Tulip throws an error when dma debugging is enabled, as it doesn't properly
check dma mapping results with dma_mapping_error() durring tx ring refills.
Easy fix, just add it in, and drop the frame if the mapping is bad
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that the driver increments the "RX length error"
on every buffer in sh_eth_rx() if the R8A7740.
This patch also adds a description about the Receive Frame Status bits.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the SoC specific support is no longer done with help of #ifdef'fery,
we no longer need '__maybe_unused' annotations to sh_eth_select_mii() and
sh_eth_set_duplex()...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems that don't need wake-on-lan may choose to power down the
chip on system standby. Upon resume, the power on causes the boot code
to startup and initialize the hardware. On one new platform, this is
causing the device to go into a bad state due to a race between the
driver and boot code, once every several hundred resumes. The same race
exists on open since we come up from a power on.
This patch adds a wait for boot code signature at the beginning of
tg3_init_hw() which is common to both cases. If there has not been a
power-off or the boot code has already completed, the signature will be
present and poll_fw() returns immediately. Also return immediately if
the device does not have firmware.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c: In function:
stmmac_xmit drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1902:74:
error: expected ) before __func__
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to set the coherent DMA mask only if dma_set_mask() succeeded, and to
error out if either fails.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device::dev_id should not be used merely to indicate a VI index,
as it affects the way the local part of IPv6 addresses is normally
generated.
This field was intended for use where multiple devices may share a
single assigned MAC address and need to have different IPv6 addresses.
T4 VIs each have their own MAC address.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9f86134155 (sh_eth: remove SH_ETH_HAS_TSU)
removes 'const' from 'sh_eth_netdev_ops' and modifies it in case TSU registers
are present. I've originally suggested to Iwamatsu-san to split this structure
in two instead and afterwards Dave M. suggested doing the same.
Split 'sh_eth_netdev_ops_tsu' from 'sh_eth_netdev_ops', making both 'const', and
assigning 'ndev->detdev_ops' depending on the presence of TSU registers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ibmebus is the last remaining user of of_platform_driver and the
conversion to a regular platform driver is trivial.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Older Single Queue (SQ_SG_MODE) devices like TSEC (i.e. mpc83xx)
don't feature the frame receive indication bits (RXF) in RSTAT.
For these and for the rest of the SQ_SG_MODE devices, provide the
appropiate polling routine that handles a single pair of Rx/Tx
BD rings, removing the overhead incurred by the multiple queues/
multiple interrupt group devices (veTSEC/ eTSEC2.0 devices).
So this is primarily a fix for the TSEC devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not use net_device::dev_id to indicate the port number, as
this affects the way the local part of IPv6 addresses is normally
generated.
This field was intended for use where multiple devices may share a
single assigned MAC address and need to have different IPv6 addresses.
Siena's two ports each have their own MAC addresses.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 75096579c3 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: netdev@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
CC: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 75096579c3 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: netdev@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI driver's probe() method duplicates the error cleanup code each time it
has to do error exit. Consolidate the error cleanup code in one place and use
*goto* to jump to the right places.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first loop in sh_eth_check_reset() runs to its end, 'cnt' is 0, so the
following check for 'cnt < 0' fails to catch the timeout. Fix the condition in
this check, so that the timeout is actually reported.
While at it, fix the grammar in the failure message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
was playing with suspend and run into this:
|BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891
|in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash
|6 locks held by bash/1963:
|CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50
|[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14)
|[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac)
|[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c)
|[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54)
|[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64)
|[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c)
|[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230)
|[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350)
|[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c)
|[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc)
|[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20)
|[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c)
|[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190)
|[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70)
|[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48)
I don't see a reason why the pm_runtime call must be under the lock.
Further I don't understand why this is a spinlock and not mutex.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional statistics to the ixgbe driver for ndo_ll_poll
Defined under LL_EXTENDED_STATS
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ixgbe driver code implementing ndo_ll_poll.
Adds ndo_ll_poll method and locking between it and the napi poll.
When receiving a packet we use skb_mark_ll to record the napi it came from.
Add each napi to the napi_hash right after netif_napi_add().
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer Broadcom BCM63xx SoCs: 6328, 6362 and 6368 have an integrated switch
which needs to be driven slightly differently from the traditional
external switches. This patch introduces changes in arch/mips/bcm63xx in order
to:
- register a bcm63xx_enetsw driver instead of bcm63xx_enet driver
- update DMA channels configuration & state RAM base addresses
- add a new platform data configuration knob to define the number of
ports per switch/device and force link on some ports
- define the required switch registers
On the driver side, the following changes are required:
- the switch ports need to be polled to ensure the link is up and
running and RX/TX can properly work
- basic switch configuration needs to be performed for the switch to
forward packets to the CPU
- update the MIB counters since the integrated
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current bcm63xx_enet driver always uses bcmenet_shared_base whenever
it needs to access DMA channel configuration space or access the DMA
channel state RAM. Split these register in 3 parts to be more accurate:
- global DMA configuration
- per DMA channel configuration space
- per DMA channel state RAM space
This is preliminary to support new chips where the global DMA
configuration remains the same, but there is a varying number of DMA
channels located at a different memory offset.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the rset_nway ethtool callback which uses libphy generic
autonegotiation restart function.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't cast a plain integer to a pointer.
drivers/net/ethernet/renesas/sh_eth.c: In function ‘sh_eth_chip_reset_giga’:
drivers/net/ethernet/renesas/sh_eth.c:482:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/net/ethernet/renesas/sh_eth.c:483:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/net/ethernet/renesas/sh_eth.c:492:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/net/ethernet/renesas/sh_eth.c:493:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dependence on the certain SoCs is no longer necessary to compile the
driver, remove the dependency list from its Kconfig entry which is a popular
demand anyway...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the R-Car code/data in the driver out of #ifdef by adding "r8a777x-ether" to
the platfrom driver's ID table; since it's the last #ifdef, we remove CARDNAME
from the ID table and no longer check the driver data before assigning it to
'mdp->cd'...
Change the Ether platform device's name in the ARM platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the SH7724 code/data in the driver out of #ifdef by adding "r8a7724-ether"
to the platform driver's ID table. Change the Ether platform device's name in
the SH platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the SH7757 code/data in the driver out of #ifdef by adding "sh7757-ether"
and "sh7757-gether" to the platform driver's ID table. Note that we can remove
SH_ETH_HAS_BOTH_MODULES and sh_eth_get_cpu_data().
Change the Ether/GEther platform devices' names in the SH platform code
accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the SH77{34|63} specific code/data in the driver out of #ifdef by adding
"sh7734-gether" and "sh7763-gether" to the platform driver's ID table. Note
that we have to split the 'struct sh_eth_cpu_data' instance into two due to
#ifdef inside it; note that we can kill the duplicate sh_eth_set_rate_gether().
Change the GEther platform device's name in the SH platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the R8A7740 code/data in the driver out of #ifdef by adding "r8a7740-gether"
to the platform driver's ID table. Change the GEther platform device's name in
the ARM platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the SH7619 data in the driver out of #ifdef by adding "sh7619-ether" to the
platform driver's ID table. Change the Ether platform device's name in the SH
platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the SH771[02] data in the driver out of #ifdef by adding "sh771x-ether" to
the platform driver's ID table. Change the Ether platform device's name in the
SH platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to get away from the current driver's scheme of identifying a SoC
based on #ifdef's and the platform device ID table matching seems to be a good
replacement -- we can use the 'driver_data' field of 'struct platform_device_id'
as a pointer to a 'struct sh_eth_cpu_data'. Start by creating the initial table
with driver's name as the only entry without the driver data. Check the driver
data in the probe() method and if it's not NULL override 'mdp->cd' from it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing pdev in fec_ptp_init() is enough, since we can get ndev locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM is able to adapt its DMA buffer size, so change
the RX path to take advantage of this possibility and
remove all kind of memcpy in this path.
This modification introduces function pointers for managing
differences between MACB and GEM adapter type.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macb Ethernet controller requires a RX buffer of 128 bytes. It is
highly sub-optimal for Gigabit-capable GEM that is able to use
a bigger DMA buffer. Change this constant and associated macros
with data stored in the private structure.
RX DMA buffer size has to be multiple of 64 bytes as indicated in
DMA Configuration Register specification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put '#ifdef CONFIG_PM' around sh_eth_runtime_nop() and 'sh_eth_dev_pm_ops'.
Add '#define SH_ETH_PM_OPS' to facilitate initialization of driver's 'pm' field
depending on whether CONFIG_PM is enabled.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: added the changelog, reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has sh_eth_reset() function for each SoC and this function is almost
always the same, except for the several a bit different variations for Gigabit
Ethernet. Consolidate every variation into a single function -- which allows
us to get rid of some more #ifdef'fery.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: moved the new sh_eth_reset() and sh_eth_is_gether() up to decrease the
patch size, fixed function call continuation lines' indentation, reworded the
changelog, reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can simply remove #ifdef'fery around sh_eth_select_mii(). We have to annotate
it with '__maybe_unused' then.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: added the changelog, reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver supports some SH and SH-Mobile SOCs. There are SOCs with two or more
Ethernet devices, for these we need to pass IRQF_SHARED to request_irq(). Add
the 'irq_flags' field to the 'struct sh_eth_cpu_data' instead of #ifdef'fery.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: properly aligned request_irq() call continuation line, reworded the
changelog, reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove SH_ETH_HAS_TSU #define's and #ifdef's. Set three 'struct net_device_ops'
methods that depend on the presence of TSU basing on the 'tsu' field of 'struct
sh_eth_cpu_data'.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: made two method assignments one-liners, added the changelog, reworded
the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all the duplicate definitions of sh_eth_set_duplex() under different
#ifdef's, leaving only one outside the #ifdef's. We have to annotate it with
'__maybe_unused' since it's called not from all SoC #ifdef blocks.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: annotated sh_eth_set_duplex() as '__maybe_unused', added the changelog,
reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use now always available EDSR_ENALL instead of the bare number to set EDSR.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: added the changelog, reworded the subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove #ifdef around 'enum EDSR_BIT' and 'enum GECMR_BIT', replacing it with the
comments on which SoCs these registers exist.
SH7757 also has EDSR, so add a comment about it to 'enum EDSR_BIT'.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
[Sergei: folded in the former patch #2, updated the changelog, reworded the
subject, changing the prefix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some symbols referenced only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read data directly from platform recource table
and do not use of_irq_to_resource().
Also use devm_request_and_ioremap() for probe
functions simplification.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added sun4i-emac driver causes a build error when
CONFIG_NET_POLL_CONTROLLER is set, because it attempts to
assign a pointer to netdev->poll_controller, which has
been replaced with ops->ndo_poll_controller in 2.6.31!
The correct assignment is present as well, so we just need
to remove the wrong one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Maxime Ripard <maxime.ripard@anandra.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_select_queue() uses __skb_tx_hash to select the transmit queue.
XPS settings are ignored by this. Instead, we can use __netdev_pick_tx
to select the transmit queue.
Compile test only.
Signed-off-by: govindarajulu.v <govindarajulu90@gmail.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 driver has a suboptimal memory allocation strategy for regular
MTU=1500 frames, as it uses two page fragments :
One of 512 bytes and one of 1024 bytes.
This makes GRO less effective, as each GSO packet contains 8 MSS instead
of 16 MSS.
Performance of a single TCP flow gains 25 % increase with the following
patch.
Before patch :
A:~# netperf -H 192.168.0.2 -Cc
MIGRATED TCP STREAM TEST ...
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 13798.47 3.06 4.20 0.436 0.598
After patch :
A:~# netperf -H 192.68.0.2 -Cc
MIGRATED TCP STREAM TEST ...
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 17273.80 3.44 4.19 0.391 0.477
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 091f0ea300 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.
Cc: stable@vger.kernel.org
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the logic used by the mvneta driver to find a MAC
address for a particular interface. Until now, it was only looking at
the Device Tree, and if no address was found, was falling back to
generating a random MAC address.
This patch adds the intermediate solution of reading the MAC address
from the hardware registers, in case it has been set by the
bootloader. So the order is now:
1) MAC address from the Device Tree
2) MAC address from the hardware registers
3) Random MAC address
This requires moving the MAC address initialization a little bit later
in the ->probe() code, because it now requires the hardware registers
to be remapped.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE
register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are
indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not
setting them correctly on others (like TI DP83630) makes the PHY fall back
to 10M HDX mode which should be avoided.
Tested for TI DP83630 PHY on Microblaze platform.
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just fixed a typo in emac_probe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
76723bca28 "net: mv643xx_eth: add DT parsing support" added a
dummy mv643xx_eth_shared_of_probe() fallback function with a
typo.
This adds the missing semicolon so we can build without CONFIG_OF
again, and changes both dummy functions to the more conventional
"static inline" syntax, which can avoid potential problems with
the empty macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.
Commit 057cf65 "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.
This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/allocal/allocate/
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding phy-mode support to cpsw driver and updating the cpsw binding
documentation.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF sense they didn't get MAC address, use random one. This will
address the case of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).
Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.
Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When turning on adaptive_rx under adaptive moderation, the CQ's moderation
count wasn't updated according to rx_frames which resulted in too many
interrupts and bandwidth drop.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci_enable_device() will set device pm state to D0, so
it's no need to do it again in tg3_init_one().
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCA support has been removed but this dependency escaped removal.
Also, there is a duplicate PPC_PSERIES dependency that appeared
when the ethernet drivers were separated into vendor/model
specific directories, so we remove that here as well.
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PCIe supports PM capabilities, bnx2x will always claim eeprom is accessible
as PCI_D0 is zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes a few changes that change the driver's flow without truly
changing anything in its functionality - use usleep_range for short sleeps
instead of msleep and initialize Tx consumer during initialization for better
information during errors.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch revises many bnx2x prints - mainly fixing print typos and
adding some new debug prints (mostly for parity issues).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces several small changes to the driver, none which actually
change any flow:
1. Removes prototypes of unexisting functions and unused defines.
2. Fixes alignment and spacing issues.
3. Changes numeric usage into constants.
4. Remove unnecessary parenthesis.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch correct various typos, fix comments conventions and
adds/removes a few comments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary blank lines and adds a few where such are needed
(between variable declarations and code)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x_select_queue() was using __skb_tx_hash() to select the
transmit queue, totally ignoring XPS settings, while XPS can help
performance quite significantly, so change the bnx2x_select_queue()
to use __dev_pick_tx() instead which will use XPS if configured.
Based on patches from Ying Cai and Havard Skinnemoen
Reported-by: govindarajulu.v <govindarajulu90@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Ying Cai <ycai@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcing uninitialized state allows us to upgrade and reinitialize the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
At this point driver supports above and greater than above version of firmware.
If it doesn't find the required firmware version than it forces the adapter to
be reinitialized as shown below.
1) If FW_ON_ADAPTER < FW_VERSION and we're the MASTER_PF force uninitialized
state and a FW upgrade if available.
- If FW_ON_ADAPTER < /lib/firmware/cxgb4/t*fw.bin we will update the
adapters FW.
- If FW_ON_ADAPTER >= /lib/firmware/cxgb4/t*fw.bin don't upgrade FW.
- If upgrade_fw() fails force reinitialization of the adapter anyways,
it might still work.
Either way forcing the uninitialized state allows cxgb4 reinitialize FW.
2) If FW_ON_ADAPTER >= FW_VERSION driver follows normal path.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional 4 bytes found in the skb is the CRC calculated by the
CPDMA hardware, check the CRC bit in CPDMA status field of
Descriptor and remove the CRC length from the skb. This extra
4 byte can be seen when capturing packets using tcpdump.
This has been tested in TI816x platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A10 has an ethernet controller that seem to be developped
internally by them.
The exact feature set of this controller is unknown, since there is no
public documentation for this IP, and this driver is mostly the one
published by Allwinner that has been heavily cleaned up.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_device() will set device power state to D0,
so it's no need to do it again in tulip_init_one().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_device() will set device power state to D0,
so it's no need to do it again in qlcnic_attach_func().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_device() will set device power state to D0,
so it's no need to do it again in jme_init_one().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds device tree parsing support for the shared driver of mv643xx_eth.
As the bindings are slightly different from current PPC bindings new binding
documentation is also added. Following PPC-style device setup, the shared
driver now also adds port platform_devices and sets up port platform_data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet controllers found on Kirkwood SoCs not only suffer from loosing
MAC address register contents on clock gating but also some important
registers are reset to values that would break ethernet. This patch
clears the CLK125_BYPASS_EN bit for DT enabled Kirkwood only by using
of_device_is_compatible() instead of #ifdefs. Non-DT Kirkwood is not
affected as it installs a clock gating workaround because of the MAC
address issue above. Other Orion SoCs do not suffer from register reset,
do not have the bit in question, or do not have the register at all.
Moreover, system controllers on PPC using this driver should also be
protected from clearing that bit.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This connects to a phy node passed to the port device instead of probing
the phy by phy_addr.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of managed devm_ioremap and remove corresponding iounmap.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a separated mdio bus driver with mvmdio, phy_detach on network device
removal will not stop the phy and finally lead to NULL pointer dereference
in mvmdio due to non-existent network device. Use phy_disconnect instead
to properly stop phy device from accessing network device prior removal of
the network device.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable emaclite for Xilinx ARM Zynq platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emaclite can be used on ARM zynq where in_be32/out_be32 IO
functions are not present. Use standard __raw_readl/__raw_writel
IO functions instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xemaclite_adjust_link is used locally.
It removes sparse warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:916:6: warning:
symbol 'xemaclite_adjust_link' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.
Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapters do not support co-existence of INTx Interrupt with
MSI-X or MSI among multiple functions. Prevent attaching
of a function during normal load, if adapter gets into mixed
mode of interrupts
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o log "Unknown" board name and "Unknown" serial number in case
of mismatched adapter type found. This will avoid weird characters
logs when an adapter is in bad state or corrupted.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to save power, let's disable the regulator in the suspend function and
enable it in resume.
Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe the clocks are enabled prior than the acquiring the interrupts.
In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of error during probe, disable the PHY regulator.
Do the same in fec_drv_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.
This is wrong because at this point the interrupts have not even been acquired.
Swap failed_init/failed_irq to fix the error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().
This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For padded packets, Lancer computes incorrect checksum. The workaround is
to trim such packets. This workaround is mainly for IPv4 packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Lancer, packets that are 32 bytes or less may cause a transmit stall.
The work-around is to pad such packets to a 36 byte length.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the be_cmd_get_fw_ver() query from be_get_drvinfo() and invoking
the same from be_setup() and/or post firmware download.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the PCI power management scheme of the bnx2x driver to be similar
to those of most network drivers - the driver will now changes the power state
into D3hot whenever the driver will be removed, instead of whenever an
interface is unloaded.
This change enables the driver to access its eeprom via ethtool callbacks
even when interfaces are unloaded (such access requires the function to be
in D0active).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the PCI shutdown callback to support un-orderly shutdown, i.e.,
shutdowns in which the remove callback will not be called.
Due to the lack of this functionality, when an un-orderly shutdown occurred,
it was possible for wake-on-lan to remain disabled.
This is now fixed as the callback introduces the correct place in which
`system_state' can be queried and wake-on-lan be configured accordingly.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0eb43b4bb0
"bnx2x, bnx2fc: Use per port max exchange resources" has changed the number
of available FCoE exchanges, even in scenarios when some of the functions has
no FCoE support; This needlessly degraded the available resources.
Remedy this by calculating the maximal number of functions that may actually
utilize said connection.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF should ack the firmware when receiving unknown messages through the VF's
mailbox. This prevents the VF mailbox from being stuck in case of a VF sending
a message unknown to the PF (e.g. VF with more advanced version).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the print of the PCI gen3 link speed (8GHz), as well as correcting
the same print for 57712 boards (the print erroneously showed a 2.5GHz speed).
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hypervisor/Supervisor should set the VF's MAC prior to its load;
Using a randomly generated MAC as a default is a bad practice.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function
qlge_probe() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o GET_LED_STATUS command will be used by driver to get
current beacon state from 82xx adapter.
o Refactored qlcnic_store_beacon() to split 8200 and 8300
specific calls.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide diagnostics routines enough time to unwind before
proceeding with reset recovery.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test and set diagnostics mode bit before starting
diagnostics tests. Stop diagnostics tests if adapter is resetting.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o work_struct should be initialized before cancel_delayed_work
call to destroy it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_config_npars module parameter is used to configure NPAR
operational modes where NPAR function is used for PCI passthrough.
Removing this paramter as PCI passthrough is not supported for
NPAR functions.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Updated IRQ name for 8200 and 8300 Series adapter as per
format used by other multiqueue drivers.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set HW mask for 8300 Series adapter, in INT-x mode, to
stop generating interrupt during driver unload.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for spoof check configuration per VF using
iproute2 tool.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock was needed when flags used to be a u32 and set/cleared
using bit operations. Now that we use the atomic set_bit, this lock
isn't needed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the rings reset function and increase readability by moving the
control block disable code into separate functions.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code calls tg3_set_bdinfo() separately on napi0, followed by
a loop that does napi1+. Simplify it by setting bdinfo in the loop for
all napi contexts.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike the boot signature that needs to be set before every reset, the
ape state only needs to be updated to tell the firmware that the driver
is now taking/releasing control of the hardware. Move the calls to
tg3_ape_driver_state_change() to better, more appropriate places.
Also, the firmware does not distinguish between SUSPEND and START states
anymore. Remove the SUSPEND case in the switch.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"It's been a while since my last pull request so quite a few fixes have
piled up."
Indeed.
1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo
Neira Ayuso.
2) Fix data corruption on some tg3 chips with TSO enabled, from Michael
Chan.
3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar
Bandi.
4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in
scatter-gather entries into the crypto layer, the crypto layer can't
handle that. From Eric Dumazet.
5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet.
6) Fix OOPS in netfilter log module when called from conntrack, from
Hans Schillstrom.
7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the
non-BH disabling variants. From Fabio Estevam.
8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet.
9) vxlan driver doesn't update 'used' field of fdb entries when it
should, from Sridhar Samudrala.
10) ipv6 should use kzalloc() to allocate inet6 socket cork options,
otherwise we can OOPS in ip6_cork_release(). From Eric Dumazet.
11) Fix races in bonding set mode, from Nikolay Aleksandrov.
12) Fix checksum generation regression added by "r8169: fix 8168evl
frame padding.", from Francois Romieu.
13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet.
14) Fix checksum handling when GSO is enabled in bnx2x driver with
certain chips, from Yuval Mintz.
15) Fix double free in batman-adv, from Martin Hundebøll.
16) Fix device startup synchronization with firmware in tg3 driver, from
Nithin Sujit.
17) perf networking dropmonitor doesn't work at all due to mixed up
trace parameter ordering, from Ben Hutchings.
18) Fix proportional rate reduction handling in tcp_ack(), from Nandita
Dukkipati.
19) IPSEC layer doesn't return an error when a valid state is detected,
causing an OOPS. Fix from Timo Teräs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
be2net: bug fix on returning an invalid nic descriptor
tcp: xps: fix reordering issues
net: Revert unused variable changes.
xfrm: properly handle invalid states as an error
virtio_net: enable napi for all possible queues during open
tcp: bug fix in proportional rate reduction.
net: ethernet: sun: drop unused variable
net: ethernet: korina: drop unused variable
net: ethernet: apple: drop unused variable
qmi_wwan: Added support for Cinterion's PLxx WWAN Interface
perf: net_dropmonitor: Remove progress indicator
perf: net_dropmonitor: Use bisection in symbol lookup
perf: net_dropmonitor: Do not assume ordering of dictionaries
perf: net_dropmonitor: Fix symbol-relative addresses
perf: net_dropmonitor: Fix trace parameter order
net: fec: use a more proper compatible string for MVF type device
qlcnic: Fix updating netdev->features
qlcnic: remove netdev->trans_start updates within the driver
qlcnic: Return proper error codes from probe failure paths
tg3: Update version to 3.132
...
Refactor all TX HW workarounds into a separate routine called
be_xmit_workarounds().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.
The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.
This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Multi-function mode, all functions should be able to utilize said function;
There's no reason why only the link owner should be able to do so.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCIe advanced error recovery, the secondary bus reset will cause FW
to reset; This will cause the shared memory between it and the driver to be
invalidated.
During the driver's recovery flow, the driver should not make any assumption
on the validity of that memory and instead re-initialize it.
This also removes a redundant re-initialization of a previously
initialized mutex.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the previous unload flow, probed devices will reset the chip
in order to clean the remains of the UNDI driver.
As a result, it's possible for the FW to toggle the link.
This toggling can prove fatal, as long periods without link can cause the
filesystem mount to fail as the storage protocol timeouts. This has been
observed against particular switches with long link re-establishment time.
This patch informs FW during the reset period that the link should not
be toggled - the FW will keep it alive until some interface will load and claim
the link as its own.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize ethtool's callback `get_priv_flags' - shed more light on the
feasibility of devices as storage interfaces.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the standard DIV_ROUND_UP macro in order to provide better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checks at approprate places whether *dma_map*() call has
succeeded or not.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Reviewed-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is about using rcu_dereference() when not in a rcu-locked section. It only
happens on initialization hence fix the initialization to not rcu_dereference()
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the SMSC911X driver may only be built for a specific set of
architectures, being limited to do so by a Kconfig depends line. This
means that if a platform wishes to use the driver, its architecture must
be added to the list explicitly, introducing pointless churn.
This may have been due to the driver's use of the {read,write}s{b,w,l}
functions, which have since been replaced with the more standard
io{read,write}{8,16,32}_rep. We can instead depend on HAS_IOMEM, which
should prevent build issues while allowing the driver to be built for
currently unlisted architectures, including x86 and arm64.
This patch removes the explicit list of architectures from the driver's
depend line, and replaces it with a dependency on HAS_IOMEM.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bfd428d ("net: ethernet: sun: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e998fd4 ("net: ethernet: korina: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b0aaef ("net: ethernet: apple: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
MVF is a family while MVF600 is a particular SoC in the family. We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device. And this is how fec_dt_ids
works for all those IMX fec variants. Let's change mvf to mvf600 to
have it work in the same way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o After change in EPORT features of 82xx adapter, netdev->features needs to
be updated to reflect EPORT feature updates but driver was manipulating
netdev->features at wrong place.
o This patch uses netdev_update_features() and .ndo_fix_features() to
update netdev->features properly.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code is removed because netdev->trans_start updates made by the driver
will be ignored by the kernel.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix error paths in probe to assign proper error codes to probe return value.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resetting the device, the driver waits for a signature to be
updated to know that firmware has completed initialization. However, the
call to tg3_poll_fw() is being done too late and we're writing to the
GRC_MODE register before it has completely initialized, causing
contention with firmware. This logic has existed since day one but is
causing PCIE link to go down randomly at startup on one platform once
every few hundred reboots.
Move the tg3_poll_fw() up to before we write to the GRC_MODE register
after reset.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
The name of the pci_driver struct had to be changed in order to prevent
a build failure.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
The name of the pci_driver struct had to be changed in order to prevent
a build failure.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the SW prio_tc values at initialization to the HW setting.
Setting the SW prio_tc default values to be the HW setting by reading the
rtrup2tc register. For any TC change we need to reset the device.
This will remove the need to reset the device at the first
time we call ixgbe_dcbnl_ieee_setets.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes unused i2c function definition.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes LED issues with i210 and i211 devices, due to changes in the
device registers.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reorders disabling napi and irqs during igb_down.
This is done to avoid possible panic's found in other Intel drivers
when Rx traffic arrives while interface is going down.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where we were only checking to update checksum
on first part of nvm image. Newer parts have multiple checksum fields and
checksum function will accommodate that as long as we call it in the first
place for any changes made.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This path allows users to get appropriate flow control setting on SerDes
devices, based on original implementation for Copper devices.
Also, since 100baseFX does not support setting flow control, so exclude
it from the setting mechanism.
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for SFP modules media type discovery for
SGMII, which will enable driver to detect supported external PHYs,
including 100baseFXSFP module.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support a more accurate check for a PTP Rx hang where the
device can no longer timestamp received packets, we need to update, per
ring, when the last Rx timestamp was. Because of how the PTP Rx hang logic
works, the current logic is valid, but properly updating the ring variable
increases the accuracy of the check.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses the changes needed to make LEDs work properly with
negative logic. This implementation uses LED Invert bit to reverse the
logic issue that occurred when LEDs are driven by cathode. Keep LEDs
blinking for SerDes devices. Also made changes to magic number and the
for loop to reduce number of shifts.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue of unlocking swflag_mutex for 82574 and 82583
devices regardless of if the hw semaphore has been successfully acquired via
e1000_get_hw_semaphore_82574(). With this patch, unlocking mutex now depends
on if the hw semaphore was successfully acquired before. And 82574/82583
devices are reset regardless of whether e1000_get_hw_semaphore_82574()
returns success or failure.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
User should not be allowed to delete base function of eth port. Add a new field
to the bfa ioc attributes structure to indicate if the given ioc is default
function on the port or not.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure of the UCAST set for base mac address fails when user configures a
duplicate mac address that matches that of another vNIC on the same port.
The bna does not handle the ucast failure and keeps this address in cache.
On disable of the vNIC, bna tries to delete the failed base mac address and the
fw asserts.
On failure of ucast address, mark ucast address set to false.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver configuration flags are retained across open/stop operations preventing
configurations to be set in next open/stop. Setting MTU on a 1020 causes
network to fail until a reboot is performed on the host.
Clear the flags when configuration resets in hardware.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Device Tree support to dm9000 driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cures transmit timeout's with DHCP observed
while running under KVM. When the transmit ring is cleaned out,
the Byte Queue Limit values need to be reset.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the VIA Velocity network driver to be bound to a
OF created platform device.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>