Currently the LCD is turned on thanks to the bootloader initialization.
In order to make the kernel to turn on the LCD on is own, pass the
'enable-gpios' and 'power-supply' properties.
Also, the GPIO1_IO01 is not used as PWM functionality on this board. It is
connected to the PWREN pin of connector J14 and has a GPIO function, so
remove the PWM1 node and change the GPIO1_IO01 IOMUX to GPIO function.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is preferred to use the panel compatible string rather than passing the
LCD timming in the device tree.
So pass the "innolux,at043tn24" compatible string to describe the parallel
LCD on this board.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the phy-reset-gpios property so that Ethernet PHYs can go
through a proper reset.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to mx7sabresd schematics the MIPI CSI/DSI voltage rails
should be 2.8V but the voltage provided is a maximum of 3.3V and
minimum of 1.8V. Providing such a higher voltage might damage the
peripherals and violates the schematic settings.
Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb has a BCM4339 BT chip connected to UART6.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb has a BCM4339 Wifi chip connected to USDHC2.
Add support for it.
While at it, move the WL_REG_ON pin to the correct pinctrl node.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.
The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjWLQAAoJEFBXWFqHsHzOGt0H/2WCsuRi6WU7i7Wyk/S0Xq5t
HzA/9m2f7z1vb1tzFknbpcWYa9bdofI7Dz+6KW2vp4fxhMyJn8SQxWwQjVNya2ba
z8XLdEMlIuozBebPcH84ovNzqoBIOEFahGm5smm40s/o7XL8ua9tOEFaUc+jY0Pd
n/3TPmoyBTlbrgiCZfLXCVsczHtEVW5JoQmXT7aDsxT0BQpnwLbgXKVOxgDvsWXM
WtAKjpGvdiApD3znbFjYmRKak+2uilkV5B4jrL4mZf8dxCliykP4XA/LbiMLKAMN
voMpTtTK7UYp59GrwKbqfJ+pPU7b6ndKK59f7FWrTDNgtDGe+J4ExjWwsDnuLfI=
=HAbg
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.11:
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
* tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (32 commits)
ARM: dts: udoo_neo: Add Bluetooth support
ARM: dts: udoo_neo: Add Wifi support
ARM: dts: udoo_neo: Add UDOO Neo USB OTG1 and OTG2 support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL NAND initial support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL eMMC initial support
ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
ARM: dts: vf610-zii-dev: add EEPROM entry to Rev C
ARM: dts: add Armadeus Systems OPOS6UL and OPOS6ULDEV support
ARM: dts: imx6q-utilite-pro: enable 2nd display pipeline
ARM: dts: vf610-zii-dev: Add .dts file for rev. C
ARM: dts: vf610-zii-dev-rev-b: Remove leftover PWM pingroup
ARM: dts: imx6: Support Savageboard quad
ARM: dts: imx6: Support Savageboard dual
ARM: dts: imx6: Add Savageboard common file
ARM: dts: imx53-qsb: Provide the TVE DAC regulators
ARM: dts: imx6q: Add mccmon6 board support
Doc: devicetree: bindings: Add vendor prefix entry - lwn
ARM: dts: imx/vf: Correct license text
ARM: dts: imx25.dtsi: DryIce security violation interrupt
ARM: dts: imx: Add ocotp node for imx6ul
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX7 has two iomux controllers. the iomuxc and the iomuxc_lpsr.
In a board dts we have to make sure that both controllers are supplied
with the correct pins. It's way too easy to do this wrong since only
a look into the reference manual can reveal which pins belong to which
controller. To make this clearer add "LPSR" to the pin names which
belong to the LPSR controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog pin and the pwm output pin are controlled by the
iomuxc_lpsr, not the regular iomux, so move the pins there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit b36581df7e ("spi: imx: Using existing properties for
chipselects") the device tree property 'fsl,spi-num-chipselects' is
unused and it is already marked as obsolete in device tree binding
documentation. Remove the property from the existing DTS files to
avoid its reoccurence on copying.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix misspelled "ti,x-plate-ohms" property name of TI TSC2046
touchscreen controller.
Fixes: d09e6beafa ("ARM: dts: imx7d-sdb: Add support for touchscreen")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The base device tree uses KEY_POWER in the snvs-powerkey node,
hence include the input.h header file in the base device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7Solo implements a subset of features available on
i.MX 7Dual. Recreate imx7s.dtsi as the base device tree for
i.MX 7Dual boards. The i.MX 7Dual's additional features over
i.MX 7Solo are:
- Second Cortex-A7 core
- Second Gigabit Ethernet controller
- EPD (Electronc Paper Display, not yet part of the device tree)
- PCIe (not yet part of the device tree)
- Additional USB2.0 OTG controller
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7 series currently consists of two SoCs: i.MX 7Solo and
7Dual. The former has a subset of features of the latter, hence
use imx7s.dtsi as the new base device tree. To keep diffstat nice,
just move imx7d.dtsi to imx7s.dtsi temporarily and recreate
imx7d.dtsi in a second commit.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for USBOTG1 and USBOTG2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
This patch add usdhc3 support for HS400
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marco Franchi