Improve the Kconfig help text of the follwing i2c drivers:
* busses/i2c-pca-isa.c
* chips/pcf8574.c
* chips/pcf8591.c
These are hard to detect and building them into the kernel
results in long delays at boot.
March 2006, thread "I2C_PCA_ISA causes boot delays"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114360399415744&w=2
April 2006, thread "i2c-related 1-minute hang during bootup"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114640992330721&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the ST m41t81 and m41t85 i2c rtc chips
to the existing m41t00 driver.
Since there is no way to reliably determine what type of rtc chip
is in use, the chip type is passed in via platform_data. The i2c
address and square wave frequency are passed in via platform_data
as well. To accommodate the use of platform_data, a new header
file include/linux/m41t00.h has been added.
The m41t81 and m41t85 chips halt the updating of their time registers
while they are being accessed. They resume when a stop condition
exists on the i2c bus or when non-time related regs are accessed.
To make the best use of that facility and to make more efficient
use of the i2c bus, this patch replaces multiple i2c_smbus_xxx calls
with a single i2c_transfer call.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does some cleanup to the m41t00 i2c/rtc driver including:
- use BCD2BIN/BIN2BCD instead of BCD_TO_BIN/BIN_TO_BCD
- use strlcpy instead of strncpy
- some whitespace cleanup
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the bitmasks used when writing to the M41T00 registers.
The original code used a mask of 0x7f when writing to each register,
this is incorrect and probably the result of a copy-paste error. As a
result years from 1980 to 1999 will be read back as 2000 to 2019.
Signed-off-by: David Barksdale <amatus@ocgnet.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The m41t00 i2c/rtc driver currently uses a tasklet to schedule
interrupt-level writes to the rtc. This patch causes the driver
to use a workqueue instead.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A tasklet is not suitable for what the ds1374 driver does: neither sleeping
nor mutex operations are allowed in tasklets, and ds1374_set_tlet may do
both.
We can use a workqueue instead, where both sleeping and mutex operations
are allowed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, completely optional, removes from drivers/i2c/chips all the
drivers that are implemented in the new RTC subsystem.
It should be noted that none of the current driver is actually integrated,
i.e. usable without further patches.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drop unused rogue i2c driver ID and nonsensical i2c class.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
semaphore to mutex conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below converts a few i2c semaphores to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the miscellaneaous i2c chip drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate of BCD macros.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add code to handle case where board firmware does not start the
RTC.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix BCD value errors when month=9, moving the increment inside the
BIN2BCD macro.
Fix similar code for the weekday value, just for consistency.
This bug was reported by Michael Burian <dynmail1@gassner-waagen.at>.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix functions declared static and then implemented
without the static in drivers/i2c/chips.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
eeprom_detect is first declared static and then when
the function is actually implemented, there is no static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc+memset in all remaining i2c bus and
chip drivers.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver for the Xicor X1205 RTC chip.
Signed-off-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the .owner field for various struct xxxx_driver variables,
other than pci_driver.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C_DF_NOTIFY is an i2c_driver flag, using it as an i2c_client flag
doesn't make any sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop I2C_SMBUS_I2C_BLOCK_MAX, use I2C_SMBUS_BLOCK_MAX instead.
I2C_SMBUS_I2C_BLOCK_MAX has always been defined to the same value as
I2C_SMBUS_BLOCK_MAX, and this will never change: setting it to a lower
value would make no sense, setting it to a higher value would break
i2c_smbus_data compatibility. There is no point in changing
i2c_smbus_data to support larger block transactions in SMBus mode, as
no SMBus hardware supports more than 32 byte blocks. Thus, for larger
transactions, direct I2C transfers are the way to go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 24RF08 corruption would better be prevented at i2c-core level than
at chip driver level, for several reasons:
* The second quick write should happen as soon as possible after the
first one, so as to limit the risk that another command is issued on
the bus inbetween, causing the corruption.
* As a matter of fact, the protection code at driver level was reworked
at least three times already, which proves how hard it is to get it
right there, while it's straightforward at i2c-core level.
* It's easy to add a new driver that would need the protection, and
forget to add it. This did happen already.
* As additional probing addresses can be passed to most i2c chip drivers
as module parameters, virtually every i2c chip driver would need the
protection if we want to be really safe.
* Why duplicate code when we can easily avoid it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for kind-forced addresses to i2c_probe, like i2c_detect
has for (essentially) hardware monitoring drivers.
Note that this change will slightly increase the size of the drivers
using I2C_CLIENT_INSMOD, with no immediate benefit. This is a
requirement if we want to merge i2c_probe and i2c_detect though, and
seems a reasonable price to pay in comparison with the previous
cleanups which saved much more than that (such as the i2c-isa cleanup
or the i2c address ranges removal.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill normal_isa in header files, documentation and all chip drivers, as
it is no more used.
normal_i2c could be renamed to normal, but I decided not to do so at the
moment, so as to limit the number of changes. This might be done later
as part of the i2c_probe/i2c_detect merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove an unused local variable and change the subclient name.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the inline function kobj_to_i2c_client() from max6875.c to i2c.h.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an update to the max6875 driver.
It no longer does any detection, so the address must be forced on module load.
It only makes available the user EEPROM (read-only).
This patch is based off 2.6.13-rc2-mm2.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't
complete. For one thing, the additional quick write should happen as soon
as possible and unconditionally, while both drivers had error paths before.
For another, when a given chip is forced, the core does not emit a quick
write, so a second quick write would cause the corruption rather than
prevent it.
I plan to move the corruption prevention in the core in the long run, so
that individual drivers don't have to care anymore. But I need to merge
i2c_probe and i2c_detect before I do (work in progress).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DS1339 manual, page 6, chapter Date and time operation:
The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the
hours register is defined as the 12-hour or 24-hour mode-select bit.
When high, the 12-hour mode is selected.
Patch below makes ds1337 driver work as documented in manual.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Part 2: Move the driver files themselves.
Note that the patch "adds trailing whitespace", because it does move the
files as-is, and some files happen to have trailing whitespace.
From: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Thu, Jun 30, 2005 at 11:47:09PM +0200, Sebastian Pigulak wrote:
> I've tried patching linux-2.6.13-RC1 with patch-2.6.13-rc1-git2 and
> building atxp1(it allows Vcore voltage changing) into the kernel.
> Unfortunately, the kernel compilation stops with:
>
> LD init/built-in.o
> LD vmlinux
> drivers/built-in.o(.text+0x92298): In function `atxp1_detect':
> : undefined reference to `i2c_which_vrm'
> drivers/built-in.o(.text+0x921ae): In function `atxp1_attach_adapter':
> : undefined reference to `i2c_detect'
> make: *** [vmlinux] B??d 1
> ==> ERROR: Build Failed. Aborting...
>
> Could someone have a look at the module and possibly fix it up?
SENSORS_ATXP1 must select I2C_SENSOR.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simple patch drops an out-of-date comment in the eeprom i2c chip
driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a simple path fixing an incorrect kfree in the m41t00 i2c chip
driver. The current code happens to work by accident, but the freed
pointer isn't the one which was allocated in the first place, which
could cause problems later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare