With the earlier sanity fixes to
driver_deferred_probe_check_state() it should be usable for the
pinctrl logic here.
So tweak the logic to use driver_deferred_probe_check_state()
instead of driver_deferred_probe_check_state_continue()
Cc: linux-pm@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200225050828.56458-4-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On X86 plaform, if the CONFIG_OF is not selected, and set the
CONFIG_SPRD_SC9860 as 'm', that will cause below waring:
WARNING: unmet direct dependencies detected for PINCTRL_SPRD
Depends on [n]: PINCTRL [=y] && OF [=n] && (ARCH_SPRD || COMPILE_TEST [=y])
Selected by [m]:
- PINCTRL_SPRD_SC9860 [=m] && PINCTRL [=y]
Thus move the configuration dependency under CONFIG_PINCTRL_SPRD_SC9860
to fix the warning.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/eeb12d7843fb06f80e19f98eb25711231c3b610f.1583205650.git.baolin.wang7@gmail.com
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register_mappings is called in the pdata case, however a call to
pinctrl_unregister_mappings is missing causing the mappings to be leaked
on driver unbind. Add the missing call to correct this issue.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154214.13916-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kref_init starts with the reference count at 1, which will be balanced
by the pinctrl_put in pinctrl_unregister. The additional kref_get in
pinctrl_claim_hogs will increase this count to 2 and cause the hogs to
not get freed when pinctrl_unregister is called.
Fixes: 6118714275 ("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154142.13860-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200227185837.GA4469@embeddedor
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These comparisons should be >= instead of > to prevent accessing one
element beyond the end of the hw->soc->pins[] array.
Fixes: 3de7deefce ("pinctrl: mediatek: Check gpio pin number and use binary search in mtk_hw_pin_field_lookup()")
Fixes: 184d8e13f9 ("pinctrl: mediatek: Add support for pin configuration dump via debugfs.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200218055247.74s2xa7veqx2do34@kili.mountain
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: b96eea718b ("pinctrl: fsl: add scu based pinctrl support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/bd7ad5fd755739a6d8d5f4f65e03b3ca4f457bd2.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the second loop of ingenic_pinconf_set(), it annotates the switch
default case as unreachable(). The annotation is technically correct,
because that same case would have resulted in an early function return
in the previous loop.
However, the compiled code is suboptimal. GCC seems to work extra hard
to ensure that the unreachable code path triggers undefined behavior.
The function would fall through to start executing whatever function
happens to be next in the compilation unit.
This is problematic because:
a) it adds unnecessary 'ensure undefined behavior' logic, and
corresponding i-cache footprint; and
b) it's less robust -- if a bug were to be introduced, falling through
to the next function would be catastrophic.
Yet another issue is that, while objtool normally understands
unreachable() annotations, there's one special case where it doesn't:
when the annotation occurs immediately after a 'ret' instruction. That
happens to be the case here because unreachable() is immediately before
the return.
Remove the unreachable() annotation and replace it with a comment. This
simplifies the code generation and changes the unreachable error path to
just silently return instead of corrupting execution.
This fixes the following objtool warning:
drivers/pinctrl/pinctrl-ingenic.o: warning: objtool: ingenic_pinconf_set() falls through to next function ingenic_pinconf_group_set()
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/bc20fdbcb826512cf76b7dfd0972740875931b19.1582212881.git.jpoimboe@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the gxl driver, the sdio cmd and clk pins are inverted. It has not caused
any issue so far because devices using these pins always take both pins
so the resulting configuration is OK.
Fixes: 0f15f500ff ("pinctrl: meson: Add GXL pinctrl definitions")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Link: https://lore.kernel.org/r/1582204512-7582-1-git-send-email-nbelin@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200217185437.GA20901@embeddedor
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.
Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.
Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller hardware does not distinguish IRQs intended for
wakeup from other IRQs, so we must mask non-wakeup IRQs in software to
prevent inadvertent wakeups. This is accomplished at the irqchip level
via the IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200117213340.47714-2-samuel@sholland.org
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl irqchip may be connected to an irqchip that implements the
.irq_set_wake callback, such as the R_INTC on A31 and newer sunxi SoCs.
In order for GPIOs to be able to trigger wakeup, the IRQ from the
pinctrl to the upper irqchip must also be enabled for wakeup. Since the
kernel's IRQ core already manages the "wake_depth" of each IRQ, no
additional accounting is needed in the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200117213340.47714-1-samuel@sholland.org
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_ARCH_R8A7795 was split in CONFIG_ARCH_R8A77950 and
CONFIG_ARCH_R8A77951 in commit b925adfceb ("soc: renesas: Add
ARCH_R8A7795[01] for existing R-Car H3"), so its users can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218112557.5924-1-geert+renesas@glider.be
As of commit 4adeabd042 ("pinctrl: sh-pfc: Remove hardcoded IRQ
numbers"), only a single operation needs to be performed after finding
the wanted pin. Hence decrease the needed attention span of the casual
reader by replacing the goto by a direct return.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200212090200.11106-1-geert+renesas@glider.be
Add checks for legacy function GPIO descriptors:
1. Function GPIOs must have a name,
2. Names must be unique,
3. Enum ID values must be unique.
This exposes bugs like those fixed in
- commit 884caadad1 ("pinctrl: sh-pfc: sh7734: Fix duplicate
TCLK1_B"),
- commit 55b1cb1f03 ("pinctrl: sh-pfc: sh7264: Fix CAN function
GPIOs"),
- commit 02aeb2f215 ("pinctrl: sh-pfc: sh7269: Fix CAN function
GPIOs"),
- commit db9c07272c ("sh: sh7264: Remove bogus SSU GPIO function
definitions"),
- commit b4fba344a2 ("sh: sh7269: Remove bogus SSU GPIO function
definitions").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-14-geert+renesas@glider.be
Add checks for data register descriptors:
1. Register addresses must be unique.
2. Enum ID values must be unique.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-13-geert+renesas@glider.be
Add checks for drive strength register descriptors:
1. Register addresses must be unique,
2. Register fields must be non-overlapping,
3. Referred pins must exist.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-10-geert+renesas@glider.be
Improve the checks for pin group descriptors:
1. Introduce a local variable for the current group, to make the
checks easier to read,
2. Pin group names must be unique.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-9-geert+renesas@glider.be
Improve the checks for pin function descriptors:
1. Merge declaration and assignment of the local variable for the
current pin function,
2. Pin function names must be unique.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-8-geert+renesas@glider.be
Improve the checks for pin descriptors:
1. Introduce local variables for the current pin, to make the checks
easier to read,
2. Pins must have a name,
3. Fix double printing of identical pin names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-7-geert+renesas@glider.be
Add a helper to verify that enum IDs are unique, and use it to validate
the enum ID arrays in config register descriptors.
This exposes bugs like those fixed in:
- commit 805f635703 ("pinctrl: sh-pfc: r8a7778: Fix duplicate
SDSELF_B and SD1_CLK_B"),
- commit 884caadad1 ("pinctrl: sh-pfc: sh7734: Fix duplicate
TCLK1_B"),
- commit 2a069a9281 ("pinctrl: sh-pfc: sh7264: Fix Port K I/O
Register 0 definition").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-6-geert+renesas@glider.be
Add a helper to verify that register addresses are unique, and use it to
validate config register descriptors.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-5-geert+renesas@glider.be
Add a helper to check if two strings are identical, skipping NULL
pointers. This simplifies callers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-4-geert+renesas@glider.be
Add helpers to report errors and warnings, and to increase the
corresponding counters. This simplifies callers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-3-geert+renesas@glider.be
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c: In function mtk_hw_pin_field_lookup:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:70:39: warning:
variable e set but not used [-Wunused-but-set-variable]
Since commit 3de7deefce ("pinctrl: mediatek: Check gpio pin
number and use binary search in mtk_hw_pin_field_lookup()"),
it is not used any more, so remove it, also remove redundant
assignment to variable c, it will be assigned a new value later
before used.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200218023625.14324-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DA9062 is a mfd pmic device which supports 5 GPIOs. The GPIOs can
be used as input, output or have a special use-case.
The patch adds the support for the normal input/output use-case.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200108104746.1765-4-m.felsch@pengutronix.de
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prepares the platform data to be easier to extend for more GPIOs.
Except of this there is no functional change.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1581166975-22949-3-git-send-email-stefan.wahren@i2se.com
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group names by function do not match their respective structures and
documentation defined names.
This fixes following errors when groups names defined on documentation are used:
[ 4.262778] pinctrl-s700 e01b0000.pinctrl: invalid group "sd0_d1_mfp" for function "sd0"
[ 4.271394] pinctrl-s700 e01b0000.pinctrl: invalid group "sd0_d2_d3_mfp" for function "sd0"
[ 4.280248] pinctrl-s700 e01b0000.pinctrl: invalid group "sd1_d0_d3_mfp" for function "sd0"
[ 4.289122] pinctrl-s700 e01b0000.pinctrl: invalid group "sd0_cmd_mfp" for function "sd0"
Fixes: 81c9d563cc (pinctrl: actions: Add Actions Semi S700 pinctrl driver)
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Link: https://lore.kernel.org/r/20200124133758.10089-1-matheus@castello.eng.br
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for pin configuration dump via catting
/sys/kernel/debug/pinctrl/$platform_dependent_path/pinconf-pins.
pinctrl framework had already support such dump. This patch implement the
operation function pointer to fullfill this dump.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-6-git-send-email-light.hsieh@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Refine mtk_pinconf_set()/mtk_pinconf_get() for backward compatibility to
previous MediaTek's bias-pull usage.
In PINCTRL_MTK that use pinctrl-mtk-common.c, bias-pull setting for pins
with 2 pull resistors can be specified as value for bias-pull-up and
bias-pull-down. For example:
bias-pull-up = <MTK_PUPD_SET_R1R0_00>;
bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
On the other hand, PINCTRL_MTK_PARIS use customized properties
"mediatek,pull-up-adv" and "mediatek,pull-down-adv" to specify bias-pull
setting for pins with 2 pull resistors.
This introduce in-compatibility in device tree and increase porting
effort to MediaTek's customer that had already used PINCTRL_MTK version.
Besides, if customers are not aware of this change and still write devicetree
for PINCTRL_MTK version, they may encounter runtime failure with pinctrl and
spent time to debug.
This patch adds backward compatible to previous MediaTek's bias-pull usage
so that Mediatek's customer need not use a new devicetree property name.
The rationale is that: changing driver implementation had better leave
interface unchanged.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-5-git-send-email-light.hsieh@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct cases for PIN_CONFIG_SLEW_RATE, PIN_CONFIG_INPUT_SCHMITT_ENABLE,
and PIN_CONFIG_OUTPUT_ENABLE -
Use variable ret to receive value in mtk_hw_get_value() (instead of
variable val) since pinconf_to_config_packed() at end of this function
use variable ret to pack config value.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-4-git-send-email-light.hsieh@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1.Refine mtk_pinconf_get():
Use only one occurrence of return at end of this function.
2.Refine mtk_pinconf_set():
2.1 Use only one occurrence of return at end of this function.
2.2 Modify case of PIN_CONFIG_INPUT_ENABLE -
2.2.1
Regard all non-zero setting value as enable, instead of always enable.
2.2.2
Remove check of ies_present flag and always invoke mtk_hw_set_value()
since mtk_hw_pin_field_lookup() invoked inside mtk_hw_set_value() has
the same effect of checking if ies control is supported.
[The rationale is that: available of a control is always checked
in mtk_hw_pin_field_lookup() and no need to add ies_present flag
specially for ies control.]
