We need to process tx descriptors for all queues (currently main tx
queue and cabq) which may have triggered the TX completion interrupt.
Otherwise, the queues can get stuck after sending a few frames.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, we would store the operating mode at interface up time,
but only update the PCU registers when the next reset happened.
The result is that if beacon configuration (ops->bss_info_changed)
happens before ops->config, we will program the wrong things into
the timer registers. Consequently, beacons won't work in AP mode
until after a reset (channel change, scan etc.).
This is fragile anyway so just program the opmode as soon as
mac80211 gives it to us.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Monotonicity of packet error rate should be kept when moving
from one phy to another (legacy to ht, ht single stream to dual,
etc). Current code skips updating per for other phys.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the lowest rate in 11na ht40 mode is 13.5Mbps this shortens the
range when compared to 11na ht20 mode where the lowest rate is 6.5Mbps.
To improve the range, make 6.5Mbps as the lowest rate in 11na ht40 mode,
this improves the range by approximately 2dB. 11ng ht40 does not have
this issue as it also has basic rates (1, 2, 5.5 and 11).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make atheros wireless drivers visible when you select
"Atheros wirless drivers". Adds links to ath.ko page,
and Atheros drivers page on the wiki.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath.ko module itself depends on cfg80211
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cancel_delayed_work_sync() and cancel_work_sync() are already being
used therefore already waiting for all pending work by the driver
to have been completed, no need to flush the mac80211 workqueue.
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be cancelling our work at the stop callback since
we are borrowing the mac80211 workqueue for our work. As it
stands mac80211 expects this for suspend purposes.
The ath9k specific virtual wiphy stuff need only be
cancelled only when the we have no secondary virtual wiphys.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this as we'll be moving the cancel elsewhere later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k uses the mac80211 workqueue for 4 different types of work:
* Led blink work
* TX hang monitoring work
* internal wiphy schedular work
* channel change work done for internal wiphy schedular
Since the internal wiphy schedular can end up kicking off some
channel channel change work we should first cancel the wiphy
schedular work and then the channel change work.
The TX hang work can be cancelled second since we're going down
anyway.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our version goes by the kernel release.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are using setpower routines regardless of the current power mode.
Don't bother the hardware, if it is not necessary.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a small window where the mac80211 changes the IEEE80211_CONF_PS
flag, and then informs the driver about the change. We have a race
condition if we are checking the flag in the same time. Avoid it by
introducing a local variable, and using that instead of checking the
IEEE80211_CONF_PS flag directly.
This fix the problem reported by Luis:
http://article.gmane.org/gmane.linux.kernel.wireless.general/34363
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix this build error when CONFIG_AR9170_LEDS is not set
drivers/net/wireless/ath/ar9170/main.c:1296: error: 'struct ar9170' has
no member named 'led_work'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup aggregation start/stop function interfaces.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TH gets 5 GHz.
Cc: David Quan <david.quan@atheros.com>
Cc: Michael Green <michael.green@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect limits leads to reads outside array bounds.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will have disabled the queues for us when
needed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new values are taken from the recently open sourced Atheros HAL.
Correctness is also confirmed by the users with access to Atheros
documentation.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a dedicated function for this kind of checks, use that
instead of duplicating the code.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are in NETWORK SLEEP state, AR_SLP32_TSF_WRITE_STATUS limit
always exceeds in 'ath9k_hw_reset_tsf', because reading of the
AR_SLP3 register always return with the magic 0xdeadbeef value.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use %pM instead, and also remove stray variables
declared with DECLARE_MAC_BUF.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This uses the new configuration changes indicated up by
mac80211 when all interfaces are marked idle. We need to do
a little more work as we have our own set of virtual
wiphys within ath9k.
Only when all virtual wiphys are inactive do we allow an idle
state change for a wiphy to trigger disabling the radio.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are changing the power mode of the chip, but this may
have unpredictable effects, if another code are trying to set the power
mode via 'ath9k_hw_setpower' in the same time from another context.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Uninline these functions before we add functional changes to them.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because ath9k_setpower is called from various contexts, we have to
protect it against concurrent calls.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update tx BA window and complete the frame as failed
one if we can't clone the holding descriptor due to
unavailability of descriptors.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
oops, this one should be part of the original patch
"ath9k: downgrade assert in ath_clone_txbuf()"
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware doesn't generate interrupts in some cases and so work
around this by monitoring the TX status periodically and reset the
chip if required.
This behavior of the hardware not generating the TX interrupts can
be noticed through ath9k debugfs interrupt statistics when heavy
traffic is being sent from STA to AP. One can easily see this behavior
when the STA is transmitting at a higher rates. The interrupt statistics
in the debugfs interface clearly shows that only RX interrupts alone
being generated and TX being stuck.
TX should be monitored through a timer and reset the chip only when
frames are queued to the hardware but TX interrupts are not generated
for the same even after one second. Also, we shouldn't remove holding
descriptor from AC queue if it happens to be the only descriptor and
schedule TX aggregation regarless of queue depth as it improves
scheduling of AMPDUs from software to hardware queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running iperf along with p2p traffic on both TX and RX side then
stop one side, then stop the other side, then start it up again,
eventually the STA gets into a mode that it can not pass data at
all.
