Change the type of intel_crtc_state->shared_dpll to be a pointer to a
shared dpll. With this there is no need to first convert the id stored
in the crtc state to a pointer in order to use it. It does introduce a
bit of hassle on doing the opposite.
The long term objective is to hide details about dpll ids behind the
shared dpll interface.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-5-git-send-email-ander.conselvan.de.oliveira@intel.com
Currently we check if the encoder's idea of dotclock agrees with what
we calculated based on the FDI parameters. We do this in the encoder
.get_config() hooks, which isn't so nice in case the BIOS (or some other
outside party) made a mess of the state and we're just trying to take
over.
So as a prep step to being able sanitize such a bogus state, move the
the sanity check to just after we've read out the entire state. If
we then need to sanitize a bad state, it should be easier to move the
sanity check to occur after sanitation instead of before it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-13-git-send-email-imre.deak@intel.com
The pre-retina MacBook Pro uses an LVDS panel and a gmux controller
to switch the panel between its two GPUs. The panel mode in VBIOS
is notoriously bogus on these machines and some models have no
VBIOS at all.
Use drm_get_edid_switcheroo() in lieu of drm_get_edid() on LVDS
if the vga_switcheroo handler is capable of temporarily switching
the panel's DDC lines to the integrated GPU. This allows us to
retrieve the EDID if the panel is currently muxed to the discrete GPU.
This only enables EDID probing on the pre-retina MBP (2008 - 2013).
The retina MBP (2012 - present) uses eDP and gmux is not capable of
switching AUX separately from the main link on these models.
This will be addressed in later patches.
List of pre-retina MBPs with dual GPUs, one of them Intel:
[MBP 6,2 2010 intel ILK + nvidia GT216 pre-retina 15"]
[MBP 6,1 2010 intel ILK + nvidia GT216 pre-retina 17"]
[MBP 8,2 2011 intel SNB + amd turks pre-retina 15"]
[MBP 8,3 2011 intel SNB + amd turks pre-retina 17"]
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
v3: Commit newly added due to introduction of drm_get_edid_switcheroo()
wrapper which drivers need to opt-in to.
v5: Rebase on "vga_switcheroo: Add handler flags infrastructure",
i.e. call drm_get_edid_switcheroo() only if the handler
indicates that DDC is switchable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/bb095e14a2259be7fdd10092f9d6874a9be8f27b.1452525860.git.lukas@wunner.de
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
Minor fixup to d0669d0075 ("drm/i915: Clean up LVDS register
handling") which intended to read lvds_reg just once at the
beginning of intel_lvds_init() and use that throughout the rest
of the function but accidentally missed one register readout.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20151107141244.AB7616E242@gabe.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Keep single 'lvds_reg' and 'lvds' variable around in
intel_lvds_init(), and read it just once at the start.
Also intel_lvds_get_config() doesn't need to figure out which reg to use
since it can just consult lvds_encoder->reg.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always name any variable pointing at the adjusted mode as
'adjustead_mode'. This will make it much easier to identify
when we should use the crtc_ timings and when we shoudln't.
Conversion was performed with coccinelle:
@@
expression E;
identifier I;
@@
- struct drm_display_mode *I = &E.adjusted_mode;
+ struct drm_display_mode *adjusted_mode = &E.adjusted_mode;
<...
- I
+ adjusted_mode
...>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
[danvet: Fixup conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers exist only before GEN5, so currently we may access
undefined registers on VLV/CHV and BXT. Apply the workaround only pre
GEN5.
Since the workaround is relevant only when LVDS is present, for clarity
apply it only if this is the case.
This triggered an unclaimed register access warning on BXT.
v2: (Ville)
- move the workaround to the LVDS init code
- print a debug note about the workaround
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register exists only pre GEN5, but atm we also access it on
VLV/BXT/CHV. Prevent accessing it on these latter platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to LVDS.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- moved supported dotclock check from mode_valid() to intel_lvds_init()
V5:
- dotclock check moved back to mode_valid() function
- dotclock check for fixed mode
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of all the ad-hoc updating, duplicate the old state first
before reading out the hw state, then restore it.
intel_display_resume is a new function that duplicates the sw state,
then reads out the hw state, and commits the old state.
intel_display_setup_hw_state now only reads out the atomic state.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90396
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the correct pipe vs port disable sequence for the PCH LVDS
ports, ie. disable the port after the pipe.
Other PCH port were already converted in the following commits:
1ea56e269e drm/i915: Disable CRT port after pipe on PCH platforms
3c65d1d1bb drm/i915: Disable SDVO port after the pipe on PCH platforms
a4790cec3a drm/i915: Disable HDMI port after the pipe on PCH platforms
08aff3fe26 drm/i915: Move DP port disable to post_disable for pch platforms
but LVDS was forgotten.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new DRRS code it kinda sticks out, and we never managed to
get this to work well enough without causing issues. Time to wave
goodbye.
I've decided to keep the logic for programming the reduced clocks
intact, but everything else is gone. If anyone ever wants to resurrect
this we need to redo it all anyway on top of the frontbuffer tracking.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On older gen, pre-Ironlake, parts there is no hardwired pin to report
the presence of an LVDS panel. Instead, we have to rely on the VBT to
declare whether the machine has a panel or not. Though notoriously
unreliable, so far we have erred on the side of false-positives and have
required a list of machines which end up falsely reporting a panel as
present. However, we now have reports of false-negatives, machines with
an LVDS that are being ignored due to the VBT not declaring the panel.
This patch ignores the VBT setting if the BIOS has already enabled the
LVDS panel (and on Ironlake+ we also have the hardware presence pin).
It fixes the Samsung NP680Z5E-X01FR in the bug report, but is likely to
result in more false-positives, and since we rely on the BIOS to enable
the panel, there are likely different circumstances where the BIOS will
not enable that panel (and so we may see the same machine with and
without a panel all on the whim of the BIOS).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90979
Reported-and-tested-by: lysxia@gmail.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVWh3TAAoJEHm+PkMAQRiG/kwH/2c9irodp2+M9OUnX2bfsBb6
LnChiDpvkF5BB8jhP6d/XmvPp4NJzAbTxByhjdfb2E2HkorCUHCOIn2tI1TE2pUs
2qjkOVH+XCzoV0goGtQjzK1ht8f2IrtlDiEjyRekK5cJHzhggb22QPtWL4npyd0O
reDmG2jsRaF9POr9uLSFEv4CEnkksmRLUU0vuQX0TZeCJ41O7TXrkN/wKrLZ5mj4
IWpqXQaSlrffq/T5HnVbXBxk3/T8QmhrIoppiMpV1mUVj0uTqlFRNi5qwT2Nit1h
FVljWI4+WgOk3bf7fUlp+ahopjkTgu+GuXkiRP/pdgWNQO0cxCWSAzSndAlIIAE=
=uOoJ
-----END PGP SIGNATURE-----
Backmerge v4.1-rc4 into into drm-next
We picked up a silent conflict in amdkfd with drm-fixes and drm-next,
backmerge v4.1-rc5 and fix the conflicts
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/drm_irq.c
Single channel LVDS maxes out at 112 MHz. The 15" pre-retina models
shipped with 1440x900 (106 MHz) by default or 1680x1050 (119 MHz)
as a BTO option, both versions used dual channel LVDS even though
the smaller one would have fit into a single channel.
Notes:
Bug report showing that the MacBookPro8,2 with 1440x900 uses dual
channel LVDS (this lead to it being hardcoded in intel_lvds.c by
Daniel Vetter with commit 618563e394):
https://bugzilla.kernel.org/show_bug.cgi?id=42842
If i915.lvds_channel_mode=2 is missing even though the machine needs
it, every other vertical line is white and consequently, only the left
half of the screen is visible (verified by myself on a MacBookPro9,1).
Forum posting concerning a MacBookPro6,2 with 1440x900, author is
using i915.lvds_channel_mode=2 on the kernel command line, proving
that the machine uses dual channels:
https://bbs.archlinux.org/viewtopic.php?id=185770
Chi Mei N154C6-L04 with 1440x900 is a replacement panel for all
MacBook Pro "A1286" models, and that model number encompasses the
MacBookPro6,2 / 8,2 / 9,1. Page 17 of the panel's datasheet shows it's
driven with dual channel LVDS:
http://www.ebay.com/itm/-/400690878560http://www.everymac.com/ultimate-mac-lookup/?search_keywords=A1286http://www.taopanel.com/chimei/datasheet/N154C6-L04.pdf
Those three 15" models, MacBookPro6,2 / 8,2 / 9,1, are the only ones
with i915 graphics and dual channel LVDS, so that list should be
complete. And the 8,2 is already in intel_lvds.c.
Possible motivation to use dual channel LVDS even on the 1440x900
models: Reduce the number of different parts, i.e. use identical logic
boards and display cabling on both versions and the only differing
component is the panel.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
[Jani: included notes in the commit message for posterity]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Single channel LVDS maxes out at 112 MHz, anything above must be dual
channel. This avoids the need to specify i915.lvds_channel_mode=2 on
all 17" MacBook Pro models with i915 graphics since they had 1920x1200
(193 MHz), plus those 15" pre-retina models which had a resolution
of 1680x1050 (119 MHz) as a BTO option.
Source for 112 MHz limit of single channel LVDS is section 2.3 of:
https://01.org/linuxgraphics/sites/default/files/documentation/ivb_ihd_os_vol3_part4.pdf
v2: Avoid hardcoding 17" models by assuming dual channel LVDS if the
resolution necessitates it, suggested by Jani Nikula.
v3: Fix typo, thanks Joonas Lahtinen.
v4: Split commit in two, suggested by Ville Syrjälä.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
[Jani: included spec reference into the commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.
Broken by
commit 944b0c7657
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri Mar 20 16:18:07 2015 +0200
drm/i915: Copy the staged connector config to the legacy atomic state
v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.
v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be helpful for adding future platforms. It is better to keep
the information in the single point of truth (the table) instead of
duplicating it into the validity function.
While at it, add dev_priv parameter to the function, also to prepare for
adding future platform support.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename intel_gmbus_is_port_valid to intel_gmbus_is_valid_pin, and rename
port parameters to pin as well. This matches usage all around, as
usually a pin is passed to the validity check function. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs refer to pin pairs. Start moving towards using pin rather than
port all around to avoid confusion. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that we can add connector states to the drm_atomic_state used in the
legacy modeset.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As vendors transition their drivers from legacy to atomic there's some
duplication of data between drm_crtc and drm_crtc_state (since
unconverted drivers likely won't have a state structure).
i915 is partially converted and does have a crtc->state structure, but
still uses direct crtc fields internally in many places, which causes
the two sets of data to get out of sync. As of commit
commit 31c946e85c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Feb 22 12:24:17 2015 +0100
drm: If available use atomic state in getcrtc ioctl
This way drivers fully converted to atomic don't need to update these
legacy state variables in their modeset code any more.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
the DRM core starts assuming that the presence of a ->state structure
implies that it should make use of the values stored there which, on
i915, leads to the core code using stale values for CRTC 'enabled'
status.
Let's switch over to using the state value of 'enable' internally rather
than using the drm_crtc field. This ensures that our driver internals
are working from the same data that the DRM core is, avoiding
mismatches.
This patch was generated with Coccinelle using the following semantic
patch:
<smpl>
@@
struct drm_crtc C;
struct drm_crtc *CP;
@@
(
- C.enabled
+ C.state->enable
|
- CP->enabled
+ CP->state->enable
)
// For assignments, we still update the legacy value as well as the state value
// so add an extra assignment statement for that.
@@
struct drm_crtc C;
struct drm_crtc *CP;
expression E;
@@
(
C.state->enable = E;
+ C.enabled = E;
|
CP->state->enable = E;
+ CP->enabled = E;
)
</smpl>
The crtc->mode and crtc->hwmode fields should probably be transitioned
over as well eventually, but we seem to do an okay job of keeping those
up-to-date already so I want to minimize the changes that will clash
with Ander's in-progress atomic work.
v2: Don't remove the assignments to the legacy value when we assign to
the state value. A second cocci stanza takes care of adding the
legacy assignment back where appropriate. (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though we only support atomic plane updates at the moment, we still
need to add an .atomic_get_property() entrypoint for connectors before
we allow the driver to flip on the DRIVER_ATOMIC bit. As soon as that
bit gets set, the DRM core will start adding atomic connector properties
(in addition to the plane properties we care about at the moment), so we
need to be able to handle the new way the DRM core will interact with
us.
For simplicity, we just lookup driver-specific connector properties in
the usual shadow array maintained by the core. Once we get real atomic
modeset support for crtc's and planes, this code should be re-written to
pull the data out of crtc/connector state structures.
v2: Fix intel_dvo and intel_dsi that I missed on the first pass (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to enable/test plane updates via the atomic interface, but as
soon as we flip DRIVER_ATOMIC on, the DRM core will take some atomic
codepaths to lookup properties during drmModeGetConnector() and some of
those codepaths unconditionally dereference connector->state
(specifically when looking up the CRTC ID property in
drm_atomic_connector_get_property()). Create a dummy connector state
for each connector at init time to ensure the DRM core doesn't try to
dereference a NULL connector->state. The actual connector properties
will never be updated or contain useful information, but since we're
doing this specifically for testing/debug of the plane operations (and
only when a specific kernel module option is given), that shouldn't
really matter.
Once we start creating connector states, the DRM core will want to be
able to clean them up for us. We also need to hook up the destruction
entrypoint to the core's helper.
v2: Squash in the patch to set the state destruction hook (Ander & Bob)
v3: Only create dummy connector states when we're actually faking
atomic support. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.
@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member
v2: Clarify manual changes by splitting them into another patch. (Matt)
Improve cocci script to generate even more of the changes. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:
@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhNLZAAoJEHm+PkMAQRiGAEcH/iclYDW7k2GKemMqboy+Ohmh
+ELbQothNhlGZlS1wWdD69LBiiXkkQ+ufVYFh/hC0oy0gUdfPMt5t+bOHy6cjn6w
9zOcACtpDKnqbOwRqXZjZgNmIabk7lRjbn7GK4GQqpIaW4oO0FWcT91FFhtGSPDa
tjtmGRqDmbNsqfzr18h0WPEpUZmT6MxIdv17AYDliPB1MaaRuAv1Kss05TJrXdfL
Oucv+C0uwnybD9UWAz6pLJ3H/HR9VJFdkaJ4Y0pbCHAuxdd1+swoTpicluHlsJA1
EkK5iWQRMpcmGwKvB0unCAQljNpaJiq4/Tlmmv8JlYpMlmIiVLT0D8BZx5q05QQ=
=oGNw
-----END PGP SIGNATURE-----
Merge tag 'v3.18' into drm-next
Linux 3.18
Backmerge Linus tree into -next as we had conflicts in i915/radeon/nouveau,
and everyone was solving them individually.
* tag 'v3.18': (57 commits)
Linux 3.18
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
uapi: fix to export linux/vm_sockets.h
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
ahci: disable MSI on SAMSUNG 0xa800 SSD
context_tracking: Restore previous state in schedule_user
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/nouveau/nouveau_drm.c
drivers/gpu/drm/radeon/radeon_cs.c
Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in
commit c31407a367
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Oct 18 21:07:01 2012 +0100
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- fini goes with init, so call it intel_power_domains_fini. While
at it shovel some of the fini code that leaked out of it back in.
- give power_enabled functions the verb _is_ to make the meaning clearer.
Also use a __ prefix instead of _unlocked to really discourage users.
- rename runtime_pm_init/fini to enable/disable since that's what they do.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
The __init annotations for the DMI callback functions are wrong as this
code can be called even after the module has been initialized, e.g. like
this:
# echo 1 > /sys/bus/pci/devices/0000:00:02.0/remove
# modprobe i915
# echo 1 > /sys/bus/pci/rescan
The first command will remove the PCI device from the kernel's device
list so the second command won't see it right away. But as it registers
a PCI driver it'll see it on the third command. If the system happens to
match one of the DMI table entries we'll try to call a function in long
released memory and generate an Oops, at best.
Fix this by removing the bogus annotation.
Modpost should have caught that one but it ignores section reference
mismatches from the .rodata section. :/
Fixes: 25e341cfc3 ("drm/i915: quirk away broken OpRegion VBT")
Fixes: 8ca4013d70 ("CHROMIUM: i915: Add DMI override to skip CRT...")
Fixes: 425d244c86 ("drm/i915: ignore LVDS on intel graphics systems...")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au> # Can modpost be fixed?
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Following the established idom, let's provide a macro to iterate through
the encoders.
spatch helps, once more, for the substitution:
@@
iterator name list_for_each_entry;
iterator name for_each_intel_encoder;
struct intel_encoder * encoder;
struct drm_device * dev;
@@
-list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
+for_each_intel_encoder(dev, encoder) {
...
}
I also modified a few call sites by hand where a pointer to mode_config
was directly used (to avoid overflowing 80 chars).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Wrap paramters correctly in the macro and remove spurious
space checkpatch noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- fbc improvements when stolen memory is tight (Ben)
- cdclk handling improvements for vlv/chv (Ville)
- proper fix for stuck primary planes on gmch platforms with cxsr (Imre&Ebgert
Eich)
- gen8 hw semaphore support (Ben)
- more execlist prep work from Oscar Mateo
- locking fixes for primary planes (Matt Roper)
- code rework to support runtime pm for dpms on hsw/bdw (Paulo, Imre & me), but
not yet enabled because some fixes from Paulo haven't made the cut
- more gpu boost tuning from Chris
- as usual piles of little things all over
* tag 'drm-intel-next-2014-07-11' of git://anongit.freedesktop.org/drm-intel: (93 commits)
drm/i915: Make the RPS interrupt generation mask handle the vlv wa
drm/i915: Move RPS evaluation interval counters to i915->rps
drm/i915: Don't cast a pointer to void* unnecessarily
drm/i915: don't read LVDS regs at compute_config time
drm/i915: check the power domains in intel_lvds_get_hw_state()
drm/i915: check the power domains in ironlake_get_pipe_config()
drm/i915: don't skip shared DPLL assertion on LPT
drm/i915: Only touch WRPLL hw state in enable/disable hooks
drm/i915: Switch to common shared dpll framework for WRPLLs
drm/i915: ->enable hook for WRPLLs
drm/i915: ->disable hook for WRPLLs
drm/i915: State readout support for WRPLLs
drm/i915: add POWER_DOMAIN_PLLS
drm/i915: Document that the pll->mode_set hook is optional
drm/i915: Basic shared dpll support for WRPLLs
drm/i915: Precompute static ddi_pll_sel values in encoders
drm/i915: BDW also has special-purpose DP DDI clocks
drm/i915: State readout and cross-checking for ddi_pll_sel
drm/i915: Move ddi_pll_sel into the pipe config
drm/i915: Add a debugfs file for the shared dpll state
...
This reverts commit 773875bfb6.
It is very much needed and the lack of dithering has been reported by
a large list of people with various gen2/3 hardware.
Also, the original patch was complete non-sense since the WARNING
backtraces in the references bugzilla are about
gmch_pfit.lvds_border_bits mismatch, not at all about the dither bit.
That one seems to work.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may reach this point while the machine is still runtime suspended,
so we'll hit a WARN. The other encoders also don't touch registers at
this point, so instead of waking the machine up, write some code to
keep the register always at the same state, including after we runtime
suspend/resume.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we do for the other encoders. This should fix some WARNs
when running pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bjørn Mork