2.3 Simply code logic for case of PIN_CONFIG_INPUT_SCHMITT.
2.4 Add case for PIN_CONFIG_INPUT_SCHMITT_ENABLE and process it with the
same code for case of PIN_CONFIG_INPUT_SCHMITT.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-3-git-send-email-light.hsieh@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MediaTek's smartphone project actual usage does need to know current value
(in mA) in procedure of finding the best driving setting.
The steps in the procedure is like as follow:
1. set driving setting field in setting register as 0, measure waveform,
perform test, and etc.
2. set driving setting field in setting register as 1, measure waveform,
perform test, and etc.
...
n. set driving setting field in setting register as n-1, measure
waveform, perform test, and etc.
Check the results of steps 1~n and adopt the setting that get best result.
This procedure does need to know the mapping between current to register
value.
Therefore, setting driving without mapping current is more practical for
MediaTek's smartphone usage.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-2-git-send-email-light.hsieh@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1. Check if gpio pin number is in valid range to prevent from get invalid
pointer 'desc' in the following code:
desc = (const struct mtk_pin_desc *)&hw->soc->pins[gpio];
2. Improve mtk_hw_pin_field_lookup()
2.1 Modify mtk_hw_pin_field_lookup() to use binary search for accelerating
search.
2.2 Correct message after the following check fail:
if (hw->soc->reg_cal && hw->soc->reg_cal[field].range) {
rc = &hw->soc->reg_cal[field];
The original message is:
"Not support field %d for pin %d (%s)\n"
However, the check is on soc chip level, not on pin level yet.
So the message is corrected as:
"Not support field %d for this soc\n"
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-1-git-send-email-light.hsieh@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Restructure the checker to move all data definitions to the top, before
the code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-2-geert+renesas@glider.be
Add #include of <linux/pinctrl/machine.h> to fix build
warnings in pinctrl-pxa2xx.c. Fixes these warnings:
In file included from ../drivers/pinctrl/pxa/pinctrl-pxa2xx.c:24:0:
../drivers/pinctrl/pxa/../pinctrl-utils.h:36:8: warning: `enum pinctrl_map_type' declared inside parameter list [enabled by default]
enum pinctrl_map_type type);
^
../drivers/pinctrl/pxa/../pinctrl-utils.h:36:8: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Link: http://lkml.kernel.org/r/0024542e-cba9-8f13-6c18-32d0050a6007@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we
got rid of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips
along with the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much
improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt
map is provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML
DT bindings schema. (A first user of this.)
-----BEGIN PGP SIGNATURE-----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=PnK5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
Core changes:
- Document the usecases for the kernelspace vs userspace
handling of GPIOs.
- Handle MSI (message signalled interrupts) properly in the
core hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor
array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain
with GPIOLIB_IRQCHIP on top of the revert of the previous
buggy switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes.
-----BEGIN PGP SIGNATURE-----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=3Glg
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.6 kernel cycle.
This is a pretty calm cycle so far, nothing special going on really.
Some more changes will come in from the irqchip and pin control trees.
I also deleted an orphan include file for FMC that was dangling since
subsystem was removed.
Core changes:
- Document the usecases for the kernelspace vs userspace handling of
GPIOs.
- Handle MSI (message signalled interrupts) properly in the core
hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain with
GPIOLIB_IRQCHIP on top of the revert of the previous buggy
switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes"
* tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (48 commits)
MAINTAINERS: Replace Tien Hock Loh as Altera PIO maintainer
gpiolib: hold gpio devices lock until ->descs array is initialised
gpio: aspeed-sgpio: fixed typos
gpio: mvebu: clear irq in edge cause register before unmask edge irq
gpiolib: Lower verbosity when allocating hierarchy irq
gpiolib: Remove duplicated function gpio_do_set_config()
gpio: Fix the no return statement warning
gpio: wcd934x: Add support to wcd934x gpio controller
gpiolib: remove set but not used variable 'config'
gpio: vx855: fixed a typo
gpio: mockup: sort headers alphabetically
gpio: mockup: update the license tag
gpio: Remove the unused flags
gpiolib: Set lockdep class for hierarchical irq domains
gpio: thunderx: Switch to GPIOLIB_IRQCHIP
gpiolib: Add the support for the msi parent domain
gpiolib: Add support for the irqdomain which doesn't use irq_fwspec as arg
gpio: Add use guidance documentation
dt-bindings: gpio: wcd934x: Add bindings for gpio
gpio: altera: change to platform_get_irq_optional to avoid false-positive error
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
- Convert to reasonable timeouts for all CMD6 commands (updates for BKOPS,
CACHE_FLUSH and INAND_CMD38_ARG_EXT_CSD) for eMMC
- Respect f_max clock rate at card initialization
- Add gpiod_toggle_active_low() API
- Consolidate slot-gpio code by using gpiod_toggle_active_low()
MMC host:
- Add pinctrl_select_default_state() API
- Consolidate pintctrl code by using pinctrl_select_default_state()
- mmci: Support any block sizes for SDIO for some variants
- mmci: Enable reset control for stm32_sdmmc
- mmc_spi: Toggle SPI_CS_HIGH polarity rather than hard-coding it
- renesas_sdhi: Add support for the r8a77961 variant
- renesas_sdhi: A few minor improvements
- rockchip-dw-mshc: Add support for the rk3308 variant
- sdhci: Enable support for external DMA controllers
- sdhci: Fixup error path when sending CMD12
- sdhci-brcmstb: Add support for 7216b0 variant
- sdhci-brcmstb: Add support for command queuing (CQHCI)
- sdhci-brcmstb: Add support for eMMC HS400ES mode
- sdhci-msm: Add support for the sc7180 variant
- sdhci-msm: Add support for command queuing (CQHCI)
- sdhci-of-at91: Add support for the SAM9x60 variant
- sdhci-of-at91: Improve support for tunings
- sdhci-of-esdhc: A few fixups for some clock related issues
- sdhci-omap: Add support for the am335x and the am437x variants
- sdhci-omap: Improve support for erase operations
- sdhci-omap: Add support for external DMA
-----BEGIN PGP SIGNATURE-----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=L0cJ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"There are no updates for the MEMSTICK subsystem this time. But note
that I am also carrying a patch from the pinctrl tree, which has been
shared through an immutable branch.
Summary:
MMC core:
- Convert to reasonable timeouts for all CMD6 commands (updates for
BKOPS, CACHE_FLUSH and INAND_CMD38_ARG_EXT_CSD) for eMMC
- Respect f_max clock rate at card initialization
- Add gpiod_toggle_active_low() API
- Consolidate slot-gpio code by using gpiod_toggle_active_low()
MMC host:
- Add pinctrl_select_default_state() API
- Consolidate pintctrl code by using pinctrl_select_default_state()
- mmci: Support any block sizes for SDIO for some variants
- mmci: Enable reset control for stm32_sdmmc
- mmc_spi: Toggle SPI_CS_HIGH polarity rather than hard-coding it
- renesas_sdhi: Add support for the r8a77961 variant
- renesas_sdhi: A few minor improvements
- rockchip-dw-mshc: Add support for the rk3308 variant
- sdhci: Enable support for external DMA controllers
- sdhci: Fixup error path when sending CMD12
- sdhci-brcmstb: Add support for 7216b0 variant
- sdhci-brcmstb: Add support for command queuing (CQHCI)
- sdhci-brcmstb: Add support for eMMC HS400ES mode
- sdhci-msm: Add support for the sc7180 variant
- sdhci-msm: Add support for command queuing (CQHCI)
- sdhci-of-at91: Add support for the SAM9x60 variant
- sdhci-of-at91: Improve support for tunings
- sdhci-of-esdhc: A few fixups for some clock related issues
- sdhci-omap: Add support for the am335x and the am437x variants
- sdhci-omap: Improve support for erase operations
- sdhci-omap: Add support for external DMA"
* tag 'mmc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (89 commits)
mmc: core: Default to generic_cmd6_time as timeout in __mmc_switch()
mmc: block: Use generic_cmd6_time when modifying INAND_CMD38_ARG_EXT_CSD
mmc: core: Specify timeouts for BKOPS and CACHE_FLUSH for eMMC
mmc: sdhci-cadence: remove unneeded 'inline' marker
dt-bindings: mmc: rockchip-dw-mshc: add description for rk3308
dt-bindings: mmc: convert rockchip dw-mshc bindings to yaml
dt-bindings: mmc: convert synopsys dw-mshc bindings to yaml
mmc: sdhci-msm: Add CQHCI support for sdhci-msm
mmc: sdhci: Let a vendor driver supply and update ADMA descriptor size
mmc: sdhci-of-esdhc: fix serious issue clock is always disabled
mmc: sdhci-of-esdhc: fix transfer mode register reading
mmc: sdhci-brcmstb: Fix incorrect switch to HS mode
mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)
mmc: sdhci-brcmstb: Add shutdown callback
mmc: sdhci-brcmstb: Fix driver to defer on clk_get defer
mmc: sdhci-brcmstb: Add ability to use HS400ES transfer mode
dt-bindings: mmc: brcm,sdhci-brcmstb: Add support for 7216b0
mmc: core: limit probe clock frequency to configured f_max
mmc: sdhci-milbeaut: Remove redundant platform_get_irq error message
mmc: sdhci: fix an issue of mixing different types
...
platform_irq_count() and platform_get_irq() is the more generic
way (independent of device trees) to determine the count of available
interrupts. So use this instead.
As platform_irq_count() might return an error code (which
of_irq_count doesn't) some additional handling is necessary.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1576672860-14420-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver support for i.MX8MP.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1579052348-32167-2-git-send-email-Anson.Huang@nxp.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Tiger Lake appears to have _HID enumeration, thus driver has been updated
* Coffee Lake-S has the same IP as Sunrisepoint, thus ID has been added
* Baytrail has got more clean ups and bug fixes, such as direct IRQ handling
* Lynxpoint GPIO has been converted to true pin control driver
* The common driver now uses IRQ chip enumeration via GPIO chip
The following is an automated git shortlog grouped by driver:
baytrail:
- Replace WARN with dev_info_once when setting direct-irq pin to output
- Do not clear IRQ flags on direct-irq enabled pins
- Reuse struct intel_pinctrl in the driver
- Use local variable to keep device pointer
- Keep pointer to struct device instead of its container
- Use GPIO direction definitions
- Move IRQ valid mask initialization to a dedicated callback
- Group GPIO IRQ chip initialization
- Allocate IRQ chip dynamic
cherryview:
- Use GPIO direction definitions
intel:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Share struct intel_pinctrl for wider use
- Use GPIO direction definitions
lynxpoint:
- Update summary in the driver
- Switch to pin control API
- Add GPIO <-> pin mapping ranges via callback
- Implement ->pin_dbg_show()
- Add pin control operations
- Reuse struct intel_pinctrl in the driver
- Add pin control data structures
- Implement intel_gpio_get_direction callback
- Implement ->irq_ack() callback
- Move ownership check to IRQ chip
- Move lp_irq_type() closer to IRQ related routines
- Move ->remove closer to ->probe()
- Extract lp_gpio_acpi_use() for future use
- Convert unsigned to unsigned int
- Switch to memory mapped IO accessors
- Keep pointer to struct device instead of its container
- Relax GPIO request rules
- Assume 2 bits for mode selector
- Use standard pattern for memory allocation
- Use %pR to print IO resource
- Drop useless assignment
- Correct amount of pins
- Use raw_spinlock for locking
- Move GPIO driver to pin controller folder
sunrisepoint:
- Add Coffee Lake-S ACPI ID
- Add missing Interrupt Status register offset
tigerlake:
- Tiger Lake uses _HID enumeration
-----BEGIN PGP SIGNATURE-----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=+ZAJ
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.6-1
* Tiger Lake appears to have _HID enumeration, thus driver has been updated
* Coffee Lake-S has the same IP as Sunrisepoint, thus ID has been added
* Baytrail has got more clean ups and bug fixes, such as direct IRQ handling
* Lynxpoint GPIO has been converted to true pin control driver
* The common driver now uses IRQ chip enumeration via GPIO chip
The following is an automated git shortlog grouped by driver:
baytrail:
- Replace WARN with dev_info_once when setting direct-irq pin to output
- Do not clear IRQ flags on direct-irq enabled pins
- Reuse struct intel_pinctrl in the driver
- Use local variable to keep device pointer
- Keep pointer to struct device instead of its container
- Use GPIO direction definitions
- Move IRQ valid mask initialization to a dedicated callback
- Group GPIO IRQ chip initialization
- Allocate IRQ chip dynamic
cherryview:
- Use GPIO direction definitions
intel:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Share struct intel_pinctrl for wider use
- Use GPIO direction definitions
lynxpoint:
- Update summary in the driver
- Switch to pin control API
- Add GPIO <-> pin mapping ranges via callback
- Implement ->pin_dbg_show()
- Add pin control operations
- Reuse struct intel_pinctrl in the driver
- Add pin control data structures
- Implement intel_gpio_get_direction callback
- Implement ->irq_ack() callback
- Move ownership check to IRQ chip
- Move lp_irq_type() closer to IRQ related routines
- Move ->remove closer to ->probe()
- Extract lp_gpio_acpi_use() for future use
- Convert unsigned to unsigned int
- Switch to memory mapped IO accessors
- Keep pointer to struct device instead of its container
- Relax GPIO request rules
- Assume 2 bits for mode selector
- Use standard pattern for memory allocation
- Use %pR to print IO resource
- Drop useless assignment
- Correct amount of pins
- Use raw_spinlock for locking
- Move GPIO driver to pin controller folder
sunrisepoint:
- Add Coffee Lake-S ACPI ID
- Add missing Interrupt Status register offset
tigerlake:
- Tiger Lake uses _HID enumeration
* Fix Interrupt Status register offset for Intel Sunrisepoint PCH-H.
The following is an automated git shortlog grouped by driver:
sunrisepoint:
- Add missing Interrupt Status register offset
-----BEGIN PGP SIGNATURE-----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=7pOQ
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.5-3
* Fix Interrupt Status register offset for Intel Sunrisepoint PCH-H.
The following is an automated git shortlog grouped by driver:
sunrisepoint:
- Add missing Interrupt Status register offset
Turns out that Tiger Lake GPIO will be enumerated using _HID method where
there is only a single ACPI device and multiple BARs so rework the driver
to support that scheme instead.
Fixes: c9ccf71fc8 ("pinctrl: intel: Add Intel Tiger Lake pin controller support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Coffee Lake-S PCH has the same GPIO hardware than Sunrisepoint-H
PCH but the ACPI ID is different. Add this new ACPI ID to the list of
supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use platform_get_irq_optional() instead of platform_get_irq() to avoid
below error message during probe:
[ 0.589121] iproc-gpio 66424800.gpio: IRQ index 0 not found
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200110035524.23511-1-rayagonda.kokatanur@broadcom.com
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some gpio's parent irqdomain may not use the struct irq_fwspec as
argument, such as msi irqdomain. So rename the callback
populate_parent_fwspec() to populate_parent_alloc_arg() and make it
allocate and populate the specific struct which is needed by the
parent irqdomain.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-3-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 179e5a6114 ("pinctrl: intel: Remove default Interrupt Status
offset") removes default interrupt status offset of GPIO controllers,
with previous commits explicitly providing the previously default
offsets. However, the is_offset value in SPTH_COMMUNITY is missing,
preventing related irq from being properly detected and handled.
Fixes: f702e0b93c ("pinctrl: sunrisepoint: Provide Interrupt Status register offset")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745
Cc: stable@vger.kernel.org
Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- Split R-Car H3 support in two independent drivers,
- Miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXhZAzwAKCRCKwlD9ZEnx
cHpkAQCrz7kaC9rIRMO9eRZLV6sX6M+PeFw3DXKjm8N0qxG8hQD6AtKl5Gl/CAoq
RSO/0PpVIp97A904MJt+EOkX6eSBhwc=
=LEq1
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.5
- Split R-Car H3 support in two independent drivers,
- Miscellaneous fixes and cleanups.
Commit 179e5a6114 ("pinctrl: intel: Remove default Interrupt Status
offset") removes default interrupt status offset of GPIO controllers,
with previous commits explicitly providing the previously default
offsets. However, the is_offset value in SPTH_COMMUNITY is missing,
preventing related irq from being properly detected and handled.
Fixes: f702e0b93c ("pinctrl: sunrisepoint: Provide Interrupt Status register offset")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745
Cc: stable@vger.kernel.org
Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Despite using the same compatible values ("r8a7795"-based) because of
historical reasons, R-Car H3 ES1.x (R8A77950) and R-Car H3 ES2.0+
(R8A77951) are really different SoCs, with different part numbers, and
with different Pin Function Controller blocks.
Reflect this in the pinctrl configuration, by replacing the existing
CONFIG_PINCTRL_PFC_R8A7795 symbol by two new config symbols:
CONFIG_PINCTRL_PFC_R8A77950 and CONFIG_PINCTRL_PFC_R8A77951. The latter
are selected automatically, depending on the soon-to-be-introduced
corresponding SoC-specific config options, and on the current common
config option, to relax dependencies.
Rename the individual pin control driver source files from
pfc-r8a7795-es1.c to pfc-r8a77950.c, and from pfc-r8a7795.c to
pfc-r8a77951.c, and make them truly independent.
As both SoCs share the same compatible value, special care must be taken
to match them to the correct pin control driver, if support for it is
included in the running kernel.
This will allow making support for early R-Car H3 revisions optional,
the largest share of which is taken by the pin control driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191230083156.19191-1-geert+renesas@glider.be
Simplify the code of the driver's irq_set_type() function by doing some
factorization. The behaviour is unchanged.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200106232711.559727-5-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Until there is the need to handle the JZ4760B and X1000E differently
there is no reason to use a separate ingenic_chip_info since the data
it contains is the same than for the JZ4760 and X1000 respectively.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200106232711.559727-4-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of passing a numeric ID as match data, and retrieve a pointer to
the ingenic_chip_info structure in an ugly succession of if/else in the
probe function, get the pointer to the ingenic_chip_info structure
directly from the match data, and store the numeric ID inside the
ingenic_chip_info structure.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200106232711.559727-3-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We enforce devicetree support in the Kconfig and all Ingenic boards
without exception probe their drivers from devicetree. The code path to
probe the driver from arch code can then be considered as dead code and
removed.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200106232711.559727-2-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOH_5 and GPIOH_6 can have two Ethernet related functions:
- GPIOH_5 can be ETH_TXD1 or ETH_RXD3
- GPIOH_6 can be ETH_TXD0 or ETH_RXD2
Add the bits for eth_rxd3_h and eth_rxd2_h so the ETH_RXD function can
be disabled when using the ETH_TXD function of GPIOH_{5,6}. No problem
was observed so far, but in theory this could lead to two different
signals being routed to the same pad (which could break Ethernet).
These settings were found in the public "Amlogic Ethernet controller
user guide":
http://openlinux.amlogic.com/@api/deki/files/75/=Amlogic_Ethenet_controller_user_Guide.pdf
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20191226191425.3797490-1-martin.blumenstingl@googlemail.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The npcmgpio_irqchip structure is only copied into another
structure, so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1577864614-5543-17-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pm8xxx_pinctrl_desc structure is only copied into another
structure, so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1577864614-5543-15-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pm8xxx_pinctrl_desc structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1577864614-5543-9-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In meson_pinconf_get_drive_strength, variable bit is calculated by
meson_calc_reg_and_bit, this value is the offset from the first pin of a
certain bank to current pin, while Meson SoCs use two bits for each pin
to depict drive-strength. So a left shift by 1 should be done or node
pinconf-pins shows wrong message.
Fixes: 6ea3e3bbef ("pinctrl: meson: add support of drive-strength-microamp")
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In a rare randconfig build I came across one configuration that does
not enable CONFIG_GPIOLIB, which is needed by lochnagar:
ERROR: "devm_gpiochip_add_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_free" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_request" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_get_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
Add another 'select' like all other pinctrl drivers have.
Fixes: 0548448b71 ("pinctrl: lochnagar: Add support for the Cirrus Logic Lochnagar")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191218163701.171914-1-arnd@arndb.de
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The m_voc_groups is not declared outside of the
driver, so make it static to avoid the following
sparse wanrning:
drivers/pinctrl/qcom/pinctrl-msm8976.c:592:12: warning: symbol 'm_voc_groups' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191218102804.2487374-1-ben.dooks@codethink.co.uk
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_irq_count() is the more generic way (independent of
device trees) to determine the count of available interrupts. So
use this instead.
As platform_irq_count() might return an error code (which
of_irq_count doesn't) some additional handling is necessary.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1576672860-14420-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dsi entry is defined identically twice, so remove
the second one to remove the sparse warning:
drivers/pinctrl/actions/pinctrl-s700.c:1581:10: warning: Initializer entry defined twice
drivers/pinctrl/actions/pinctrl-s700.c:1586:10: also defined here
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191218102013.2465038-1-ben.dooks@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1.Add pinctrl drivers for the SPI flash controller (SFC) of
X1000 and X1500.
2.Add pinctrl driver for the synchronous serial interface (SSI)
of X1000.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/1576426864-35348-4-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1.Fix the pullup parameter of X1000.
2.X1000 and X1500 have only one set of uart1 hwflow pin mapping,
so modify "uart1_hwflow_d" to "uart1_hwflow".
3.X1000 has only one set of mmc1 pin mapping, so modify
"mmc1-1bit-e/mmc1-4bit-e" to "mmc1-1bit/mmc1-4bit".
4.X1000 has only one regular externel memory controller that
does not support nand flash, so change "nemc_" to "emc_".
5.X1500 has only one set of mmc, so modify "mmc0_" to "mmc_".
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/1576426864-35348-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.
A closer look reveals other issues:
- Some functionality is available on alternative pins, but the
PINMUX_DATA() entries is using the wrong marks,
- Several configurations are missing.
Fix this by:
- Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
corresponding enum IDs,
- Adding all missing enum IDs and marks,
- Use the right (*_PJ2x) variants for alternative pins,
- Adding all missing configurations to pinmux_data[],
- Adding all missing function GPIO definitions to pinmux_func_gpios[].
See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
[1] Table 1.4 List of Pins
[2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
(32 Mailboxes × 1 Channel),
[3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
One Channel (96 Mailboxes × 1 Channel),
[4] Table 48.3 Multiplexed Pins (Port B),
[5] Table 48.4 Multiplexed Pins (Port C),
[6] Table 48.10 Multiplexed Pins (Port J),
[7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.
Fix this by:
- Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
configures the combined "CTX0&CTX1" output signal,
- Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
the shared "CRX0/CRX1" input signal, which is fed to both CAN
inputs,
- Adding the missing function GPIO definition for "CTX0&CTX1" to
pinmux_func_gpios[],
- Moving all CAN enums next to each other.
