Add lpfc_sli_flush_mbox_queue() function and use it in lpfc_offline() call
to avoid deadlock on thread block.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use asynchronous ABTS completion to speed up abort completions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce lpfc_reset_barrier() function for resets on dual channel adapters
Workaround for a hardware errata on dual channel asics. There is a
potential for the chip to lock up on a reset if a shared dma engine is in
use. The (ugly) work around requires a reset process which uses a mailbox
command to synchronize the independent channels prior to the reset to
avoid the issue. Unfortunately, the timing windows required to ensure this
workaround succeeds are very specific, meaning we can't release the cpu
during the barrier.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed RSCN handling when a PLOGI is in retry.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix Discovery processing for NPorts that change their NPortId on the fly
due to a cable swap.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Handling of ELS commands RRQ, RPS, RPL and LIRR correctly
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Add functionality to run in polled mode only. Includes run time
attribute to enable mode.
- Enable runtime writable hba settings for coallescing and delay parameters
Customers have requested a mode in the driver to run strictly polled.
This is generally to support an environment where the server is extremely
loaded and is looking to reclaim some cpu cycles from adapter interrupt
handling.
This patch adds a new "poll" attribute, and the following behavior:
if value is 0 (default):
The driver uses the normal method for i/o completion. It uses the
firmware feature of interrupt coalesing. The firmware allows a
minimum number of i/o completions before an interrupt, or a maximum
time delay between interrupts. By default, the driver sets these
to no delay (disabled) or 1 i/o - meaning coalescing is disabled.
Attributes were provided to change the coalescing values, but it was
a module-load time only and global across all adapters.
This patch allows them to be writable on a per-adapter basis.
if value is 1 :
Interrupts are left enabled, expecting that the user has tuned the
interrupt coalescing values. When this setting is enabled, the driver
will attempt to service completed i/o whenever new i/o is submitted
to the adapter. If the coalescing values are large, and the i/o
generation rate steady, an interrupt will be avoided by servicing
completed i/o prior to the coalescing thresholds kicking in. However,
if the i/o completion load is high enough or i/o generation slow, the
coalescion values will ensure that completed i/o is serviced in a timely
fashion.
if value is 3 :
Turns off FCP i/o interrupts altogether. The coalescing values now have
no effect. A new attribute "poll_tmo" (default 10ms) exists to set
the polling interval for i/o completion. When this setting is enabled,
the driver will attempt to service completed i/o and restart the
interval timer whenever new i/o is submitted. This behavior allows for
servicing of completed i/o sooner than the interval timer, but ensures
that if no i/o is being issued, then the interval timer will kick in
to service the outstanding i/o.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return FAILED from eh_ routines if command(s) is(are) not completed
There were scenarios where we may have returned from the error
handlers prior to all affected commands being flushed to the midlayer.
Add changes to ensure this doesn't happen.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace lpfc_sli_issue_iocb_wait_high_priority with lpfc_sli_issue_iocb_wait.
Simplify code paths, as there really wasn't a "priority"
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: James Smart <James.Smart@emulex.com>
There were scenarios where the error handlers could reuse an iotag
value of an active io. Remove all possibility of this by
pre-assigning iotag resources to command resources.
Signed-off-by: James Smart <James.Smart@emulex.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Table was not providing a lot of value and injected a couple of
errors. Removed it and made functionality inline.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update copyright notice text and include year 2005.
Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add completion handler to the abort iocbs to close a hole where we
could reuse an iotag.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart