Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SkyHawk-R devices should use v2 of cq_create command.
BE3/BE2 devices can use version 0 of the command to create a CQ.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R requires V1 version of GET_FUNCTION_CONFIG cmd to be used for
querrying resources available per function.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC could lockup in the transmit path when it tries
to insert VLAN in a specific ipv6 packet.
1) Identify the packet which can cause this.
2) Check if the firmware provides a workaround to prevent this.
3) If workaround is not present, drop the packet.
4) If the firmware provides a workaround, insert the VLAN tag in the
packet and inform the firmware to skip further VLAN insertions.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GET_PROFILE_CONFIG_V1 cmd for BE3-R, to query the maximum number of
TX rings available per function. On SH-R the same is queried via the
GET_FUNCTION_CONFIG cmd.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid flashing BE3 UFI on BE3-R chip by verifying asic_revision
number of the chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R and BE3-R (SuperNIC profile) require V2 version
of TXQ_CREATE cmd to be used.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed as the earlier method of manipulating this register via PCI
Config space is disallowed by certain Hypervisors.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the PF driver is unloaded and re-loaded while VFs are attached
to VMs, it loses control of its VFs.
The PF driver now uses the newly defined/created GET_IFACE_LIST cmd
(available in FW ver >= 4.6) to query the if_id of the VFs
(enabled in its previous life). The PF driver then uses the if_id for
further VF configuration.
The GET_IFACE_MAC_LIST cmd has also implemented in BE3 FW for PF to
query pmac-ids used by its VFs.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->generation was being incorrectly set as BE_GEN3 for Skyhawk-R.
Replace generation usage with XXX_chip() macros to identify the chip.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW flashing code, even though it works correctly, makes some hidden
assumptions about buffer sizes. This is causing code analysers to
report error. Cleanup FW flashing code to remove these hidden assumptions.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver should enable VF so that VF goes to ready state in
new Lancer FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF does not have privileges to execute many commands. When VFs try
to execute those commands there are unnecessary error messages.
Fix this by executing only those commands for which VF has privilege.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use Lancer specific command to set QoS for VF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assumes FW resource counts and capabilities while creating queues and
using functionality like RSS. This causes driver load to fail in FW configs
where resources and capabilities are reduced. Fix this by querying FW
configuration during probe and using resources and capabilities accordingly.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) link_status_query() is always called to query the link-speed (speed
after applying qos). When there is no qos setting, link-speed is derived from
port-speed. Do all this inside this routine and hide this from the callers.
2) adpater->phy.forced_port_speed is not being set anywhere after being
initialized. Get rid of this variable.
3) Ignore async link_speed notifications till the initial value has been
fetched from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All invocations of this routine use the same type value.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ability of driver to transmit packets depends on logical state
of the link. Ignore physical link status.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorporated review comment from Eric Dumazet. Added description
about different RSS hash types which adapter is capable of.
Will add support for ETHTOOL_GRXFH and ETHTOOL_SRXFX as suggested
by Ben Hutchings in a later patch.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After FW download, activate new FW by invoking FW reset.
Recreate rings once new FW is operational.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke only required initialization routines for Lancer.
Remove invocation of unnecessary routines.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the hardware statistics structure to accomodate statistics for skyhawk.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Permanent MAC is wrongly supplied in create iface command. Call the
command with no MAC address and then MAC address should be later queried
and applied.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yWfr
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.
* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
IB/mlx4: Fix mlx4_ib_add() error flow
IB/core: Fix IB_SA_COMP_MASK macro
IB/iser: Fix error flow in iser ep connection establishment
IB/mlx4: Increase the number of vectors (EQs) available for ULPs
RDMA/cxgb4: Add query_qp support
RDMA/cxgb4: Remove kfifo usage
RDMA/cxgb4: Use vmalloc() for debugfs QP dump
RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
RDMA/cxgb4: Add DB Overflow Avoidance
RDMA/cxgb4: Add debugfs RDMA memory stats
cxgb4: DB Drop Recovery for RDMA and LLD queues
cxgb4: Common platform specific changes for DB Drop Recovery
cxgb4: Detect DB FULL events and notify RDMA ULD
RDMA/cxgb4: Drop peer_abort when no endpoint found
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
mlx4_core: Change bitmap allocator to work in round-robin fashion
RDMA/nes: Don't call event handler if pointer is NULL
RDMA/nes: Fix for the ORD value of the connecting peer
...
Patch re-spin.
Incorporated review comments by Ben Hutchings.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Increase MSI-X vectors by 5 for RoCE traffic.
- Add macro to check roce support on a device.
- Add device-specific doorbell and MSI-X vector fields shared with NIC
functionality.
- Provide RoCE driver registration and deregistration functions.
- Add support functions which will be invoked on adapter add/remove
and port up/down events.
- Traverse through the list of adapters to invoke callback functions.
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roland Dreier <roland@purestorage.com>
MCC Response CQEs are processed as part of NAPI poll routine and
also synchronously. If MCC completions are consumed by NAPI poll
routine, wrong status is returned to synchronously waiting routine.
Fix this by getting status of MCC command from command response
instead of response CQEs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool get settings was not displaying all the settings correctly.
use the get_phy_info to get more information about the PHY to fix this.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: Fixed up the bad typecasting pointed out by David...
In the current design 8 TXQs are serviced by 1 EQ, while each RSS queue
is serviced by a separate EQ. This is being changed as follows:
- Upto 8 EQs will be used (based on the availabilty of msix vectors).
Each EQ will handle 1 RSS and 1 TX ring. The default non-RSS RX queue and
MCC queue are handled by the last EQ.
- On cards which provide support, upto 8 RSS rings will be used, instead
of the current limit of 4.
The new design allows spreading the TX multi-queue completion processing
across multiple CPUs unlike the previous design.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs use get mac list command to get their mac address. The format of
this command has changed. Update driver to use the new format.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also rename a few counters appropritely and delete 2 counters that are not
implemented in HW.
vlan_mismatch_drops does not exist in BE3 and is accounted for in
address_mismatch_drops. Do the same thing for BE2 and Lancer.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net gets an async link status notification from the FW when it creates
an MCC queue. There are some cases in which this gratuitous notification
is not received from FW. To cover this explicitly query the link status
in be_open().
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SR-IOV implementation is Lancer has changed in following ways -
1)PF driver assigns one MAC addresses for VF using COMMON_SET_IFACE_MAC_LIST.
2)VF driver queries its MAC address using COMMON_GET_IFACE_MAC_LIST command
and assigns it to its interface.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented eeprom dump using ethtool feature for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement register dump using ethtool for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize if_handle, vf_if_handle and vf_pmac_id with "-1" so that in
failure cases when be_clear() is called, we can skip over
if_destroy/pmac_del cmds if they have not been created.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HW is in multi-channel mode based on the skew/IPL, there are
4 functions per port and so not enough resources to create multiple
RX/TX rings for each function.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the code for VF setup/teardown done by a PF (if_create,
mac_add_config, link_status_query etc) is scattered; this patch
refactors this code into be_vf_setup() and be_vf_clear(). The
if_create/if_destroy/mac_addr_query cmds are now called after the MCCQ
is created; so these cmds are now modified to use the MCCQ instead of
MBOX.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix provides a newly flashed FW version (appended, in braces)
along with the currently running FW version via ethtool. The newly
flashed version runs only after a system reset.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the Emulex driver into drivers/net/ethernet/emulex/ and
make the necessary Kconfig and Makefile changes.
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somnath Kotur