MT7688 has several uarts that can be used for console. There are several
boards in the wild, that use ttyS1 or ttyS2. This patch applies a simply
autodetection routine to figure out which ttyS the bootloader used as
console. The uarts come up in 6 bit mode by default. The bootloader will
have set 8 bit mode on the console. Find that 8bit tty and use it.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11459/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the USB HCD is running and the cpu is scaled too low, then the USB
stops working. Increase the idle speed of the core to fix this if the
kernel is built with USB support.
The "magic" values are taken from the Ralink SDK Kernel.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11441/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
request_mem_region() returns a pointer and not an integer with an error
value. A check for "< 0" on a pointer will cause problems, replace it
with not null checks instead. This was found with sparse.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11395/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds the PUM bits for USB and SDIO devices
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11387/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the SoC starts up most of the devices should be deactivated by the
PMU, they should be activated when they get used by their drivers. Some
devices should not get deactivate at startup like the serial, register
them in a special way.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11386/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This add detection of some clocks on the ar10 and grx390.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11385/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds support for setting the PMU register on the AR10 and GRX390.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11382/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PMU register are accessed in a non atomic way and they could be
accessed by different threads simultaneously, which could cause
problems this patch adds locking around the PMU registers. In
addition we now also wait till the PMU is actually deactivated.
[ralf@linux-mips.org: Fix spelling mistake in commit message as noticed
by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>.]
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11381/
Patchwork: https://patchwork.linux-mips.org/patch/11396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This drops another symbol dependency between setup.c and sprom.c which
will allow us to make SPROM code a separated module (and share it with
ARM).
Patch tested on Linksys WRT300N V1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11360/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are still few left:
1) Most of them about lines over 80 chars (increased readability exception)
2) Wrong parsing of preprocessor macros
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/11356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To support (extract) SPROM on Broadcom ARM devices we should separate
SPROM code and make it a separated module. We won't want to export
bcm47xx_fill_sprom symbol so we should support SoC SPROM in the standard
fallback function and then modify ssb to use it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: <stable@vger.kernel.org> # 4.1+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11358/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
for_each_child_of_node performs an of_node_get on each iteration, so no
of_node_get is needed on breaking out of the loop when the device_node
structure is saved in another variable.
A simplified semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root;
local idexpression child;
@@
for_each_child_of_node(root, child) {
...
* of_node_get(child)
...
break;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Patchwork: https://patchwork.linux-mips.org/patch/11357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add user-mode implementations of gettimeofday() and clock_gettime() to
the VDSO. This is currently usable with 2 clocksources: the CP0 count
register, which is accessible to user-mode via RDHWR on R2 and later
cores, or the MIPS Global Interrupt Controller (GIC) timer, which
provides a "user-mode visible" section containing a mirror of its
counter registers. This section must be mapped into user memory, which
is done below the VDSO data page.
When a supported clocksource is not in use, the VDSO functions will
return -ENOSYS, which causes libc to fall back on the standard syscall
path.
When support for neither of these clocksources is compiled into the
kernel at all, the VDSO still provides clock_gettime(), as the coarse
realtime/monotonic clocks can still be implemented. However,
gettimeofday() is not provided in this case as nothing can be done
without a suitable clocksource. This causes the symbol lookup to fail
in libc and it will then always use the standard syscall path.
This patch includes a workaround for a bug in QEMU which results in
RDHWR on the CP0 count register always returning a constant (incorrect)
value. A fix for this has been submitted, and the workaround can be
removed after the fix has been in stable releases for a reasonable
amount of time.
A simple performance test which calls gettimeofday() 1000 times in a
loop and calculates the average execution time gives the following
results on a Malta + I6400 (running at 20MHz):
- Syscall: ~31000 ns
- VDSO (GIC): ~15000 ns
- VDSO (CP0): ~9500 ns
[markos.chandras@imgtec.com:
- Minor code re-arrangements in order for mappings to be made
in the order they appear to the process' address space.
- Move do_{monotonic, realtime} outside of the MIPS_CLOCK_VSYSCALL ifdef
- Use gic_get_usm_range so we can do the GIC mapping in the
arch/mips/kernel/vdso instead of the GIC irqchip driver]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add an initial implementation of a proper (i.e. an ELF shared library)
VDSO. With this commit it does not export any symbols, it only replaces
the current signal return trampoline page. A later commit will add user
implementations of gettimeofday()/clock_gettime().
To support both new toolchains and old ones which don't generate ABI
flags section, we define its content manually and then use a tool
(genvdso) to patch up the section to have the correct name and type.
genvdso also extracts symbol offsets ({,rt_}sigreturn) needed by the
kernel, and generates a C file containing a "struct mips_vdso_image"
containing both the VDSO data and these offsets. This C file is
compiled into the kernel.
On 64-bit kernels we require a different VDSO for each supported ABI,
so we may build up to 3 different VDSOs. The VDSO to use is selected by
the mips_abi structure.
A kernel/user shared data page is created and mapped below the VDSO
image. This is currently empty, but will be used by the user time
function implementations which are added later.
[markos.chandras@imgtec.com:
- Add more comments
- Move abi detection in genvdso.h since it's the get_symbol function
that needs it.
- Add an R6 specific way to calculate the base address of VDSO in order
to avoid the branch instruction which affects performance.
- Do not patch .gnu.attributes since it's not needed for dynamic linking.
- Simplify Makefile a little bit.
- checkpatch fixes
- Restrict VDSO support for binutils < 2.25 for pre-R6
- Include atomic64.h for O32 variant on MIPS64]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts mpc30x_defconfig to use libata PATA
drivers.
PS This platform still uses "ide0=base[,ctl[,irq]]" hack in
its defconfig. The hack itself has been removed in 2008 and
this platform should be converted to using PATA platform host
driver (pata_platform) instead.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts maltaup_xpa_defconfig to use libata PATA
drivers (tc86c001 IDE host driver has no corresponding libata
driver yet so it is not converted).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11140/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts maltaup_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11142/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts maltasmvp_eva_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11139/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts maltaaprp_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: b.zolnierkie@samsung.com
Patchwork: https://patchwork.linux-mips.org/patch/11137/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts malta_qemu_32r6_defconfig to use libata
PATA drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: b.zolnierkie@samsung.com
Patchwork: https://patchwork.linux-mips.org/patch/11138/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts malta_kvm_guest_defconfig to use libata
PATA drivers (tc86c001 IDE host driver has no corresponding
libata driver yet so it is not converted).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11136/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts malta_kvm_defconfig to use libata PATA
drivers (tc86c001 IDE host driver has no corresponding libata
driver yet so it is not converted).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts malta_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11134/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts lemote2f_defconfig to use libata PATA
drivers.
PS This platform uses CS5536 chipset which (due to historical
reasons) has basic support in AMD/nVidia PATA host driver and
full support in a newer CS5536 PATA one (pata_cs5536). Thus
most likely this platform should switch to using the latter
host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts lasat_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Brian Murphy <brian@murphy.dk>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts fuloong2e_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11131/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts e55_defconfig to use libata PATA drivers.
PS This platform still uses "ide0=base[,ctl[,irq]]" hack in
its defconfig. The hack itself has been removed in 2008 and
this platform should be converted to using PATA platform host
driver (pata_platform) instead.
Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts capcella_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11129/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts bigsur_defconfig to use libata PATA
drivers (tc86c001 IDE host driver has no corresponding libata
driver yet so it is not converted).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11128/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Extend the existing support for Hardware Table Walking (HTW) to MIPS64
systems by supporting PMDs & setting the pointer size bit in PWSize,
then ceasing to blacklist HTW on MIPS64 systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11224/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we fail to register any real SMP implementations, fall back to
registering the dummy UP implementation. Otherwise when we build an SMP
kernel & run it on a system where the SMP implementations fail to probe
(eg. QEMU) the kernel will perform a NULL dereference attempting to call
mp_ops->smp_setup() from plat_smp_setup().
Notably this fixes booting kernels with CPS SMP enabled on QEMU, which
doesn't currently implement the CM, CPC or GIC.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11223/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move memory configuration to be performed via device tree for the Malta
board. This moves more Malta specific code to malta-dtshim.c, leaving
the rest of the mti-malta code a little more board-agnostic. This will
be useful to share more code between boards, with the device tree
providing the board specifics as intended.
Since we can't rely upon Malta boards running a bootloader capable of
handling devictrees & filling in the required information, a piece of
shim code (malta_dt_shim) is added to consume the (e)memsize variables
provided as part of the bootloader environment (or on the kernel command
line) then generate the DT memory node using the provided values.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Patchwork: https://patchwork.linux-mips.org/patch/11222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The fw_getmdesc function & fw_memblock_t abstraction is only used by
Malta, and so far as I can tell serves no purpose beyond making the code
less clear than it could be. Remove the useless level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11221/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit a68d09a156 ("MIPS: Don't use RI/XI with 32-bit kernels on
64-bit CPUs") prevented use of RIXI on MIPS64 systems, stating that the
"TLB handlers cannot handle this case". What they actually couldn't
handle was cases where there were less fill bits in the Entry{Lo,Hi}
registers than bits used by software in PTEs. The handlers can now deal
with this case, so enable RIXI for MIPS32 kernels on MIPS64 systems.
Note that beyond the obvious benefits provided by having RIXI on such
systems, this is required for systems implementing MIPSr6 where RIXI
cannot be disabled.
This reverts commit a68d09a156 ("MIPS: Don't use RI/XI with 32-bit
kernels on 64-bit CPUs").
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11219/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 748e787eb6 ("MIPS: Optimize TLB refill for RI/XI
configurations.") stopped explicitly clearing the bits used by software
in PTEs by making use of a rotate instruction that rotates them into the
fill bits of the Entry{Lo,Hi} register. This can only work if there are
actually enough fill bits in the register to cover the software
maintained bits, otherwise we end up writing those bits into the upper
bits of the PFN or PFNX field of the Entry{Lo,Hi} register.
Fix this by detecting the number of fill bits present in the
Entry{Lo,Hi} registers & explicitly clearing the software bits where
necessary.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11218/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tidy up the definition of the EntryLo RI & XI bits using BITS_PER_LONG
rather than #ifdef'ing on CONFIG_64BIT, and add a definition for the
offset to the PFN field for use by a later patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code in build_update_entries for 64 bit physical addresses on a
MIPS64 CPU and 32 bit physical addresses on a MIPS32 CPU is now
identical, with the exception of r4k bug workaround in the latter which
would simply not apply to the former. Remove the duplication and some
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cpu_has_rixi cases in build_update_entries are now identical to the
non-RIXI cases with the one exception of the r45k_bvahwbug case which is
hardcoded as never happening anyway & presumably was either missed from
the RIXI path or would never happen on a CPU with RIXI support. Remove
the redundant checks & duplication.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11215/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of build_convert_pte_to_entrylo in the RIXI cases within
build_update_entries rather than open-coding it 4 times.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11214/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Prior to release 6 of the MIPS architecture it has been implementation
dependent whether masked interrupts cause a wait instruction to return,
so the kernel has effectively had to maintain a whitelist of cores upon
which it is safe to use the r4k_wait_irqoff cpu_wait implementation.
With MIPSr6 this is no longer implementation dependent and
r4k_wait_irqoff can always be used.
Remove the existing I6400 case which will no longer ever be hit, and was
incorrect anyway since I6400 & r6 in general doesn't have the WII bit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11210/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ensure the update to which core the core-other GCR regions reflect has
taken place before any core-other GCRs are accessed by placing a memory
barrier (sync instruction) between the write to the core-other registers
and any such GCR accesses.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11209/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Document that CPC core-other accesses must take place within the bounds
of the CM lock, and begin using the CM lock functions where we access
the GCRs of other cores. This is required because with CM3 the CPC began
using GCR_CL_OTHER instead of CPC_CL_OTHER.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-kernel@vger.kernel.org
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11208/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce mips_cm_lock_other & mips_cm_unlock_other, mirroring the
existing CPC equivalents, in order to lock access from the current core
to another via the core-other GCR region. This hasn't been required in
the past but with CM3 the CPC starts using GCR_CL_OTHER rather than
CPC_CL_OTHER and this will be required for safety.
[ralf@linux-mips.org: Fix merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11207/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PVPE (or PVP in >= CM3) field is 10 bits wide, but the mask
previously only covered the bottom 9 bits. Extend the mask to cover all
10 bits of the field.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11206/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging core bringup it is useful to see the state of the CPC
sequencer, so output that value if the core hasn't started within a
reasonable amount of time (1 second). This avoids simply appearing to
the user to hang if a secondary core fails to start.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11205/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Config1 register is architecturally defined as required, and is thus
present in all systems which may make use of cps-vec.S. Skip the check
for its presence via the Config.M bit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11204/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than patching the start of mips_cps_core_entry to provide the
base address of the CM GCRs, simply read that base address from the cop0
CMGCRBase register, converting from the physical address to an uncached
virtual address.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11203/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Provide support for outputting early debug information, in the form of
various register values should an exception occur, during the early
bringup of secondary cores. This code requires an ns16550-compatible
UART accessible from the secondary core, and is written in assembly due
to the environment in which such early exceptions occur where way may
not have a stack, be coherent or even have initialised caches.
[ralf@linux-mips.org: Fix merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11202/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the definition in locore.S and move a few of the other similar
definitions in asm/mipsregs.h too. CP0_INTCTL, CP0_SRSCTL, & CP0_SRSMAP
are unused so they're just dropped instead. CP0_DDATA_LO is left where
it is as I have patches to eliminate its use in locore.S and it
otherwise is unlikely to need to be used from assembly code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull block IO poll support from Jens Axboe:
"Various groups have been doing experimentation around IO polling for
(really) fast devices. The code has been reviewed and has been
sitting on the side for a few releases, but this is now good enough
for coordinated benchmarking and further experimentation.
Currently O_DIRECT sync read/write are supported. A framework is in
the works that allows scalable stats tracking so we can auto-tune
this. And we'll add libaio support as well soon. Fow now, it's an
opt-in feature for test purposes"
* 'for-4.4/io-poll' of git://git.kernel.dk/linux-block:
direct-io: be sure to assign dio->bio_bdev for both paths
directio: add block polling support
NVMe: add blk polling support
block: add block polling support
blk-mq: return tag/queue combo in the make_request_fn handlers
block: change ->make_request_fn() and users to return a queue cookie
Pull UML updates from Richard Weinberger:
- a new hrtimer based clocksource by Anton Ivanov
- ptrace() enhancments by Richard Weinberger
- random cleanups and bug fixes all over the place
* 'for-linus-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Switch clocksource to hrtimers
um: net: replace GFP_KERNEL with GFP_ATOMIC when spinlock is held
um: Report host OOM more nicely
um: Simplify STUB_DATA loading
um: Remove dead symbol from i386 syscall stub
um: Remove dead code from x86_64 syscall stub
um: Get rid of open coded NR_SYSCALLS
um: Store syscall number after syscall_trace_enter()
um: Define PTRACE_OLDSETOPTIONS
A fix for 4KiB stacks with SMP, and a change of maintenance status to
"Odd Fixes".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=I+wL
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag arch updates from James Hogan:
"A fix for 4KiB stacks with SMP, and a change of maintenance status to
'Odd Fixes'"
* tag 'metag-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
MAINTAINERS: Change Meta arch port status to Odd Fixes
metag: Turn irq_ctx_* macros into static inlines
metag: SMP: Fix 4KiB stack setup on secondary CPUs
Defconfig updates are kept separate from other branches mostly to avoid
conflicts between the different categories (driver branch enabling something
that has context conflict with SoC options, etc).
A lot of this again is scattered across the various hardware platforms.
multi_v7_defconfig, our "generic" config for most 32-bit platforms has
been gone through by Marvell Berlin maintainers and added most options
they need to run on their hardware. Broadcom NSP is also added there,
and the new Atmel SAMA5D2 (added last release). Rockchip also has display
and other devices supported in that config.
In addition to that, the usual small churn of new options being added
here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KsDh
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"Defconfig updates are kept separate from other branches mostly to
avoid conflicts between the different categories (driver branch
enabling something that has context conflict with SoC options, etc).
A lot of this again is scattered across the various hardware
platforms. multi_v7_defconfig, our "generic" config for most 32-bit
platforms has been gone through by Marvell Berlin maintainers and
added most options they need to run on their hardware. Broadcom NSP
is also added there, and the new Atmel SAMA5D2 (added last release).
Rockchip also has display and other devices supported in that config.
In addition to that, the usual small churn of new options being added
here and there"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: multi_v7_defconfig: enable UniPhier I2C drivers
ARM: multi_v7_defconfig: Enable rtl8152 ethernet driver for Odroid-XU4
ARM: exynos_defconfig: Enable rtl8152 ethernet driver for Odroid-XU4
ARM: exynos_defconfig: Enable WiFi-Ex as a module instead built-in
ARM: exynos_defconfig: Disable simplefb support
ARM: exynos_defconfig: Enable LEDS for Odroid-XU3/XU4
ARM: multi_v7_defconfig: Enable DWC2 USB driver and USB ethernet gadget
ARM: exynos_defconfig: Enable DWC2 USB driver and USB ethernet gadget
ARM: exynos_defconfig: Enable USB Video Class support
ARM: multi_v7_defconfig: improve multi_v7_defconfig support for Berlin
ARM: tegra: Update multi_v7_defconfig
ARM: multi_v7_defconfig: Add Atmel SDHCI device
ARM: multi_v7_defconfig: Add Atmel Flexcom device
ARM: multi_v7_defconfig: Add Atmel SAMA5D2 SoC
ARM: at91/defconfig: add sama5d2 and its new devices to sama5 defconfig
ARM: at91/defconfig: update at91_dt defconfig
ARM: at91/defconfig: update sama5 defconfig
ARM: configs: Enable FIXED_PHY in multi_v7 defconfig
ARM: configs: update lpc18xx defconfig
ARM: socfpga_defconfig: enable fpga manager
...
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
New and/or improved SoC support for this release:
- Marvell Berlin:
* Enable standard DT-based cpufreq
* Add CPU hotplug support
- Freescale:
* Ethernet init for i.MX7D
* Suspend/resume support for i.MX6UL
- Allwinner:
* Support for R8 chipset (used on NTC's $9 C.H.I.P board)
- Mediatek:
* SMP support for some platforms
- Uniphier:
* L2 support
* Cleaned up SMP support, etc.
+ A handful of other patches around above functionality, and a few other
smaller changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=h5xk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New and/or improved SoC support for this release:
Marvell Berlin:
- Enable standard DT-based cpufreq
- Add CPU hotplug support
Freescale:
- Ethernet init for i.MX7D
- Suspend/resume support for i.MX6UL
Allwinner:
- Support for R8 chipset (used on NTC's $9 C.H.I.P board)
Mediatek:
- SMP support for some platforms
Uniphier:
- L2 support
- Cleaned up SMP support, etc.
plus a handful of other patches around above functionality, and a few
other smaller changes"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM: uniphier: rework SMP operations to use trampoline code
ARM: uniphier: add outer cache support
Documentation: EXYNOS: Update bootloader interface on exynos542x
ARM: mvebu: add broken-idle option
ARM: orion5x: use mac_pton() helper
ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
ARM: sunxi: Add R8 support
ARM: digicolor: select pinctrl/gpio driver
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
ARM: S3C64XX: Use PWM lookup table for mach-smartq
ARM: S3C64XX: Use PWM lookup table for mach-hmt
ARM: S3C64XX: Use PWM lookup table for mach-crag6410
ARM: S3C64XX: Use PWM lookup table for smdk6410
...
Again we have a sizable (but not huge) cleanup branch with a net delta of about
-3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now gone
completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the above are
the major pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uI7R
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
A handful of fixes that came in and didn't seem warranted to go in through
the 4.3-rc cycle.
- MAINTAINERS updates for one of the Broadcom platforms and lpc18xx
- A couple of non-critical Davinci bugfixes
- A fix to reset irq affinity for TI platforms (silences a warning at reboot)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iRbU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Olof Johansson:
"A handful of fixes that came in and didn't seem warranted to go in
through the 4.3-rc cycle.
- MAINTAINERS updates for one of the Broadcom platforms and lpc18xx
- A couple of non-critical Davinci bugfixes
- A fix to reset irq affinity for TI platforms (silences a warning at
reboot)"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update lpc18xx entry with more drivers
soc: ti: reset irq affinity before freeing irq
ARM: cns3xxx: pci: avoid potential stack overflow
ARM: davinci: clock: Correct return values for API functions
ARM: davinci: re-use %*ph specifier
MAINTAINERS: add entry for the Broadcom Northstar Plus SoCs
1/ Add support for the ACPI 6.0 NFIT hot add mechanism to process
updates of the NFIT at runtime.
2/ Teach the coredump implementation how to filter out DAX mappings.
3/ Introduce NUMA hints for allocations made by the pmem driver, and as
a side effect all devm allocations now hint their NUMA node by
default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a2/L
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"Outside of the new ACPI-NFIT hot-add support this pull request is more
notable for what it does not contain, than what it does. There were a
handful of development topics this cycle, dax get_user_pages, dax
fsync, and raw block dax, that need more more iteration and will wait
for 4.5.
The patches to make devm and the pmem driver NUMA aware have been in
-next for several weeks. The hot-add support has not, but is
contained to the NFIT driver and is passing unit tests. The coredump
support is straightforward and was looked over by Jeff. All of it has
received a 0day build success notification across 107 configs.
Summary:
- Add support for the ACPI 6.0 NFIT hot add mechanism to process
updates of the NFIT at runtime.
- Teach the coredump implementation how to filter out DAX mappings.
- Introduce NUMA hints for allocations made by the pmem driver, and
as a side effect all devm allocations now hint their NUMA node by
default"
* tag 'libnvdimm-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
coredump: add DAX filtering for FDPIC ELF coredumps
coredump: add DAX filtering for ELF coredumps
acpi: nfit: Add support for hot-add
nfit: in acpi_nfit_init, break on a 0-length table
pmem, memremap: convert to numa aware allocations
devm_memremap_pages: use numa_mem_id
devm: make allocations numa aware by default
devm_memremap: convert to return ERR_PTR
devm_memunmap: use devres_release()
pmem: kill memremap_pmem()
x86, mm: quiet arch_add_memory()
This time we have a very typical update which is mostly fixes and updates to
drivers and no new drivers.
- Biggest change is coming from Peter for edma cleanup which even caused
some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWP1vYAAoJEHwUBw8lI4NHKg8QAKwJ/iPxZDMfWwCLAoZoeaDp
GgOmxIZ3LWrFQHIziI1IUcxSAU28Z+N6GBziaXycw49oQic4J/ukHGhgxwI2GM/W
JGbFzHalnwdGqKzVZyfWGV0njT3KRvwKl7qqb66ZhikF5lD5imga66QGGxof8wBK
uoXra7yycrE8nGpyY5Gdd4H59aWVyAK1fW6+0cxa2kMfWo8vLkgj/olbzYZydhQz
DFCEvx2hbTyP/8VjGybVhtd+oeLjX43tGJOm6weyCb/8z3/soD73CChZIP53Mt6i
g+LKPfurRZ3VGILgdemkiMB+5pXi4jhmziw5pCSI6BluUGVZAMyg8hC1zapFUr/2
HaLfVmtxYdsBlceuMss1f3vyN2d+kRdDPKlOb9Td0PC2TEpSa5QayuMscvVfau+Q
epSdIxgjlHqAVDVZJ0kX55FLdmItx36tat6zJL5cUcZmrDvEY3TQmvcXyR2dIltY
U9WB2lRaETOG4Js0gAItXDjijNvLs0F4q10Zk6RdH4BcWbuqvONAhaCpWKeOWNsf
NgQkkg+DqHqol6+C0pI0uX6dvEfwJuZ4bqq98wl4SryuxWJNra/g55/oFEFDbJCU
oRMPYguMUgV8tzCpAurmDhxcrsZu/dvaSSW+flVz2QP81ecvFjRnZ8hhXbCr6iWi
VVoAISmQBQPCXoqPr7ZC
=tIzO
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
Pull drm updates from Dave Airlie:
"I Was Almost Tempted To Capitalise Every Word, but then I decided I
couldn't read it myself!
I've also got one pull request for the sti driver outstanding. It
relied on a commit in Greg's tree and I didn't find out in time, that
commit is in your tree now so I might send that along once this is
merged.
I also had the accidental misfortune to have access to a Skylake on my
desk for a few days, and I've had to encourage Intel to try harder,
which seems to be happening now.
Here is the main drm-next pull request for 4.4.
Highlights:
New driver:
vc4 driver for the Rasberry Pi VPU.
(From Eric Anholt at Broadcom.)
Core:
Atomic fbdev support
Atomic helpers for runtime pm
dp/aux i2c STATUS_UPDATE handling
struct_mutex usage cleanups.
Generic of probing support.
Documentation:
Kerneldoc for VGA switcheroo code.
Rename to gpu instead of drm to reflect scope.
i915:
Skylake GuC firmware fixes
HPD A support
VBT backlight fallbacks
Fastboot by default for some systems
FBC work
BXT/SKL workarounds
Skylake deeper sleep state fixes
amdgpu:
Enable GPU scheduler by default
New atombios opcodes
GPUVM debugging options
Stoney support.
Fencing cleanups.
radeon:
More efficient CS checking
nouveau:
gk20a instance memory handling improvements.
Improved PGOB detection and GK107 support
Kepler GDDR5 PLL statbility improvement
G8x/GT2xx reclock improvements
new userspace API compatiblity fixes.
virtio-gpu:
Add 3D support - qemu 2.5 has it merged for it's gtk backend.
msm:
Initial msm88896 (snapdragon 8200)
exynos:
HDMI cleanups
Enable mixer driver byt default
Add DECON-TV support
vmwgfx:
Move to using memremap + fixes.
rcar-du:
Add support for R8A7793/4 DU
armada:
Remove support for non-component mode
Improved plane handling
Power savings while in DPMS off.
tda998x:
Remove unused slave encoder support
Use more HDMI helpers
Fix EDID read handling
dwhdmi:
Interlace video mode support for ipu-v3/dw_hdmi
Hotplug state fixes
Audio driver integration
imx:
More color formats support.
tegra:
Minor fixes/improvements"
[ Merge fixup: remove unused variable 'dev' that had all uses removed in
commit 4e270f088011: "drm/gem: Drop struct_mutex requirement from
drm_gem_mmap_obj" ]
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (764 commits)
drm/vmwgfx: Relax irq locking somewhat
drm/vmwgfx: Properly flush cursor updates and page-flips
drm/i915/skl: disable display side power well support for now
drm/i915: Extend DSL readout fix to BDW and SKL.
drm/i915: Do graphics device reset under forcewake
drm/i915: Skip fence installation for objects with rotated views (v4)
vga_switcheroo: Drop client power state VGA_SWITCHEROO_INIT
drm/amdgpu: group together common fence implementation
drm/amdgpu: remove AMDGPU_FENCE_OWNER_MOVE
drm/amdgpu: remove now unused fence functions
drm/amdgpu: fix fence fallback check
drm/amdgpu: fix stoping the scheduler timeout
drm/amdgpu: cleanup on error in amdgpu_cs_ioctl()
drm/i915: Fix locking around GuC firmware load
drm/amdgpu: update Fiji's Golden setting
drm/amdgpu: update Fiji's rev id
drm/amdgpu: extract common code in vi_common_early_init
drm/amd/scheduler: don't oops on failure to load
drm/amdgpu: don't oops on failure to load (v2)
drm/amdgpu: don't VT switch on suspend
...
OCTEON Pre-SDK-1.8.1 bootloaders can not handle PT_NOTE program headers,
so do not emit them.
Before the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 2 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
NOTE 0x00000000004e02e0 0xffffffff815df2e0 0xffffffff815df2e0
0x0000000000000024 0x0000000000000024 R 4
After the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 1 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
The patch was tested on DSR-1000N router.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11403/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Discard .MIPS.abiflags from vmlinux. It's not needed and will cause
issues e.g. with old OCTEON bootloaders that cannot tolerate
additional program headers.
Before the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 3 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
ABIFLAGS 0x00000000005e77f0 0xffffffff816e67f0 0xffffffff816e67f0
0x0000000000000018 0x0000000000000018 R 8
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
NOTE 0x00000000004e02e0 0xffffffff815df2e0 0xffffffff815df2e0
0x0000000000000024 0x0000000000000024 R 4
After the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 2 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
NOTE 0x00000000004e02e0 0xffffffff815df2e0 0xffffffff815df2e0
0x0000000000000024 0x0000000000000024 R 4
Suggested-by: Matthew Fortune <matthew.fortune@imgtec.com>
Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11402/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Because #DB is now intercepted unconditionally, this callback
only operates on #BP for both VMX and SVM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is needed to avoid the possibility that the guest triggers
an infinite stream of #DB exceptions (CVE-2015-8104).
VMX is not affected: because it does not save DR6 in the VMCS,
it already intercepts #DB unconditionally.
Reported-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was found that a guest can DoS a host by triggering an infinite
stream of "alignment check" (#AC) exceptions. This causes the
microcode to enter an infinite loop where the core never receives
another interrupt. The host kernel panics pretty quickly due to the
effects (CVE-2015-5307).
Signed-off-by: Eric Northup <digitaleric@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch enhances dump_vmcs() to dump the value of TSC multiplier
field in VMCS.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch makes kvm-intel to return a scaled host TSC plus the TSC
offset when handling guest readings to MSR_IA32_TSC.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch makes kvm-intel module to load TSC scaling ratio into TSC
multiplier field of VMCS when a vcpu is loaded, so that TSC scaling
ratio can take effect if VMX TSC scaling is enabled.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch exhances kvm-intel module to enable VMX TSC scaling and
collects information of TSC scaling ratio during initialization.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch makes KVM use virtual_tsc_khz rather than the host TSC rate
as vcpu's TSC rate to compute the time scale if TSC scaling is enabled.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both VMX and SVM scales the host TSC in the same way in call-back
read_l1_tsc(), so this patch moves the scaling logic from call-back
read_l1_tsc() to a common function kvm_read_l1_tsc().
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For both VMX and SVM, if the 2nd argument of call-back
adjust_tsc_offset() is the host TSC, then adjust_tsc_offset() will scale
it first. This patch moves this common TSC scaling logic to its caller
adjust_tsc_offset_host() and rename the call-back adjust_tsc_offset() to
adjust_tsc_offset_guest().
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both VMX and SVM calculate the tsc-offset in the same way, so this
patch removes the call-back compute_tsc_offset() and replaces it with a
common function kvm_compute_tsc_offset().
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both VMX and SVM propagate virtual_tsc_khz in the same way, so this
patch removes the call-back set_tsc_khz() and replaces it with a common
function.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX and SVM calculate the TSC scaling ratio in a similar logic, so this
patch generalizes it to a common TSC scaling function.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
[Inline the multiplication and shift steps into mul_u64_u64_shr. Remove
BUG_ON. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch moves the field of TSC scaling ratio from the architecture
struct vcpu_svm to the common struct kvm_vcpu_arch.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The number of bits of the fractional part of the 64-bit TSC scaling
ratio in VMX and SVM is different. This patch makes the architecture
code to collect the number of fractional bits and other related
information into variables that can be accessed in the common code.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
John Crispin