A hardware workaround for invalid RSSI can make FIFO write pointer
to jump over read pointer, causing RX data corruption and repeated
DMA. Both TX and RX works fine when the workaround is disabled.
To replace the original hardware work around, software looks for
frames with post delimiter CRC error and mark the RSSI invalid so
that the upperlayer will not use the RSSI associated with this
frame. So disable the hardware workaround by updating the appropriate
registers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSSI reported by the RX descriptor requires little manipulation.
Manipulate and report the correct RSSI to the stack. This will
fix the improper signal levels reported by iwconfig iw dev wlanX
station dump. Also the Link Quality reported seems to be varying
(falls to zero also sometimes) when iperf is run from STA to AP.
Also use the default noise floor for now as the one reported
during the caliberation seems to be wrong.
The Signal and Link Quality before this patch (taken while TX is
in progress from STA to AP)
09:59:13.285428037 Link Quality=29/70 Signal level=-81 dBm
09:59:13.410660084 Link Quality=20/70 Signal level=-90 dBm
09:59:13.586864392 Link Quality=21/70 Signal level=-89 dBm
09:59:13.710296281 Link Quality=21/70 Signal level=-89 dBm
09:59:13.821683064 Link Quality=25/70 Signal level=-85 dBm
09:59:13.933402989 Link Quality=24/70 Signal level=-86 dBm
09:59:14.045839276 Link Quality=26/70 Signal level=-84 dBm
09:59:14.193926673 Link Quality=23/70 Signal level=-87 dBm
09:59:14.306230262 Link Quality=31/70 Signal level=-79 dBm
09:59:14.419459667 Link Quality=26/70 Signal level=-84 dBm
09:59:14.530711167 Link Quality=37/70 Signal level=-73 dBm
09:59:14.642593962 Link Quality=29/70 Signal level=-81 dBm
09:59:14.754361169 Link Quality=21/70 Signal level=-89 dBm
09:59:14.866217355 Link Quality=21/70 Signal level=-89 dBm
09:59:14.976963623 Link Quality=28/70 Signal level=-82 dBm
09:59:15.089149809 Link Quality=26/70 Signal level=-84 dBm
09:59:15.205039887 Link Quality=27/70 Signal level=-83 dBm
09:59:15.316368003 Link Quality=23/70 Signal level=-87 dBm
09:59:15.427684036 Link Quality=36/70 Signal level=-74 dBm
09:59:15.539756380 Link Quality=21/70 Signal level=-89 dBm
09:59:15.650549093 Link Quality=22/70 Signal level=-88 dBm
09:59:15.761171672 Link Quality=32/70 Signal level=-78 dBm
09:59:15.872793750 Link Quality=23/70 Signal level=-87 dBm
09:59:15.984421694 Link Quality=22/70 Signal level=-88 dBm
09:59:16.097315093 Link Quality=21/70 Signal level=-89 dBm
The link quality and signal level after this patch (take while
TX is in progress from STA to AP)
17:21:25.627848091 Link Quality=65/70 Signal level=-45 dBm
17:21:25.762805607 Link Quality=65/70 Signal level=-45 dBm
17:21:25.875521888 Link Quality=66/70 Signal level=-44 dBm
17:21:25.987468448 Link Quality=66/70 Signal level=-44 dBm
17:21:26.100628151 Link Quality=66/70 Signal level=-44 dBm
17:21:26.213129671 Link Quality=66/70 Signal level=-44 dBm
17:21:26.324923070 Link Quality=65/70 Signal level=-45 dBm
17:21:26.436831357 Link Quality=65/70 Signal level=-45 dBm
17:21:26.610356973 Link Quality=65/70 Signal level=-45 dBm
17:21:26.723340047 Link Quality=65/70 Signal level=-45 dBm
17:21:26.835715293 Link Quality=64/70 Signal level=-46 dBm
17:21:26.949542748 Link Quality=64/70 Signal level=-46 dBm
17:21:27.062261613 Link Quality=65/70 Signal level=-45 dBm
17:21:27.174511563 Link Quality=64/70 Signal level=-46 dBm
17:21:27.287616232 Link Quality=64/70 Signal level=-46 dBm
17:21:27.400598119 Link Quality=64/70 Signal level=-46 dBm
17:21:27.511381404 Link Quality=64/70 Signal level=-46 dBm
17:21:27.624530421 Link Quality=65/70 Signal level=-45 dBm
17:21:27.737807109 Link Quality=64/70 Signal level=-46 dBm
17:21:27.850861352 Link Quality=65/70 Signal level=-45 dBm
17:21:27.963369436 Link Quality=64/70 Signal level=-46 dBm
17:21:28.076582289 Link Quality=64/70 Signal level=-46 dBm
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move its only member (u8 per) to struct ath_rate_priv.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of rssi reduce interval.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k rate control is based on only PER (packet error rate),
remove unused code which was intented to do rssi based rate
selection.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland