Instead of using a private copy of struct net_device_stats in struct
happy_meal, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
bigmac, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function gem_begin_auto_negotiation dereference
the pointer ep before testing if it's null. This
patch add a check on ep before dereferencing it.
Fixes: 92552fdda5 ("net: sun: sungem: use new api
ethtool_{get|set}_link_ksettings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunvnet netdev is connected to the controlling ldom's vswitch
for network bridging. However, for higher performance between ldoms,
there also is a channel between each client ldom. These connections are
represented in the sunvnet driver by a queue for each ldom. The driver
uses select_queue to tell the stack which queue to use by tracking the mac
addresses on the other end of each port. When a connected ldom shuts down,
the driver receives an LDC_EVENT_RESET and the port is removed from the
driver, thus a queue with no ldom on the other end will never be selected
for Tx.
The driver was trying to reinforce the "don't use this queue" notion with
netif_tx_stop_queue() and netif_tx_wake_queue(), which really should only
be used to signal a Tx queue is full (aka XOFF). This misuse of queue
state resulted in NETDEV WATCHDOG messages and lots of unnecessary calls
into the driver's tx_timeout handler. Simply removing these takes care
of the problem.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure multicast packets get counted in the device.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track our used and unused queue indexies correctly. Otherwise, as ports
dropped out and returned, they all eventually ended up with the same
queue index.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this driver, there is a "port" created for the connection to each of
the other ldoms; a netdev queue is mapped to each port, and they are
collected under a single netdev. The generic netdev statistics show
us all the traffic in and out of our network device, but don't show
individual queue/port stats. This patch breaks out the traffic counts
for the individual ports and gives us a little view into the state of
those connections.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ldom VM is bound, the network vswitch infrastructure is set up for
it, but was being forced 'UP' by the userland switch configuration script.
When 'UP' but not actually connected to a running VM, the ipv6 neighbor
probes fail (not a horrible thing) and start cluttering up the kernel logs.
Funny thing: these are debug messages that never actually show up, but
we do see the net_ratelimited messages that say N callbacks were
suppressed.
This patch defers the netif_carrier_on() until an actual link has been
established with the VM, as indicated by receiving an LDC_EVENT_UP from
the underlying LDC protocol. Similarly, we take the link down when we
see the LDC_EVENT_RESET. Now when we see the ndo_open(), we reset the
link to get things talking again.
Orabug: 25525312
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ldmvsw driver is specifically for supporting the ldom virtual
networking by running in the primary ldom and using the LDC to connect
the remaining ldoms to the outside world via a bridge. With TSO and GSO
supported while connected the bridge, things tend to misbehave as seen
in our case by delayed packets, enough to begin triggering retransmits
and affecting overall throughput. By turning off advertised support for
TSO and GSO we restore stable traffic flow through the bridge.
Orabug: 23293104
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New version and simplify the print code.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RCU read lock is grabbed first thing in sunvnet_start_xmit_common()
so it always needs to be released. This removes the conditional release
in the dropped packet error path and removes a couple of superfluous
calls in the middle of the code.
Reported-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of gotos for handling the incoming events made this code
harder to read and support than it should be. This patch straightens
out and clears up the logic.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow the underlying LDC and outstanding memory operations
to potentially catch up with the driver's Tx requests, add a memory
barrier before checking again for available tx descriptors.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been several changes since the first version of this code, so
we bump the version number. While we're at it, we can simplify the
version printing a bit and drop a couple lines of code.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vio_dring_state *dr variable is unused in maybe_tx_wakeup().
As the comments indicate, we call maybe_tx_wakeup() whenever we
get a STOPPED LDC message on the port. If the queue is stopped,
we want to wake it up so that we will send another START message
at the next TX and trigger the consumer to drain the dring.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the sunvnet_common code was split out for use by both sunvnet
and the newer ldmvsw, it was made into a static kernel library, which
limits the usefulness of sunvnet and ldmvsw as loadables, since most
of the real work is being done in the shared code. Also, this is
simply dead code in kernels that aren't running the LDoms.
This patch makes the sunvnet_common into a dynamically loadable
module and makes sunvnet and ldmvsw dependent on sunvnet_common.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__bitwise__ used to mean "yes, please enable sparse checks
unconditionally", but now that we dropped __CHECK_ENDIAN__
__bitwise is exactly the same.
There aren't many users, replace it by __bitwise everywhere.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Akced-by: Lee Duncan <lduncan@suse.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
sunbmac uses '__u32' for dma handle while invoking kernel DMA APIs,
instead of using dma_addr_t. This hasn't caused any 'incompatible
pointer type' warning on SPARC because until now dma_addr_t is of
type u32. However, recent changes in SPARC ATU (iommu) enables 64bit
DMA and therefore dma_addr_t becomes of type u64. This makes
'incompatible pointer type' warnings inevitable.
e.g.
drivers/net/ethernet/sun/sunbmac.c: In function ‘bigmac_ether_init’:
drivers/net/ethernet/sun/sunbmac.c:1166: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
This patch resolves above compiler warning.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sunqe uses '__u32' for dma handle while invoking kernel DMA APIs,
instead of using dma_addr_t. This hasn't caused any 'incompatible
pointer type' warning on SPARC because until now dma_addr_t is of
type u32. However, recent changes in SPARC ATU (iommu) enables 64bit
DMA and therefore dma_addr_t becomes of type u64. This makes
'incompatible pointer type' warnings inevitable.
e.g.
drivers/net/ethernet/sun/sunqe.c: In function ‘qec_ether_init’:
drivers/net/ethernet/sun/sunqe.c:883: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
drivers/net/ethernet/sun/sunqe.c:885: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
This patch resolves above compiler warnings.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes an issue with the ldmvsw driver where
the network connection of a guest domain becomes non-functional after
the guest domain has panic'd and rebooted.
The root cause was determined to be from the following series of
events:
1. Guest domain panics - resulting in the guest no longer processing
network packets (from ldmvsw driver)
2. The ldmvsw driver (in the control domain) eventually exerts flow
control due to no more available tx drings and stops the tx queue
for the guest domain
3. The LDC of the network connection for the guest is reset when
the guest domain reboots after the panic.
4. The LDC reset event is received by the ldmvsw driver and the ldmvsw
responds by clearing the tx queue for the guest.
5. ldmvsw waits indefinitely for a DATA ACK from the guest - which is
the normal method to re-enable the tx queue. But the ACK never comes
because the tx queue was cleared due to the LDC reset.
To fix this issue, in addition to clearing the tx queue, re-enable the
tx queue on a LDC reset. This prevents the ldmvsw from getting caught in
this deadlocked state of waiting for a DATA ACK which will never come.
Signed-off-by: Aaron Young <Aaron.Young@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cassini: min_mtu 60, max_mtu 9000
niu: min_mtu 68, max_mtu 9216
sungem: min_mtu 68, max_mtu 1500 (comments say jumbo mode is broken)
sunvnet: min_mtu 68, max_mtu 65535
- removed sunvnet_change_mut_common as it does nothing now
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Checkpatch updates for sunvnet.c and sunvnet_common.c.
Signed-off-by: Aaron Young <aaron.young@oracle.com>
Signed-off-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Alexandre Chartre <Alexandre.Chartre@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ldmvsw.c driver
Details:
The ldmvsw driver very closely follows the sunvnet.c code and makes
use of the sunvnet_common.c code for core functionality.
A significant difference between sunvnet and ldmvsw driver is
sunvnet creates a network interface for each vnet-port *parent*
node in the MD while the ldmvsw driver creates a network interface
for every vsw-port node in the Machine Description (MD).
Therefore the netdev_priv() for sunvnet is a vnet structure while
the netdev_priv() for ldmvsw is a vnet_port structure.
Vnet_port structures allocated by ldmvsw have the vsw bit set.
When finding the net_device associated with a port, the common code keys
off this bit to use either the net_device found in the vnet_port or the
net_device in the vnet structure (see the VNET_PORT_TO_NET_DEVICE() macro in
sunvnet_common.h). This scheme allows the common code to work with
both drivers with minimal changes.
Similar to Xen, network interfaces created by the ldmvsw driver will always
have a HW Addr (i.e. mac address) of FE:FF:FF:FF:FF:FF and each will be
assigned the devname "vif<cfg_handle>.<port_id>" - where <cfg_handle> and
<port_id> are a unique handle/port pair assigned to the associated
vsw-port node in the MD.
Signed-off-by: Aaron Young <aaron.young@oracle.com>
Signed-off-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Alexandre Chartre <Alexandre.Chartre@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify sunvnet common code and data structures to be compatible
with both sunvnet and ldmvsw drivers.
Details:
Sunvnet operates on "vnet-port" nodes which appear in the Machine
Description (MD) in a guest domain. Ldmvsw operates on "vsw-port"
nodes which appear in the MD of a service domain.
A difference between the sunvnet driver and the ldmvsw driver is
the sunvnet driver creates a network interface (i.e. a struct net_device)
for every vnet-port *parent* "network" node. Several vnet-ports may appear
under this common parent network node - each corresponding to a common parent
network interface. Conversely, since bridge/vswitch software will need
to interface with every vsw-port in a system, the ldmvsw driver creates
a network interface (i.e. a struct net_device) for every vsw-port - not
every parent node as with sunvnet. This difference required some special
handling in the common code as explained below.
There are 2 key data structures used by the sunvnet and ldmvsw drivers
(which are now found in sunvnet_common.h):
1. struct vnet_port
This structure represents a vnet-port node in sunvnet and a vsw-port
in the ldmvsw driver.
2. struct vnet
This structure represents a parent "network" node in sunvnet and a parent
"virtual-network-switch" node in ldmvsw.
Since the sunvnet driver allocates a net_device for every parent "network"
node, a net_device member appears in the struct vnet. Since the ldmvsw
driver allocates a net_device for every port, a net_device member was
added to the vnet_port. The common code distinguishes which structure
net_device member to use by checking a 'vsw' bit that was added to the
vnet_port structure. See the VNET_PORT_TO_NET_DEVICE() marco in
sunvnet_common.h.
The netdev_priv() in sunvnet is allocated as a vnet. The netdev_priv()
in ldmvsw is a vnet_port. Therefore, any place in the common code
where a netdev_priv() call was made, a wrapper function was implemented
in each driver to first get the vnet and/or vnet_port (in a driver
specific way) and pass them as newly added parameters to the common
functions (see wrapper funcs: vnet_set_rx_mode() and vnet_poll_controller()).
Since these wrapper functions call __tx_port_find(), __tx_port_find() was
moved from the common code back into sunvnet.c. Note - ldmvsw.c does not
require this function.
These changes also required that port_is_up() be made
into a common function and thus it was given a _common suffix and
exported like the other common functions.
A wrapper function was also added for vnet_start_xmit_common() to pass a
driver-specific function arg to return the port associated with a given
struct sk_buff and struct net_device. This was required because
vnet_start_xmit_common() grabs a lock prior to getting the associated
port. Using a function pointer arg allowed the code to work unchanged
without risking changes to the non-trivial locking logic in
vnet_start_xmit_common().
Signed-off-by: Aaron Young <aaron.young@oracle.com>
Signed-off-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Alexandre Chartre <Alexandre.Chartre@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split sunvnet.c into sunvnet.c and sunvnet_common.c.
Details:
Since the sunvnet and ldmvsw drivers will both use common sunvnet code,
move the functions (and support functions) anticipated to be common code
from sunvnet.c to sunvnet_common.c. Similarly, sunvnet.h was renamed to
sunvnet_common.h. The sunvnet_common.c code will be compiled into the
kernel and act as a library of functions that are linked by either
(or both) drivers when loaded.
Function names for external functions in sunvnet_common.c (to be
called by both the sunvnet and ldmvsw drivers) were tagged with a "_common"
suffix to clearly designate them as common functions.
No functional changes as of yet... just moved code verbatim to the new
sunvnet_common.c/h files.
Makefile/Kconfig support added to build sunvnet_common.c file. The code
is included in the kernel if SUN_LDOMS is defined/selected.
NOTE - per the SubmittingPatches documentation, since the code was just
moved from one file another, the code was NOT checkpatch'd in this commit
to aid in review.
Signed-off-by: Aaron Young <aaron.young@oracle.com>
Signed-off-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Alexandre Chartre <Alexandre.Chartre@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use sunvnet perf trace macros to monitor LDC message exchange state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
vnet_fullcsum() accesses ip_hdr() and transport header to compute
the checksum for IPv4 packets, so these need to be initialized in
skb created in vnet_rx_one().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ls /sys/devices/channel-devices/vnet-port-0-0/net' is missing without
this change, and applications like NetworkManager are looking in
sysfs for the information.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: a3138df9 ("[NIU]: Add Sun Neptune ethernet driver.")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_dma_burst_advice() was added by e24c2d963a ("[PATCH] PCI: DMA
bursting advice") but apparently never used. Remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <monstr@monstr.eu> # microblaze
CC: David S. Miller <davem@davemloft.net>
This patch goes through and replaces wmb/rmb with dma_wmb/dma_rmb in cases
where the barrier is being used to order writes or reads to just memory and
doesn't involve any programmed I/O.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser