In some cases (e.g. when mac80211 calls iwl_mac_stop() for suspend or user
no longer wants device active), device has not been going into low power state
via __iwl_down(). apm_ops.reset() does not put device into low power state;
instead it resets the device, then puts it into a powered-up state ready to be
re-loaded with uCode and re-started. This has needlessly warmed up user's
laptops and drained batteries.
With current architecture in which mac80211 controls device up/down (including
resetting device after firmware errors), there is no need for apm_ops.reset()
any more; apm_ops.reset() is basically a combination of apm_ops.stop() and
apm_ops.init().
Instead, __iwl_down() now unconditionally places the device into a low-power
state via apm_ops.stop(). Device may be re-started via __iwl_up() calling
apm_ops.init() as soon as it may be needed (e.g. quickly for firmware errors),
but in the meantime, device will stop wasting energy.
Note that, even in this low power state, if driver re-enables interrupts,
the device retains the ability to sense the hardware RF-KILL switch, and
(except for 3945) interrupt the host when it changes.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update iwl3945_apm_init() to set up device registers in sequence most recently
recommended by factory.
Add resets for APMG interrupts and radio chip, formerly done only in
iwl3945_apm_reset(); moving them here assures that apm_init() will do
a complete job of preparing hardware not only after platform boot,
but also after apm_stop() has executed (due to rfkill, ifconfig down,
driver unload, etc.). This is in preparation to completely remove apm_reset().
Add some comments.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some airo card don't support power Management [1].
Don't abort suspend with those cards.
00:06.0 Network controller: AIRONET Wireless Communications PC4800 (rev 01)
Flags: medium devsel, IRQ 17
Memory at dffffe00 (32-bit, non-prefetchable) [size=128]
I/O ports at d000 [size=128]
I/O ports at cc00 [size=64]
Kernel driver in use: airo
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must check the bustype before using the host_pci pointer.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX is hung, the chip is reset. Ensure that
the chip is awake by using the PS wrappers.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return status of lbs_prepare_and_send_command and lbs_cmd_with_response
functions is not checked at some places. Those checks are added.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently several events are enabled from the firmware for which there
is no handling. This wakes up the host unnecessarily. Mask those
unneeded events.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use vmalloc to allocate memory for the firmware image, and use a smaller
linear buffer for the actual transfer of the firmware to the chipset.
This patch is an adaptation of a similar patch for wl1251 by Kalle Valo.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable multicast filtering. This way by default no multicast frames will
reach the host, and when needed, only required multicast frames can be
passed from the WLAN chipset to the host.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clear the probe-request template on the firmware after scan. Unless
cleared, the firmware can independently send probe requests to the AP
and interfere with the mac80211 logic.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the workqueue provided by the mac80211 stack instead of the system
default queue.
Modified to use new ieee_queue_work() as required by changes in the
stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a hack to disable all filters in the join command. This is based on
Kalle Valo's patch for wl1251.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Juuso as one of the module authors, since he's working heavily on this
module as well.
Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Corrections to the TX path - use correct number of maximum descriptors
(32 instead of 16) and correct checking and setting of excessive retries
on completion.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the usage of join's, including using actual beacon interval and
dtim from AP, and configuring a basic rate set from AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the rate policies to the firmware based on the rates given by
the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds implementation for checking for SPI busy words - i.e.
honoring a delay request from the WLAN chipset upon reading
registers/memory.
To optimized the average SPI ready by 32 bits, also configure the number
of busywords to one to disable the "fixed-busy-word" functionality.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ps-poll template aid bits 14 and 15 were not masked as required by
the standard. Mask them so that aid is sent in correct format.
This patch is a direct port of the respective patch for the wl1251
driver by Kalle Valo.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement delayed entry into ELP. This will promote the following:
- Less redundant sleep/wake cycles (better perf)
- Avoids known firmware issues with going to ELP too fast after an
operation
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the position to which TKIP header space is appended for TX
packets.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add security sequence number handling to the driver TX data path needed
by WPA.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the TX path implementation to allocate sufficient blocks in the
firmware for TX packets.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qual element in ieee80211_rx_status is not used anymore, so we don't need
to set it in the wl1271_rx_status() function. This saves a bit of time in
the RX path.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PA calibration for ar9271 ath9k_hw_9271_pa_cal() can run during
reset or initial calibration, update the PA calibration to account
for that and initialize PA calibration variables for both conditions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for the ar9271 hardware as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Test whether index is within bounds before reading the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'struct b43_wl' declaration is missing at 'leds.h'.
It should be declared to avoid getting some GCC warnings at 'b43_leds_unregister'.
Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"b43: Fix PPC crash in rfkill polling on unload" fixed the bug reported
in Bugzilla No. 14181; however, it introduced a new bug. Whenever the
radio switch was turned off, it was necessary to unload and reload
the driver for it to recognize the switch again.
This patch fixes both the original bug in #14181 and the bug introduced by
the previous patch. It must be stated, however, that if there is a BCM4306/3
with an rfkill switch (not yet proven), then the driver will need an
unload/reload cycle to turn the device back on.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the bonding device is no longer used in determining the device to
which to send packets, it can be dropped from the argument list of the various
xmit_hash_policy calls.
Signed-off-by: Jasper Spaans <spaans@fox-it.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7b6856a0 "can: provide library functions for skb allocation"
did not properly remove two lines of the SJA1000 driver resulting in
a 'skb_over_panic' when calling skb_put, as reported by Kurt.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the rxq# for LRO when processing the last fragment of a
frame. This helps in fast txq selection for routing workloads.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add include asm/cacheflush.h, because declaration of __flush_purge_region
moved to asm/cacheflush.h.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more careful about the state of pointers during tear-down.
The "pppoe_dev" field can only be looked at safely while holding socket locks.
This subsequently allows for the flush_lock to be killed.
We depend on the PPPOX_CONNECTED state to tell us that that those fields are
valid, so whoever clears that state (pppox_unbind_sock()) is responsible for
the dev_put() call.
We also have to ensure that we delete_item() on all sockets before they are
cleaned up.
The need for these changes has been exposed by scenarios wherein namespace
bindings of ethernet devices change while there are ongoing PPPoE sessions,
which resulted in oopses due to unusual socket connection termination paths,
exposing these issues.
Signed-off-by: Michal Ostrowski <mostrows@gmail.com>
Reviewed-by: Cyril Gorcunov <gorcunov@gmail.com>
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Tested-by: Denys Fedoryschenko <denys@visp.net.lb>
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch). This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired. The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.
The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed. However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers). This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset. If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak which occurs while changing the ring size
while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak that occurs when you resize the rings via
the ethtool -G option while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing ring sizes while the interface was down was causing a double
allocation of the receive and transmit rings. This issue is amplified when
there are multiple rings enabled. To prevent this we need to add an
additional check which will just update the ring counts when the interface
is not up and skip the allocation steps.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.
The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000B revision ID is 0x1A, not 0x1B as set in the curernt
dm9000.h header.
Fix bug reported by Paolo Zebelloni.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8110SC rev d chip on our board shows a regression which the 8110SB chip
did not have. When inbound traffic is overflowing the receive descriptor queue,
"holes" in the ring buffer may occur which lead to a hangup until the buffer
is filled again. The packets are than completely processed, but the ring
remains porous and no packets are processed until the next overflow. Setting
the interface down and up can fix the problem temporary from userspace.
For some reason we don't know, this behaviour is not occuring if the RxVlan
bit for hardware VLAN untagging is set. There is another "Work around for
AMD plateform" in the current code which checks the VLAN status
word in receive descriptors, but does never come to effect when hardware
VLAN support is enabled. We assume that this is a bug in the chip.
The following patch fixes the problem. Without the patch we could reproduce
the hang within minutes (given other devices also generating lots of
interrupts), without we couldn't reproduce within a few days of long term
testing.
This version contains minor style adjustments and is sent with mutt which
will hopefully not destroy the formatting again.
Signed-off-by: Bernhard Schmidt <bernhard.schmidt@saxnet.de>
Signed-off-by: Simon Wunderlich <simon.wunderlich@saxnet.de>
Acked-by: Francois Romieu <romieu@zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'XFP' driver is really a driver for the QT2022C2 and QT2025C PHYs,
covering both more and less than XFP. Rename its functions and
constants to reflect reality and to reduce namespace pollution when
sfc is a built-in driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only multi-speed PHY driver using this is 10Xpress, and it does
not support non-autoneg operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_fc_resolve() is specific to MDIO and is not used by any other
function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTD partition is named based on the netdev name, which is set to
'eth%d' before registration. Also, the MTD partition will currently
be left registered if netdev registration fails.
Fix both these problems by moving the MTD probe after netdev
registration. Hold the RTNL to serialise this with the netdev
notifier that calls efx_mtd_rename().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cleanup functions will never be called if the MMIO region could
not be mapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC and PHY probing are bound up together, as evidenced by the
initialisation of efx_nic::loopback_modes. Remove the current
arbitrary separation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the implementation a lot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes efx_pci_remove_main() more obviously the inverse of
efx_pci_probe_main(), and matches our out-of-tree driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the duplicated logic in efx_enqueue_skb() and
efx_tx_queue_insert() with an inline function, efx_max_tx_len().
Remove the failed attempt at abstracting hardware-specifics and put
all the magic numbers in efx_max_tx_len().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move size and mask definitions into efx.h; calculate page orders in falcon.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, use type suffixes of 'd', 'q' and 'o', consistent
with register type names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena is still based on the Falcon hardware architecture and will
share many of these definitions, so replace falcon_hwdefs.h with
regs.h.
The new definitions have been generated according to a naming
convention which incorporates the type and revision information.
Update the code accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there are now separate blocks of code to set the thresholds for
each NIC type, it is no longer useful to include them in the NIC type
description.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros are not extensible to more than two NIC types without
repetition of register definitions, and they are only used to deal
with a few fields in RX_CFG_REG and global events which moved between
Falcon rev A1 and B0.
Therefore:
- Move RX_CFG_REG initialisation into its own function which tests the
NIC revision just once
- Explicitly test the NIC revision when checking the RX_RECOVERY flag in
global events
- Merge definitions of RX_XOFF_MAC_EN flag, which did not move
- Remove the macro definitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena will require entirely different board code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point (ri_tasklet()), RTNL or dev_base_lock are not held,
we must use dev_get_by_index() instead of __dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes the following build failure:
CC drivers/net/au1000_eth.o
/drivers/net/au1000_eth.c: In function 'au1000_set_settings':
/drivers/net/au1000_eth.c:623: error: implicit declaration of function 'capable'
/drivers/net/au1000_eth.c:623: error: 'CAP_NET_ADMIN' undeclared (first use in this function)
/drivers/net/au1000_eth.c:623: error: (Each undeclared identifier is reported only once
/drivers/net/au1000_eth.c:623: error: for each function it appears in.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the reporting of myri10ge port type in ethtool,
and update for new boards.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect. Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 27fbc7d 'mdio: Expose pause frame advertising flags to ethtool'
and c634263 'sfc: 10Xpress: Initialise pause advertising flags'
added to our reported advertising flags.
efx_mdio_set_settings() requires that all advertising flags are
also present in the supported flags, so make sure that is true.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old code assumed board config version in the flash to be 1.
When this will get changed by tools, driver just refuses to
attach. This is unnecessary since driver does not have to
parse board config structure directly (maintained by firmware).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ks8851_set_rx_mode() the case handling IFF_MULTICAST was also setting
the RXCR1_AE bit by accident. This meant that all unicast frames where
being accepted by the device. Remove RXCR1_AE from this case.
Note, RXCR1_AE was also masking a problem with setting the MAC address
properly, so needs to be applied after fixing the MAC write order.
Fixes a bug reported by Doong, Ping of Micrel. This version of the
patch avoids setting RXCR1_ME for all cases.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address register was being written in the wrong order, so add
a new address macro to convert mac-address byte to register address and
a ks8851_wrreg8() function to write each byte without having to worry
about any difficult byte swapping.
Fixes a bug reported by Doong, Ping of Micrel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue a full soft reset at probe time.
This was reported by Doong Ping of Micrel, but no explanation of why this
is necessary or what bug it is fixing. Add it as it does not seem to hurt
the current driver and ensures that the device is in a known state when we
start setting it up.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the private functions alloc_can_skb() and
alloc_can_err_skb() of the at91_can driver public and adapts all
drivers to use these. While making the patch I realized, that
the skb's are *not* setup consistently. It's now done as shown
below:
skb->protocol = htons(ETH_P_CAN);
skb->pkt_type = PACKET_BROADCAST;
skb->ip_summed = CHECKSUM_UNNECESSARY;
*cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
memset(*cf, 0, sizeof(struct can_frame));
The frame is zeroed out to avoid uninitialized data to be passed to
user space. Some drivers or library code did not set "pkt_type" or
"ip_summed". Also, "__constant_htons()" should not be used for
runtime invocations, as pointed out by David Miller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2400m-sdio requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwmc3200wifi requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change RX large buffer size based on MTU. If pages are larger
than the MTU the page is divided up into multiple chunks and passed to
the hardware. When pages are smaller than MTU each RX buffer can
contain be comprised of up to 2 pages.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the problem of dropped packets due to lost of
interrupt requests. We should only clear what was pending at the
moment we read the irq source reg.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xmit handler doesn't need to wake the queue after stopping
it temporarily (some other drivers are doing the same).
Patch on net-next-2.6, multiple netperf sessions tested.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware hang detection and recovery (reset) need to
be disabled for diagnostic tools, which can run
some disruptive tests.
This adds a driver level control to turn off this
feature by diag tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use -EIO or -EINVAL as error codes, these can get passed up
to applications (tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for different windowing scheme for on chip
memory in future chip revisions. This is required by
diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions need different chip reset sequence
and firmware initialization.
Also clean up some never used debug code.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions of the chip have 128 bit memory
transactions. Require drivers to implement rmw
in case of sub-128 bit accesses by driver. This
is mostly used by diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new PCI ids to support next generation of BladeEngine device.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 was using dprintk() for debugging output. This was
defined in <linux/dst.h> and was the only thing that was
used from that header file. This caused compile errors
when CONFIG_BLOCK was not enabled due to bio* and BIO*
uses in the header file, so change this driver to use
dev_dbg() for debugging output.
include/linux/dst.h:520: error: dereferencing pointer to incomplete type
include/linux/dst.h:520: error: 'BIO_POOL_BITS' undeclared (first use in this function)
include/linux/dst.h:521: error: dereferencing pointer to incomplete type
include/linux/dst.h:522: error: dereferencing pointer to incomplete type
include/linux/dst.h:525: error: dereferencing pointer to incomplete type
make[4]: *** [drivers/net/vmxnet3/vmxnet3_drv.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is limited to the maximal BW allocation, so it should be displayed as
the link speed to notify the user.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is really no need to clear the MAC or the FW filtering rules - it was
added for completion, but caused race conditions with load/unload. Removing this
redundant code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCC commands are not protected with the RTNL lock, so a mutex should be added
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working with DCC, a function can be disabled or enabled (virtual link down
or up). Using the function state introduced some race conditions with the
load/unload flow.
Using a separate flag to indicate that the function is disabled.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of zero was used to disable the fairness mechanism. Though the code
(driver and FW) allowed changing the value at run time, it did not allow to do
that if the mechanism was disabled to begin with.
Fixed the FW to allow turning on and off the mechanism at run time. Fixed the
code to read the value from the chip at the right sequence.
Without this fix, if the initial value was set to zero, traffic could not run on
the interface.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before issuing any cmds to the FW, the driver must first wait
till the fW becomes ready. This is needed for PCI hot plug when
the driver can be probed while the card fw is being initialized.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 uses in_dev* interfaces so it should depend on INET.
Also fix so that the driver builds when CONFIG_PCI_MSI is disabled.
vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy'
drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bhavesh davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Randy Dunlap <randy.dunlap@oracle.com>
ks8851_mll uses mii interfaces so it needs to select MII.
ks8851_mll.c:(.text+0xf95ac): undefined reference to `generic_mii_ioctl'
ks8851_mll.c:(.text+0xf96a0): undefined reference to `mii_ethtool_gset'
ks8851_mll.c:(.text+0xf96fa): undefined reference to `mii_ethtool_sset'
ks8851_mll.c:(.text+0xf9754): undefined reference to `mii_link_ok'
ks8851_mll.c:(.text+0xf97ae): undefined reference to `mii_nway_restart'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus cannot be accessed at interrupt context, but on an FEC
error, the fec_mpc52xx driver reset function also tries to reset the
PHY. Since the error is detected at IRQ context, and the PHY functions
try to sleep, the kernel ends up panicking.
Resetting the PHY on an FEC error isn't even necessary. This patch
solves the problem by removing the PHY reset entirely.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some OF platform drivers are missing module device tables, so they won't
load automatically on boot. This patch fixes the issue by adding proper
MODULE_DEVICE_TABLE() macros to the drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lock_kernel/unlock_kernel() in cycle_kernel_lock() which is called
in tun_chr_open() is not serializing against anything and safe to
remove.
tun_chr_fasync() is serialized by get/put_tun() and fasync_helper()
has no dependency on BKL. The modification of tun->flags is racy with
and without the BKL so removing it does not make it worse.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.
With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the driver to accept a MAC address specified in platform_data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5675f221 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 337e067d overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 23d26497 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fd8235bb overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 59aa3cc4 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs entries to enable register and memory access
for diagnostic tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since register and onboard memory access has separate
window registers, they need not be kept under same lock.
Also, memory is always accessed from process context
(mostly for firmware init and diagnostic tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common variables crb_win, ocm_win for all revisions of chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access to on chip memory, this is used by
debug and diagnostic tools only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub 64-bit / unaligned access to oncard memory was only used
by old diagnostic tools, causes some intermittent issues when
memory controller agent is used. The new access method was
added by commit ea6828b8aa
("netxen: improve pci memory access"). Firmware init anyway
uses 8-byte strides.
This also fixes address/offset calculation for NX2031 context
memory (SIU). For NX3031, SIU uses same register offsets
as packet memory (MIU).
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit V_MAC_RX_PL_THRSH(4) was already set a few lines higher.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The negation makes it a bool before the comparison and hence it
will never evaluate to true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added support of private MAC address per port and provisioning
packet handler for iSCSI traffic only.
The above changes are isolated to the cxgb3 driver, independent of any scsi or iscsi driver changes.
Acked-by: Karen Xie <kxie@chelsio.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Runtime PM support to the sh_eth driver.
The clock to the ethernet hardware block will be
enabled as long as the network device is up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the sh_eth driver to allow passing the mac address
using the platform data structure. This to simplify board
setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the CAN controller driver to define the number of echo
skb's used for the local loopback (echo), as suggested by Kurt Van
Dijck, with the function:
struct net_device *alloc_candev(int sizeof_priv,
unsigned int echo_skb_max);
The CAN drivers have been adapted accordingly. For the ems_usb driver,
as suggested by Sebastian Haas, the number of echo skb's has been
increased to 10, which improves the transmission performance a lot.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bond_create_proc_entry is currently of type int.
Two versions of this function exist:
The one in the ifdef CONFIG_PROC_FS branch always return 0.
The one in the else branch (which is empty) return nothing.
When CONFIG_PROC_FS is undef, this cause the following warning:
drivers/net/bonding/bond_main.c: In function `bond_create_proc_entry':
drivers/net/bonding/bond_main.c:3393: warning: control reaches end of
non-void function
No caller of this function use the returned value.
So change the returned type from int to void and remove the
useless return 0; .
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c574_cs:
spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethoc.c: In function ‘ethoc_open’:
drivers/net/ethoc.c:667: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet NIC driver for VMware's vmxnet3
From: Shreyas Bhatewara <sbhatewara@vmware.com>
This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio module now handles reconfiguration of pause advertising
through ethtool, but not initialisation. Add the necessary
initialisation to tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mdio45_ethtool_gset_npage() and mdio45_ethtool_gset(), check MDIO
pause frame advertising flags and set the corresponding ethtool flags.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if pause autoneg is off we do not set either pause
advertising flag. If autonegotiation of speed and duplex settings is
enabled, there is no way for the link partner to distinguish this from
our refusing to use pause frames.
We should instead set the advertising flags according to the forced
mode so that the link partner can follow our lead. This is consistent
with the behaviour of other drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to various cleanups and refactorings this is now straightforward:
convert the gianfar driver to dev_pm_ops, plus add ->restore() callback
that will fully reinitialize MAC internal registers and BDs.
Note that I kept legacy suspend/resume callbacks so that this patch
doesn't depend on PowerPC changes (i.e. dev_pm_ops support for OF
platform drivers).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hibernation we want to just reinitialize BDs, no need to allocate
anything. So, factor out BDs initialization code from
gfar_alloc_skb_resourses().
Also, teach gfar_init_bds() to reuse already allocated RX SKBs, i.e.
just call gfar_init_rxbdp() if a SKB was already allocated and mapped.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to just reinitialize RX BDs after hibernation, no need to
map the skb->data again. So let's factor gfar_init_rxbdp() out of
gfar_new_rxbdp().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hibernation we want to call gfar_init_mac() without need to
free/allocate_skb_resources sequence, so save the DMA address into a
private struct, and move tbase/rbase initialization to gfar_init_mac().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new functions implemented: gfar_alloc_skb_resources() and
gfar_init_mac(). We'll use gfar_init_mac() for restoring after
hibernation.
The patch just moves the code around, there should be no functional
changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
startup_gfar() sets the wrap bit for the last rxbd just after
gfar_new_rxbdp() call, which is issued for all rxbds. And
gfar_new_rxbdp() has the following check already:
if (bdp == priv->rx_bd_base + priv->rx_ring_size - 1)
lstatus |= BD_LFLAG(RXBD_WRAP);
So we don't need to set the bit again.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dma_free_coherent() from stop_gfar() and gfar_start() calls,
place it into free_skb_resources(). That makes SKB resources management
more understandable, plus free_skb_resources() will be used as a cleanup
routine for gfar_alloc_skb_resources() that will be implemented soon.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to split the startup_gfar() into 3 separate functions,
so let's cleanup the code a little bit so that cosmetic changes
won't distract attention from logical ones.
- Remove needless casts (e.g. (struct sk_buff **)kmalloc());
- Turn 'unsigned long vaddr;' into 'void *vaddr', to avoid casting;
- Add new 'struct device *dev' variable as a shorthand for
'&priv->ofdev->dev' that is used all over the place, also rename
'struct net_device *dev' to 'struct net_device *ndev';
- Turn printk(KERN_ERR ...) to pr_err(...), which is shorter;
- Don't return bogus -1 (i.e. -EPERM) when request_irq() fails;
- Turn '&priv->regs->' to just '®s->'.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cnic.c: In function 'cnic_init_storm_conn_bufs':
drivers/net/cnic.c:1757: error: implicit declaration of function 'csum_ipv6_magic'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool set settings to pasemi_mac_ethtool.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the way it interacts with the networking
stack and other parts of mac80211, ieee80211_rx()
must be called with disabled softirqs.
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/39440/focus=40266
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add iSCSI support for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hardware and software structures for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor ring init. code for subsequent 10G patches. Also add rtnl_lock()
in cnic_uio_open() to prevent race condition with netdev events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the main CNIC registration, callback, MAC addr. setup functions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to initialize hardware blocks used for iSCSI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For iSCSI MAC address setup in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the SPQ (slow-path queue) operations will be used
by the cnic code in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ring->sbq_buf_len now holds the length of the mapped portion of the
buffer rather than the overall length.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has nothing to do, but this marker prevents the event from
showing up 'not handled'.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove explicit setting of error reporting bits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them. So link them in first.
Based upon a report by Felix Radensky.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is somewhat non-sensical to allow selecting wireless
drivers without showing wireless core code options, and
since the wext refactoring this has made it possible to
generate configurations that will not build. Avoid this
and make wireless drivers select the wireless options.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This came in through the patch titled:
libertas: first stab at cfg80211 support
I only noticed it because it breaks compat-wireless :)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: sujith.manoharan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the recently added backplane device IDs that support KR
to fail over to KX during link setup. This is accomplished by the new MAC
link setup function ixgbe_setup_mac_link_smartspeed(). Comments were also
updated to better document the reason for the delays chosen for KX, KX4, BX,
BX4 and KR connections.
Signed-off-by: Don Skidmore <don.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add the device ID for the 82599-based Ethernet
Express Module X520-P2 SFI card.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the EMAC V4 implementations support 16K Tx FIFOs. This
patch adds support for this functionality and fixes typos in the
Tx FIFO size error messages.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Victor Gallardo <vgallardo@appliedmicro.com>
Acked-by: Loc Ho <lho@appliedmicro.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was accidentally omitted from one of the previous patches for firmware event
handling. The handler needs to the enable firmware irq mask when it's done
processing or it may not get any more events interrupts.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call set_multi API after reset recovery. This was exposed by tripping
tx_timeout.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wait for NIC fifo and MGMNT fifo to empty before applying reset.
Otherwise broken frames can be processed by management processor and
cause it to hang.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addresses were being added to the filter properly, but were not
being enabled. This adds enable bit to filter write.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcast/multicast should always be routed to the default (zeroeth) rx
ring. Broadcast frames are already routed correctly. This fixes
routing for multicast frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently frames are routed based on their type and MAC address. This
patch adds the port number on which the frame arrived to the routing.
This prevents problems in the case where both interfaces have the same MAC address in
a routing configuration.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix RX queue table size and change from random to default hash values.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI HECC (High End CAN Controller) module is found on many TI devices. It
has 32 hardware mailboxes with full implementation of CAN protocol 2.0B
with bus speeds up to 1Mbps. Specifications of the module are available
on TI web <http://www.ti.com>
Signed-off-by: Anant Gole <anantgole@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private myri10ge_priv structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable old_active is first set to bond->curr_active_slave.
Then, it is unconditionally set to new_active, without being used in between.
The first assignment, having no side effect, is useless.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing module parameters, bond_check_params() erroneously use
'xor_mode' as the name of a module parameter in an error message.
The right name for this parameter is 'xmit_hash_policy'.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As kindly pointed out by Andrey Yurovsky, CONFIG_LIBERTAS already
selects FW_LOADER.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_is_cmd_allowed() check is added in __lbs_cmd_async() and
lbs_prepare_and_send_command(). The check is removed from other places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And move it to hw code on mac.c where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core driver needs to be stopped and then as a last step the
hardware needs to be stopped and its structure free'd. We do this
by moving the core driver cleanup to a new helper ath_clean_core()
and have ath_cleanup() call it. Only as a last step does
ath_cleanup() now free the hw.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used in several places, ensure we do it right in all
callers by using a helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs uses the hardware for several debugfs files as such the
hardware must be initialized and available prior to its usage. The
same applies to when we free the hw structs -- free debufs file
entries prior to free'ing the hardware.
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What this means is we can enable now debug prints without
requiring CONFIG_ATH9K_DEBUG.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has long provided us the association ID. This isn't useful except
for Power-Save polling which now gets enabled. We can now poll for our
pending frames on the AP during power save.
You can review the details of Power-Save on the wireless wiki:
http://wireless.kernel.org/en/developers/Documentation/ieee80211/power-savings
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression introduced by patch titled:
"atheros: define shared bssidmask setting"
The register for the BSSID was exchanged for the bssid mask register.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have access to common->curbssid and common->curaid so just
use those. Note that common->curaid is always 0 so this keeps
our current behaviour of always using 0 for now. Once we fix
storing the association ID passed by mac80211 this will
require no changes here.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The trick was to add four bytes whenever this was used. There
are two places where this was missed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo on the second bssid mask register.
This was caused by the patch titled:
"ath5k: use common curbssid, bssidmask and macaddr"
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also sorts all "source" lines in the wireless/Kconfig.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the suspend and resume callbacks of ath5k by converting the
driver to struct dev_pm_ops and allowing the PCI PM core to do the
PCI-specific suspend/resume handling.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set firmware and hardware version in wiphy so that user space can access
it.
(Modification from original in favor of cfg80211 ethtool support. -- JWL)
Cc: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both 1000 & 6000 series NICs contain on-chip OTP memory that
replaces the off-chip EEPROM memory. The nature of OTP means
there is a limited number of times a particular board can go through the
factory flow and be (re)calibrated. As a consequence there will be some boards
that contain EEPROM memory because OTP blocks were full.
In the signature validation routine, iwlwifi needs to make sure
"select bit" and "EEPROM/OTP signature" agree on the type of
NVM to be used to configure the system.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace iwl_poll_direct_bit with iwl_poll_bit when accessing CSR registers.
There is no need to power up the mac to access CSR registers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.
Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.
At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.
The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple MPDUs can be aggregated, transmitted, and finally acknowledged
together using a single BA frame. Block ACK (BA) contains
bitmap size of 64*16 bits so the maximum frame count is 64.
The default value of aggregation frame count suggested by uCode is 31 to
achieve best performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should clear the translate table area after receiving "Alive"
response from uCode. This patch corrects a mistake when doing this.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Guo Chaohong <chaohong.guo@linux.intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support different type of 1000 series NICs we release to
customers before the production release, iwlwifi driver need to support
all the NICs has EEPROM version greater than 0x15c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode detects critical temperature it should send "card state
notification" interrupt to driver and then shut itself down to prevent
overheating. There is a race condition where uCode shuts down before it
can deliver the interrupt to driver.
Additional method provided here for driver to enter CT_KILL state based
on temperature reading.
How it works:
Method 1:
If driver receive "card state notification" interrupt from uCode; it
enters "CT_KILL" state immediately
Method 2:
If the last temperature report by Card reach Critical temperature,
driver will send "statistic notification" request to uCode to verify the
temperature reading, if driver can not get reply from uCode within
300ms, driver will enter CT_KILL state automatically.
Method 3:
If the last temperature report by Card did not reach Critical
temperature, but uCode already shut down due to critical temperature.
All the host commands send to uCode will not get process by uCode;
when command queue reach the limit, driver will check the last reported
temperature reading, if it is within pre-defined margin, enter "CT_KILL"
state immediately. In this case, when uCode ready to exit from "CT_KILL" state,
driver need to restart the adapter in order to reset all the queues and
resume normal operation.
One additional issue being address here, when system is in CT_KILL
state, both tx and rx already stopped, but driver still can send host
command to uCode, it will flood the command queue since card was not
responding; adding STATUS_CT_KILL flag to reject enqueue host commands
to uCode if it is in CT_KILL state, when uCode is ready to come out of
CT_KILL, driver will clear the STATUS_CT_KILL bit and allow enqueue the host
commands to uCode to recover from CT_KILL state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file was accidentally added in commit ef2f8d4577 ("wl1251: add
wl1251 prefix to all 1251 files"). This happened when I rebased the
patches from a private tree.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add timer based auto deep sleep feature in libertas driver which can be
configured using iwconfig command. This is tested on SD8688, SD8686 cards
with firmware versions 10.38.1.p25, 9.70.4.p0 respectively on 32-bit and 64-bit
platforms. Tests have been done for USB/CS cards to make sure that the patch
won't break USB/CS code. We didn't test the if_spi driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code should never use private driver data, but
sometimes we need a backpointer so just stuff it on
the common ath struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows for hw support to be enabled for ar9271.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.
The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI and debug code will not be shared between ath9k and
ath9k_htc, so make that code use the common read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commenting unused functions lpphy_restore_dig_flt_state and
lpphy_disable_rx_gain_override, may be we need these functions in future.
This also fixed following compilation warnings :
CC [M] drivers/net/wireless/b43/phy_lp.o
drivers/net/wireless/b43/phy_lp.c:383: warning: ‘lpphy_restore_dig_flt_state’ defined but not used
drivers/net/wireless/b43/phy_lp.c:891: warning: ‘lpphy_disable_rx_gain_override’ defined but not used
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since Johannes' "iwlwifi: improve scan support" iwlwifi
no longer needs any of lib80211's functions or definitions.
This patch updates iwlwifi's Kconfig _selections_ and
removes all left lib80211.h inclusions from the source files.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Get power table offset from the EEPROM instead of using
a hardcoded value of -5 if the EEPROM rev is >= 21.
* Add support in the 4k eeprom code for tx power offset
in case we have a 4k AR9280 implementation.
* Fix tx power accuracy at high powers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has to be done if the EEPROM supports FCC Midband
capability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce PLL Settle time and eliminate redundant PLL calls. Also reduce
the LoadNF timeout from 10 msec to 250usec as the 10 msec timeout was
hit with AR9285 in some cases.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing a local variable is unnecessary.
Get rid of it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move 0xa274 and 0xa27c to the top of tx_gain table.
* Update initvals to fix random failure of noise floor calibration.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR5416 chipsets, clearing RTC_RESET_EN when setting
the chip to SLEEP mode results in high power consumption.
This patch fixes this issue by not clearing it for AR5416.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is between 2412 and 2472 MHz and if the channel is
changing to 2484 MHz, then the registers 0xa1f4, 0xa1f8 and 0xa1fc need to be
programmed to the "japan_2484" values. Conversely, if the current channel
is 2484 MHz and if the channel is changing to one between 2412 and 2472 MHz, then
the three registers need to be programmed to the "normal" values.
This is needed for compliance with Japanese regulatory requirements.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Prevent divide-by-zero errors in IQ Calibration.
* Do not run temperature compensation if initPDADC or currPDADC is zero.
* Also, introduce a separate function for handling OLC for AR9287.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar9170_op_get_tsf: handle a carry from TSF_L into TSF_H
by reading TSF_H twice.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add heavy clip handling for 2.4GHz only (similar to the vendor driver).
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some coding style issues and moves MAX_RATE_POWER into hw.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module firmware information of 1000 series is missing from iwlagn.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When instructing the microcode to use just a single
chain when we have power saving enabled, we should
also tell the AP that we are doing SM powersave.
However, using a single chain doesn't actually have
any power saving advantage while idle -- measurements
show that the power consumption is no different when
using one vs. two or three chains.
Therefore, always instruct the microcode to use all
chains.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never have four chains, but let's fix the typo
while we noticed it. You count 0, 1, 2, 3, not
0, 1, 2, 4 :)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Today's implementation allow LED to blink based on the traffic
condition. We introduce an additional LED mode that reflects the RF
state.
The supported LED modes after this are:
IWL_LED_BLINK (current/default) - blink rate based on current Tx/Rx
traffic
IWL_LED_RF_STATE (new) -
LED OFF: No power/RF disabled, the LED is emitting no light
LED ON: Powered/RF enabled, the LED is emitting light
in a stable non-flashing state.
In order to provide the flexibility to support different LED
behavior per user/system preference we add "led_mode" iwlcore module
parameter.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 60x0 series based on HW SKU. Adding new SKU
for "ABG" and "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.
The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current rate scale algorithm fluctuates between different MIMO modes fairly
rapidly, causing widely varying performance. These fluctuations occur because in
the rate_scale tables for expected throughput the values are not very different
for different modes.
However, when aggregation is turned on and MAC overhead is reduced, the
expected throughput for different MIMO modes grows and different modes have
vastly different performance. Add expected throughput tables for this case.
We also need to keep track of aggregation status per-station, so we add the
"is_agg" field to struct lq_sta.
Also includes cleanup of comments and variable names in/around the affected
code.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OR-in AMPDU flags rather than assigning them. This lets the TX status for
aggregated packets be processed by rs_tx_status.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cut down on redundant code, reorganize structure, and add/improve comments.
Should contain no functional changes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow user to change protection mechanism for HT between RTS/CTS and
CTS-to-self through sysfs:
Show current protection mechanism for HT
cat /sys/class/net/wlan0/device/rts_ht_protection
Change protection mechanism for HT (only allowed while not-associated)
CTS-to-self:
echo 0 > /sys/class/net/wlan0/device/rts_ht_protection
RTS/CTS:
echo 1 > /sys/class/net/wlan0/device/rts_ht_protection
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).
Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.
Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).
All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.
For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show version number along with dumping NVM data, the version information
being removed from sysfs, add it back to debugfs to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill