add/remove outside of the slave device_add call.
Commit 47eba33a09 introduced this deadlock and added
a KOBJ_ADD, as the add was already reported in device_register two add
events were being sent. This change suppresses the device_register
add so that any slave device sysfs entries are setup before the add
goes out.
Belisko Marek reported this change fixed the deadlock he was seeing on
ARM device tree, while testing on my x86-64 system never saw the
deadlock.
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the message type is W1_MASTER_CMD or W1_SLAVE_CMD, then a reference
is taken when searching for the slave or master device. If there
isn't any following data m->len (mlen is a copy) is 0 and packing up
the message for later execution is skipped leaving nothing to
decrement the reference counts.
Way back when, m->len was checked before the search that increments the
reference count, but W1_LIST_MASTERS has no additional data, the check
was moved in 9be62e0b2f causing this bug.
This change reorders to put the check before the reference count is
incremented avoiding the problem.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, __raw_{read,write}b() functions was be replaced with
simple {read,write}b() variants.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove old and currently wrong address of the FSF from license
parts of the code.
- Remove unused #include and sort remaining headers alphabetically.
- Remove unised definitions.
- Add definitions for bit-fields.
- Add missing module owner field.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix mxc_w1_ds2_reset_bus() return value.
According to i.MX reference manual, "presence status" reflected
in the bit 6 of control register.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configuration for masters and slaves is included only if W1 symbol
enabled, so no reason to check it once more.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_get_gpio() might return -EPROBE_DEFER meaning that the driver
providing the gpio isn't ready yet. If that happens for the first gpio
the resulting kernel output without this patch is:
w1-gpio somename: Failed to parse DT
platform somename: Driver w1-gpio requests probe deferral
The first message is misleading and so is suppressed with this patch.
Further if determining the gpio to switch the external pullup yields
-EPROBE_DEFER this error should be passed back to the caller instead of
just continuing without pullup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 64 bit systems, a large value for "long tmp" is truncated when
assigning to "int md->max_slave_count" so we still end up with a value
less than one despite the "tmp < 1" check.
This is more of a problem for static checkers than a real life issue,
but it's simple enough to fix.
Acked-by: David Fries <david@fries.net>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts ds1wm.c from commit d3a8a9dbb9.
Of the three files changed ds1wm.c ds2490.c and w1_netlink.c, it turns out
ds1wm.c was locking bus_mutex, but inside the loop and I missed it.
Reverting ds1wm.c to the previous version.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bus_mutex needs to be taken to serialize access to a specific bus.
netlink wasn't updated when bus_mutex was added and was calling
without that lock held, and not all of the masters were holding the
bus_mutex in a search. This was causing the ds2490 hardware to stop
responding when both netlink and /sys slaves were executing bus
commands at the same time.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch the code documentation format style to DocBook format, enable
DocBook documentation generation, and fix some comments.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first line printed from w1_slave gives the context of the w1
device. So does the second line, but if the CRC check failed, the
second line contains the last successful result. It is confusing when
it prints the temperature next to the line that might be a previous
conversion and has nothing to do with that printed temperature value.
Modify the code to store the last good conversion in family_data,
which is designed for custom data structures.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware search was failing without the COMM_RST flag. Enabled
the flag and rewrote the function to handle more than one buffer of
results and to continuing where the search left off. Remove hardware
search note from the limitations now that it works. The "w1: ds2490
USB setup fixes" change went from 23.16 seconds to about 3 seconds,
this takes the time for the search down to .307346 seconds.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling usb_reset_configuration after usb_set_interface resets the
interface that was just selected, so call reset first.
Using alternative 3 greatly speeds the one wire search.
alt 0 or 1, 10ms int, 23.16 seconds
alt 2 or 3, 1ms int, 2.99 to 3.05 seconds
Use usb_interrupt_msg not usb_bulk_msg as it is an interrupt pipe
(bulk worked, it was just technically the wrong call).
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a #define for the usb vendor request type, clear the status
byte and use that instead of a magic offset in checking if idle.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unicast one wire replies back to the sender portid to avoid multiple
programs getting each other's messages, especially as the response
can't be uniquely identified with the sequence coming from the
requesting program when both programs generate the same id. Continue
to broadcast events such as add/remove master/slave devices.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows replying only to the requestor portid while still
supporting broadcasting. Pass 0 to portid for the previous behavior.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Netlink is a socket interface and is expected to be asynchronous.
Clients can now make w1 requests without blocking by making use of the
w1_master thread to process netlink commands which was previously only
used for doing an automatic bus search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new commands to add, remove, and list slave devices through
the netlink interface. This can be useful to skip the search on a
static network. They could previously only be added or removed
through automatic search or sysfs, and this allows a program to only
use netlink.
Only allocate memory when needed, so move kzalloc into w1_get_slaves
where it was used.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Search will detect at most max_slave_count devices per run, if there
are more pick up the next search where the previous left off.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_max_slave_count is only used to abort the search early
or take a fast search (when 1), so there isn't any reason to not allow
it to be updated through sysfs. Memory is not allocated based on
the current value and 10 is a rather low base number, increasing to
64, and printing a message the first time the count is reached and
there were more devices to discover to let the user know why not
all the devices were found.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's valid to set the search count to 0 to stop searching, so don't
wake up the search thread to not search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before 63706172f3 "rework kthread_stop()" kthread_should_stop()
always returned false when called from a non-kthread task, after it
would oops as a non-kthread didn't have that structure and netlink was
calling search from a thread which wasn't a kthread. 9d1817cab2
"w1: fix oops when w1_search is called from netlink connector",
modified the code to avoid calling kthread_stop from a netlink thread.
Introduce a w1_master flag and bit W1_ABORT_SEARCH to identify abort
to cleanly support both kthread and netlink search abort. A search
can take seconds to run, so it is important to abort early if the
hardware is removed in the middle of a search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Marcin Jurkowski <marcin1j@gmail.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Sven Geggus <lists@fuchsschwanzdomain.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous logic,
if (avail > 8) {
store slave;
return;
}
send data; clear;
The logic error is, if there isn't space send the buffer and clear,
but the slave wasn't added to the now empty buffer loosing that slave
id. It also should have been "if (avail >= 8)" because when it is 8,
there is space.
Instead, if there isn't space send and clear the buffer, then there is
always space for the slave id.
Signed-off-by: David Fries <David@Fries.net>
Cc: stable@vger.kernel.org
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Base frequency should be as close as possible to 1 MHz. This patch
adds warnings when clock is unreliable, according to i.MX datasheet.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Private field "clkdiv" is not used outside "probe", so there are
no reason to keep it in driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On architectures where long is more then 32 bits, modifying a 32-bit field
with set_bit (and other atomic bit operations) may cause bytes following
the field to by modified.
Because the endianness of the bits within a field is the native endianness
of the CPU[1], on big-endian machines, bit number zero is in the last byte
of the field.
Therefore, `set_bit(0, ptr)' on a 64-bit big-endian machine is roughly
equivalent to `((char *)ptr)[7] |= 1', and since w1 driver uses a 32-bit
field for holding the flags, this causes bytes beyond the field to be
modified.
[1] From Documentation/atomic_ops.txt:
Native atomic bit operations are defined to operate on objects
aligned to the size of an "unsigned long" C data type, and are
least of that size. The endianness of the bits within each
"unsigned long" are the native endianness of the cpu.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first DT gpio is necessary for this driver, but errors returned for
of_get_gpio are ignored.
This patch adds a return value check for the first of_get_gpio.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
request_module for w1 slave modules needs to be called with the w1
master mutex unlocked. Because w1_attach_slave_device gets always(?)
called with mutex locked, we need to temporarily unlock the w1 master
mutex for the loading of the w1 slave module.
Signed-off by: Hans-Frieder Vogt <hfvogt@gmx.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a check to make sure that fops are only called if they have
been defined by the slave module.
Without this check modules like w1_smem cause a NULL pointer dereference
bug.
Signed-off by: Hans-Frieder Vogt <hfvogt@gmx.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The driver core clears the driver data to NULL after device_release or on
probe failure. Thus, it is not needed to manually clear the device driver
data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usage of strict_strtol() is not preferred, because strict_strtol() is
obsolete. Thus, kstrtol() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: David Stevenson <david@avoncliff.com>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Michael Arndt <michael@scriptkiller.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lets w1 slave drivers declare an attribute group, and not have to
create/destroy sysfs files directly. All w1 slave drivers will be fixed
to use this field up in follow-on patches to this one.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we have 2 sysfs files for the w1 slave devices, let the driver core
create / destroy them automatically by setting the default attribute
group for them, saving code and housekeeping logic.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W1 slave sysfs files are created _after_ userspace is notified that the
device has been added to the system. Fix that race by moving the
creation/remove of the files to the bus notifier that is there for doing
this type of thing.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power-up timing
The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled. When this occurs, the P0 port
does not respond to the Channel Access Write command. For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below. The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first. This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.
Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD
[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew F. Davis