On some NI 904x devices, using 3.3V signaling for extended periods of
time will physically damage the pads connected to the SDHC, eventually
causing complete failure of the controller. To work around this,
require that we avoid 3.3V signaling.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Arasan Controller is based on a FPGA platform and has integrated phy
with specific registers used during initialization and
management of different modes. The phy and the controller are integrated
and registers are very specific to Arasan.
Arasan being an IP provider, licenses these IPs to various companies for
integration of IP in custom SOCs. The custom SOCs define own register
map depending on how bits are tied inside the SOC for phy registers,
depending on SOC memory plan and hence will require own platform drivers.
If more details on phy registers are required, an interface document is
hosted at https://arasan.com/NF/eMMC5.1 PHY Programming in Linux.pdf.
Signed-off-by: Atul Garg <agarg@arasan.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaCXiaAAoJEP4mhCVzWIwp+c4P/3UptZJJScU4WFS1zXH8h/YK
mYQ4DOCZqQYihKV4ssbAAjmTkT3RdMkl+rq2s5+ZfVbsu57UqeHNaNXBQWirkXCo
xBDzZlZFz42g4apKq+ZfmewZTM2fjed8Z7SrDcxPkkyU90QKa/LFFleAyxyXxXr1
ubKHJtev/oWBRxvzvWPYNUI5ExraxGxp2iGvavoYHNcggAgOSBJoKESvF7er5MRK
Cx5cuKAESU2dJFQnebjndx3dFgQsZ18RTRXUom50oP3BXF2G3gIBMjxp9VfyuOGV
xedyE2ALQxr1bxyWWejMdhhiZ+eNZNtiEJKqJ37ArTeBDyDfO/SDVXlkqkAARlYW
rTzh9olfbuhFdCAo2gxAcCaQXnjgQzDDKnQJs++tQVziXGI9ezc44+A6fNh39nre
yc/MLIjN96vWRhhFuTeFuENN+n7D2xyy+keXZXrALYYOCPAlKtip6DOgVl3ltNvx
K1O7/STqdR4OHLK6vgdzi9ai3PmcmSBQwKCqqCH/7mcFm1xtBcxqdrEwORLQ3lCH
c/tl4lJqJR2BD8U9gipjik0ovWb5p2KKAYhjqEY2qMy14OXs2509Y8GcqQRzqcQc
FSAfUInooHfDEbUBVsLpTOjMvd6LAx34fTJ9QAanAZ1wdeV8C9DRz3kJh/L/mOmG
N7/jyJnMV1Izknmpc2MP
=3Gvx
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We keep PCI Ids in sdhci-pci.h and the O2-specific definitions belong in
sdhci-pci-o2micro.c. Move those definitions accordingly. Remove unused O2
definitions in sdhci-pci-core.c. The 3 o2micro external function
declarations might as well be in sdhci-pci.h as well, so move them there
and get rid of sdhci-pci-o2micro.h entirely.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add PCI ids and enhanced strobe support for Intel CNP. This is combined
with GLK due to the pending CMDQ support which they both share.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch applies customized PCI_DEVICE_ macros to specify the pci_ids
instead of open-coding them within the sdhci-pci driver.
By introducing device specific macros the pci_ids table becomes much
shorter and easier to comprehend than it would be possible using the
generic version of the PCI_DEVICE_ macros.
Signed-off-by: Matthias Kraemer <matthiasmartinsson@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The suspend / resume callbacks lack the flexibility to allow a device to
specify a different function entirely. Change them around so that device
functions are called directly and they in turn can call the default
implementations if needed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
It is confusing to have some parts of suspend / resume under conditional
compilation and some parts not. Use conditional compilation everywhere.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
SDHCI provides more flexibility than simply calling sdhci_add_host(). Make
that available by allowing devices to specify their own ->add_host()
function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Drivers can use the host operation directly, so remove this now unused
callback.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_pci_fixes structure, then sdhci_pci_probe_slot() will allocate extra
space for it, and sdhci_pci_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition. Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
cd_con_id is not used and always NULL.
Remove it to make code a bit more cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own sdhci_ops so that device-specific variations
can be implemented without adding quirks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 52ac7acf41 ("mmc: sdhci-pci: Convert to use managed functions
pcim_* and devm_*") converted ->probe() / ->remove() functions to use device
managed resource API. Here is a follow up to cover sdhci_pci_probe_slot() and
sdhci_pci_remove_slot().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Everywhere else in the code MRFLD abbreviation is used for Intel Merrifield. Do
the same for sdhci-pci.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e5 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add another PCI ID for an Intel eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the select_drive_strength callback to provide
drive strength selection for Intel SPT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for card detect for Bay Trail
and Braswell SD Card host controllers in PCI
mode.
This uses the gpio descriptor API which can find
gpio descriptors, for example, on an ACPI comapnion
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware is the same as used in Baytrail. Add these new PCI IDs to the
driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A host controller for a SD card may need a GPIO for card detect in order
to wake up from runtime suspend when a card is inserted. If that GPIO is
not configured, then the host controller will not wake up. Fix that for
the affected devices by not enabling runtime PM unless the GPIO is
successfully set up.
This affects BYT sd card host controller which had runtime PM enabled from
v3.11. For completeness, the MFD sd card host controller is flagged also.
The original patch before rebasing (see link below) was tested on v3.11.10
and v3.12.4 although the patch applied with some offsets and fuzz. The
original patch is here:
http://marc.info/?l=linux-mmc&m=138676702327057
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Chris Ball <chris@printf.net>
Break out definitions in sdhci-pci.c to sdhci-pci.h, for introducing
module files like sdhci-pci-xxx.c
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Chris Ball <chris@printf.net>
Kyle Roeschley