Tuning a card with Sony ASCOT2E produces the following error:
kernel: i2c i2c-9: wr reg=0006: len=11 is too big!
MAX_WRITE_REGSIZE is defined as 10, buf[MAX_WRITE_REGSIZE + 1] buffer is
used in ascot2e_write_regs().
The problem is that exactly 10 bytes are written in ascot2e_set_params():
/* Set BW_OFFSET (0x0F) value from parameter table */
data[9] = ascot2e_sett[tv_system].bw_offset;
ascot2e_write_regs(priv, 0x06, data, 10);
The test in write_regs is as follows:
if (len + 1 >= sizeof(buf))
10 + 1 = 11 and that would be exactly the size of buf. Since 10 bytes +
buf[0] = reg would seem to fit into buf[], this shouldn't be an error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix two warnings:
af9033.c: In function 'af9033_read_status':
af9033.c:883:25: warning: 'snr_lut' may be used uninitialized in this function [-Wmaybe-uninitialized]
const struct val_snr *snr_lut;
^
af9033.c:952:25: warning: 'tmp' may be used uninitialized in this function [-Wmaybe-uninitialized]
c->cnr.stat[0].svalue = tmp;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current code will expose a zero value if one of the stats is
not available, but this is not what userspace expects. Instead,
if something goes wrong on providing some stats, it should be
changing the scale to FE_SCALE_NOT_AVAILABLE.
So, change the logic to do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cxd2841er_read_agc_gain_c added to obtain signal strength.
signal strength now relay on AGC value.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The signal strength value is reversed: the bigger the number,
the weaker is the signal.
Fix the logic and present it in dBm. Please notice that the
dBm measure is actually an estimation, as the ratio is not
fully linear. It also varies with the frequency.
Yet, the estimation should be good enough for programs like
Kaffeine to indicate when the signal is good or bad.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is a good idea to measure the signal strength while
tuning, as this helps to identify if the antenna is ok.
Also, such measure helps to identify the quality of the
signal.
Do some changes to enable it before signal lock. While
here, optimize the code to only initialize the stats
length once, and make sure that, just after set_frontend,
any reading for the stats that depends on lock to return
FE_SCALE_NOT_AVAILABLE.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move statistics polling to read_status() in order to avoid use of
kernel work. Also replace home made sign extension used for
statistics with kernel sign_extend32().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move statistics polling to read_status() in order to avoid use of
kernel work.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* remove some unneeded variable initialization
* rename variables
* use min() macro to calc max i2c xfer len
* change bad firmware error code from EFAULT to EINVAL
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There was some calculations where was kHz used in order to keep
calculation withing 32-bit. Convert all to Hz and use 64-bit
division helpers where needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
DiSEqC message sending takes 13.5 ms per byte, which is 54 ms total
when typical 4 byte message is sent. Don't hard-code time limit to
54 ms, but calculate it. Time limit is only used to determine when to
start poll "DiSEqC Tx ready" status from the chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No need to clear negative msb bits as those were dropped in any
case when data is written to register.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Si2168-B40 firmware API has changed somewhere between 4.0-11 and
4.0-19 so that sleep will lose firmware upgrade from the chip. Due
to that firmware re-upload is needed when newer firmwares are used.
Rewrote firmware handling logic partly at the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those tables are currently unused, so comment them out:
drivers/media/dvb-frontends/dib0090.c:852:18: warning: 'rf_ramp_pwm_sband' defined but not used [-Wunused-const-variable=]
static const u16 rf_ramp_pwm_sband[] = {
^~~~~~~~~~~~~~~~~
drivers/media/dvb-frontends/dib0090.c:800:18: warning: 'bb_ramp_pwm_boost' defined but not used [-Wunused-const-variable=]
static const u16 bb_ramp_pwm_boost[] = {
^~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid this warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1243:18: warning: 'nicam_presc_table_val' defined but not used [-Wunused-const-variable=]
static const u16 nicam_presc_table_val[43] = {
^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
status is not initialized so it can contain garbage. The
check for status containing the FE_HAS_LOCK bit may randomly pass
or fail if the read of register 0x8c fails to set status after 25
read attempts. Fix this by initializing status to 0.
Issue found with CoverityScan, CID#986738
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The rtl2832 demod has 2 sets of PID filters. This patch enables
the filter support when using a slave demod.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return -EINVAL if ds3000_set_frontend is called with invalid parameters.
v1 of the patch series got incorrect subject lines.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move mn88472 DVB-T/T2/C demod driver out of staging to media.
v2: Fix build error reported by kbuild test robot:
drivers/staging/media/mn88472/Makefile: No such file or directory
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Finalize driver in order to move out of staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Latest, 3rd, regmap instance should be freed on error case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/helene.c: In function 'helene_write_regs':
drivers/media/dvb-frontends/helene.c:312:5: warning: format '%lu' expects argument of type 'long unsigned int', but argument 5 has type 'unsigned int' [-Wformat=]
"wr reg=%04x: len=%d vs %lu is too big!\n",
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
correct is CXD2841ER and CXD2854ER
incorrect was CXD2441ER and CXD2454ER
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
now when new tuning parameters specified demod should retune.
Also ISDB-T frequency offset calculation added
(cxd2841er_get_carrier_offset_i).
While here, fix re-tune for DVB-C Annex A, using the desired
bandwidth, instead of using 8MHz.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Avoid error message:
cxd2841er_read_status_s(): invalid state 1
Always force demod to shutdown state before initializing
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
CXD2854ER is identical to CXD2841ER except ISDB-T/S added.
New method 'cxd2841er_attach_i' is added
xtal frequency now configurable. Available options:
20.5MHz, 24MHz, 41MHz
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is Sony HELENE DVB-S/S2 DVB-T/T2 DVB-C/C2 ISDB-T/S tuner
driver (CXD2858ER).
Tuner is used on NetUP Dual Universal DVB CI card (hardware revision 1.4).
Use 'helene_attach_s' to attach tuner in 'satellite mode'.
Use 'helene_attach' for 'terrestrial mode'.
Satellite delivery systems supported:
DVB-S/S2, ISDB-S
Terrestrial delivery systems supported:
DVB-T/T2, ISDB-T
Cable delivery systems supported:
DVB-C/C2
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
The ds3000 driver returned 1 as an error code in many places.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using div_u64() instead of do_div() makes the code slightly more
readable by humans.
[mchehab@osg.samsung.org: originally, this patch was proposed as a bug
fix for a gcc bug. This was solved already, but it is still better to
use div_u64, instead of do_div, so I'm applying it, removing the
comments about the gcc bug]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the regmap overrides
that makes the i2c accesses unlocked and use plain old regmap
accesses. This also removes the need for the regmap wrappers used by
rtl2832_sdr, so deconvolute the code further and provide the regmap
handle directly instead of the wrapper functions.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the code that makes the
i2c accesses unlocked. But add a mutex so that firmware commands are
still serialized.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Saso Slavicic