This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The check for the "elm_id" binding had been removed.
This causes nand boot to fail on boards still using
the old binding. Update the bindings on those boards.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.
For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.
Read speed increases from 7869 KiB/ to 8875 KiB/s
and write speed was unchanged at 5100 KiB/s.
Measured using mtd_speedtest.ko on am335x-evm.
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM335x TRM: SPRUH73L: 7.1.3.3.12.2 NAND Device-Ready Pin
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the AM33xx pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.
The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.
Let's fix the issue according to the following table:
Device GPMC partition size Device IO size
connected in the ranges entry in the reg entry
NAND 0x01000000 (16MB) 4
16550 0x01000000 (16MB) 8
smc91x 0x01000000 (16MB) 0xf
smc911x 0x01000000 (16MB) 0xff
OneNAND 0x01000000 (16MB) 0x20000 (128KB)
16MB NOR 0x01000000 (16MB) 0x01000000 (16MB)
32MB NOR 0x02000000 (32MB) 0x02000000 (32MB)
64MB NOR 0x04000000 (64MB) 0x04000000 (64MB)
128MB NOR 0x08000000 (128MB) 0x08000000 (128MB)
256MB NOR 0x10000000 (256MB) 0x10000000 (256MB)
Let's also add comments to the fixed entries while at it.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As this board use external clock for RMII interface we should specify 'rmii'
phy mode and 'rmii-clock-ext' to make ethernet working.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739faba ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:
o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Javier Martinez Canillas