Offload IP header checksum to NIC.
This fixes a previous patch which disabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting disabled for IPv4 pkts. And HW is dropping these pkts
for some reason.
Without this patch, IPv4 TSO appears to be broken:
WIthout this patch I get ~16kbyte/s, with patch close to 2mbyte/s
when copying files via scp from test box to my home workstation.
Looking at tcpdump on sender it looks like hardware drops IPv4 TSO skbs.
This patch restores performance for me, ipv6 looks good too.
Fixes: fa6d7cb5d7 ("net: thunderx: Fix TCP/UDP checksum offload for IPv6 pkts")
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one extraneous level of indentation on assignment statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't offload IP header checksum to NIC.
This fixes a previous patch which enabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting enabled for IPv6 pkts. And HW is dropping these pkts
as it assumes the pkt is IPv4 when IP csum offload is set
in the SQ descriptor.
Fixes: 3a9024f52c ("net: thunderx: Enable TSO and checksum offloads for ipv6")
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We accidentally return success if lio_vf_rep_modinit() fails instead of
propogating the error code.
Fixes: e20f469660 ("liquidio: synchronize VF representor names with NIC firmware")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an error in memory allocation/freeing in
ThunderX PF driver.
I moved the allocation to the probe() function and made it managed.
>From the Colin's email:
While running static analysis on linux-next with CoverityScan I found 3
double free errors in the Cavium thunder driver.
The issue occurs on the err_disable_device: label of function nic_probe
when nic_free_lmacmem(nic) is called and a double free occurs on
nic->duplex, nic->link and nic->speed. This occurs when nic_init_hw()
fails:
/* Initialize hardware */
err = nic_init_hw(nic);
if (err)
goto err_release_regions;
nic_init_hw() calls nic_get_hw_info() and this calls nic_free_lmacmem()
if any of the allocations fail. This free'ing occurs again by the call
to nic_free_lmacmem() on the err_release_regions exit path in nic_probe().
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->rx_dropped was including packets dropped by napi_gro_receive.
If a packet is dropped by network stack, it should not be counted under
driver Rx dropped.
Made necessary changes to not include network stack drops under
netdev->rx_dropped.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Return success if the same dispatch function is being registered for
a given opcode and subcode, there by allow multiple switchdev enable
and disables.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LiquidIO firmware supports a vswitch that needs to know the names of the
VF representors in the host to maintain compatibility for direct
programming using external Openflow agents. So, for each VF representor,
send its name to the firmware when it gets registered and when its name
changes.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zero value assigned to inst_processed at the end of each
iteration of the do-while loop is overwritten on the next iteration
and hence it is a redundant assignment and can be removed. Cleans
up clang warning:
drivers/net/ethernet/cavium/liquidio/request_manager.c:480:3:
warning: Value stored to 'inst_processed' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment to pointer msg is redundant as it is never read, so
remove msg. Also remove the first assignment to qset as this is not
read before the next re-assignment of a new value to qset in the
for-loop. Cleans up two clang warnings:
drivers/net/ethernet/cavium/thunder/nic_main.c:589:2: warning: Value
stored to 'msg' is never read
drivers/net/ethernet/cavium/thunder/nic_main.c:611:2: warning: Value
stored to 'qset' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable and disable switchdev on SRIOV capable LiquidIO NIC with devlink.
Create representor netdev for each SRIOV VF function on SRIOV enable and
and do the cleanup on SRIOV disable.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable switchdev for SRIOV capable LiquidIO NIC. It registers
a representor netdev (with switchdev_ops) for each SRIOV VF created.
It also has changes to send representor interface configurations like
admin state and MTU to LiquidIO firmware and to retrieve HW counted
VF stats for VF representor.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a macvtap interface with the liquidio VF driver as lower device
causes this alarming message to show up in dmesg:
liquidio_link_ctrl_cmd_completion Unknown cmd 27
That's actually a false alarm because cmd 27 is the value of the macro
OCTNET_CMD_SET_UC_LIST which is known. It's a control command sent from
host to NIC firmware to set the unicast MAC address list of the macvtap
lower device.
Make the false alarm go away by adding a case for OCTNET_CMD_SET_UC_LIST
in liquidio_link_ctrl_cmd_completion().
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing ifconfig down on VF driver in the middle of receiving line rate
traffic causes a kernel panic:
LiquidIO_VF 0000:02:00.3: should not come here should not get rx when poll mode = 0 for vf
BUG: unable to handle kernel NULL pointer dereference at (null)
.
.
.
Call Trace:
<IRQ>
? tasklet_action+0x102/0x120
__do_softirq+0x91/0x292
irq_exit+0xb6/0xc0
do_IRQ+0x4f/0xd0
common_interrupt+0x93/0x93
</IRQ>
RIP: 0010:cpuidle_enter_state+0x142/0x2f0
RSP: 0018:ffffffffa6403e20 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff59
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 000000000000001f
RDX: 0000000000000000 RSI: 000000002ab7519f RDI: 0000000000000000
RBP: ffffffffa6403e58 R08: 0000000000000084 R09: 0000000000000018
R10: ffffffffa6403df0 R11: 00000000000003c7 R12: 0000000000000003
R13: ffffd27ebd806800 R14: ffffffffa64d40d8 R15: 0000007be072823f
cpuidle_enter+0x17/0x20
call_cpuidle+0x23/0x40
do_idle+0x18c/0x1f0
cpu_startup_entry+0x64/0x70
rest_init+0xa5/0xb0
start_kernel+0x45e/0x46b
x86_64_start_reservations+0x24/0x26
x86_64_start_kernel+0x6f/0x72
secondary_startup_64+0xa5/0xa5
Code: Bad RIP value.
RIP: (null) RSP: ffff9246ed003f28
CR2: 0000000000000000
---[ end trace 92731e80f31b7d7d ]---
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: 0x24000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
---[ end Kernel panic - not syncing: Fatal exception in interrupt
Reason is: in the function assigned to net_device_ops->ndo_stop, the steps
for bringing down the interface are done in the wrong order. The step that
notifies the NIC firmware to stop forwarding packets to host is done too
late. Fix it by moving that step to the beginning.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer ringing the Tx doorbell if skb->xmit_more is set unless the Tx queue
is full or stopped. To keep latency low, use a deferral limit of 8
packets. We chose 8 because Octeon can fetch at most 8 packets in a single
PCI read, and our tests show that 8 results in low latency.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deprecate the 1-bit flag (bit 2 in the SLI_SCRATCH_1 Octeon register) that
indicates that the liquidio watchdog kernel thread is running for this NIC.
Reason is: it is incompatible with the firmware's use for SLI_SCRATCH_1.
In lieu of checking that now-deprecated flag, check the value of
oct_dev->adapter_refcount to determine whether or not to create the
watchdog kernel thread.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass date and time information to NIC at the time of loading
firmware and periodically update the host time to NIC firmware.
This is to make NIC firmware use the same time reference as Host,
so that it is easy to correlate logs from firmware and host for debugging.
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NULL check before freeing functions like kfree is not needed.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While experimenting with changes to the timekeeping code, I
ran into a build error in the liquidio driver:
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'liquidio_ptp_settime':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1850:22: error: passing argument 1 of 'timespec_to_ns' from incompatible pointer type [-Werror=incompatible-pointer-types]
The driver had a type mismatch since it was first merged, but
this never caused problems because it is only built on 64-bit
architectures that define timespec and timespec64 to the same
type.
If we ever want to compile-test the driver on 32-bit or change
the way that 64-bit timespec64 is defined, we need to fix it,
so let's just do it now.
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
Fix crash in linux PF driver when BARs have been cleared/de-programmed;
fail early init (prior to mapping BARs) if the BAR0 or
BAR1 registers are zero.
This situation can arise when the PF is added to a VM (PCI pass-through),
then a PF FLR is issued (in the VM). After this occurs, the BAR registers
will be zero. If we attempt to load the PF driver in the host
(after VM has been shutdown), the host can reset.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct call_single_data is used in IPIs to transfer information between
CPUs. Its size is bigger than sizeof(unsigned long) and less than
cache line size. Currently it is not allocated with any explicit alignment
requirements. This makes it possible for allocated call_single_data to
cross two cache lines, which results in double the number of the cache lines
that need to be transferred among CPUs.
This can be fixed by requiring call_single_data to be aligned with the
size of call_single_data. Currently the size of call_single_data is the
power of 2. If we add new fields to call_single_data, we may need to
add padding to make sure the size of new definition is the power of 2
as well.
Fortunately, this is enforced by GCC, which will report bad sizes.
To set alignment requirements of call_single_data to the size of
call_single_data, a struct definition and a typedef is used.
To test the effect of the patch, I used the vm-scalability multiple
thread swap test case (swap-w-seq-mt). The test will create multiple
threads and each thread will eat memory until all RAM and part of swap
is used, so that huge number of IPIs are triggered when unmapping
memory. In the test, the throughput of memory writing improves ~5%
compared with misaligned call_single_data, because of faster IPIs.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Huang, Ying <ying.huang@intel.com>
[ Add call_single_data_t and align with size of call_single_data. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/87bmnqd6lz.fsf@yhuang-mobile.sh.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the NIC firmware, the 1-bit flag indicating "firmware is loaded" moved
from SLI_SCRATCH_1 to SLI_SCRATCH_2 (these are Octeon general-purpose
scratch registers). Make the PF driver conform to this change.
Remove code that sets the "firmware is loaded" flag because it's now the
firmware's job to do that.
In the code that detects whether or not the firmware is loaded, don't just
rely on checking the "firmware is loaded" flag because that may cause a
rare false negative. Add code that deduces whether or not the firmware is
loaded; that will never give a false negative.
Also bump up driver version to match newer NIC firmware.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro LIO_CMD_WAIT_TM is not specific to the PF driver; it can be used
by the VF driver too, so move its definition from a PF-specific header file
to one that's common to PF and VF.
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix problem when PF is used in pass-through mode in a VM (w/embedded f/w).
If host error reading PF num from CN23XX_PCIE_SRIOV_FDL reg,
try to retrieve PF num from SLI_PKT(0)_INPUT_CONTROL (initialized by f/w).
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Smatch error by not dereferencing iq pointer if it's NULL.
See http://marc.info/?l=kernel-janitors&m=150296723301129&w=2
Also, remove unnecessary parentheses.
Fixes: d314ac2228 ("liquidio: moved liquidio_napi_poll to lio_core.c")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Issue credits BEFORE enabling DROQ's; this prevents PKTPF_ERR interrupt.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add support for PF FLR when exiting
(enables CORE_DRV_ACTIVE upon next driver init)
2. Skip some initialization (don't try to load f/w, activate consoles).
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VF's MTU is capped at the parent PF's MTU. So if there's a change in the
PF's MTU, then update the VF's netdev->max_mtu.
Also remove duplicate log messages for MTU change.
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adding support for ethtool --set-channels feature
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal