CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function pinctrl_register() returns
NULL not ERR_PTR(). The PTR_ERR() in the return value
should be replaced with error no.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pointer to "pdev->dev" is already stored in "dev", so use it in
devm_request_and_ioremap().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bill Pemberton