The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 876e7fb9f4 ("ARM: shmobile: r8a7794: alt: Enable VGA port")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C4 on the EXIO-B connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Update the PFC pin groups and function names of DU interface for
r8a7794 ALT board.
The currently specified pin groups and function names prevented PFC and
DU interfaces from being correctly configured:
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
rcar-du: probe of feb00000.display failed with error -22
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1}.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Define the Alt board dependent part of the MMCIF device node.
Like the Silk the board has eMMC chip along with the necessary voltage
regulator (note that the Vcc/Vccq regulator is dummy -- it's required by
the MMCIF driver but doesn't actually exist on the board).
Based on work for the Silk board by Vladimir Barinov and Sergei Shtylyov.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Alt board dependent part of the SDHI0 and 1
device nodes along with the necessary voltage regulators.
Based on work by the original patch by Vladimir Barinov and
Sergei Shtylyov for the Silk board.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the alt device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the QSPI controller in the alt device tree.
Based similar work for the silk board by by Vladimir Barinov and
Sergei Shtylyov.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
22b160713c ("ARM: shmobile: alt: Add pfc pins to DT") introduced pfc pins
to the alt device tree but did not reference them. This patch fixes ether
pfc by:
* Referencing ether pins
* Adding and referencing phy1 pins
* Removing ether b pins. These are not used in the configuration
of the alt board used for testing and empirically their presence
prevents ethernet from functioning correctly in that environment.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
22b160713c ("ARM: shmobile: alt: Add pfc pins to DT") introduced pfc pins
to the alt device tree but did not reference them. This patch fixes scif2
pfc by adding references to the scif2 pins.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tie in r8a7794 PFC DU support to the VGA port on the
r8a7794 ALT board.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds the device board-dependent part of the VIN0 device and its ADV7180
video decoder on I2C1, and the interconnection between them.
Based on silk patch by Sergei Shtylyov.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Defines the board-dependent part of the I2C1 device.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
PFC is already enabled on the r8a7794.
This adds pins for devices already enabled in DT on
the r8a7794 based alt board.
Based on work by Mitsuhiro Kimura and Hisashi Nakamura.
Cc: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Cc: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Enable the DU device and the VGA port available on the r8a7794
ALT board. The VGA portion of the ALT board is somewhat similar
to the Lager board but in case of ALT the DU1 pins are used
and the X2 clock has a reduced frequency.
This patch does not include any pinctrl (PFC) settings due to lack
of PFC DT integration on r8a7794. At this point the default state
of the boot loader is enough to keep the VGA port working without
changing any pinctrl settings.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PHY IRQ line is connected to external IRQ8, not IRQ0. Fix DT
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the ethernet controller for the Alt board. Pin muxing entries are
currently left out as r8a7794 pin control support isn't available yet.
We thus rely on the boot loader to configure ethernet pins for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While the DT parsing code recognizes "ok" as a valid value for the
"status" property, ePAPR v1.1 doesn't mention it in the list of valid
values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Alt is booted from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from chosen/bootargs.
This change has a side-effect of changing the console speed from 38400
to 115200. This is intentional as 115200 is consistently used on
all other shmobile boards.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
Note that we have to keep the "console=ttySC0,38400" parameter in
chosen/bootargs, else the console will use the default setting of 115200
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven