The CPTS HW latches and saves CPTS counter value in CPTS fifo immediately
after writing to CPSW_CPTS_PUSH.TS_PUSH (bit 0), so the total time that the
driver needs to read the CPTS timestamp is the time required CPSW_CPTS_PUSH
write to actually reach HW.
Hence switch CPTS driver to implement new .gettimex64() callback for more
precise measurement of the offset between a PHC and the system clock which
is measured as time between
write(CPSW_CPTS_PUSH)
read(CPSW_CPTS_PUSH)
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPTS driver .adjfreq() generates request to read CPTS current time
(CPTS_EV_PUSH) with intention to process all pending event using previous
frequency adjustment values before switching to the new ones. So
CPTS_EV_PUSH works as a marker to switch to the new frequency adjustment
values. Current code assumes that all job is done in .adjfreq(), but after
enabling IRQ this will not be true any more.
Hence save new frequency adjustment values (mult) and perform actual freq
adjustment in cpts_fifo_read() immediately after CPTS_EV_PUSH is received.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPTS HW time reading code is implemented in timecounter->cyclecounter
.read() callback and performs following operations:
timecounter_read() ->cc.read() -> cpts_systim_read()
- request current CPTS HW time CPTS_TS_PUSH.TS_PUSH = 1
- poll CPTS FIFO for CPTS_EV_PUSH event with current HW timestamp
This approach need to be changed for the future switch to PTP PHC
.gettimex64() callback, which require to separate requesting current CPTS
HW time and processing CPTS FIFO. And for the follow up patch, which
improves .adjfreq() implementation.
This patch moves code accessing CPTS HW out of timecounter code as
following:
- convert HW timestamp of every CPTS event to PTP time (us) and store it as
part struct cpts_event;
- add CPTS context field to store current CPTS HW time (counter) value and
update it on CPTS_EV_PUSH reception;
- move code accessing CPTS HW out of timecounter code and use current CPTS
HW time (counter) from CPTS context instead;
- ensure timecounter->cycle_last is updated on CPTS_EV_PUSH reception.
After this change CPTS timecounter will only perform timekeeper role
without actually accessing CPTS HW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_yy() API instead of pr_yy() for log outputs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to benefit from the new napi_defer_hard_irqs feature,
we need to use napi_complete_done() variant in this driver.
RX path is already using it, this patch implements TX completion side.
mlx4_en_process_tx_cq() now returns the amount of retired packets,
instead of a boolean, so that mlx4_en_poll_tx_cq() can pass
this value to napi_complete_done().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error recovery is handled by management firmware (MFW) with the help of
qed/qede drivers. Upon detecting the errors, driver informs MFW about this
event which in turn starts a recovery process. MFW sends ERROR_RECOVERY
notification to the driver which performs the required cleanup/recovery
from the driver side.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch enables the device to send error messages to root port when
an error is detected.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the bulk enqueue feature in .ndo_xdp_xmit.
We cannot use the XDP_XMIT_FLUSH since the architecture is not capable
to store all the frames dequeued in a NAPI cycle so we instead are
enqueueing all the frames received in a ndo_xdp_xmit call right away.
After setting up all FDs for the xdp_frames received, enqueue multiple
frames at a time until all are sent or the maximum number of retries is
hit.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having a function that both creates a frame descriptor from
an xdp_frame and enqueues it, split this into two stages.
Add the dpaa2_eth_xdp_create_fd that just transforms an xdp_frame into a
FD while the actual enqueue callback is called directly from the ndo for
each frame.
This is particulary useful in conjunction with bulk enqueue.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dpaa2-eth driver to use the bulk enqueue function introduced
with the change to QBMAN ring mode. At the moment, no functional changes
are made but rather the driver just transitions to the new interface
while still enqueuing just one frame at a time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enqueue dpaa2-eth callback now returns the number of successfully
enqueued frames. This is a preliminary patch necessary for adding
support for bulk ring mode enqueue.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detection by
compatible, on other hand we should be able to reset complete chip
before PHY1 configured it, and we need to define dependencies for proper
power management.
We can solve it by defining PHY1 as child of PHY0:
tja1102_phy0: ethernet-phy@4 {
reg = <0x4>;
interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
reset-assert-us = <20>;
reset-deassert-us = <2000>;
tja1102_phy1: ethernet-phy@5 {
reg = <0x5>;
interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
};
};
The PHY1 should be a subnode of PHY0 and registered only after PHY0 was
completely reset and initialized.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For
example PHY 1 has no PHY ID and no health monitor.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IS_ERR() and PTR_ERR() instead of PTR_ZRR_OR_ZERO()
to simplify code, avoid redundant paramenter definitions
and judgements.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid.
This PHY has an internal RX delay of 1.2ns and no delay for TX.
The pad skew registers allow to set the total TX delay to max 1.38ns and
the total RX delay to max of 2.58ns (configurable 1.38ns + build in
1.2ns) and a minimal delay of 0ns.
According to the RGMII v1.3 specification the delay provided by PCB traces
should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this
delay by MAC or PHY. So, we configure this PHY to the best values we can
get by this HW: TX delay to 1.38ns (max supported value) and RX delay to
1.80ns (best calculated delay)
The phy-modes can still be fine tuned/overwritten by *-skew-ps
device tree properties described in:
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dwmac4, enable VLAN promiscuity when MAC controller is requested to
enter promiscuous mode.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan_hash_lookup() uses list_for_each_entry_rcu() for traversing
should either under RCU in fast path or the protection of rtnl_mutex.
In the case of holding RTNL, we should add the corresponding lockdep
expression to silence the following false-positive warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc1-next-20200416-00003-ga3b8d28bc #1 Not tainted
-----------------------------
drivers/net/macvlan.c:126 RCU-list traversed in non-reader section!!
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it can be seen that the VSC9959 (Felix) switch will not flood
frames if they have a VLAN tag with a PCP of 1-7 (nonzero).
It turns out that Felix is quite different from its cousin, Ocelot, in
that frame flooding can be allowed/denied per traffic class. Where
Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8.
The approach that this driver is going to take is "thanks, but no
thanks". We have no use case of limiting the flooding domain based on
traffic class, so we just want to allow packets to be flooded, no matter
what traffic class they have.
So we copy the line of code from ocelot.c which does the one-shot
initialization of the flooding PGIDs, and we add it to felix.c as well -
except replicated 8 times.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY supports monitoring its die temperature as well as two analog
voltages. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit
Ethernet transceiver.
This also adds support for tunables to set and get downshift and
energy detect auto power-down.
The PHY has four ports and each port has its own PHY address.
There are per-port registers as well as global registers.
Unfortunately, the global registers can only be accessed by reading
and writing from/to the PHY address of the first port. Further,
there is no way to find out what port you actually are by just
reading the per-port registers. We therefore, have to scan the
bus on the PHY probe to determine the port and thus what address
we need to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An attempt was made in commit fe3490e610 ("net: mscc: ocelot: Hardware
ofload for tc flower filter") to avoid clashes between MAC_ETYPE rules
and IP rules. Because the protocol blacklist should have included
ETH_P_ALL too, it created some confusion, but now the situation should
be dealt with a bit better by the patch immediately previous to this one
("net: mscc: ocelot: refine the ocelot_ace_is_problematic_mac_etype
function").
So now we can remove that check. MAC_ETYPE rules with a protocol of
ETH_P_IP, ETH_P_IPV6, ETH_P_ARP and ETH_P_ALL _are_ supported, with some
restrictions regarding per-port exclusivity which are enforced now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit mentioned below was a bit too harsh, and while it restricted
the invalid key combinations which are known to not work, such as:
tc filter add dev swp0 ingress proto ip \
flower src_ip 192.0.2.1 action drop
tc filter add dev swp0 ingress proto all \
flower src_mac 00:11:22:33:44:55 action drop
it also restricted some which still should work, such as:
tc filter add dev swp0 ingress proto ip \
flower src_ip 192.0.2.1 action drop
tc filter add dev swp0 ingress proto 0x22f0 \
flower src_mac 00:11:22:33:44:55 action drop
What actually does not match "sanely" is a MAC_ETYPE rule on frames
having an EtherType of ARP, IPv4, IPv6, in addition to SNAP and OAM
frames (which the ocelot tc-flower implementation does not parse yet, so
the function might need to be revisited again in the future).
So just make the function recognize the problematic MAC_ETYPE rules by
EtherType - thus the VCAP IS2 can be forced to match even on those
packets.
This patch makes it possible for IP rules to live on a port together
with MAC_ETYPE rules that are non-all, non-arp, non-ip and non-ipv6.
Fixes: d4d0cb741d7b ("net: mscc: ocelot: deal with problematic MAC_ETYPE VCAP IS2 rules")
Reported-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the filter's protocol is ignored except for a few special
cases (IPv4 and IPv6).
The EtherType can be matched inside VCAP IS2 by using a MAC_ETYPE key.
So there are 2 cases in which EtherType matches are supported:
- As part of a larger MAC_ETYPE rule, such as:
tc filter add dev swp0 ingress protocol ip \
flower skip_sw src_mac 42:be:24:9b:76:20 action drop
- Standalone (matching on protocol only):
tc filter add dev swp0 ingress protocol arp \
flower skip_sw action drop
As before, if the protocol is not specified, is it implicitly "all" and
the EtherType mask in the MAC_ETYPE half key is set to zero.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support 4 PTP programmable pins with only PTP_PF_PEROUT function
for now. The PTP_PF_EXTTS function will be supported in the
future, and it should be implemented separately for Felix and
Ocelot, because of different hardware interrupt implementation
in them.
Since the hardware is not able to support absolute start time,
the periodic clock request only allows start time 0 0. But nsec
could be accepted for PPS case for phase adjustment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timestamp info should be only software timestamp capabilities
if ptp clock does not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change nfp driver to use globally defined kernel version.
Reported-by: Borislav Petkov <bp@suse.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use globally defined kernel version instead of custom driver variant.
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have parentheses around plain pointer variable or
negation operator. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's convenient to use get_unligned_beXX() and put_unaligned_beXX() helpers
to get or set MAC instead of open-coded variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conversion to devm_clk_get_optional() makes it explicit that clocks are
optional. This change allows to handle deferred probe in case clocks are
defined, but not yet probed. Due to above changes bail out in error case.
While here, check potential error when enable main clock.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing which needs a set of OF headers, followed by redundant
OF node ID check. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiled with CONFIG_ACPI=n, ACPI_PTR() will be no-op, and thus
genet_acpi_match table defined, but not used. Compiler is not happy about
such data. Drop ACPI_PTR() for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes misc updates and clean ups to mlx5 driver:
1) improve some comments from Hu Haowen.
2) Handles errors of netif_set_real_num_{tx,rx}_queues, from Maxim
3) IPsec and FPGA related code cleanup to prepare for ASIC devices
IPsec offloads, from Raed
4) Allow partial mask for tunnel options, from Roi.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl6eEhUACgkQSD+KveBX
+j6rXAf/flM2mYB8moFIqmsSgO6yDnskK9InshCcidM3gqv989dyms1NStv4SzEq
U2zQLGTinlGHEkCW6BJtMQYGatGRIX9DcpZUGYQqSL18ihZ9HkB5R+Dfw8+jRDTI
AIyYoAjpmnAahzJ9xbqtzMPzunlCahdzmfuNjw6mA4QterlllOc5HLqrCi/Rk93Z
WNCo0WRH+6ZfGoC9em/C73n1WDb990QOl51L+8/iSNcuMCeN74Vo5Bs/lJaEKGeV
DQxiE3/wijWmdpBBeVJgXPFKT10W5aPlt7DuYWvTwVJcwtIV3KFrIP5prtHuu4w1
nv09RVihQkGloSzZeM9XHNX0WU4nVg==
=Q2sm
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-04-20
This series includes misc updates and clean ups to mlx5 driver:
1) improve some comments from Hu Haowen.
2) Handles errors of netif_set_real_num_{tx,rx}_queues, from Maxim
3) IPsec and FPGA related code cleanup to prepare for ASIC devices
IPsec offloads, from Raed
4) Allow partial mask for tunnel options, from Roi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A barrier is needed here to ensure that rtl_tx sees the descriptor
changes (DescOwn set) before the updated tp->cur_tx value. Else it may
wrongly assume that the transfer has been finished already. For this
purpose smp_wmb() is sufficient.
No separate barrier is needed for ordering the descriptor changes
with the MMIO doorbell write. The needed barrier is included in
the non-relaxed writel() used by rtl8169_doorbell().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedded CPU bit doesn't change with PCI resume/suspend.
Hence read it only once while probing the PCI device.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
netif_set_real_num_tx_queues and netif_set_real_num_rx_queues may fail.
Now that mlx5e supports handling errors in the preactivate hook, this
commit leverages that functionality to handle errors from those
functions and roll back all changes on failure.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We use mapping to save and restore the tunnel options.
Save also the tunnel options mask.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In notify HW (ring doorbell) flow, we set the bit to request a completion
on the TX descriptor.
When doing so, we should not unset other bits in the same byte.
Currently, this does not fix a real issue, as we still don't have a flow
where both MLX5_WQE_CTRL_CQ_UPDATE and any adjacent bit are set together.
Fixes: 542578c679 ("net/mlx5e: Move helper functions to a new txrx datapath header")
Fixes: 864b2d7153 ("net/mlx5e: Generalize tx helper functions for different SQ types")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the SA handle is created and managed as part of the common
code for different IPsec supporting HW, this handle is passed to HW
to be used on Rx to identify the SA handle that was used to
return the xfrm state to stack.
The above implementation pose a limitation on managing this handle.
Refactor by moving management of this field to the specific HW code.
Downstream patches will introduce the Connect-X support for IPsec that
will use this handle differently than current implementation.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current HW counters are supported only by Innova, split the ipsec
stats group into two groups, one for HW and one for SW. And expose
the HW counters to ethtool only if Innova HW is used for IPsec offload.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the FPGA IPsec is the only hw implementation of the IPsec
acceleration api, and so the mlx5_accel_esp_create_hw_context was
wrongly made to suit this HW api, among other in its parameter list
and some of its parameter endianness.
This implementation might not be suitable for different HW.
Refactor by group and pass all function arguments of
mlx5_accel_esp_create_hw_context in common mlx5_accel_esp_xfrm_attrs
struct field of mlx5_accel_esp_xfrm struct and correct the endianness
according to the HW being called.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Grygorii Strashko