On OMAP2420-based systems, the PM code ignores the state of the UART
functional clocks when determining what idle state to enter. This
breaks the serial port now that the UART driver's clock behavior can
be controlled via the PM autosuspend timeout.
To fix, remove the special-case idle handling for the UARTs in the
OMAP2420/2430 PM idle code added by commit
4af4016c53 ("OMAP3: PM: UART: disable
clocks when idle and off-mode support").
Tested on Nokia N800. This patch is a collaboration between Tony
Lindgren <tony@atomide.com> and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.
The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.
This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KZgACgkQMUfUDdst+yk0HgCeIdU3VTWqdxZDXp3G1sFIXZ1b
47YAnRAMAar+/aLaNhqGrcz7aa5y2cUU
=8sr8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM kernel uses undefined instructions to implement
BUG/BUG_ON(). This leads to problems where people don't read one
line above the Oops message and see the "kernel BUG at ..."
message and so they wrongly assume the kernel has hit an
undefined instruction.
Instead of printing:
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP
print
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
This should prevent people from thinking the BUG_ON was an
undefined instruction when it was actually intentional.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
armv7's flush_cache_all() flushes caches via set/way. To
determine the cache attributes (line size, number of sets,
etc.) the assembly first writes the CSSELR register to select a
cache level and then reads the CCSIDR register. The CSSELR register
is banked per-cpu and is used to determine which cache level CCSIDR
reads. If the task is migrated between when the CSSELR is written and
the CCSIDR is read the CCSIDR value may be for an unexpected cache
level (for example L1 instead of L2) and incorrect cache flushing
could occur.
Disable interrupts across the write and read so that the correct
cache attributes are read and used for the cache flushing
routine. We disable interrupts instead of disabling preemption
because the critical section is only 3 instructions and we want
to call v7_dcache_flush_all from __v7_setup which doesn't have a
full kernel stack with a struct thread_info.
This fixes a problem we see in scm_call() when flush_cache_all()
is called from preemptible context and sometimes the L2 cache is
not properly flushed out.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With an admittedly exotic choice of configuration options
(CC_OPTIMIZE_FOR_SIZE, THUMB2, some other size-minimizing ones)
and compiler, the proc_info table can end up being misaligned,
and the kernel being unbootable (Error: unrecognized/unsupported
processor variant).
Forcing the alignement to 4 bytes in the linker script fixes the
issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit db0d4db22a ('ARM: gic: allow GIC to support non-banked setups)
requires a cpu-offset property to be specified for non-banked gic
controllers, which is the case for Exynos4.
Reported-and-Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This commit brings exynos4-dt in line with recent changes to
mach-exynos tree, specifically:
- Fixes build break related to replacing plat/exynos4.h with
common.h in commit cc511b8d84 ("ARM: 7257/1: EXYNOS:
introduce arch/arm/mach-exynos/common.[ch]")
- Converts machine to use CONFIG_MULTI_IRQ_HANDLER as done for
other machines in commit 4e44d2cb95 ("ARM: exynos4: convert
to CONFIG_MULTI_IRQ_HANDLER")
- Adds restart specifier as done for other machines in commit
9eb4859564 ("ARM: 7262/1: restart: EXYNOS: use new restart hook")
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For L1 instruction cache and L2 cache the shared CPU information
is wrong. On current AMD family 15h CPUs those caches are shared
between both cores of a compute unit.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=42607
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Petkov Borislav <Borislav.Petkov@amd.com>
Cc: Dave Jones <davej@redhat.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120208195229.GA17523@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xeae8):
Section mismatch in reference from the function cm_t35_init_usbh()
to the (unknown reference) .init.data:(unknown)
The function cm_t35_init_usbh() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_init_usbh lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the latest Sourcery G++ Lite 2011.03-41 and latest linaro
tool-chains OMAP2 only build breaks with below error.
arch/arm/mach-omap2/omap-smc.S: Assembler messages:
arch/arm/mach-omap2/omap-smc.S:30: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:53: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:61: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:69: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:77: Error: selected processor does not support ARM mode `smc #0'
make[1]: *** [arch/arm/mach-omap2/omap-smc.o] Error 1
OMAP2 devices doesn't have the security support but the security support
was getting built because of OMAP2PLUS. Don't build security code for
OMAP2 devices.
While at it, fix the secure-common line in the Makefile to use tabs
instead of spaces.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
Kevin Cernekee reported that recent cleanup
that replaced pci_iomap with a generic function
failed to take into account the differences
in io port handling on mips and sh architectures.
Rather than revert the changes reintroducing the
code duplication, this patchset fixes this
by adding ability for architectures to override
ioport mapping for pci devices.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPL9X8AAoJECgfDbjSjVRpgzgIAIQGeWIP0JUWDDhLfYscTBZx
96Am+8+maVl12t+evVH8lMnJDSqjKH0kWxk6CTQSUo57gZ4ne1SxbZ0+s5DcsE6m
XAnIvkA+4pw36l4QRkEj8g+yrhpQhqaiKJt/l80jaVFGVAw47WrxGKatUe9L90lI
X7+xa/F5zvZO6oamEI94SAojIvmKkZfHIjGc/NaZLaWHRysdFf8Ek13mj2+9FLq3
dxmg9F14eS2X59tIkN4BLM4Dq8UyZqraT0N/0bO0Tetqx0azzNZbsBsg5RwQ15IF
Ei0dMFARoT9UcIpdSwtpGGCoqYa5yRHFT1g54hv/Pon0mKUjG7Fpz5LRWmZ5Xic=
=b1R2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
arch: fix ioport mapping on mips,sh
Kevin Cernekee reported that recent cleanup that replaced pci_iomap with
a generic function failed to take into account the differences in io
port handling on mips and sh architectures.
Rather than revert the changes reintroducing the code duplication, this
patchset fixes this by adding ability for architectures to override
ioport mapping for pci devices.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
sh: use the the PCI channels's io_map_base
mips: use the the PCI controller's io_map_base
lib: add NO_GENERIC_PCI_IOPORT_MAP
The following patch fixes a bug introduced by the following
commit:
e050e3f0a7 ("perf: Fix broken interrupt rate throttling")
The patch caused the following warning to pop up depending on
the sampling frequency adjustments:
------------[ cut here ]------------
WARNING: at arch/x86/kernel/cpu/perf_event.c:995 x86_pmu_start+0x79/0xd4()
It was caused by the following call sequence:
perf_adjust_freq_unthr_context.part() {
stop()
if (delta > 0) {
perf_adjust_period() {
if (period > 8*...) {
stop()
...
start()
}
}
}
start()
}
Which caused a double start and a double stop, thus triggering
the assert in x86_pmu_start().
The patch fixes the problem by avoiding the double calls. We
pass a new argument to perf_adjust_period() to indicate whether
or not the event is already stopped. We can't just remove the
start/stop from that function because it's called from
__perf_event_overflow where the event needs to be reloaded via a
stop/start back-toback call.
The patch reintroduces the assertion in x86_pmu_start() which
was removed by commit:
84f2b9b ("perf: Remove deprecated WARN_ON_ONCE()")
In this second version, we've added calls to disable/enable PMU
during unthrottling or frequency adjustment based on bug report
of spurious NMI interrupts from Eric Dumazet.
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: markus@trippelsdorf.de
Cc: paulus@samba.org
Link: http://lkml.kernel.org/r/20120207133956.GA4932@quad
[ Minor edits to the changelog and to the code ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stephane Eranian reported that doing a scheduler latency
measurements with perf on AMD doesn't work out as expected due
to the fact that the sched_clock() granularity is too coarse,
i.e. done in jiffies due to the sched_clock_stable not set,
which, if set, would mean that we get to use the TSC as sample
source which would give us much higher precision.
However, there's no reason not to set sched_clock_stable on AMD
because all families from F10h and upwards do have an invariant
TSC and have the CPUID flag to prove (CPUID_8000_0007_EDX[8]).
Make it so, #1.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Venki Pallipadi <venki@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/r/20120206132546.GA30854@quad
[ Should any non-standard system break the TSC, we should
mark them so explicitly, in their platform init handler, or
in a DMI quirk. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AMD processors will never support /dev/cpu/microcode updating so
just silently fail instead of printing out a warning for every
cpu.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1328552935-965-1-git-send-email-prarit@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UARTC is connected to the mini-pcie port.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
If the SG bit is set in MMUTR the page is accessible for all
userspace processes (ignoring the ASID). So a process might randomly
access a page from a different process which had a shared page
(from shared memory) in its context.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
We had problems accessing our NOR flash trough mtd. The system always got
stuck at attaching UBI using ubiattach if booted from NFS or after mounting
squashfs as rootfs directly from NOR flash.
After some testing of the new changes introduced from v3.2-rc1 to v3.2-rc7
we had to apply the following patch to get mtd working again.
[gerg: The problem was ultimately caused by allocated kernel pages not having
the shared (SG) bit set. Without the SG bit set the MMU will look for page
matches incorporating the ASID as well. Things like module regions allocated
using vmalloc would fault when other processes run. ]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The return path from an exception was checking too many bits in the
thread_info->flags, and getting stuck calling do_signal(). There was
no work to do, we should only be checking the low 8 bits (as per comments
and definitions in arch/m68k/include/asm/thread_info.h).
This fixes the stuck process problem when using strace.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fixing a regression with the PMU MSRs when PMU virtualization is
disabled, a guest-internal DoS with the SYSCALL instruction, and a dirty
memory logging race that may cause live migration to fail.
* 'kvm-updates/3.3' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: do not #GP on perf MSR writes when vPMU is disabled
KVM: x86: fix missing checks in syscall emulation
KVM: x86: extend "struct x86_emulate_ops" with "get_cpuid"
KVM: Fix __set_bit() race in mark_page_dirty() during dirty logging
So that we can get the perf bench exec stack fixes and then apply the
remaining fix for the files added after what is in perf/urgent.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* 'v3.3-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
ARM: S5PV210: Fix the name of exynos4_clk_hdmiphy_ctrl() for S5PV210
ARM: EXYNOS: Remove build warning without enabling PM
ARM: SAMSUNG: Fix platform data setup for I2C adapter 0
ARM: EXYNOS: fix non-SMP builds for EXYNOS4
ARM: S3C6410: Use device names for both I2C clocks
ARM: S3C64XX: Make s3c64xx_init_uarts() static
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tFsG
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcmring: fix build failure in mach-bcmring/arch.c
ARM: bcmring: remove unused DMA map code
ARM: davinci: update mdio bus name
ARM: OMAP2+: arch/arm/mach-omap2/smartreflex.c: add missing iounmap
ARM: OMAP2+: arch/arm/mach-omap2/devices.c: introduce missing kfree
ARM: OMAP: fix MMC2 loopback clock handling
ARM: OMAP: fix erroneous mmc2 clock change on mmc3 setup
ARM: OMAP2+: GPMC: fix device size setup
ARM: OMAP2+: timer: Fix crash due to wrong arg to __omap_dm_timer_read_counter
ARM: OMAP3: hwmod data: register dss hwmods after dss_core
ARM: OMAP2/3: PRM: fix missing plat/irqs.h build breakage
ARM: OMAP2+: io: fix compilation breakage on 2420-only configs
ARM: OMAP4: hwmod data: Add names for DMIC memory address space
ARM: OMAP3: hwmod data: add SYSC_HAS_ENAWAKEUP for dispc
ARM: OMAP2+: hwmod data: split omap2/3 dispc hwmod class
ARM: davinci: DA850: remove non-existing pll1_sysclk4-7 clocks
ARM: OMAP2: fix regulator warnings
ARM: OMAP2: fix omap3 touchbook kconfig warning
i2c: OMAP: Fix OMAP1 build error
Upstream commit d1fce9c115
"ARM: restart: bcmring: use new restart hook"
breaks building of this platform, since what used to be the
last field of the MACHINE_START/END block didn't have a
trailing comma. Once another field was added below, we get:
arch/arm/mach-bcmring/arch.c:198: error: request for member 'restart' in something not a structure or union
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove BCMRING DMA map code which is no longer used.
This also fixes a build error with dma.c introduced by
bfcd2ea6a4.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
i.MX SDMA: Fix burstsize settings
ARM: mach-shmobile: both USB DMAC instances on sh7372 are slave-only
dma: sh_dma: not all SH DMAC implementations support MEMCPY
at_hdmac: bugfix for enabling channel irq
dmaengine: fix missing 'cnt' in ?: in dmatest
Enable use of the generic atomic64 implementation on AVR32 platforms.
Without this the kernel fails to build as the architecture does not
provide its version.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Defining memscan() as memchr() is wrong, because the return values of
memscan() and memchr() are different when the character is not found. So
use the generic memscan() implementation to fix this.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a user offlines a VCPU and then onlines it, we get:
NMI watchdog disabled (cpu2): hardware events not enabled
BUG: scheduling while atomic: swapper/2/0/0x00000002
Modules linked in: dm_multipath dm_mod xen_evtchn iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi scsi_mod libcrc32c crc32c radeon fbco
ttm bitblit softcursor drm_kms_helper xen_blkfront xen_netfront xen_fbfront fb_sys_fops sysimgblt sysfillrect syscopyarea xen_kbdfront xenfs [last unloaded:
Pid: 0, comm: swapper/2 Tainted: G O 3.2.0phase15.1-00003-gd6f7f5b-dirty #4
Call Trace:
[<ffffffff81070571>] __schedule_bug+0x61/0x70
[<ffffffff8158eb78>] __schedule+0x798/0x850
[<ffffffff8158ed6a>] schedule+0x3a/0x50
[<ffffffff810349be>] cpu_idle+0xbe/0xe0
[<ffffffff81583599>] cpu_bringup_and_idle+0xe/0x10
The reason for this should be obvious from this call-chain:
cpu_bringup_and_idle:
\- cpu_bringup
| \-[preempt_disable]
|
|- cpu_idle
\- play_dead [assuming the user offlined the VCPU]
| \
| +- (xen_play_dead)
| \- HYPERVISOR_VCPU_off [so VCPU is dead, once user
| | onlines it starts from here]
| \- cpu_bringup [preempt_disable]
|
+- preempt_enable_no_reschedule()
+- schedule()
\- preempt_enable()
So we have two preempt_disble() and one preempt_enable(). Calling
preempt_enable() after the cpu_bringup() in the xen_play_dead
fixes the imbalance.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
__kuser_cmpxchg64 has a return path using bx lr to get back to the caller.
This is actually ok since the code in question is predicated on
CONFIG_CPU_32v6K, but for the sake of consistency using the usr_ret
macro is probably better.
Acked-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the new throttling/unthrottling code introduced with
commit:
e050e3f0a7 ("perf: Fix broken interrupt rate throttling")
we occasionally hit two WARN_ON_ONCE() checks in:
- intel_pmu_pebs_enable()
- intel_pmu_lbr_enable()
- x86_pmu_start()
The assertions are no longer problematic. There is a valid
path where they can trigger but it is harmless.
The assertion can be triggered with:
$ perf record -e instructions:pp ....
Leading to paths:
intel_pmu_pebs_enable
intel_pmu_enable_event
x86_perf_event_set_period
x86_pmu_start
perf_adjust_freq_unthr_context
perf_event_task_tick
scheduler_tick
And:
intel_pmu_lbr_enable
intel_pmu_enable_event
x86_perf_event_set_period
x86_pmu_start
perf_adjust_freq_unthr_context.
perf_event_task_tick
scheduler_tick
cpuc->enabled is always on because when we get to
perf_adjust_freq_unthr_context() the PMU is not totally
disabled. Furthermore when we need to adjust a period,
we only stop the event we need to change and not the
entire PMU. Thus, when we re-enable, cpuc->enabled is
already set. Note that when we stop the event, both
pebs and lbr are stopped if necessary (and possible).
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/20120202110401.GA30911@quad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bugs, x86: Fix printk levels for panic, softlockups and stack dumps
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Fix number of samples displayed
perf tools: Fix strlen() bug in perf_event__synthesize_event_type()
perf tools: Fix broken build by defining _GNU_SOURCE in Makefile
x86/dumpstack: Remove unneeded check in dump_trace()
perf: Fix broken interrupt rate throttling
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt: Fix task stack corruption under __ARCH_WANT_INTERRUPTS_ON_CTXSW
sched: Fix ancient race in do_exit()
sched/nohz: Fix nohz cpu idle load balancing state with cpu hotplug
sched/s390: Fix compile error in sched/core.c
sched: Fix rq->nr_uninterruptible update race
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/reboot: Remove VersaLogic Menlow reboot quirk
x86/reboot: Skip DMI checks if reboot set by user
x86: Properly parenthesize cmpxchg() macro arguments
Linux uses two PMD entries for a PTE with the classic page table format,
covering 2MB range. However, the __pte_free_tlb() function only adds a
single TLB flush corresponding to 1MB range covering 'addr'. On
Cortex-A15, level 1 entries can be cached by the TLB independently of
the level 2 entries and without additional flushing a PMD entry would be
left pointing at the wrong PTE. The patch limits the TLB flushing range
to two 4KB pages around the 1MB boundary within PMD.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 89d6c0b5 ("perf, arch: Add generic NODE cache events") added
empty NODE event definitions for the ARM PMU implementations. This was
merged along with Cortex-A5 and Cortex-A15 PMU support, so they missed
out on the original patch.
This patch adds the empty definitions to Cortex-A5 and Cortex-A15.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we are context switched whilst copying into a thread's
vfp_hard_struct then the partial copy may be corrupted by the VFP
context switching code (see "ARM: vfp: flush thread hwstate before
restoring context from sigframe").
This patch updates the ptrace VFP set code so that the thread state is
flushed before the copy, therefore disabling VFP and preventing
corruption from occurring.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In a preemptible kernel, vfp_set() can be preempted, causing the
hardware VFP context to be switched while the thread vfp state is
being read and modified. This leads to a race condition which can
cause the thread vfp state to become corrupted if lazy VFP context
save occurs due to preemption in between the time thread->vfpstate
is read and the time the modified state is written back.
This may occur if preemption occurs during the execution of a
ptrace() call which modifies the VFP register state of a thread.
Such instances should be very rare in most realistic scenarios --
none has been reported, so far as I am aware. Only uniprocessor
systems should be affected, since VFP context save is not currently
lazy in SMP kernels.
The problem was introduced by my earlier patch migrating to use
regsets to implement ptrace.
This patch does a vfp_sync_hwstate() before reading
thread->vfpstate, to make sure that the thread's VFP state is not
live in the hardware registers while the registers are modified.
Thanks to Will Deacon for spotting this.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Following execution of a signal handler, we currently restore the VFP
context from the ucontext in the signal frame. This involves copying
from the user stack into the current thread's vfp_hard_struct and then
flushing the new data out to the hardware registers.
This is problematic when using a preemptible kernel because we could be
context switched whilst updating the vfp_hard_struct. If the current
thread has made use of VFP since the last context switch, the VFP
notifier will copy from the hardware registers into the vfp_hard_struct,
overwriting any data that had been partially copied by the signal code.
Disabling preemption across copy_from_user calls is a terrible idea, so
instead we move the VFP thread flush *before* we update the
vfp_hard_struct. Since the flushing is performed lazily, this has the
effect of disabling VFP and clearing the CPU's VFP state pointer,
therefore preventing the thread from being updated with stale data on
the next context switch.
Cc: stable <stable@vger.kernel.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 3c424f3598.
Joachim Eastwood reports:
| "ARM: 7304/1: ioremap: fix boundary check when reusing static mapping"
| Commit: 3c424f3598 in Linus master
|
| Breaks booting on my custom AT91RM9200 board.
| There isn't any error messages or anything that indicates what goes
| wrong it just stops after; Uncompressing Linux... done, booting the
| kernel.
|
| Reverting it makes my board boot again.
and further debugging reveals:
ioremap: pfn=fffff phys=fffff000 offset=400 size=1000
ioremap: area c3ffdfc0: phys_addr=200000 pfn=200 size=4000
ioremap: found: addr fef74000 => fed73000 => fed73400
Clearly, an area for pfn 0x200, 16K can't ever satisfy a request for pfn
0xfffff. This happens because the changed if statement becomes:
if (0x00200 > 0xfffff ||
0xfffff000 + 0x400 + 0x1000-1 > 0x00200000 + 0x4000-1)
and therefore:
if (0x00200 > 0xfffff ||
0x000003ff > 0x00203fff)
The if condition fails, and so we _believe_ that the SRAM mapping fits
our request. Clearly that's totally bogus.
Moreover, the original premise of the 'fix' patch was wrong:
| The condition checking boundaries of the requested and existing
| mappings didn't take in-page offset into consideration though,
| which lead to obscure and hard to debug problems when requested
| mapping crossed end of the static one.
as the code immediately above this loop does:
size = PAGE_ALIGN(offset + size);
so 'size' already contains the requested offset into the page.
So, revert the broken 'fix'.
Acked-by: Nicolas Pitre <nico@linaro.org>
Both sparc 32-bit's software divide assembler and MPILIB provide
clz_tab[] with identical contents.
Break it out into a seperate object file and select it when
SPARC32 or MPILIB is set.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Morris <jmorris@namei.org>
Return to behaviour perf MSR had before introducing vPMU in case vPMU
is disabled. Some guests access those registers unconditionally and do
not expect it to fail.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On hosts without this patch, 32bit guests will crash (and 64bit guests
may behave in a wrong way) for example by simply executing following
nasm-demo-application:
[bits 32]
global _start
SECTION .text
_start: syscall
(I tested it with winxp and linux - both always crashed)
Disassembly of section .text:
00000000 <_start>:
0: 0f 05 syscall
The reason seems a missing "invalid opcode"-trap (int6) for the
syscall opcode "0f05", which is not available on Intel CPUs
within non-longmodes, as also on some AMD CPUs within legacy-mode.
(depending on CPU vendor, MSR_EFER and cpuid)
Because previous mentioned OSs may not engage corresponding
syscall target-registers (STAR, LSTAR, CSTAR), they remain
NULL and (non trapping) syscalls are leading to multiple
faults and finally crashs.
Depending on the architecture (AMD or Intel) pretended by
guests, various checks according to vendor's documentation
are implemented to overcome the current issue and behave
like the CPUs physical counterparts.
[mtosatti: cleanup/beautify code]
Signed-off-by: Stephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In order to be able to proceed checks on CPU-specific properties
within the emulator, function "get_cpuid" is introduced.
With "get_cpuid" it is possible to virtually call the guests
"cpuid"-opcode without changing the VM's context.
[mtosatti: cleanup/beautify code]
Signed-off-by: Stephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
commit 43db595e8b
(sh: switch to GENERIC_PCI_IOMAP)
failed to take into account the PCI channels's
io_map_base for mapping IO BARs.
This also caused a new warning on sh.
Fix this, without re-introducing code duplication,
by setting NO_GENERIC_PCI_IOPORT_MAP
and supplying a sh-specific __pci_ioport_map.
Reported-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit eab90291d3
(mips: switch to GENERIC_PCI_IOMAP)
failed to take into account the PCI controller's
io_map_base for mapping IO BARs.
This also caused a new warning on mips.
Fix this, without re-introducing code duplication,
by setting NO_GENERIC_PCI_IOPORT_MAP
and supplying a mips-specific __pci_ioport_map.
Reported-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit d761f0c521.
Patch: "cpu: Register a generic CPU device on architectures that currently do not"
(sha1: 9f13a1fd45)
selects GENERIC_CPU_DEVICES for Microblaze which register cpu.
My patch was done in the same time that's why cpu was registered twice which
caused this warning log:
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:481 sysfs_add_one+0xb0/0xdc()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu0'
Modules linked in:
...
Signed-off-by: Michal Simek <monstr@monstr.eu>
In order to keep the sensor's master clock frequency in valid range
when FIMC parent clock is xusbxti, the specified frequency must be
exactly 24MHZ, otherwise it's being set to too low value due to
rounding.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The real LCD resolution on Nuri is 1024x600, not 1280x800. This change
fixes the color distortion (green shadows) on half of the screen.
Also increase framebuffer virtual size for display panning support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] dasd: revalidate server for new pathgroup
[S390] dasd: revert LCU optimization
[S390] cleanup entry point definition
This commit removes the reboot quirk originally added by commit
e19e074 ("x86: Fix reboot problem on VersaLogic Menlow boards").
Testing with a VersaLogic Ocelot (VL-EPMs-21a rev 1.00 w/ BIOS
6.5.102) revealed the following regarding the reboot hang
problem:
- v2.6.37 reboot=bios was needed.
- v2.6.38-rc1: behavior changed, reboot=acpi is needed,
reboot=kbd and reboot=bios results in system hang.
- v2.6.38: VersaLogic patch (e19e074 "x86: Fix reboot problem on
VersaLogic Menlow boards") was applied prior to v2.6.38-rc7. This
patch sets a quirk for VersaLogic Menlow boards that forces the use
of reboot=bios, which doesn't work anymore.
- v3.2: It seems that commit 660e34c ("x86: Reorder reboot method
preferences") changed the default reboot method to acpi prior to
v3.0-rc1, which means the default behavior is appropriate for the
Ocelot. No VersaLogic quirk is required.
The Ocelot board used for testing can successfully reboot w/out
having to pass any reboot= arguments for all 3 current versions
of the BIOS.
Signed-off-by: Michael D Labriola <michael.d.labriola@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Michael D Labriola <mlabriol@gdeb.com>
Cc: Kushal Koolwal <kushalkoolwal@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/87vcnub9hu.fsf@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Skip DMI checks for vendor specific reboot quirks if the user
passed in a reboot= arg on the command line - we should never
override user choices.
Signed-off-by: Michael D Labriola <michael.d.labriola@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michael D Labriola <mlabriol@gdeb.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/87wr8ab9od.fsf@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'stable/for-linus-fixes-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/granttable: Disable grant v2 for HVM domains.
x86: xen: size struct xen_spinlock to always fit in arch_spinlock_t
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm: (31 commits)
ARM: 7304/1: ioremap: fix boundary check when reusing static mapping
ARM: 7301/1: Rename the T() macro to TUSER() to avoid namespace conflicts
ARM: 7299/1: ftrace: clear zero bit in reported IPs for Thumb-2
ARM: 7298/1: realview: fix mapping of MPCore private memory region
PCMCIA: fix sa1111 oops on remove
ARM: 7288/1: mach-sa1100: add missing module_init() call
ARM: 7297/1: smp_twd: make sure timer is stopped before registering it
ARM: 7296/1: proc-v7.S: remove HARVARD_CACHE preprocessor guards
ARM: 7295/1: cortex-a7: move proc_info out of !CONFIG_ARM_LPAE block
ARM: 7293/1: logical_cpu_map: decouple CPU mapping from SMP
ARM: 7291/1: cache: assume 64-byte L1 cachelines for ARMv7 CPUs
ARM: 7290/1: vmlinux.lds.S: align the exception fixup table to a 4-byte boundary
ARM: 7289/1: vmlinux.lds.S: do not hardcode cacheline size as 32 bytes
MFD: ucb1x00-ts: fix resume failure
MFD: ucb1x00-core: fix gpiolib direction_output handling
MFD: ucb1x00-core: fix missing restore of io output data on resume
MFD: mcp-core: fix mcp_priv() to be more type safe
MFD: mcp-core: fix complaints from the genirq layer
Revert "ARM: sa11x0: Implement autoloading of codec and codec pdata for mcp bus."
Revert "ARM: sa1100: Refactor mcp-sa11x0 to use platform resources."
...
Fix up conflict due to arch/arm/mach-mx5/Kconfig having been merged into
mach-imx5 (commit 784a90c0a7d8: "ARM i.MX: Merge i.MX5 support into
mach-imx"), but the ARM_L1_CACHE_SHIFT_6 entry was moved to be driven by
the CPU_V7 logic from it in the old location in rmk's branch (commit
a092f2b15399: "ARM: 7291/1: cache: assume 64-byte L1 cachelines for
ARMv7 CPUs").
AT91 needed reset fixes which resulted in some minor code refactoring,
it also adds a feature-removal for one of their platforms for 3.4.
The USB patches have been acked by Greg K-H.
i.MX and ux500 both have some minor fixes, nothing controversial.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPIlhOAAoJEIwa5zzehBx3l+UP/1LcalLOTEU0bthHNBUoQYEQ
drDqaFlnBsDryuOzbtGGO41jRySqQWQfQTiVThrEpE3ZUH+NLih5cDRk2sUIzdMd
8tFWMN7HJnvaA0LT6ODcnC4HoRUBWieYLrPnjA+rlUPFCY/vJQ5010xFhZs2nGBo
Y5AOQ6Fun/1z5P4V5u+6GzKPPsJZPaCqEPwLJoc5yCJgvfO6RnAFuICv0F183lMh
TYVkZISF3GYdD/wWQZuytYJRj6IB3mV1GCe0q1fRD9E49929mOnC4SZ3gwa3nF4D
9IAJviVq+YtEIwTw4H+DJ+k7NXS7GR+F6hxcCrWygEYlOgFqHlRYIL35pxXWq+Sm
s0jMxC3RdyXmbfhuwi4o607OwMQkwVyNM+N5xUGaww4Inn3Lw6VPaqyQRtW6Bhiz
o/fyuOALFt7FDoLII02BJgFMdoeEV1gfXlTTdiz7yEekE0h9ng0A3VSRQRph3kLn
CScQZyOFGrFFm9UNM0T0FrWlshd+ZU1yQGAdZHIX/Fv/euLNhXDnF2bKxAx7CiTh
wcFezf7vjXjs/iTV+ZsDBe0oKWGmdvxVJksDV6X74DlMfZd9AYi+ntvXzvWrcHdp
C6wmTtePlSbEMem3RhWEQD8EeTy/qwzPRwLVNqlyT7QURhqCgJlbx133gMEt6113
wd95I9VZjKE6KSKh7BsS
=nS4F
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc:
AT91 needed reset fixes which resulted in some minor code refactoring,
it also adds a feature-removal for one of their platforms for 3.4.
The USB patches have been acked by Greg K-H.
i.MX and ux500 both have some minor fixes, nothing controversial.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-imx/mach-mx53_ard.c: add missing iounmap
ARM: imx: iomux-v1.h: Fix build error due to __init annotation
ARM: at91: Fix at91sam9g45 and at91cap9 reset
ARM: at91: make rstc soc independent
ARM: at91: introduce AT91_SAM9_ALT_RESET to select the at91sam9 alternative reset
ARM: at91: merge at91cap9_ddrsdr.h in at91sam9_ddrsdr.h
ARM: at91: fix cap9 ddrsdr register
ARM/USB: at91/ohci-at91: rename vbus_pin_inverted to vbus_pin_active_low
USB: at91: fix clk_get error handling
ARM: at91: removal of CAP9 SoC family
ARM: at91: fix at91rm9200 soc subtype handling
mach-ux500: no MMC_CAP_SD_HIGHSPEED on Snowball
mach-ux500: enable ARM errata 764369
mach-ux500: do not override outer.inv_all
mach-ux500: musb: now musb is always in OTG mode
ARM: imx6: add missing twd_clk for imx6q clock
Smatch complains that we have some inconsistent NULL checking.
If "task" were NULL then it would lead to a NULL dereference
later. We can remove this test because earlier on in the
function we have:
if (!task)
task = current;
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Clemens Ladisch <clemens@ladisch.de>
Link: http://lkml.kernel.org/r/20120128105246.GA25092@elgon.mountain
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since commit 576d2f2525 "ARM: add
generic ioremap optimization by reusing static mappings" ioremap()
is trying to reuse existing static mapping when possible.
The condition checking boundaries of the requested and existing
mappings didn't take in-page offset into consideration though,
which lead to obscure and hard to debug problems when requested
mapping crossed end of the static one.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 5a05a8200a ("davinci_emac:
use an unique MDIO bus name") introduced during the v3.3 merge
window updated the davinci mdio bus name to make it unique.
Update the bus name in board files which use DaVinci MDIO bus
to match the new name. Without this PHY is not detected with
error like:
PHY 0:01 not found
net eth0: could not connect to phy 0:01
Tested on DM365 and DA850 EVMs.
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
* commit 'v3.3-rc1': (9775 commits)
Linux 3.3-rc1
x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
qnx4: don't leak ->BitMap on late failure exits
qnx4: reduce the insane nesting in qnx4_checkroot()
qnx4: di_fname is an array, for crying out loud...
KEYS: Permit key_serial() to be called with a const key pointer
keys: fix user_defined key sparse messages
ima: fix cred sparse warning
uml: fix compile for x86-64
MPILIB: Add a missing ENOMEM check
tpm: fix (ACPI S3) suspend regression
nvme: fix merge error due to change of 'make_request_fn' fn type
xen: using EXPORT_SYMBOL requires including export.h
gpio: tps65910: Use correct offset for gpio initialization
acpi/apei/einj: Add extensions to EINJ from rev 5.0 of acpi spec
intel_idle: Split up and provide per CPU initialization func
ACPI processor: Remove unneeded variable passed by acpi_processor_hotadd_init V2
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
...
* 'fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
mach-ux500: no MMC_CAP_SD_HIGHSPEED on Snowball
mach-ux500: enable ARM errata 764369
mach-ux500: do not override outer.inv_all
mach-ux500: musb: now musb is always in OTG mode
Commit 4a858cfc9a (arm: convert sysdev_class to a regular subsystem)
converted the samsung sysdevs into subsys_interface instances.
While the original add-function only had a (struct sys_device *)
parameter, the dev_add from subsys_interface needs
(struct device *, struct subsys_interface *)
leading to "initialized from incompatible pointer type" warnings.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The new spi-sh driver decodes the IORESOURCE_MEM_TYPE_MASK. So, the
resource needs the IORESOURCE_MEM_32BIT.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix compilation breakage
arch/sh/boards/mach-se/7724/setup.c:182: error: 'V4L2_PIX_FMT_RGB565' undeclared here (not in a function)
make[3]: *** [arch/sh/boards/mach-se/7724/setup.o] Error 1
caused by commit "fbdev: sh_mobile_lcdc: Support FOURCC-based format API"
Also add other missing headers, even if compilation currently succeeds
because of their indirect inclusion via other headers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixed following build warning with exynos4_defconfig.
arch/arm/mach-exynos/clock.c:33: warning: 'exynos4_clock_save' defined but not used
arch/arm/mach-exynos/clock-exynos4210.c:35: warning: 'exynos4210_clock_save' defined but not used
arch/arm/mach-exynos/clock-exynos4212.c:35: warning: 'exynos4212_clock_save' defined but not used
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The common static default_i2c_data structure gets bus_num set by each
s3c_i2c?_set_platdata() call, except for s3c_i2c0_set_platdata(). Thus
if for instance s3c_i2c1_set_platdata() is called prior to
s3c_i2c0_set_platdata() the I2C0 controller has bus_num set to wrong value
of 1, i.e. the one from previous set_platdata call. Fix this by also setting
bus_num for I2C0.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following build issue, which happens only if
SMP has been disabled:
arch/arm/mach-exynos/built-in.o: In function `exynos4_pm_resume':
arch/arm/mach-exynos/pm.c:387: undefined reference to `scu_enable'
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When the S3C64xx CPUs were converted to clkdev mappings were added for the
I2C controllers on them. On S3C6410 a device name is specified for I2C
controller 1 but not for controller 0 which makes the code less robust as
we'll falsely return the clock for controller 0 if there's an error in the
request for controller 1.
Improve things by registering a device name for controller 0 as well. Due
to the fact that we change the numbering for controller 0 depending on if
we've registered controller 1 this requires an ifdef to choose the name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that it's in common.c it's not used in multiple source files.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pdata needs to be freed before leaving the function in an error case.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently MMC2 setup code can only enable loopback clock and
relies on reset value for boards that need to have it disabled.
This causes a problem with certain bootloaders that always enable
that clock, resulting with unwanted bootloader dependencies.
Fix this by making it disable the clock if board data says so.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc23_before_set_reg() can set MMCSDIO2ADPCLKISEL bit, which
enables internal clock for MMC2. Currently this function is also called
by code handling MMC3, and if .internal_clock is set in platform data
(by default it currently is), it will set MMCSDIO2ADPCLKISEL for MMC2
instead of MMC3 (MMC3 doesn't have such bit so nothing actually needs to
be done). This breaks 2nd SD slot on pandora.
Fix this by changing hsmmc23_before_set_reg() to only handle MMC2.
Note that this removes .remux() call for MMC3, but no board currently
needs it and it's also not called for MMC4 and MMC5.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
following statement can only change device size from 8-bit(0) to 16-bit(1),
but not vice versa:
regval |= GPMC_CONFIG1_DEVICESIZE(wval);
so as this field has 1 reserved bit, that could be used in future,
just clear both bits and then OR with the desired value
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 2f0778af (ARM: 7205/2: sched_clock: allow sched_clock to be
selected at runtime) had a typo for the case when CONFIG_OMAP_32K_TIMER
is not set.
In dmtimer_read_sched_clock(), wrong argument was getting passed to
__omap_dm_timer_read_counter() function call; instead of "&clksrc",
we were passing "clksrc.io_base", which results into kernel crash.
To reproduce kernel crash, just disable the CONFIG_OMAP_32K_TIMER config
option (and DEBUG_LL) and build/boot the kernel.
This will use dmtimer as a kernel clocksource and lead to kernel
crash during boot -
[ 0.000000] OMAP clocksource: GPTIMER2 at 26000000 Hz
[ 0.000000] sched_clock: 32 bits at 26MHz, resolution 38ns, wraps every
165191ms
[ 0.000000] Unable to handle kernel paging request at virtual address
00030ef1
[ 0.000000] pgd = c0004000
[ 0.000000] [00030ef1] *pgd=00000000
[ 0.000000] Internal error: Oops: 5 [#1] SMP
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (3.3.0-rc1-11574-g0c76665-dirty #3)
[ 0.000000] PC is at dmtimer_read_sched_clock+0x18/0x4c
[ 0.000000] LR is at update_sched_clock+0x10/0x84
[ 0.000000] pc : [<c00243b8>] lr : [<c0018684>] psr: 200001d3
[ 0.000000] sp : c0641f38 ip : c0641e18 fp : 0000000a
[ 0.000000] r10: 151c3303 r9 : 00000026 r8 : 76276259
[ 0.000000] r7 : 00028547 r6 : c065ac80 r5 : 431bde82 r4 : c0655968
[ 0.000000] r3 : 00030ef1 r2 : fb032000 r1 : 00000028 r0 : 00000001
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode_amd: Add support for CPU family specific container files
x86/amd: Add missing feature flag for fam15h models 10h-1fh processors
x86/boot-image: Don't leak phdrs in arch/x86/boot/compressed/misc.c::Parse_elf()
x86/numachip: Drop unnecessary conflict with EDAC
x86/uv: Fix uninitialized spinlocks
x86/uv: Fix uv_gpa_to_soc_phys_ram() shift
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
rsyslog will display KERN_EMERG messages on a connected
terminal. However, these messages are useless/undecipherable
for a general user.
For example, after a softlockup we get:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Stack:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Call Trace:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Code: ff ff a8 08 75 25 31 d2 48 8d 86 38 e0 ff ff 48 89
d1 0f 01 c8 0f ae f0 48 8b 86 38 e0 ff ff a8 08 75 08 b1 01 4c 89 e0 0f 01 c9 <e8> ea 69 dd ff 4c 29 e8 48 89 c7 e8 0f bc da ff 49 89 c4 49 89
This happens because the printk levels for these messages are
incorrect. Only an informational message should be displayed on
a terminal.
I modified the printk levels for various messages in the kernel
and tested the output by using the drivers/misc/lkdtm.c kernel
modules (ie, softlockups, panics, hard lockups, etc.) and
confirmed that the console output was still the same and that
the output to the terminals was correct.
For example, in the case of a softlockup we now see the much
more informative:
Message from syslogd@intel-s3e37-04 at Jan 25 10:18:06 ...
BUG: soft lockup - CPU4 stuck for 60s!
instead of the above confusing messages.
AFAICT, the messages no longer have to be KERN_EMERG. In the
most important case of a panic we set console_verbose(). As for
the other less severe cases the correct data is output to the
console and /var/log/messages.
Successfully tested by me using the drivers/misc/lkdtm.c module.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: dzickus@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1327586134-11926-1-git-send-email-prarit@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Quite oddly, all of the arguments passed through from the top
level macros to the second level which didn't need parentheses
had them, while the only expression (involving a parameter)
needing them didn't.
Very recently I got bitten by the lack thereof when using
something like "array + index" for the first operand, with
"array" being an array more narrow than int.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/4F2183A9020000780006F3E6@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following build error found when building imx_v4_v5_defconfig:
CC arch/arm/mach-imx/mach-imx27ipcam.o
In file included from arch/arm/plat-mxc/include/mach/iomux-mx27.h:23,
from arch/arm/mach-imx/mach-imx27ipcam.c:22:
arch/arm/plat-mxc/include/mach/iomux-v1.h:99: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'imx_iomuxv1_init'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure
this GPIO in the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.
This patch renames the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
We've decided to provide CPU family specific container files
(starting with CPU family 15h). E.g. for family 15h we have to
load microcode_amd_fam15h.bin instead of microcode_amd.bin
Rationale is that starting with family 15h patch size is larger
than 2KB which was hard coded as maximum patch size in various
microcode loaders (not just Linux).
Container files which include patches larger than 2KB cause
different kinds of trouble with such old patch loaders. Thus we
have to ensure that the default container file provides only
patches with size less than 2KB.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120120164412.GD24508@alberich.amd.com
[ documented the naming convention and tidied the code a bit. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
That is the last one missing for those CPUs.
Others were recently added with commits
fb215366b3
(KVM: expose latest Intel cpu new features (BMI1/BMI2/FMA/AVX2) to guest)
and
commit 969df4b829
(x86: Report cpb and eff_freq_ro flags correctly)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/r/20120120163823.GC24508@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Initialize two spinlocks in tlb_uv.c and also properly define/initialize
the uv_irq_lock.
The lack of explicit initialization seems to be functionally
harmless, but it is diagnosed when these are turned on:
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_LOCKDEP=y
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/E1RnXd1-0003wU-PM@eag09.americas.sgi.com
[ Added the uv_irq_lock initialization fix by Dimitri Sivanich ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
uv_gpa_to_soc_phys_ram() was inadvertently ignoring the
shift values. This fix takes the shift into account.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120119020753.GA7228@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dss_core has to be initialized before any other DSS hwmod. Currently
this is broken as dss_core is listed in chip/revision specific hwmod
lists while other DSS hwmods are listed in common list which is
registered first.
This patch moves DSS hwmods (except for dss_core) to the separate list
which is registered last to ensure that dss_core is already registered.
This solves the problem with BUG() in L3 interrupt handler on boards
with DSS enabled in bootloader.
The long-term fix to this is to ensure modules are set up in dependency
order in the hwmod core code.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Archit Taneja <archit@ti.com>
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
[paul@pwsan.com: add notes that this is just a temporary workaround until
hwmod dependencies are added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 22f51371f8 ("ARM: OMAP3: pm: use
prcm chain handler") breaks the build on a 2420-only config, due to
a missing include for plat/irqs.h:
CC arch/arm/mach-omap2/prm2xxx_3xxx.o
arch/arm/mach-omap2/prm2xxx_3xxx.c:41:11: error: 'INT_34XX_PRCM_MPU_IRQ' undeclared here (not in a function)
Fix by explicitly including it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Commit 7b250aff1c ("ARM: OMAP: Avoid
cpu_is_omapxxxx usage until map_io is done") breaks the build on a
2420-only config on v3.3-rc1:
arch/arm/mach-omap2/built-in.o: In function `omap2430_init_early':
arch/arm/mach-omap2/io.c:406: undefined reference to `omap2_set_globals_243x'
arch/arm/mach-omap2/io.c:410: undefined reference to `omap243x_clockdomains_init'
arch/arm/mach-omap2/io.c:411: undefined reference to `omap2430_hwmod_init'
Fix by only compiling omap2420_init_early() when CONFIG_SOC_OMAP2420
is selected, and only compiling omap2430_init_early() when
CONFIG_SOC_OMAP2430 is selected.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
To be able to get the memory resources by name from
the DMIC driver (for MPU and for DMA).
Without this patch, functionality that was working in 3.2 breaks in
3.3-rc1. This patch should have gone in as part of the 3.3 merge
window, but was inadvertently missed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: added commit message note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
dispc's sysc_flags is missing SYSC_HAS_ENAWAKEUP flag. This seems to
cause SYNC_LOST errors from the DSS when the power management is
enabled.
This patch adds the missing SYSC_HAS_ENAWAKEUP flag. Note that there are
other flags missing also (clock activity, DSI's sysc flags), but as they
are not critical, they will be fixed in the next merge window.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently OMAP2 and 3 share the same omap_hwmod_class and
omap_hwmod_class_sysconfig for dispc. However, OMAP3 has sysconfig
bits that OMAP2 doesn't have, so we need to split those structs into
OMAP2 and OMAP3 specific versions.
This patch only splits the structs, without changing the contents.
This is a prerequisite for a subsequent fix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: added commit note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This macro is used to generate unprivileged accesses (LDRT/STRT) to user
space.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dynamic ftrace ops startup test currently fails on Thumb-2 kernels:
Testing tracer function: PASSED
Testing dynamic ftrace: PASSED
Testing dynamic ftrace ops #1: (0 0 0 0 0) FAILED!
This is because while the addresses in the mcount records do not have
the zero bit set, the IP reported by the mcount call does have it set
(because it is copied from the LR). This mismatch causes the ops
filtering in ftrace_ops_list_func() to not call the relevant tracers.
Fix this by clearing the zero bit before adjusting the LR for the mcount
instruction size. Also, combine the mov+sub into a single sub
instruction.
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 0536bdf33f (ARM: move iotable mappings within
the vmalloc region), the RealView PB11MP cannot boot anymore.
This is caused by the way the mappings are described on this
platform (define replaced by hex values for clarity):
{ /* GIC CPU interface mapping */
.virtual = IO_ADDRESS(0x1F000100),
.pfn = __phys_to_pfn(0x1F000100),
.length = SZ_4K,
.type = MT_DEVICE,
}, { /* GIC distributor mapping */
.virtual = IO_ADDRESS(0x1F001000),
.pfn = __phys_to_pfn(0x1F001000),
.length = SZ_4K,
.type = MT_DEVICE,
}
The first mapping ends up reserving two pages, and clashes with
the second one, which triggers a BUG_ON in vm_area_add_early().
In order to solve this problem, treat the MPCore private memory
region (containing the SCU, the GIC and the TWD) as a single region,
as described in the TRM:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0360f/CACGDJJC.html
The EB11MP is converted the same way, even if it manages to avoid
the problem.
Tested on both PB11MP and EB11MP.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix build on some non-freescale platforms
powerpc/powernv: Fix PCI resource handling
powerpc/crash: Fix build error without SMP
powerpc/cpuidle: Make it a bool, not a tristate
powerpc/85xx: Add dr_mode property in USB nodes
powerpc/85xx: Enable USB2 controller node for P1020RDB
powerpc/85xx: Fix cmd12 bug and add the chip compatible for eSDHC
arch/powerpc/sysdev/fsl_pci.c: add missing iounmap
powerpc: fix compile error with 85xx/p1022_ds.c
Commit 9deaa53ac7 broke build
on platforms that use legacy_serial.c without also having
CONFIG_SERIAL_8250_FSL enabled due to an unconditional code
to a routine in that module.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent changes to the handling of PCI resources for host bridges
are breaking the PowerNV code for assigning resources on IODA.
The root of the problem is that the pci_bus attached to a host
bridge no longer has its "legacy" resource pointers populated
but only uses the newer list instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Davem says:
1) Fix JIT code generation on x86-64 for divide by zero, from Eric Dumazet.
2) tg3 header length computation correction from Eric Dumazet.
3) More build and reference counting fixes for socket memory cgroup
code from Glauber Costa.
4) module.h snuck back into a core header after all the hard work we
did to remove that, from Paul Gortmaker and Jesper Dangaard Brouer.
5) Fix PHY naming regression and add some new PCI IDs in stmmac, from
Alessandro Rubini.
6) Netlink message generation fix in new team driver, should only advertise
the entries that changed during events, from Jiri Pirko.
7) SRIOV VF registration and unregistration fixes, and also add a
missing PCI ID, from Roopa Prabhu.
8) Fix infinite loop in tx queue flush code of brcmsmac, from Stanislaw Gruszka.
9) ftgmac100/ftmac100 build fix, missing interrupt.h include.
10) Memory leak fix in net/hyperv do_set_mutlicast() handling, from Wei Yongjun.
11) Off by one fix in netem packet scheduler, from Vijay Subramanian.
12) TCP loss detection fix from Yuchung Cheng.
13) TCP reset packet MD5 calculation uses wrong address, fix from Shawn Lu.
14) skge carrier assertion and DMA mapping fixes from Stephen Hemminger.
15) Congestion recovery undo performed at the wrong spot in BIC and CUBIC
congestion control modules, fix from Neal Cardwell.
16) Ethtool ETHTOOL_GSSET_INFO is unnecessarily restrictive, from Michał Mirosław.
17) Fix triggerable race in ipv6 sysctl handling, from Francesco Ruggeri.
18) Statistics bug fixes in mlx4 from Eugenia Emantayev.
19) rds locking bug fix during info dumps, from your's truly.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
rds: Make rds_sock_lock BH rather than IRQ safe.
netprio_cgroup.h: dont include module.h from other includes
net: flow_dissector.c missing include linux/export.h
team: send only changed options/ports via netlink
net/hyperv: fix possible memory leak in do_set_multicast()
drivers/net: dsa/mv88e6xxx.c files need linux/module.h
stmmac: added PCI identifiers
llc: Fix race condition in llc_ui_recvmsg
stmmac: fix phy naming inconsistency
dsa: Add reporting of silicon revision for Marvell 88E6123/88E6161/88E6165 switches.
tg3: fix ipv6 header length computation
skge: add byte queue limit support
mv643xx_eth: Add Rx Discard and Rx Overrun statistics
bnx2x: fix compilation error with SOE in fw_dump
bnx2x: handle CHIP_REVISION during init_one
bnx2x: allow user to change ring size in ISCSI SD mode
bnx2x: fix Big-Endianess in ethtool -t
bnx2x: fixed ethtool statistics for MF modes
bnx2x: credit-leakage fixup on vlan_mac_del_all
macvlan: fix a possible use after free
...
I could not find cpus_in_crash anywhere in the sourcetree, except for
arch/powerpc/kernel/crash.c. Moving the definition into the CONFIG_SMP
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As pointed out, asm/system.h has empty inline implementations for
update_smt_snooze_delay and pseries_notify_cpuidle_add_cpu, which are
used when CONFIG_PSERIES_IDLE is undefined. Since those two functions
are used in core power architecture functions (store_smt_snooze_delay
at kernel/sysfs.c and smp_xics_setup_cpu at platforms/pseries/smp.c),
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If NR_CPUS < 256 then arch_spinlock_t is only 16 bits wide but struct
xen_spinlock is 32 bits. When a spin lock is contended and
xl->spinners is modified the two bytes immediately after the spin lock
would be corrupted.
This is a regression caused by 84eb950db1
(x86, ticketlock: Clean up types and accessors) which reduced the size
of arch_spinlock_t.
Fix this by making xl->spinners a u8 if NR_CPUS < 256. A
BUILD_BUG_ON() is also added to check the sizes of the two structures
are compatible.
In many cases this was not noticable as there would often be padding
bytes after the lock (e.g., if any of CONFIG_GENERIC_LOCKBREAK,
CONFIG_DEBUG_SPINLOCK, or CONFIG_DEBUG_LOCK_ALLOC were enabled).
The bnx2 driver is affected. In struct bnx2, phy_lock and
indirect_lock may have no padding after them. Contention on phy_lock
would corrupt indirect_lock making it appear locked and the driver
would deadlock.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
CC: stable@kernel.org #only 3.2
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There's no need to keep the DMA_REQ_SEL defines inside the ifdef.
Fixes the following build break with CONFIG_TEGRA_SYSTEM_DMA=n:
arch/arm/mach-tegra/devices.c:645: error: 'TEGRA_DMA_REQ_SEL_I2S_1' undeclared here (not in a function)
arch/arm/mach-tegra/devices.c:663: error: 'TEGRA_DMA_REQ_SEL_I2S2_1' undeclared here (not in a function)
arch/arm/mach-tegra/devices.c:663: error: initializer element is not constant
arch/arm/mach-tegra/devices.c:663: error: (near initialization for 'i2s_resource2[1].start')
arch/arm/mach-tegra/devices.c:664: error: initializer element is not constant
arch/arm/mach-tegra/devices.c:664: error: (near initialization for 'i2s_resource2[1].end')
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This table is required to support the gpio_to_irq() translation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add videodev2 header which provides V4L2_PIX_FMT_RGB565 to fix:
arch/arm/mach-shmobile/board-ag5evm.c:274: error: 'V4L2_PIX_FMT_RGB565' undeclared here (not in a function)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZgSs
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-imx-move' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Consolidate i.MX 5 platforms to be under the new shared i.MX 3/5/6 tree.
* tag 'arm-soc-imx-move' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM i.MX: Update defconfig
ARM i.MX: Merge i.MX5 support into mach-imx
ARM i.MX5: remove unnecessary includes from board files
Fix up fairly trivial conflicts due to various changes nearby in
arch/arm/{mach,plat}-imx/{Kconfig,Makefile}
Pull request had been sent to the wrong email address, but happened
before the merge window closed. I'm merging the MX 5 consolidation,
since it apparently will help the next development window and will avoid
conflicts later as per Arnd.
If the provided system call number is equal to __NR_syscalls, the
current check will pass and a function pointer just after the system
call table may be called, since sys_call_table is an array with total
size __NR_syscalls.
Whether or not this is a security bug depends on what the compiler puts
immediately after the system call table. It's likely that this won't do
anything bad because there is an additional NULL check on the syscall
entry, but if there happens to be a non-NULL value immediately after the
system call table, this may result in local privilege escalation.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: <stable@vger.kernel.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kdump only allocates memory for the prstatus ELF note. For s390x,
besides of prstatus multiple ELF notes for various different register
types are stored. Therefore the currently allocated memory is not
sufficient. With this patch the KEXEC_NOTE_BYTES macro can be defined
by architecture code and for s390x it is set to the correct size now.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Jornada SSP driver is supposed to be initialized by a
module_init() call, but it was missed at some merge point. Since
the driver mostly pass calls through it magically works anyway,
but needs to be rectified.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On secondary CPUs, the Timer Control Register is not reset
to a sane value before the timer is registered, and the TRM
doesn't seem to indicate any reset value either. In some cases,
the kernel will take an interrupt too early, depending on what
junk was present in the registers at reset time.
The fix is to set the Timer Control Register to 0 before
registering the clock_event_device and enabling the interrupt.
Problem seen on VE (Cortex A5) and Tegra.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On v7, we use the same cache maintenance instructions for data lines
as for unified lines. This was not the case for v6, where HARVARD_CACHE
was defined to indicate the L1 cache topology.
This patch removes the erroneous compile-time check for HARVARD_CACHE in
proc-v7.S, ensuring that we perform I-side invalidation at boot.
Reported-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Catalin Marinas <Catalin.Marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The merging of commits 1b6ba46b ("ARM: LPAE: MMU setup for the 3-level
page table format") and b4244738 ("ARM: 7202/1: Add Cortex-A7 proc info")
during the merge window ended up putting the Cortex-A7 proc_info into a
code block guarded by !CONFIG_ARM_LPAE. This makes Cortex-A7 platforms
unbootable when LPAE is enabled.
This patch moves the proc_info structure for Cortex-A7 outside of the
guarded block.
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It turns out that the logical CPU mapping is useful even when !CONFIG_SMP
for manipulation of devices like interrupt and power controllers when
running a UP kernel on a CPU other than 0. This can happen when kexecing
a UP image from an SMP kernel.
In the future, multi-cluster systems running AMP configurations will
require something similar for mapping cluster IDs, so it makes sense to
decouple this logic in preparation for this support.
Acked-by: Yang Bai <hamo.by@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To ensure correct alignment of cacheline-aligned data, the maximum
cacheline size needs to be known at compile time.
Since Cortex-A8 and Cortex-A15 have 64-byte cachelines (and it is likely
that there will be future ARMv7 implementations with the same line size)
then it makes sense to assume that CPU_V7 implies a 64-byte L1 cacheline
size. For CPUs with smaller caches, this will result in some harmless
padding but will help with single zImage work and avoid hitting subtle
bugs with misaligned data structures.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The exception fixup table is currently aligned to a 32-byte boundary.
Whilst this won't cause any problems, the exception_table_entry
structures contain only a pair of unsigned longs, so 4-byte alignment
is all that is required. If the table was walked from start to end,
cacheline alignment may bring some performance benefits, but since a
binary search is used, the access pattern is random and will not benefit
from a stricter alignment.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The linker script assumes a cacheline size of 32 bytes when aligning
the .data..cacheline_aligned and .data..percpu sections.
This patch updates the script to use L1_CACHE_BYTES, which should be set
to 64 on platforms that require it.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Passing the address of a variable as an operand to an asm statement
doesn't mark the value of this variable as used, so gcc may optimize its
initialisation away. Fix this by using the "m" constraint instead.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Paul Walmsley