See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
[1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
Version),
[2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
Version,
[3] Table 1.4 List of Pins,
[4] Figure 20.29 Connection Example when Using This Module as 1-Channel
Module (64 Mailboxes x 1 Channel),
[5] Table 32.10 Multiplexed Pins (Port J),
[6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).
Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
The FN_SDSELF_B and FN_SD1_CLK_B enum IDs are used twice, which means
one set of users must be wrong. Replace them by the correct enum IDs.
Fixes: 87f8c98863 ("sh-pfc: Add r8a7778 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-2-geert+renesas@glider.be
Currently only the drivers/pinctrl/devicetree.c code allows registering
pinctrl-mappings which may later be unregistered, all other mappings
are assumed to be permanent.
Non-dt platforms may also want to register pinctrl mappings from code which
is build as a module, which requires being able to unregister the mapping
when the module is unloaded to avoid dangling pointers.
To allow unregistering the mappings the devicetree code uses 2 internal
functions: pinctrl_register_map and pinctrl_unregister_map.
pinctrl_register_map allows the devicetree code to tell the core to
not memdup the mappings as it retains ownership of them and
pinctrl_unregister_map does the unregistering, note this only works
when the mappings where not memdupped.
The only code relying on the memdup/shallow-copy done by
pinctrl_register_mappings is arch/arm/mach-u300/core.c this commit
replaces the __initdata with const, so that the shallow-copy is no
longer necessary.
After that we can get rid of the internal pinctrl_unregister_map function
and just use pinctrl_register_mappings directly everywhere.
This commit also renames pinctrl_unregister_map to
pinctrl_unregister_mappings so that its naming matches its
pinctrl_register_mappings counter-part and exports it.
Together these 2 changes will allow non-dt platform code to
register pinctrl-mappings from modules without breaking things on
module unload (as they can now unregister the mapping on unload).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191216205122.1850923-2-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since this message is printed for each port, it creates a lot of output
during boot and would serve better only during debugging.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191212135301.17915-1-chris.brandt@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car Gen3 Hardware Manual Errata for Rev. 2.00 of October 24, 2019
changed the configuration bits for drive and bias control for the
DU_DOTCLKIN3 pin on R-Car M3-N, to match the same pin on R-Car H3.
Update the driver to reflect this.
After this, the handling of drive and bias control for the various
DU_DOTCLKINx pins is consistent across all of the R-Car H3, M3-W,
M3-W+, and M3-N SoCs.
Fixes: 86c045c2e4 ("pinctrl: sh-pfc: r8a77965: Replace DU_DOTCLKIN2 by DU_DOTCLKIN3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191113101653.28428-1-geert+renesas@glider.be
JZ4760 support was added in parallel of the previous patch so this one
slipped through. The first SoC to use the new register is the JZ4760 and
not the JZ4770, fix it here.
Fixes: 7009d046a6 ("pinctrl: ingenic: Handle PIN_CONFIG_OUTPUT config")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20191210164446.53912-1-paul@crapouillou.net
[Folded into OF dependency]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rather than always using handle_simple_irq() as the gpio_irq_chip
handler, set a more appropriate handler based on the IRQ trigger type
requested.
This is important for level triggered interrupts which need to be
masked during handling.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191215210503.15488-2-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
on sc7180 we have cases where multiple functions from the same
qup instance share the same pin. This is true for qup02/04/11 and qup13.
Add new function names to distinguish which qup function to use.
The device tree files for this platform haven't landed in mainline yet,
so there aren't any users upstream who should break with this change
in function names, however, anyone using the devicetree files that were
posted on the lists and using these specific function names will need
to update their changes.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ef36a9118-f2919277-effa-4cd5-adf8-bbc8016f31df-000000@us-west-2.amazonses.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs that can be configured as wakeup sources, have their
interrupt lines routed to PDC interrupt controller.
Provide the interrupt map of the GPIO to its wakeup capable
interrupt parent.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1572419178-5750-2-git-send-email-mkshah@codeaurora.org
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All Samsung pinctrl drivers select common part - PINCTRL_SAMSUNG which uses
both OF and GPIOLIB inside. However only Exynos drivers depend on these,
therefore after enabling COMPILE_TEST, on x86_64 build of S3C64xx driver
failed:
drivers/pinctrl/samsung/pinctrl-samsung.c: In function ‘samsung_gpiolib_register’:
drivers/pinctrl/samsung/pinctrl-samsung.c:969:5: error: ‘struct gpio_chip’ has no member named ‘of_node’
gc->of_node = bank->of_node;
^
Rework the dependencies so all Samsung drivers and common
PINCTRL_SAMSUNG part depend on OF_GPIO (which is default yes if GPIOLIB
and OF are enabled).
Reported-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reflect in the driver that it is now a pin control one.
While here, update copyright years and authors.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When all preparations are done, we may switch to pin control API.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The introduced callback ->pin_dbg_show() is useful for debugging.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add implementation for:
- pin control, group information retrieval: count, name and pins
- pin muxing:
- function information (count, name and groups)
- mux setting
- GPIO control (enable, disable, set direction)
- pin configuration:
- pull disable, up and down
- any other option is treated as not supported.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We may use now available struct intel_pinctrl in the driver.
No functional change implied.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to implement pin control for Intel Lynxpoint, we need
data structures in which to store and pass along pin, community
and SoC data information.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Allows querying GPIO direction from the pad config register.
If the pad is not in GPIO mode, return an error.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of playing tricks with registers in the interrupt handler,
utilize the IRQ chip core for ACKing interrupts properly.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is nothing wrong with requesting pin that owned by ACPI.
The only difference is how interrupt status will be reflected.
It means that in ACPI mode we may not use pin as GPIO-backed IRQ.
Taking above into consideration, move the check from GPIO to IRQ chip
callback.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Consolidate IRQ routines for better maintenance.
While here, rename lp_irq_type() to lp_irq_set_type() to be in align
with a callback name.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Consolidate ->remove and ->probe() callbacks for better maintenance.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We may need this function for other features in the pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Simple type conversion with no functional change implied.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Convert driver to use memory mapped IO accessors.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to keep pointer to struct platform_device, which is container
of struct device, because the latter is what have been used everywhere outside
of ->probe() path. In any case we may derive pointer to the container when
needed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
A pin in native mode still can be requested as GPIO, though we assume
that firmware has configured it properly, which sometimes is not the case.
Here we allow turning the pin as GPIO to avoid potential issues,
but issue warning that something might be wrong.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
New generations can use 2 bits for mode selector.
Update the code to support it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The pattern
foo = kmalloc(sizeof(*foo), GFP_KERNEL);
has an advantage when foo type is changed. Since we are planning a such,
better to be prepared by using standard pattern for memory allocation.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Replace explicit casting by pointer to struct resource with
specifier replacement to %pR to print the IO resource.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to assign ret variable in ->probe().
Drop useless assignment.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When we count from 0 it's possible to get into off-by-one error.
That's what had happened to this driver. So, correct amount of pins
and related typos in the code.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The Intel Lynxpoint pinctrl driver implements irqchip callbacks which are
called with desc->lock raw_spinlock held. In mainline this is fine because
spinlock resolves to raw_spinlock. However, running the same code in -rt
we will get a BUG() asserted.
This is because in -rt spinlocks are preemptible so taking the driver
private spinlock in irqchip callbacks causes might_sleep() to trigger.
In order to keep -rt happy but at the same time make sure that register
accesses get serialized, convert the driver to use raw_spinlock instead.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move Lynxpoint GPIO driver under Intel pin control umbrella
for further transformation to a real pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We may use now available struct intel_pinctrl in the driver.
No functional change implied.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use local variable to keep device pointer in order to increase readability
of the driver.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to keep pointer to struct platform_device, which is container
of struct device, because the latter is what have been used everywhere outside
of ->probe() path. In any case we may derive pointer to the container when
needed.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There are few drivers for Intel SoC GPIO which may utilize
the same data structure to describe this IP.
Share struct intel_pinctrl for wider user.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is a logical continuation of the commit 5fbe5b5883 ("gpio: Initialize
the irqchip valid_mask with a callback") to split IRQ initialization to
hardware and valid mask setup parts.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It has turned out that some mmc host drivers, but perhaps also others
drivers, needs to reset the pinctrl into the default state
(PINCTRL_STATE_DEFAULT). However, they can't use the existing
pinctrl_pm_select_default_state(), as that requires CONFIG_PM to be set.
This leads to open coding, as they need to look up the default state
themselves and then select it.
To avoid the open coding, let's introduce pinctrl_select_default_state()
and make it available independently of CONFIG_PM. As a matter of fact, this
makes it more consistent with the behaviour of the driver core, as it
already tries to looks up the default state during probe.
Going forward, users of pinctrl_pm_select_default_state() are encouraged to
move to pinctrl_select_default_state(), so the old API can be removed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-2-ulf.hansson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix below linker error
ld: drivers/pinctrl/pinctrl-equilibrium.o: in function
`pinconf_generic_dt_node_to_map_all':
pinctrl-equilibrium.c:(.text+0xb): undefined reference
to `pinconf_generic_dt_node_to_map'
Caused by below commit
1948d5c51d ("pinctrl: Add pinmux & GPIO controller driver for a new SoC")
by adding 'depends on OF' in Kconfig driver entry.
Reported-by: Randy Dunlap <rdunlap@infradead.org>>
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Link: https://lore.kernel.org/r/ba937f271d1a2173828a2325990d62cb36d61595.1575514110.git.rahul.tanwar@linux.intel.com
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Fix Baytrail silicon issue by using a global lock
* Fix North community pin names that user will assume their functions
* Convert Cherryview and Baytrail to pass IRQ chip along with GPIO one
The following is an automated git shortlog grouped by driver:
baytrail:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Update North Community pin list
- Really serialize all register accesses
cherryview:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Split out irq hw-init into a separate helper function
-----BEGIN PGP SIGNATURE-----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=EWpg
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.5-2
* Fix Baytrail silicon issue by using a global lock
* Fix North community pin names that user will assume their functions
* Convert Cherryview and Baytrail to pass IRQ chip along with GPIO one
The following is an automated git shortlog grouped by driver:
baytrail:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Update North Community pin list
- Really serialize all register accesses
cherryview:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Split out irq hw-init into a separate helper function
This commit adds a check on ops pointer to avoid a kernel panic when
ops->strict is used. Indeed, on some pinctrl driver (at least for
pinctrl-stmfx) the pinmux ops is not implemented. Let's assume than gpio
can be used in this case.
Fixes: 472a61e777 ("pinctrl/gpio: Take MUX usage into account")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20191204144106.10876-1-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2600 pinconf is a little different from previous generations of
ASPEED BMC SoCs in terms of architecture. The pull-down setting is
per-pin setting now, and drive-strength support 4 kind of value (e.g.
4ma, 8ma, 12ma, 16ma).
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Trim unused pinctrl register macros]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202061432.3996-8-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since some of the AST2600 pinconf setting are not just single bit, modified
aspeed_pin_config @bit to @mask and add @mask to aspeed_pin_config_map to
support configuring multiple bits.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202061432.3996-7-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2600 pinconf differs from the 2400 and 2500, aspeed_pin_config_map
should define separately, and add @confmaps and @nconfmaps to
aspeed_pinctrl_data structure for that change.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202061432.3996-6-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This helper macro is for declaring single bit (SB) mask pinconf,
and is used to prepare for modifying aspeed_pin_config
structure, the aspeed_pin_config structure @bit variable will be
modified to @mask.
This case is common in the AST2400/AST2500 which the mask is a single bit.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202061432.3996-5-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
John Stultz