Update the ep93xx i2c support:
1) The platform init code passes the configuration data for the
i2c-gpio driver. This allows any gpio pin do be used for the
sda and scl pins. It also allows the platform to specify the
udelay and timeout.
2) Program the gpio configuration register to enable/disable the
open drain drivers. Note that this really only works if the
sda and scl pins are set to EP93XX_GPIO_LINE_EEDAT and
EP93XX_GPIO_LINE_EECLK.
3) Update the edb93xx.c platform init to use the new support.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of the EP93XX_GPIO_*_INT_* register defines in ep93xx-regs.h
not required due to how the ep93xx core and gpiolib support handle
gpio interrupts. Remove the defines to prevent future confusion.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: convert to GENERIC_HARDIRQS_NO__DO_IRQ
Blackfin: drop all simple-gpio board resources
Blackfin: fix framebuffer mmap bug for nommu
Blackfin: includecheck fix: mach-bf548, ezkit.c
Blackfin: drop cs_change_per_word setting
Blackfin: bf533-ezkit: convert to physmap/jedec_probe
Blackfin: convert adv7393 resources to new i2c framework
Blackfin: fix missed cache config renames
Blackfin: cplbinfo: drop d_path() hacks
Blackfin: asm/irq.h: pull in mach/anomaly.h for anomaly defines
Blackfin: BF51x: add PTP MMR defines
Blackfin: mass clean up of copyright/licensing info
Blackfin: convert to use arch_gettimeoffset()
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Don't allocate smaller sized mappings on every iteration
sh: Try PMB mapping based on physical address, not mapping size
sh: Plug PMB alloc memory leak
sh: Sprinkle __uses_jump_to_uncached
sh: enable sleep state LEDs on Ecovec24
usb: r8a66597-udc unaligned fifo fix
sh: mach-ecovec24: Document DS2 switch settings.
sh: Build fix: export __movmem
sh: Disable unaligned kernel access printks by default.
sh: mach-ecovec24: modify 1st MTD area to read only
sh: mach-ecovec24: Add TouchScreen support
sh: magicpanelr2 and dreamcast can use the generic I/O base.
sh: Don't enable interrupts in the page fault path
sh: Set the default I/O port base to P2SEG.
sh: Handle ioport_map() cases for >= P1SEG addresses.
This reverts commit 9bcbdd9c58.
The real bug producing LatencyTop latencies has been fixed in:
f5dc375: sched: Update the clock of runqueue select_task_rq() selected
And the commit being reverted here triggers local timer processing
from every device IRQ. If device IRQs come in at a high frequency,
this could cause a performance regression.
The commit being reverted here purely 'fixed' the reported latency
as a side effect, because CPUs were being moved out of idle more
often.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091008064041.67219b13@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, we've got the less than ideal situation where if we need to
allocate a 256MB mapping we'll allocate four entries like so,
entry 1: 128MB
entry 2: 64MB
entry 3: 16MB
entry 4: 16MB
This is because as we execute the loop in pmb_remap() we will
progressively try mapping the remaining address space with smaller and
smaller sizes. This isn't good because the size we use on one iteration
may be the perfect size to use on the next iteration, for instance when
the initial size is divisible by one of the PMB mapping sizes.
With this patch, we now only need two entries in the PMB to map 256MB of
address space,
entry 1: 128MB
entry 2: 128MB
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We should favour PMB mappings when the physical address cannot be
reached with 29-bits.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If we fail to allocate a PMB entry in pmb_remap() we must remember to
clear and free any PMB entries that we may have previously allocated,
e.g. if we were allocating a multiple entry mapping.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix some callers of jump_to_uncached() and back_to_cached() that were
not annotated with __uses_jump_to_uncached.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the ecovec24 board code to enable Power
Management LEDs showing the current sh7724 sleep state.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add text in feature-removal.txt indicating that VMI will be removed in
the 2.6.37 timeframe.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
LKML-Reference: <1254193238.13456.48.camel@ank32.eng.vmware.com>
[ removed a bogus Kconfig change, marked (DEPRECATED) in Kconfig ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sparc-perf-events-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mm, perf_event: Make vmalloc_user() align base kernel virtual address to SHMLBA
perf_event: Provide vmalloc() based mmap() backing
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, timers: Check for pending timers after (device) interrupts
NOHZ: update idle state also when NOHZ is inactive
Now that range timers and deferred timers are common, I found a
problem with these using the "perf timechart" tool. Frans Pop also
reported high scheduler latencies via LatencyTop, when using
iwlagn.
It turns out that on x86, these two 'opportunistic' timers only get
checked when another "real" timer happens. These opportunistic
timers have the objective to save power by hitchhiking on other
wakeups, as to avoid CPU wakeups by themselves as much as possible.
The change in this patch runs this check not only at timer
interrupts, but at all (device) interrupts. The effect is that:
1) the deferred timers/range timers get delayed less
2) the range timers cause less wakeups by themselves because
the percentage of hitchhiking on existing wakeup events goes up.
I've verified the working of the patch using "perf timechart", the
original exposed bug is gone with this patch. Frans also reported
success - the latencies are now down in the expected ~10 msec
range.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Frans Pop <elendil@planet.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <20091008064041.67219b13@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
agp: parisc-agp.c - use correct page_mask function
parisc: Fix linker script breakage.
parisc: convert to asm-generic/hardirq.h
parisc: Make THREAD_SIZE available to assembly files and linker scripts.
parisc: correct use of SHF_ALLOC
parisc: rename parisc's vmalloc_start to parisc_vmalloc_start
parisc: add me to Maintainers
parisc: includecheck fix: signal.c
parisc: HAVE_ARCH_TRACEHOOK
parisc: add skeleton syscall.h
parisc: stop using task->ptrace for {single,block}step flags
parisc: split syscall_trace into two halves
parisc: add missing TI_TASK macro in syscall.S
parisc: tracehook_signal_handler
parisc: tracehook_report_syscall
Blackfin already sets proper flow handlers on all IRQs, and we don't rely
on __do_IRQ, therefore we can simply select GENERIC_HARDIRQS_NO__DO_IRQ.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The simple-gpio has been replaced by the gpio sysfs interface, so drop the
unused simple-gpio resources from all Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The patch added a special get_unmapped_area for framebuffer which
was hooked to the file ops in drivers/video/fbmem.c.
This is needed since v2.6.29-rc1 where nommu vma management was
updated, and mmap of framebuffer caused kernel BUG panic. You may turn
on "Debug the global anon/private NOMMU mapping region tree" config to
such message.
As Documentation/nommu-mmap.txt said,
"To provide shareable character device support, a driver must provide
a file->f_op->get_unmapped_area() operation. The mmap() routines will
call this to get a proposed address for the mapping."
With this change, user space should call mmap for framebuffer using
shared map. Or it can try shared map first, then private map if
failed. This shared map usage is now consistent between mmu and nommu.
The sys_ file may not be a good place for this patch. But there is a
similar one for sparc. I tested a similar patch on nios2nommu, though
I don't have a blackfin board to test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix the following 'make includecheck' warning:
arch/blackfin/mach-bf548/boards/ezkit.c: linux/input.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Structs get initialized to 0 already, and we want to punt this field, so
scrub it from all of our boards.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the common jedec_probe supports the ST PSD4256G6V, no need to
use the custom stm_flash driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the driver has been updated, convert the board resources to the
new i2c framework for managing slaves.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Change the #define's for the EP93XX_*_PHYS_BASE addresses to use
macros for easier readability.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Contec Micro9-Slim support
Cc: Ryan Mallon <ryan@bluewatersys.com>
Requires: 5750/1
Signed-off-by: Hubert Feurstein <hubert.feurstein@contec.at>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both iPaqs h3100 and h3600 currently share the same source
file - h3600.c But Makefile builds it only if CONFIG_SA1100_H3600
selected, so selecting just CONFIG_SA1100_H3100 results in
"no machine record defined" message and aborted compilation.
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the warning messages during kernel build for bcmring.
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If sparsemem is enabled, the start_pfn passed to the free_memmap()
function corresponds to an area of memory not known to the kernel and
pfn_to_page returns a wrong value. The (start_pfn - 1), however, is
known to the kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is needed because applications using the sys_cacheflush system call
can pass a memory range which isn't mapped yet even though the
corresponding vma is valid. The patch also adds unwinding annotations
for correct backtraces from the coherent_user_range() functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Ryan Mallon <ryan@bluewatersys.com>
Change the gpio_to_irq and irq_to_gpio static inline functions to
macros so that they can be used in variable initialisers.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the missing Kconfig options for the first SDRAM bank address
on ep93xx boards.
Cc: Hubert Feurstein <(address hidden)>
Signed-off-by: H Hartley Sweeten <(address hidden)>
Acked-by: Ryan Mallon <(address hidden)>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Looks like the big Kconfig cache split/rename missed one spot in the SMP
cache lock headers.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The cplbinfo was using d_path() to figure out which cpu/cplb was being
parsed. As Al pointed out, this isn't exactly reliable as it assumes the
static VFS path to be unchanged, and it's just poor form. So use the
proc_create_data() to properly (and internally) pass the exact cpu/cplb
requested to the parser function.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The asm/irq.h header uses anomaly defines, but doesn't make sure to
explicitly include the anomaly header for them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.
It also removes:
- verbose GPL text(refer to the top level ./COPYING file)
- file names (you are looking at the file)
- bug url (it's in the ./MAINTAINERS file)
- "or later" on GPL-2, when we did not have that right
It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert Blackfin to use GENERIC_TIME via the arch_getoffset()
infrastructure, reducing the amount of arch specific code we need to
maintain.
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
I was using Coccinelle with the mutex_unlock semantic patch, and it
unconvered this problem. It appears to be a valid missing unlock issue.
This change should correct it by moving the unlock below the label.
This patch is against the mainline kernel.
Cc: Julia Lawall <julia@diku.dk>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
the original flush operation is to flush the function address which is
copied from.
But we do not change the function code and it is not necessary to flush it.
Signed-off-by: janboe <janboe.ye@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some architectures such as Sparc, ARM and MIPS (basically
everything with flush_dcache_page()) need to deal with dcache
aliases by carefully placing pages in both kernel and user maps.
These architectures typically have to use vmalloc_user() for this.
However, on other architectures, vmalloc() is not needed and has
the downsides of being more restricted and slower than regular
allocations.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: David Miller <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1254830228.21044.272.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds an EX_TABLE entry to mvc{p|s|os} usercopy functions that
may be called with KERNEL_DS. In combination with collaborative memory
management, kernel pages marked as unused may trigger an adressing exception
in the usercopy functions. This fixes an unhandled addressing exception bug
where strncpy_from_user() is used with len > strnlen and KERNEL_DS, crossing
a page boundary to an unused page.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used address 0x1084 instead of 0x84 to store the suspend CPU address.
With this patch we use the correct address 0x84 as it is defined in
the POP.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The time a system has been suspended should not show up in any
of the cputime accounting fields. The time of inactivity is definitly
not any form of real cputime nor is it idle time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The function graph tracer used to have a protection against NMI
while entering a function entry tracing. But this is useless now,
the tracer is reentrant and the ring buffer supports NMI tracing.
Same as 07868b086c for x86.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The system call takes a signed length parameter. So perform sign
extension instead of zero extension.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use an own implementation instead of the common code udelay loop.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When udelay() gets called with a delay that would expire before the
next clock event it reprograms the clock comparator.
When the interrupt happens the clock comparator won't be resetted
therefore the interrupt condition doesn't get cleared.
The result is an endless timer interrupt loop until the next clock
event would expire (stored in lowcore).
So udelay() usually would wait much longer for small delays than it
should.
Fix this by disabling the local tick which makes sure that the clock
comparator will be resetted when a timer interrupt happens.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 version of module_frob_arch_sections allocates additional
syminfos for got and plt offsets. These syminfos are freed on
sucessful module load. If the module fails to load (e.g. missing
dependency when using insmod instead of modprobe) this area is not
freed.
This patch lets module_free free this area. Please note, we have to
set the pointer to NULL since module_free is called several times
from the generic code.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Also increase the maximum possible kmemleak early log entries since
2000 are not sufficient on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
next-20090925 randconfig build breaks on s390x, with CONFIG_AIO=n.
arch/s390/mm/pgtable.c: In function 's390_enable_sie':
arch/s390/mm/pgtable.c:282: error: 'struct mm_struct' has no member named 'ioctx_list'
arch/s390/mm/pgtable.c:298: error: 'struct mm_struct' has no member named 'ioctx_list'
make[1]: *** [arch/s390/mm/pgtable.o] Error 1
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The original driver was written with the KEY() macro defined as (col,
row) instead of (row, col) as defined by the matrix keypad
infrastructure. So the keymap was defined accordingly. Since the
driver that was merged upstream uses the matrix keypad infrastructure,
modify the keymap accordingly.
While we are at it, fix the comments in twl4030.h and define
PERSISTENT_KEY as (r,c) instead of (c, r)
Tested on a RX51 (N900) device.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Lock DPLL5 at 120MHz at boot. The USBHOST 120MHz f-clock and
USBTLL f-clock are the only users of this DPLL, and 120MHz is
is the only recommended rate for these clocks.
With this patch, the 60 MHz ULPI clock is generated correctly.
Tested on an OMAP3430 SDP.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cd92204924 added
support for omap850. However, the patch accidentally
removed the wrong ifdef:
# define cpu_is_omap730() 1
# endif
#endif
+#else
+# if defined(CONFIG_ARCH_OMAP850)
+# undef cpu_is_omap850
+# define cpu_is_omap850() 1
+# endif
+#endif
...
void omap2_check_revision(void);
#endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */
-
-#endif
Instead of removing removing the #endif at the end of the file,
the #endif before #else should have been removed.
But we cannot have multiple #else statements as pointed out by
Alistair Buxton <a.j.buxton@gmail.com>. So the fix is to:
- remove the non-multi-omap special handling, as we need to
detect between omap730 and omap850 anyways.
- add the missing #endif back to the end of the file
Reported-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add support for change_pte mmu notifiers
KVM: MMU: add SPTE_HOST_WRITEABLE flag to the shadow ptes
KVM: MMU: dont hold pagecount reference for mapped sptes pages
KVM: Prevent overflow in KVM_GET_SUPPORTED_CPUID
KVM: VMX: flush TLB with INVEPT on cpu migration
KVM: fix LAPIC timer period overflow
KVM: s390: fix memsize >= 4G
KVM: SVM: Handle tsc in svm_get_msr/svm_set_msr correctly
KVM: SVM: Fix tsc offset adjustment when running nested
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Clear sticky FSR register after saving it to func parametr
microblaze: UMS is used only for MMU kernel
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: using HZ needs an include of linux/param.h
sparc32: convert to asm-generic/hardirq.h
sparc64: Cache per-cpu %pcr register value in perf code.
sparc64: Fix comment typo in perf_event.c
sparc64: Minor coding style fixups in perf code.
sparc64: Add a basic conflict engine in preparation for multi-counter support.
sparc64: Increase vmalloc size to fix percpu regressions.
sparc64: Add initial perf event conflict resolution and checks.
sparc: Niagara1 perf event support.
sparc: Add Niagara2 HW cache event support.
sparc: Support all ultra3 and ultra4 derivatives.
sparc: Support HW cache events.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix rename of pt_regs offset defines breakage
m68knommu: remove duplicated #include
m68knommu: show KiB rather than pages in "Freeing initrd memory:" message
The 'pwrdm_for_each()' function walks powerdomains with a spinlock
locked, so the the callbacks cannot do anything which may sleep.
This patch introduces a 'pwrdm_for_each_nolock()' helper which does
the same, but without the spinlock locked. This fixes the following
lockdep warning:
[ 0.000000] WARNING: at kernel/lockdep.c:2460 lockdep_trace_alloc+0xac/0xec()
[ 0.000000] Modules linked in:
(unwind_backtrace+0x0/0xdc) from [<c0045464>] (warn_slowpath_common+0x48/0x60)
(warn_slowpath_common+0x48/0x60) from [<c0067dd4>] (lockdep_trace_alloc+0xac/0xec)
(lockdep_trace_alloc+0xac/0xec) from [<c009da14>] (kmem_cache_alloc+0x1c/0xd0)
(kmem_cache_alloc+0x1c/0xd0) from [<c00b21d8>] (d_alloc+0x1c/0x1a4)
(d_alloc+0x1c/0x1a4) from [<c00a887c>] (__lookup_hash+0xd8/0x118)
(__lookup_hash+0xd8/0x118) from [<c00a9f20>] (lookup_one_len+0x84/0x94)
(lookup_one_len+0x84/0x94) from [<c010d12c>] (debugfs_create_file+0x8c/0x20c)
(debugfs_create_file+0x8c/0x20c) from [<c010d320>] (debugfs_create_dir+0x1c/0x20)
(debugfs_create_dir+0x1c/0x20) from [<c000e8cc>] (pwrdms_setup+0x60/0x90)
(pwrdms_setup+0x60/0x90) from [<c002e010>] (pwrdm_for_each+0x30/0x80)
(pwrdm_for_each+0x30/0x80) from [<c000e79c>] (pm_dbg_init+0x7c/0x14c)
(pm_dbg_init+0x7c/0x14c) from [<c00232b4>] (do_one_initcall+0x5c/0x1b8)
(do_one_initcall+0x5c/0x1b8) from [<c00083f8>] (kernel_init+0x90/0x10c)
(kernel_init+0x90/0x10c) from [<c00242c4>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, only GPIOs in the wakeup domain (GPIOs in bank 0) are
enabled as wakups. This patch also enables GPIOs in the PER
powerdomain (banks 2-6) to be used as possible wakeup sources.
In addition, this patch ensures that all GPIO wakeups can wakeup
the MPU using the PM_MPUGRPSEL_<pwrdm> registers.
NOTE: this doesn't enable the individual GPIOs as wakeups, this simply
enables the per-bank wakeups at the powerdomain level.
This problem was discovered by Mike Chan when preventing the CORE
powerdomain from going into retention/off. When CORE was allowed to
hit retention, GPIO wakeups via IO pad were working fine, but when
CORE remained on, GPIO module-level wakeups were not working properly.
To test, prevent CORE from going inactive/retention/off, thus
preventing the IO chain from being armed:
# echo 3 > /debug/pm_debug/core_pwrdm/suspend
This ensures that GPIO wakeups happen via module-level wakeups and
not via IO pad.
Tested on 3430SDP using the touchscreen GPIO (gpio 2, in WKUP)
Tested on Zoom2 using the QUART interrup GPIO (gpio 102, in PER)
Also, c.f. OMAP PM wiki for troubleshooting GPIO wakeup issues:
http://elinux.org/OMAP_Power_Management
Reported-by: Mike Chan <mikechan@google.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
USBHOST module has 2 fclocks (for HOST1 and HOST2), only one iclock
and only a single bit in the WKST register to indicate a wakeup event.
Because of the single WKST bit, we cannot know whether a wakeup event
was on HOST1 or HOST2, so enable both fclocks before clearing the
wakeup event to ensure both hosts can properly clear the event.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Clearing wakeup sources is now only done when the PRM indicates a
wakeup source interrupt. Since we don't handle any other types of
PRCM interrupts right now, warn if we get any other type of PRCM
interrupt. Either code needs to be added to the PRCM interrupt
handler to react to these, or these other interrupts should be masked
off at init.
Updated after Jon Hunter's PRCM IRQ rework by Kevin Hilman.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
PM_WKST register contents should be ANDed with the contents of the
MPUGRPSEL registers. Otherwise the MPU PRCM interrupt handler could
wind up clearing wakeup events meant for the IVA PRCM interrupt
handler. A future revision to this code should be to read a cached
version of MPUGRPSEL from the powerdomain code, since PRM reads are
relatively slow.
Updated after Jon Hunter's PRCM IRQ change by Kevin Hilman
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are two scenarios where a race condition could result in a hang
in the prcm_interrupt handler. These are:
1). Waiting for PRM_IRQSTATUS_MPU register to clear.
Bit 0 of the PRM_IRQSTATUS_MPU register indicates that a wake-up event
is pending for the MPU. This bit can only be cleared if the all the
wake-up events latched in the various PM_WKST_x registers have been
cleared. If a wake-up event occurred during the processing of the prcm
interrupt handler, after the corresponding PM_WKST_x register was
checked but before the PRM_IRQSTATUS_MPU was cleared, then the CPU
would be stuck forever waiting for bit 0 in PRM_IRQSTATUS_MPU to be
cleared.
2). Waiting for the PM_WKST_x register to clear.
Some power domains have more than one wake-up source. The PM_WKST_x
registers indicate the source of a wake-up event and need to be cleared
after a wake-up event occurs. When the PM_WKST_x registers are read and
before they are cleared, it is possible that another wake-up event
could occur causing another bit to be set in one of the PM_WKST_x
registers. If this did occur after reading a PM_WKST_x register then
the CPU would miss this event and get stuck forever in a loop waiting
for that PM_WKST_x register to clear.
This patch address the above race conditions that would result in a
hang.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
According to the following in arch/arm/mm/fault.c page faults from
kernel mode are invalid if mmap_sem is already held and there is
no exception handler defined for the faulting instruction:
/*
* As per x86, we may deadlock here. However, since the kernel only
* validly references user space from well defined areas of the code,
* we can bug out early if this is from code which shouldn't.
*/
if (!down_read_trylock(&mm->mmap_sem)) {
if (!user_mode(regs) && !search_exception_tables(regs->ARM_pc))
goto no_context;
Since mmap_sem can be held at arbitrary times by another thread this
also means that any page faults from kernel mode are invalid if no
exception handler is defined for them, regardless whether mmap_sem is
held at the time of fault.
To easier detect code that can trigger the above error, add a check
also for the case where mmap_sem is acquired. As this has an overhead
make it a VM debug check.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previous patch d63678d607d0e37ec7abe5ceb545d7e8aab956a4 clear
it for noMMU kernel. This one do it for MMU.
Correct noMMU version
Signed-off-by: Michal Simek <monstr@monstr.eu>
this is needed for kvm if it want ksm to directly map pages into its
shadow page tables.
[marcelo: cast pfn assignment to u64]
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
this flag notify that the host physical page we are pointing to from
the spte is write protected, and therefore we cant change its access
to be write unless we run get_user_pages(write = 1).
(this is needed for change_pte support in kvm)
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When using mmu notifiers, we are allowed to remove the page count
reference tooken by get_user_pages to a specific page that is mapped
inside the shadow page tables.
This is needed so we can balance the pagecount against mapcount
checking.
(Right now kvm increase the pagecount and does not increase the
mapcount when mapping page into shadow page table entry,
so when comparing pagecount against mapcount, you have no
reliable result.)
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The number of entries is multiplied by the entry size, which can
overflow on 32-bit hosts. Bound the entry count instead.
Reported-by: David Wagner <daw@cs.berkeley.edu>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
It is possible that stale EPTP-tagged mappings are used, if a
vcpu migrates to a different pcpu.
Set KVM_REQ_TLB_FLUSH in vmx_vcpu_load, when switching pcpus, which
will invalidate both VPID and EPT mappings on the next vm-entry.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
commit 628eb9b8a8
KVM: s390: streamline memslot handling
introduced kvm_s390_vcpu_get_memsize. This broke guests >=4G, since this
function returned an int.
This patch changes the return value to a long.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When running nested we need to touch the l1 guests
tsc_offset. Otherwise changes will be lost or a wrong value
be read.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When svm_vcpu_load is called while the vcpu is running in
guest mode the tsc adjustment made there is lost on the next
emulated #vmexit. This causes the tsc running backwards in
the guest. This patch fixes the issue by also adjusting the
tsc_offset in the emulated hsave area so that it will not
get lost.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fixes the m32r SMP kernel after 2.6.27.
A part of the following patch breaks m32r SMP operation.
> m32r: convert to generic helpers for IPI function calls
> commit 7b7426c8a6
In the above patch, a CALL_FUNC_SINGLE_IPI was newly introduced,
but the its IPI vector number was wrong in the patch code.
The m32r SMP kernel hanged-up during boot operation, because
the CPU_BOOT_IPI was called instead of CALL_FUNC_SINGLE_IPI
(CPU_BOOT_IPI had no side effect at that time because the 2nd
core had already been started up),
as a result, csd_unlock() was not called, then a dead lock
occurred in csd_lock_wait() after the detection of Compact Flash
memory as IDE generic disk.
Signed-off-by: Toshihiro HANAWA <hanawa@ccs.tsukuba.ac.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
In case CONFIG_DISCONTIGMEM is set, the memory size of system was
always determined by CONFIG_MEMORY_SIZE and was not changeable.
This patch fixes set_memory() of arch/m32r/mm/discontig.c so that
we can specify memory size by the "mem=<size>" kernel parameter.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Define ioread* and iowrite* macros to fix the following build errors:
CC [M] drivers/uio/uio_smx.o
drivers/uio/uio_smx.c: In function 'smx_handler':
drivers/uio/uio_smx.c:31: error: implicit declaration of function 'ioread32'
drivers/uio/uio_smx.c:37: error: implicit declaration of function 'iowrite32'
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Fix pmd_bad check code of tme_handler (TLB Miss Exception handler).
The correct _KERNPG_TABLE value is not 0x263(=611) but 0x163.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Currently, on ARMv6 and ARMv7, if an application tries to execute
code (or garbage) on non-executable page it hangs. It caused by
incorrect prefetch abort handling. Now every prefetch abort
processes as a translation fault.
To fix this we have to analyze instruction fault status register
to figure out reason why we've got the abort and process it
accordingly.
To make IFSR different from DFSR we set bit 31 which is reserved in
both IFSR and DFSR.
This patch also tries to protect from future hangs on unexpected
exceptions. An application will be killed if unexpected exception
type was received.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instruction fault status register, IFSR, was introduced on ARMv6 to
provide status information about the last insturction fault. It
needed for proper prefetch abort handling.
Now we have three prefetch abort model:
* legacy - for CPUs before ARMv6. They doesn't provide neither
IFSR nor IFAR. We simulate IFSR with section translation fault
status for them to generalize code;
* ARMv6 - provides IFSR, but not IFAR;
* ARMv7 - provides both IFSR and IFAR.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1522ac3ec9
("Fix virtual to physical translation macro corner cases")
breaks the end of memory check in valid_phys_addr_range().
The modified expression results in the apparent /dev/mem size
being 2 bytes smaller than what it actually is.
This patch reworks the expression to correctly check the address,
while maintaining use of a valid address to __pa().
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: David Brown <davidb@quicinc.com>
The ATAG_CORE is allowed to be empty. Although this is handled
by parse_tag_core(), __vet_atags during startup rejects this tag
unless it contains data. Allow the initial tag to be either the
full size, or empty.
Signed-off-by: David Brown <davidb@quicinc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
EXPORT_* macros should follow immediately after the closing function
brace line.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current bound checks for copy_from_user in the MTRR driver are
not as obvious as they could be, and gcc agrees with that.
This patch simplifies the boundary checks to the point that gcc can
now prove to itself that the copy_from_user() is never going past
its bounds.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20090926205150.30797709@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make decoding of MCEs happen only on AMD hardware by registering a
non-default callback only on CPU families which support it.
While looking at the interaction of decode_mce() with the other MCE
code i also noticed a few other things and made the following
cleanups/fixes:
- Fixed the mce_decode() weak alias - a weak alias is really not
good here, it should be a proper callback. A weak alias will be
overriden if a piece of code is built into the kernel - not
good, obviously.
- The patch initializes the callback on AMD family 10h and 11h.
- Added the more correct fallback printk of:
No support for human readable MCE decoding on this CPU type.
Transcribe the message and run it through 'mcelog --ascii' to decode.
On CPUs that dont have a decoder.
- Made the surrounding code more readable.
Note that the callback allows us to have a default fallback -
without having to check the CPU versions during the printout
itself. When an EDAC module registers itself, it can install the
decode-print function.
(there's no unregister needed as this is core code.)
version -v2 by Borislav Petkov:
- add K8 to the set of supported CPUs
- always build in edac_mce_amd since we use an early_initcall now
- fix checkpatch warnings
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091001141432.GA11410@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add better support for omitting either the card detect or the write
protect GPIOs if the board does not support it. Add the fields
no_wprotect and no_detect to the platform data which when set indicate the
absence of the respective GPIOs.
Note, this also fixes a minor bug where it tries to free IRQ0 if there is
no detect gpio available.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a selection for the data transfer mode of the s3cmci driver, allowing
for either a configuration or rumtime selection of the use of the DMA or
PIO transfer code.
The PIO only mode is 476 bytes smaller than the driver with both methods
compiled in.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just like ip_fast_csum, the assembly snippet in csum_ipv6_magic needs a
memory clobber, as it is only passed the address of the buffer, not a
memory reference to the buffer itself.
This caused failures in Hurd's pfinetv4 when we tried to compile it with
gcc-4.3 (bogus checksums).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix some build failures when using gcc-4.x for MN10300.
Firstly, __get_user() fails to build because the pointer points to a const and
__gu_val ends up being read-only:
In file included from include/linux/mempolicy.h:62,
from init/main.c:50:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
make[1]: *** [init/main.o] Error 1
Secondly, gcc-4 doesn't allow casts of lvalues:
UPD include/linux/compile.h
arch/mn10300/kernel/rtc.c: In function 'calibrate_clock':
arch/mn10300/kernel/rtc.c:170: error: lvalue required as left operand of assignment
arch/mn10300/kernel/rtc.c:172: error: lvalue required as left operand of assignment
make[1]: *** [arch/mn10300/kernel/rtc.o] Error 1
These are seen with gcc 4.2.1.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 45d80eea87 ("m68k: convert to
asm-generic/hardirq.h") - it fails to compile due to an inclusion tangle:
In file included from include/linux/irq.h:12,
from include/asm-generic/hardirq.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq_mm.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq.h:4,
from include/linux/hardirq.h:10,
from /usr/src/devel/arch/m68k/include/asm/system_mm.h:69,
from /usr/src/devel/arch/m68k/include/asm/system.h:4,
from include/linux/list.h:7,
from include/linux/preempt.h:11,
from include/linux/spinlock.h:50,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:56,
from arch/m68k/kernel/asm-offsets.c:14:
include/linux/smp.h:17: error: field 'list' has incomplete type
Cc: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Christoph Hellwig <hch@lst.de>
[akpm@linux-foundation.org: /arch/sparc/include/asm/irq_32.h: move NR_IRQS definition]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 181f817eaa introduced some new code to entry-common.S
Sadly, this new code uses 'bx' instruction which is available only on
ARMv5 and higher CPUs. This causes following compilation errors when
building kernel for StrongARM (ARMv4):
arch/arm/kernel/entry-common.S: Assembler messages:
arch/arm/kernel/entry-common.S:129: Error: selected processor does not
support `bx ip'
arch/arm/kernel/entry-common.S:138: Error: selected processor does not
support `bx ip'
Fix these errors by using 'mov pc' instead of 'bx'.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The movement of the MMCI header file made bcmring break. It turns
out it was including asm/mmc.h without using it so fixing the
problem boils down to removing the offending include.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove duplicated #include('s) in arch/arm/mach-bcmring/core.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Leo Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The #ifdefs in the MMCI driver were erroneous and just masking
a bug in the U300 generic GPIO implementation. This removes the
ifdefs and fixes the U300 generic GPIO instead.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While 32-bit processes can't directly access R8...R15, they can
gain access to these registers by temporarily switching themselves
into 64-bit mode.
Therefore, registers not preserved anyway by called C functions
(i.e. R8...R11) must be cleared prior to returning to user mode.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <stable@kernel.org>
LKML-Reference: <4AC34D73020000780001744A@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove unused CONFIG FAST_CMPXCHG_LOCAL from Kconfig.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: linux-mm@kvack.org
LKML-Reference: <1253981501.4568.61.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit c953094 ("early_printk: Allow more than one early console")
introduced a regression in the parsing of the earlyprintk= kernel
arguments.
If you specify "earlyprintk=serial,ttyS0,115200" as a kernel
argument, the "serial,ttyS" should be parsed as a single argument
and not as "serial" and then "ttyS".
Also update the documentation to reflect you can specify the ttyS
directly without the "serial" argument.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
LKML-Reference: <4ABB7D5E.6000301@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conditionaly compile cmpxchg8b_emu.o and EXPORT_SYMBOL(cmpxchg8b_emu).
This reduces the kernel size a bit.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AC43E7E.1000600@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just like ip_fast_csum, the assembly snippet in csum_ipv6_magic needs a
memory clobber, as it is only passed the address of the buffer, not a
memory reference to the buffer itself.
This caused failures in Hurd's pfinetv4 when we tried to compile it with
gcc-4.3 (bogus checksums).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Try to avoid the 'alternates()' code when we can statically
determine that cmpxchg8b is fine. We already have that
CONFIG_x86_CMPXCHG64 (enabled by PAE support), and we could easily
also enable it for some of the CPU cases.
Note, this patch only adds CMPXCHG8B for the obvious Intel CPU's,
not for others. (There was something really messy about cmpxchg8b
and clone CPU's, so if you enable it on other CPUs later, do it
carefully.)
If we avoid that asm-alternative thing when we can assume the
instruction exists, we'll generate less support crud, and we'll
avoid the whole issue with that extra 'nop' for padding instruction
sizes etc.
LKML-Reference: <alpine.LFD.2.01.0909301743150.6996@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched_clock: Fix atomicity/continuity bug by using cmpxchg64()
x86: Provide an alternative() based cmpxchg64()
cmpxchg64() today generates, to quote Linus, "barf bag" code.
cmpxchg64() is about to get used in the scheduler to fix a bug there,
but it's a prerequisite that cmpxchg64() first be made non-sucking.
This patch turns cmpxchg64() into an efficient implementation that
uses the alternative() mechanism to just use the raw instruction on
all modern systems.
Note: the fallback is NOT smp safe, just like the current fallback
is not SMP safe. (Interested parties with i486 based SMP systems
are welcome to submit fix patches for that.)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
[ fixed asm constraint bug ]
Fixed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090930170754.0886ff2e@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/mips/include/asm/unaligned.h: linux/unaligned/generic.h is included more than once.
Entirely legitimate but just noise.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Produce an error if request_irq() fails.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: "Ithamar R. Adema" <ithamar.adema@team-embedded.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are 16 individual channels (NUM_DBDMA_CHANS) to save/restore plus the
global ddma block config (the +1). The last register in a channel can be
skipped since it's read-only (at offset 0x18).
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch 14275ccdb1e4b487cca745aba994699c426a31ee and
d5dedd4507 are conflicting and the
conflict was resolved badly in merge
92241940be501f798cb21db344bbb3d1ec3c4f1c resulting in the BCM1480 changes
of 14275ccdb1e4b487cca745aba994699c426a31ee getting lost. Sort out the
damage.
Reported and initial patch by Mark Mason <mmason@upwardaccess.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The definition of the irq_ipi structure has two initializations of the
flags field. This combines them.
[Ralf: The issue was originally introduced by commit
be4894196d79455f420dd7bb78be7dc73bec115c (linux-mips.org) rsp.
033890b084 (kernel.org). The original
intention of the code was to initialize .flags with both flags ored together.
The broken C code as actually implemented will be compiled by an equally
broken gcc to use only the last initialization, that is IRQF_PERCPU
which means this turned into an SMTC bug for 2.6.23 and newer.]
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: make allocation failures more verbose
percpu: make pcpu_setup_first_chunk() failures more verbose
percpu: make embedding first chunk allocator check vmalloc space size
sparc64: implement page mapping percpu first chunk allocator
percpu: make pcpu_build_alloc_info() clear static buffers
percpu: fix unit_map[] verification in pcpu_setup_first_chunk()
This reverts commit 22223c9b41, as
requested by Andi Kleen:
"Obviously kernels compiled with AMD support can still run on non AMD
systems, so messages like this can never be removed at compile time."
Requsted-by: Andi Kleen <andi@firstfloor.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Certain networking and USB workloads generate floods of these accesses,
so just disable it by default (thereby restoring the old behaviour). The
option remains configurable from userspace, and can still be used as a
debugging aid.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit f159ee7829 ("locking,
m68k/asm-offsets: Rename pt_regs offset defines") breaks the
m68knommu entry code that relies on these define names.
Fix the files to match the new define names.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix "Freeing initrd memory:" message m68knommu to show kilobytes as
claimed rather than number of pages.
Signed-off-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The hardware counter ->event_base state records and encoding of
the "struct perf_event_map" entry used for the event.
We use this to make sure that when we have more than 1 event,
both can be scheduled into the hardware at the same time.
As usual, structure of code is largely cribbed from powerpc.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement page mapping percpu first chunk allocator as a fallback to
the embedding allocator. The next patch will make the embedding
allocator check distances between units to determine whether it fits
within the vmalloc area so that this fallback can be used on such
cases.
sparc64 currently has relatively small vmalloc area which makes it
impossible to create any dynamic chunks on certain configurations
leading to percpu allocation failures. This and the next patch should
allow those configurations to keep working until proper solution is
found.
While at it, mark pcpu_cpu_distance() with __init.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Since we now use the embedding percpu allocator we have to make the
vmalloc area at least as large as the stretch can be between nodes.
Besides some minor asm adjustments, this turned out to be pretty
trivial.
Signed-off-by: David S. Miller <davem@davemloft.net>
do_cache_op() uses find_vma() to validate its arguments without holding
any locking. This means that the VMA could vanish beneath us. Fix
this by taking a read lock on mmap_sem.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
WARNING: vmlinux.o(.text+0x247c): Section mismatch in reference from the function cpu_idle() to the function .cpuexit.text:cpu_die()
The function cpu_idle() references a function in an exit section.
Often the function cpu_die() has valid usage outside the exit section
and the fix is to remove the __cpuexit annotation of cpu_die.
WARNING: vmlinux.o(.cpuexit.text+0x3c): Section mismatch in reference from the function cpu_die() to the function .cpuinit.text:secondary_start_kernel()
The function __cpuexit cpu_die() references
a function __cpuinit secondary_start_kernel().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __cpuinit annotation of
secondary_start_kernel() so it may be used outside an init section.
Sam says:
> The annotation of cpu_die() is wrong.
> To be annotated __cpuexit the function shall:
> - be used in exit context and only in exit context with HOTPLUG_CPU=n
> - be used outside exit context with HOTPLUG_CPU=y
So, this also means __cpu_disable(), __cpu_die() and twd_timer_stop() are
also wrong. However, removing __cpuexit from cpu_die() creates:
WARNING: vmlinux.o(.text+0x6834): Section mismatch in reference from the function cpu_die() to the function .cpuinit.text:secondary_start_kernel()
The function cpu_die() references
the function __cpuinit secondary_start_kernel().
This is often because cpu_die lacks a __cpuinit
annotation or the annotation of secondary_start_kernel is wrong.
so fix this using __ref.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
We suffer an unfortunate combination of "features" which makes highmem
support on platforms without hardware TLB maintainence broadcast difficult:
- we need kmap_high_get() support for DMA cache coherence
- this requires kmap_high() to take a spinlock with IRQs disabled
- kmap_high() occasionally calls flush_all_zero_pkmaps() to clear
out old mappings
- flush_all_zero_pkmaps() calls flush_tlb_kernel_range(), which
on s/w IPI'd systems eventually calls smp_call_function_many()
- smp_call_function_many() must not be called with IRQs disabled:
WARNING: at kernel/smp.c:380 smp_call_function_many+0xc4/0x240()
Modules linked in:
Backtrace:
[<c00306f0>] (dump_backtrace+0x0/0x108) from [<c0286e6c>] (dump_stack+0x18/0x1c)
r6:c007cd18 r5:c02ff228 r4:0000017c
[<c0286e54>] (dump_stack+0x0/0x1c) from [<c0053e08>] (warn_slowpath_common+0x50/0x80)
[<c0053db8>] (warn_slowpath_common+0x0/0x80) from [<c0053e50>] (warn_slowpath_null+0x18/0x1c)
r7:00000003 r6:00000001 r5:c1ff4000 r4:c035fa34
[<c0053e38>] (warn_slowpath_null+0x0/0x1c) from [<c007cd18>] (smp_call_function_many+0xc4/0x240)
[<c007cc54>] (smp_call_function_many+0x0/0x240) from [<c007cec0>] (smp_call_function+0x2c/0x38)
[<c007ce94>] (smp_call_function+0x0/0x38) from [<c005980c>] (on_each_cpu+0x1c/0x38)
[<c00597f0>] (on_each_cpu+0x0/0x38) from [<c0031788>] (flush_tlb_kernel_range+0x50/0x58)
r6:00000001 r5:00000800 r4:c05f3590
[<c0031738>] (flush_tlb_kernel_range+0x0/0x58) from [<c009c600>] (flush_all_zero_pkmaps+0xc0/0xe8)
[<c009c540>] (flush_all_zero_pkmaps+0x0/0xe8) from [<c009c6b4>] (kmap_high+0x8c/0x1e0)
[<c009c628>] (kmap_high+0x0/0x1e0) from [<c00364a8>] (kmap+0x44/0x5c)
[<c0036464>] (kmap+0x0/0x5c) from [<c0109dfc>] (cramfs_readpage+0x3c/0x194)
[<c0109dc0>] (cramfs_readpage+0x0/0x194) from [<c0090c14>] (__do_page_cache_readahead+0x1f0/0x290)
[<c0090a24>] (__do_page_cache_readahead+0x0/0x290) from [<c0090ce4>] (ra_submit+0x30/0x38)
[<c0090cb4>] (ra_submit+0x0/0x38) from [<c0089384>] (filemap_fault+0x3dc/0x438)
r4:c1819988
[<c0088fa8>] (filemap_fault+0x0/0x438) from [<c009d21c>] (__do_fault+0x58/0x43c)
[<c009d1c4>] (__do_fault+0x0/0x43c) from [<c009e8cc>] (handle_mm_fault+0x104/0x318)
[<c009e7c8>] (handle_mm_fault+0x0/0x318) from [<c0033c98>] (do_page_fault+0x188/0x1e4)
[<c0033b10>] (do_page_fault+0x0/0x1e4) from [<c0033ddc>] (do_translation_fault+0x7c/0x84)
[<c0033d60>] (do_translation_fault+0x0/0x84) from [<c002b474>] (do_DataAbort+0x40/0xa4)
r8:c1ff5e20 r7:c0340120 r6:00000805 r5:c1ff5e54 r4:c03400d0
[<c002b434>] (do_DataAbort+0x0/0xa4) from [<c002bcac>] (__dabt_svc+0x4c/0x60)
...
So we disable highmem support on these systems.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm365-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Removed unused CONFIG SA1100_H3XXX from Kconfig and defconfig
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We're not implementing this syscall (we're not NUMA) so we might as
well silence this warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
8e19608 missed updating SA11x0, and thus:
arch/arm/mach-sa1100/time.c:88: warning: initialization from incompatible pointer type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0xc9d4): Section mismatch in reference from the function pci_v3_scan_bus() to the function .devinit.text:pci_scan_bus_parented()
The function pci_v3_scan_bus() references
the function __devinit pci_scan_bus_parented().
This is often because pci_v3_scan_bus lacks a __devinit
annotation or the annotation of pci_scan_bus_parented is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
It's worked fine so far since reset is done for the first time.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is now no need for the magicpanelr2 and dreamcast platforms to set
their own I/O port bas values, given that the generic machvec code now
sets this to P2SEG for everyone.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's already code in do_page_fault() to conditionally enable
interrupts, so we don't need to unconditonally enable them before
calling it. This fixes a lockdep warning where we called
trace_hardirqs_off() but with irqs still enabled.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This bumps up the default I/O base to P2SEG, which allows legacy probing
to bail out gracefully rather than oopsing. Platforms that have a real
PIO offset still need to fix this up on their own, although most
platforms are content with P2SEG already.
The previous change to teach ioport_map() about >= P1SEG offsets in
combination with this patch allows both the already remapped and the
legacy address probing to pass through and succeed.
Fixes up an oops with i8042 on the sh7785lcr board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the case where certain drivers already do their own
remapping and subsequently attempt to use the PIO calls for I/O. In this
case there is no additional remapping that needs to be done, and the
address can be casted in to the cookie directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cribbed from powerpc code, as usual. :-)
Currently it is only used to validate that all counters
have the same user/kernel/hv attributes.
Signed-off-by: David S. Miller <davem@davemloft.net>
SHF_ALLOC is suitable for testing against the sh_flags field, not the
sh_type field.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
building kernel 2.6.32(pre), gives this compiler warning:
/linus-linux-2.6/mm/vmalloc.c: In function 'pcpu_get_vm_areas':
/linus-linux-2.6/mm/vmalloc.c:2104: warning: 'vmalloc_start' is used
uninitialized in this function
The reason is, that the code in mm/vmalloc defines a local variable called
vmalloc_start, which is already defined as global variable in parisc's code.
To avoid this kind of problems in future, I suggest to rename the parisc
variable
to parisc_vmalloc_start.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
fix the following 'make includecheck' warning:
arch/parisc/kernel/signal.c: linux/compat.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
task->ptrace flags belong to generic code, so instead thief some
TIF_ bits to use. Somewhat risky conversion of code to test TASK_FLAGS
instead of TASK_PTRACE in assembly, but it looks alright in the end.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Instead of fiddling with gr[20], restructure code to return whether
or not to -ENOSYS. (Also do a bit of fiddling to let them take
pt_regs directly instead of re-computing it.)
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This makes parisc call the standard tracehook_signal_handler hook
in <linux/tracehook.h> after setting up a signal handler.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This makes parisc use the standard tracehook_report_syscall_entry
and tracehook_report_syscall_exit hooks in <linux/tracehook.h>.
To do this, we need to access current->thread.regs, and to know
whether we're entering or exiting the syscall, so add this to
syscall_trace.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
.. duplicated by merging the same fix twice, for details see commit
0d9df2515d ("Merge
git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix hwpoison code related build failure on 32-bit NUMAQ
ia64's sim_defconfig uses CONFIG_ACPI=n
which now #define's acpi_disabled in <linux/acpi.h>
So we shouldn't re-define it here in <asm/acpi.h>
Signed-off-by: Len Brown <len.brown@intel.com>
This build failure triggers:
In file included from include/linux/suspend.h:8,
from arch/x86/kernel/asm-offsets_32.c:11,
from arch/x86/kernel/asm-offsets.c:2:
include/linux/mm.h:503:2: error: #error SECTIONS_WIDTH+NODES_WIDTH+ZONES_WIDTH > BITS_PER_LONG - NR_PAGEFLAGS
Because due to the hwpoison page flag we ran out of page
flags on 32-bit.
Dont turn on hwpoison on 32-bit NUMA (it's rare in any
case).
Also clean up the Kconfig dependencies in the generic MM
code by introducing ARCH_SUPPORTS_MEMORY_FAILURE.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't disable ARB_DISABLE when the familary ID is 0x0F.
http://bugzilla.kernel.org/show_bug.cgi?id=14211
This was a 2.6.31 regression, and so this patch
needs to be applied to 2.6.31.stable
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Hartley Sweeten