Add DPTF battery participant ACPI ID for platforms based on the Intel
TigerLake SoC.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver adds support for Dynamic Platform and Thermal Framework
battery participant device support.
These attributes are presented via sysfs interface under the platform
device for the battery participant:
$ls /sys/bus/platform/devices/INT3532:00/dptf_battery
current_discharge_capbility_ma
max_platform_power_mw
no_load_voltage_mv
high_freq_impedance_mohm
max_steady_state_power_mw
Refer to the documentation at
Documentation/ABI/testing/sysfs-platform-dptf
for details.
Here the implementation reuses existing dptf-power.c as the motivation and
processing is same. It also shares one ACPI method. Here this change is
using participant type, "PTYP" method to identify and do different
processing. By using participant type, create/delete either "dptf_power"
or "dptf_battery" attribute group and send notifications.
The particpant type for for the battery participant is 0x0C.
ACPI methods description:
PMAX (Intel(R) Dynamic Tuning Platform Max Power Supplied by Battery):
This object evaluates to the maximum platform power that can be supported
by the battery in milli watts.
PBSS (Intel(R) Dynamic Tuning Power Battery Steady State):
This object returns the max sustained power for battery in milli watts.
RBHF (Intel(R) Dynamic Tuning High Frequency Impedance):
This object returns high frequency impedance value that can be obtained
from battery fuel gauge.
VBNL (Intel(R) Dynamic Tuning No-Load Voltage)
This object returns battery instantaneous no-load voltage that can be
obtained from battery fuel gauge in milli volts
CMPP (Intel(R) Dynamic Tuning Current Discharge Capability)
This object returns battery discharge current capability obtained from
battery fuel gauge milli amps.
Notifications:
0x80: PMAX change. Used to notify Intel(R)Dynamic Tuning Battery
participant driver when the PMAX has changed by 250mw.
0x83: PBSS change. Used to notify Intel(R) Dynamic Tuning Battery
participant driver when the power source has changed.
0x85: RBHF change. Used to notify Intel(R)Dynamic Tuning Battery
participant driver when the RBHF has changed over a threshold by
5mOhm.
0x86: Battery Capability change. Used to notify Intel(R)Dynamic Tuning
Battery participant driver when the battery capability has changed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add two additional attributes to the existing power participant driver:
rest_of_platform_power_mw: (RO) Shows the rest of worst case platform
power in mW outside of S0C. This will help in power distribution to SoC
and rest of the system. For example on a test system, this value is 2.5W
with a 15W TDP SoC. Based on the adapter rating (adapter_rating_mw), user
space software can decide on proper power allocation to SoC to improve
short term performance via powercap/RAPL interface.
prochot_confirm: (WO) Confirm EC about a prochot notification.
Also userspace is notified via sysfs_notify(), whenever power source or
rest of the platform power is changed. So user space can use poll()
system call on those attributes.
The ACPI methods used in this patch are as follows:
PROP
This object evaluates to the rest of worst case platform power in mW.
Bits:
23:0 Worst case rest of platform power in mW.
PBOK
PBOK is a method designed to provide a mechanism for OSPM to change power
setting before EC can de-assert a PROCHOT from a device. The EC may
receive several PROCHOTs, so it has a sequence number attached to PSRC
(read via existing attribute "platform_power_source"). Once OSPM takes
action for a PSRC change notification, it can call PBOK method to confirm
with the sequence number.
Bits:
3:0 Power Delivery State Change Sequence number
30 Reserved
31 0 – Not OK to de-assert PROCHOT
1 – OK to de-assert PROCHOT
PSRC (Platform Power Source): Not new in this patch but for
documentation for new bits
This object evaluates to an integer that represents the system power
source as well as the power delivery state change sequence number.
Bits:
3:0 The current power source as an integer for AC, DC, USB, Wireless.
0 = DC, 1 = AC, 2 = USB, 3 = Wireless Charging
7:4 Power Delivery State Change Sequence Number. Default value is 0
Notifications:
0x81: (Power State Change) Used to notify when the power source has
changed.
0x84: (PROP change) Used to notify when the platform rest of power has
changed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject, minor ABI documentation edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tiger Lake's new unique ACPI device IDs for DPTF and fan drivers are not
valid as the IDs are missing 'C'. Fix the IDs by updating them.
After the update, the new IDs should now look like
INT1047 --> INTC1047
INT1040 --> INTC1040
INT1043 --> INTC1043
INT1044 --> INTC1044
Fixes: 55cfe6a5c5 ("ACPI: DPTF: Add Tiger Lake ACPI device IDs")
Fixes: c248dfe7e0 ("ACPI: fan: Add Tiger Lake ACPI device ID")
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tiger Lake has new unique ACPI device IDs that need to be added to the
DPTF drivers to support it.
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Skip conversion to platform_device and use dev_get_drvdata() directly.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is too much to add extra header search path for all files in
drivers/acpi/dptf/.
Fix up one C file, and remove the header search path.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
904 496 0 1400 578 drivers/acpi/dptf/dptf_power.o
File size After adding 'const':
text data bss dec hex filename
944 432 0 1376 560 drivers/acpi/dptf/dptf_power.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have a couple of drivers, acpi_apd.c and acpi_lpss.c,
that need to pass extra build-in properties to the devices
they create. Previously the drivers added those properties
to the struct device which is member of the struct
acpi_device, but that does not work. Those properties need
to be assigned to the struct device of the platform device
instead in order for them to become available to the
drivers.
To fix this, this patch changes acpi_create_platform_device
function to take struct property_entry pointer as parameter.
Fixes: 20a875e2e8 (serial: 8250_dw: Add quirk for APM X-Gene SoC)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since DPTF has its own folder under ACPI, move this file also there.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver adds support for Dynamic Platform and Thermal Framework
(DPTF) Platform Power Participant device (INT3407) support.
This participant is responsible for exposing platform telemetry such as:
max_platform_power
platform_power_source
adapter_rating
battery_steady_power
charger_type
These attributes are presented via sysfs interface under the INT3407
platform device:
$ls /sys/bus/platform/devices/INT3407\:00/dptf_power/
adapter_rating_mw
battery_steady_power_mw
charger_type
max_platform_power_mw
platform_power_source
`
ACPI methods description used in this driver:
PMAX: Maximum platform power that can be supported by the battery in
mW.
PSRC: System charge source,
0x00 = DC
0x01 = AC
0x02 = USB
0x03 = Wireless Charger
ARTG: Adapter rating in mW (Maximum Adapter power) Must be 0 if no
AC adapter is plugged in.
CTYP: Charger Type,
Traditional : 0x01
Hybrid: 0x02
NVDC: 0x03
PBSS: Returns max sustained power for battery in milliWatts.
The INT3407 also contains _BTS and _BIX objects, which are compliant to
ACPI 5.0, specification. Those objects are already used by ACPI battery
(PNP0C0A) driver and information about them is exported via Linux power
supply class registration.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>