The module firmware information of 1000 series is missing from iwlagn.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.
.5000 series: L1-ASPM H/W bug work-around
configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
work-around for NIC get stuck after early PCIe power off
.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
setting digital SVR for 1000 card to 1.32V
.6000 series: configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
write CSR_GP_DRIVER_REG to indicate radio sku
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.
This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.
Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Green-field mode should be configured in the HT station table. This patch uses
both the per-station GF support flag as well as the current BSS HT operation
mode (non-GF stations present flag).
Added the "ht_greenfield_support" field to struct iwl_cfg to replace the
device-specific check in rs_use_green(). That check has been moved to
iwlcore_init_ht_hw_capab().
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices using OTP memory, EEPROM image can start from
any one of the OTP blocks. If shadow RAM is disabled, we need to
traverse link list to find the last valid block, then start the EEPROM
image reading.
If OTP is not full, the valid block is the block _before_ the last block
on the link list; the last block on the link list is the empty block
ready for next OTP refresh/update.
If OTP is full, then the last block is the valid block to be used for
configure the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename "fat" to "ht40"
The term "fat channel" is deprecated in favor of "HT40"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x00 2x2 NIC, two types of Power Amplifier are available.
In order for uCode to apply correct tx power,
driver needs to program the CSR_GP_DRIVER_REG register and
let uCode know the type of PA.
If driver do not program CSR_GP_DRIVER_REG register (default to 0),
then it is uCode's decision for tx power
2x2 Hybrid card: use both internal and external PA
2x2 IPA(Internal Power Amplifier) card: internal PA only
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "iwlwifi: Handle new firmware file with ucode build number
in header" introduced new ucode header parsing routines, but
neglected to initialize these routines for 1000. The system thus goes
into infinite loop trying to load ucode, failing every time with a null
pointer exception as it tries to parse the header.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If advance thermal throttling is used the driver need to pass both
"enter" and "exit" temperature to uCode.
Using different critical temperature threshold for legacy and advance
thermal throttling management based on the type of thermal throttling
method is used except 1000.
For 1000, it use advance thermal throttling critical temperature
threshold, but with legacy thermal management implementation until ucode
has the necessary implementations in place.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
firmware file now contains build number so API needs to be updated.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
device name was changed from 100 to 1000
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Huaxu Wan