Pin configurations can be per-pin or per-group. Make sure that the
per-group case is covered by the bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For function and group configuration nodes, use "function"
"groups" string pairs, not "pins" where there should be
"groups".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add "power-source" property to generic options used for DT parsing files.
This enables drivers, which use generic pin configurations, to get the
value passed to this property.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl bindings can benefit from generic property names that define
which pins a "pin configuration node" affects, and which mux function
to select onto those pins. Document new properties for this purpose so
that other bindings may refer to them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reword the section of pinctrl-bindings.txt that describes generic
properties that pinctrl bindings may use. The aim is to make the text
clearer, and more explicitly call out the responsibility of individual
bindings that use the generic properties to define which of the
properties are used, and how.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some options currently take arguments in unspecified driver-specific units.
As pointed out by Stephen Warren, driver specific values should not be part
of generic devicetree bindings describing the hardware.
Therefore remove the critical bindings again, before they become part of
an official release.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the debounce time pinconfig option uses an unspecified
"time units" unit. As pinconfig options should use SI units and a
real unit is also necessary for generic dt bindings, change it
to usec. Currently no driver is using the generic pinconfig option
for this, so the unit change is safe to do.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PULL_PIN_DEFAULT is meant for hardware completely hiding any pull
settings from the driver, so that it's really only possible to turn
the pull on or off, but it not being possible to determine any
pull settings from software.
Also the binding-documentation for the pull arguments did not match
the changes to the expected values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bias-pull-* options use values > 0 to indicate that the pull should
be activated and optionally also indicate the strength of the pull.
Therefore use an default value of 1 for these options.
Split the low-power-mode option into low-power-enable and -disable.
Update the documentation to describe the param arguments better.
Reported-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinconf_generic_parse_dt_config() takes a node as input and generates an
array of generic pinconfig values from the properties of this node.
As I couldn't find a mechanism to count the number of properties of a node
the function uses internally an array to accept one of parameter and copies
the real present options to a smaller variable at its end.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core pin controller bindings define:
* The fact that pin controllers expose pin configurations as nodes in
device tree.
* That the bindings for those pin configuration nodes is defined by the
individual pin controller drivers.
* A standardized set of properties for client devices to define numbered
or named pin configuration states, each referring to some number of the
afore-mentioned pin configuration nodes.
* That the bindings for the client devices determines the set of numbered
or named states that must exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Baruch Siach