The call to of_get_mac_address() can return -EPROBE_DEFER, for instance
when the MAC address is read from a NVMEM driver that did not probe yet.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that
BE[3:0] signals are active high. This contradicts the measurements
of the behavior of the actual chip, where these signals behave as
active low. For example, to read the CIDER register, the bus must
expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet data written to and read from Micrel KSZ8851-16MLLI must be
byte-swapped in 16-bit mode, add this byte-swapping.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown,
however the speculation is that this was some sort of attempt to support
the 8-bit bus mode.
As per the KS8851-16MLL documentation, all two registers accessed via the
8-bit accessors are internally 16-bit registers, so reading them using
16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read
outright, as it is already a concatenation of two 8-bit reads of that
register. The KS_RXQCR accesses are 8-bit only, however writing the top
8 bits of the register is OK as well, since the driver caches the entire
16-bit register value anyway.
Finally, the driver is not used by any hardware in the kernel right now.
The only hardware available to me is one with 16-bit bus, so I have no
way to test the 8-bit bus mode, however it is unlikely this ever really
worked anyway. If the 8-bit bus mode is ever required, it can be easily
added by adjusting the 16-bit accessors to do 2 consecutive accesses,
which is how this should have been done from the beginning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure that the default VID is untagged otherwise the switch
will be sending tagged frames and the results can be problematic. This
is especially true with b53 switches that use VID 0 as their default
VLAN since VID 0 has a special meaning.
Fixes: fea8335317 ("net: dsa: b53: Fix default VLAN ID")
Fixes: 061f6a505a ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
synchronize_net() is a wrapper around synchronize_rcu(), so there's no
point in having synchronize_net and synchronize_rcu back to back,
despite the documentation comment suggesting maybe it's somewhat useful,
"Wait for packets currently being received to be done." This commit
removes the extra call.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out there's an easy way to get packets queued up while still
having an MTU of zero, and that's via persistent keep alive. This commit
makes sure that in whatever condition, we don't wind up dividing by
zero. Note that an MTU of zero for a wireguard interface is something
quasi-valid, so I don't think the correct fix is to limit it via
min_mtu. This can be reproduced easily with:
ip link add wg0 type wireguard
ip link add wg1 type wireguard
ip link set wg0 up mtu 0
ip link set wg1 up
wg set wg0 private-key <(wg genkey)
wg set wg1 listen-port 1 private-key <(wg genkey) peer $(wg show wg0 public-key)
wg set wg0 peer $(wg show wg1 public-key) persistent-keepalive 1 endpoint 127.0.0.1:1
However, while min_mtu=0 seems fine, it makes sense to restrict the
max_mtu. This commit also restricts the maximum MTU to the greatest
number for which rounding up to the padding multiple won't overflow a
signed integer. Packets this large were always rejected anyway
eventually, due to checks deeper in, but it seems more sound not to even
let the administrator configure something that won't work anyway.
We use this opportunity to clean up this function a bit so that it's
clear which paths we're expecting.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a small optimization that prevents more expensive comparisons
from happening when they are no longer necessary, by clearing the
last_under_load variable whenever we wind up in a state where we were
under load but we no longer are.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Suggested-by: Matt Dunwoodie <ncon@noconroy.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mii management register in iproc mdio block
does not have a retention register so it is lost on suspend.
Save and restore value of register while resuming from suspend.
Fixes: bb1a619735 ("net: phy: Initialize mdio clock at probe function")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix static checker warning:
drivers/net/ethernet/aquantia/atlantic/aq_filters.c:166 aq_check_approve_fvlan()
error: passing untrusted data to 'test_bit()'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7975d2aff5af: ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
during hibernation freeze, aq_nic_stop could be invoked
on a stopped device. That may cause panic on access to
not yet allocated vector/ring structures.
Add a check to stop device if it is not yet stopped.
Similiarly after freeze in hibernation thaw, aq_nic_start
could be invoked on a not initialized net device.
Result will be the same.
Add a check to start device if it is initialized.
In our case, this is the same as started.
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code inspection found that in case of mapping error we do return current
'ret' value. But beside error, it is used to count number of descriptors
allocated for the packet. In that case map_skb function could return '1'.
Changing it to return zero (number of mapped descriptors for skb)
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->len is used to calculate statistics after xmit invocation.
Under a stress load it may happen that skb will be xmited,
rx interrupt will come and skb will be freed, all before xmit function
is even returned.
Eventually, skb->len will access unallocated area.
Moving stats calculation into tx_clean routine.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Reported-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checks to not enable multiple loopback modes simultaneously,
It was also discovered that for dma loopback to function correctly
promisc mode should be enabled on device.
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clock adjustment data should be passed to FW as well, otherwise in some
cases a drift was observed when using GPIO features.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Artificial HW reliability tests revealed a possible hangup in
the driver. Normally, when device disappears from bus, all
register reads returns 0xFFFFFFFF.
At remote procedure invocation towards FW there is a logic
where result is compared with -1 in a loop.
That caused an infinite loop if hardware due to some issues
disappears from bus.
Add extra result checks to prevent this.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yet another checksum offload compatibility issue was found.
The known issue is that AQC HW marks tcp packets with 0xFFFF checksum
as invalid (1). This is workarounded in driver, passing all the suspicious
packets up to the stack for further csum validation.
Another HW problem (2) is that it hides invalid csum of LRO aggregated
packets inside of the individual descriptors. That was workarounded
by forced scan of all LRO descriptors for checksum errors.
However the scan logic was joint for both LRO and multi-descriptor
packets (jumbos). And this causes the issue.
We have to drop LRO packets with the detected bad checksum
because of (2), but we have to pass jumbo packets to stack because of (1).
When using windows tcp partner with jumbo frames but with LSO disabled
driver discards such frames as bad checksummed. But only LRO frames
should be dropped, not jumbos.
On such a configurations tcp stream have a chance of drops and stucks.
(1) 76f254d4af ("net: aquantia: tcp checksum 0xffff being handled incorrectly")
(2) d08b9a0a3e ("net: aquantia: do not pass lro session with invalid tcp checksum")
Fixes: d08b9a0a3e ("net: aquantia: do not pass lro session with invalid tcp checksum")
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of autosuspend, at91ether_start is called with clocks disabled.
Ensure that pm_runtime doesn't suspend the interface as soon as it is
opened as there is no pm_runtime support is the other relevant parts of the
platform support for at91rm9200.
Fixes: d54f89af6c ("net: macb: Add pm runtime support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 address defined in struct in6_addr is specified as
big endian, but there is no specified endian in struct
hclge_fd_rule_tuples, so it will cause a problem if directly
use memcpy() to copy ipv6 address between these two structures
since this field in struct hclge_fd_rule_tuples is little endian.
This patch fixes this problem by using be32_to_cpu() to convert
endian of IPv6 address of struct in6_addr before copying.
Fixes: d93ed94fbe ("net: hns3: add aRFS support for PF")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling 4 TC after setting the bandwidth of VF, the bandwidth
of VF will resume to default value, because of the qset resources
changed in this case.
This patch fixes it by using a fixed VF's qset resources according to
HNAE3_MAX_TC macro.
Fixes: ee9e44248f ("net: hns3: add support for configuring bandwidth of VF on the host")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current process, the management table is missing after the
IMP reset. This patch adds the management table to the reset process.
Fixes: f5aac71c03 ("net: hns3: add manager table initialization for hardware")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because wireguard is calling icmp from network device context, it should
use the ndo helper so that the rate limiting applies correctly. This
commit adds a small test to the wireguard test suite to ensure that the
new functions continue doing the right thing in the context of
wireguard. It does this by setting up a condition that will definately
evoke an icmp error message from the driver, but along a nat'd path.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because sunvnet is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly. While we're
at it, doing the additional route lookup before calling icmp_ndo_send is
superfluous, since this is the job of the icmp code in the first place.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because gtp is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the correct netif_msg_[tx,rx]_error() function to determine whether to
print the MDD event type.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove local variable num_q_vectors and use vsi->num_q_vectors instead
2. Remove local variable pf and pass vsi->back to ice_pf_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formatting strings in print function calls (like dev_info, dev_err, etc.)
can exceed 80 columns without making checkpatch unhappy. So remove
newlines where applicable and make print statements more compact.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 1f45ebe0d8 ("ice: add extra check for null Rx descriptor") moved
the call to ice_construct_skb() under a null check as Coverity reported a
possible use of null skb. However, the original call was not deleted, do so
now.
Fixes: 1f45ebe0d8 ("ice: add extra check for null Rx descriptor")
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset the Unit Load Status bits in the GLNVM_ULD register to check
for completion should be 0x7FF before continuing. Update the mask to check
(minus the three reserved bits that are always set).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool. Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe. This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies link message logging to include "Full Duplex" and
"Negotiated" for FEC, so as to distinguish it from "Requested" FEC.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dev_onetime_setup contains driver workarounds needed for
firmware limitations. These issues have now been resolved in newer
NVMs so remove the function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display all of the supported and advertised link modes based on the PHY
capability with media.
Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured. This is causing
a problem when shutting down lldpad. The cleanup
is trying to delete TLV apps that are not defined
in the kernel.
Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.
For FW flow, the willing setting was being
forced to OFF and left that way. Unwilling
in DCB FW mode is not a supported model.
Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.
The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).
Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.
Also adding a reapplication of the current DCB
config after a link event. Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090
After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.
After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
enic_poll_msix_wq->
vnic_cq_service->
enic_wq_service->
netif_wake_subqueue(enic->netdev, q_number)->
test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.
Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
comp_ctx can be NULL in a very rare case when an admin command is executed
during the execution of ena_remove().
The bug scenario is as follows:
* ena_destroy_device() sets the comp_ctx to be NULL
* An admin command is executed before executing unregister_netdev(),
this can still happen because our device can still receive callbacks
from the netdev infrastructure such as ethtool commands.
* When attempting to access the comp_ctx, the bug occurs since it's set
to NULL
Fix:
Added a check that comp_ctx is not NULL
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up till kernel 4.11 there was no enum defined for crc32 hash in ethtool,
thus the xor enum was used for supporting crc32.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing
the key or indirection table using ethtool while keeping the same hash
function.
Also add a function for retrieving the current hash function from
the ena-com layer.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ena_com_ind_tbl_convert_from_device() has an overflow
bug as explained below. Either way, this function is not needed at
all since we don't retrieve the indirection table from the device
at any point which means that this conversion is not needed.
The bug:
The for loop iterates over all io_sq_queues, when passing the actual
number of used queues the io_sq_queues[i].idx equals 0 since they are
uninitialized which results in the following code to be executed till
the end of the loop:
dev_idx_to_host_tbl[0] = i;
This results dev_idx_to_host_tbl[0] in being equal to
ENA_TOTAL_NUM_QUEUES - 1.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indirection table has the indices of the Rx queues. When we store it
during set indirection operation, we convert the indices to our internal
representation of the indices.
Our internal representation of the indices is: even indices for Tx and
uneven indices for Rx, where every Tx/Rx pair are in a consecutive order
starting from 0. For example if the driver has 3 queues (3 for Tx and 3
for Rx) then the indices are as follows:
0 1 2 3 4 5
Tx Rx Tx Rx Tx Rx
The BUG:
The issue is that when we satisfy a get request for the indirection
table, we don't convert the indices back to the original representation.
The FIX:
Simply apply the inverse function for the indices of the indirection
table after we set it.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device receives, stores and retrieves the hash function value as bits
and not as their enum value.
The bug:
* In ena_com_set_hash_function() we set
cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func.
(1 << rss->hash_func)
* In ena_com_get_hash_function() we retrieve the hash function and store
it's bit value in rss->hash_func. (Now the bit value of rss->hash_func
is stored in rss->hash_func instead of it's enum value)
The fix:
This commit fixes the issue by converting the retrieved hash function
values from the device to the matching enum value of the set bit using
ffs(). ffs() finds the first set bit's index in a word. Since the function
returns 1 for the LSB's index, we need to subtract 1 from the returned
value (note that BIT(0) is 1).
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On old hardware, getting / setting the hash function is not supported while
gettting / setting the indirection table is.
This commit enables us to still show the indirection table on older
hardwares by setting the hash function and key to NULL.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we allocate the key whether the device supports setting the
key or not. This commit adds a check to the allocation function and
handles the error accordingly.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug description:
When running "ethtool -x <if_name>" the key shows up as all zeros.
When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to
set the key and then try to retrieve it using "ethtool -x <if_name>" then
we return the correct key because we return the one we saved.
Bug cause:
We don't fetch the key from the device but instead return the key
that we have saved internally which is by default set to zero upon
allocation.
Fix:
This commit fixes the issue by initializing the key to a random value
using netdev_rss_key_fill().
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of the driver calls skb_tx_timestamp()to add a
software tx timestamp to the skb, however the software-transmit capability
is not reported in ethtool -T.
This commit updates the ethtool structure to report the software-transmit
capability in ethtool -T using the standard ethtool_op_get_ts_info().
This function reports all software timestamping capabilities (tx and rx),
as well as setting phc_index = -1. phc_index is the index of the PTP
hardware clock device that will be used for hardware timestamps. Since we
don't have such a device in ENA, using the default -1 value is the correct
setting.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From the documentation of round_jiffies():
"Rounds a time delta in the future (in jiffies) up or down to
(approximately) full seconds. This is useful for timers for which
the exact time they fire does not matter too much, as long as
they fire approximately every X seconds.
By rounding these timers to whole seconds, all such timers will fire
at the same time, rather than at various times spread out. The goal
of this is to have the CPU wake up less, which saves power."
There are 2 parts to this patch:
================================
Part 1:
-------
In our case we need timer_service to be called approximately every
X=1 seconds, and the exact time does not matter, so using round_jiffies()
is the right way to go.
Therefore we add round_jiffies() to the mod_timer() in ena_timer_service().
Part 2:
-------
round_jiffies() is used in check_for_missing_keep_alive() when
getting the jiffies of the expiration of the keep_alive timeout. Here it
is actually a mistake to use round_jiffies() because we want the exact
time when keep_alive should expire and not an approximate rounded time,
which can cause early, false positive, timeouts.
Therefore we remove round_jiffies() in the calculation of
keep_alive_expired() in check_for_missing_keep_alive().
Fixes: 82ef30f13b ("net: ena: add hardware hints capability to the driver")
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ethtool -X is called without an hkey, ena_com_fill_hash_function()
is called with key=NULL, which is passed to memcpy causing a crash.
This commit fixes this issue by checking key is not NULL.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d9d6a9aed3 ("i40e: Fix virtchnl_queue_select bitmap
validation") introduced a necessary change for verifying how queue
bitmaps from the iavf driver get validated. Unfortunately, the
conditional was reversed. Fix this.
Fixes: d9d6a9aed3 ("i40e: Fix virtchnl_queue_select bitmap validation")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.
The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work. This is done based on the knowledge that it
has exactly 2 bulk endpoints. QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.
The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs. Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for unique interrupt names, after testing on a few
devices, it was assumed 32 characters would be sufficient. This
assumption turned out to be incorrect, ZII RDU2 for example uses a
device base name of mv88e6xxx-30be0000.ethernet-1:0, leaving no space
for post fixes such as -g1-atu-prob and -watchdog. The names then
become identical, defeating the point of the patch.
Increase the length of the string to 64 charactoes.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 3095383a8a ("net: dsa: mv88e6xxx: Unique IRQ name")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f25e1392fd removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
And interface 0 will be rejected based on too few endpoints for the
pre-production variant:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Fixes: f25e1392fd ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl4+lTYPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3nQcQAJm91+6hZbmMjlBySGS7ISjYvOcrI/hMgiOl
uhhEP0Dcylvf9A9x3wcIbLwixe+2pvie9DQh2u5F80ShYimidtFi/2xCfuTb9fKu
sxxKjrXWyVKhkpW0z+tedY08ftVhkwwcyD4m2C7uVl6AwTP7c367vFeU7XjF2APn
drfgmgbjm8U3XbSyAqv+k6z6tyqaCnFM7vbPupSKHgHJ3mfByxOa+XyBN2RdgBbs
0KrVfbXGv80zFIFrMPwaWG7G52bu7K68nVdgy44MpKdRZ6QTjhnR+kerFxHsYgV4
bM55Fya52nTCSTGdKaQakDtKwbAUdCDTSkxgOHGcQoyFi0R/VaEUJtcysnvLbI6c
+n/yFIzGyEdXcvIzfv2SoDYhogw19I6RR/M9K5Ni29eazkDVYx2z3rI+2QYeqCiF
u7cq52gW6JLP0SI/9kuUrRFiR8v19Ixap7qokAxgqQwYB3NzT8a7WsYPkzdpDZGQ
ETSDFMyBWT6UvBe/HWkQluBabbet53rG8BF0OHFrQuMK0u/ieKgSGuTB9XN2djEW
PHMOMz2vhi+8XTfpkskhF2tTxlA/k4R6QwCdIMpIkMRVnVQCh1XdPr3Fi2NrgB+S
kIXHD4vV6zLYh04zHyKewSPHAXWgraFpg2qKnvL5+KWMTnW6QH+RNjOt9xKDNXOd
+iDXpOad
=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
The configuration of the OCTEONTX XCV_DLL_CTL register via
xcv_init_hw() is such that the RGMII RX delay is bypassed
leaving the RGMII TX delay enabled in the MAC:
/* Configure DLL - enable or bypass
* TX no bypass, RX bypass
*/
cfg = readq_relaxed(xcv->reg_base + XCV_DLL_CTL);
cfg &= ~0xFF03;
cfg |= CLKRX_BYP;
writeq_relaxed(cfg, xcv->reg_base + XCV_DLL_CTL);
This would coorespond to a interface type of PHY_INTERFACE_MODE_RGMII_RXID
and not PHY_INTERFACE_MODE_RGMII.
Fixing this allows RGMII PHY drivers to do the right thing (enable
RX delay in the PHY) instead of erroneously enabling both delays in the
PHY.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for v5.6. Buffer overflow fixes to mwifiex, quite a
few functionality fixes to iwlwifi and smaller fixes to other drivers.
mwifiex
* fix an unlock from a previous security fix
* fix two buffer overflows
libertas
* fix two bugs from previous security fixes
iwlwifi
* fix module removal with multiple NICs
* don't treat IGTK removal failure as an error
* avoid FW crashes due to DTS measurement races
* fix a potential use after free in FTM code
* prevent a NULL pointer dereference in iwl_mvm_cfg_he_sta()
* fix TDLS discovery
* check all CPUs when trying to detect an error during resume
rtw88
* fix clang warning
mt76
* fix reading of max_nss value from a register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJePoxJAAoJEG4XJFUm622b7a4H/2t/K/AmDv+j2mGos+2oVlSh
RFIXBjYs4GY5NGdLQx56qfiQzlgn8NAWwQqwhtoyVxnJTZjhmQkfMpJIw14tbFB1
OwHd+q7y7jXY9v7YBPlyqCxkzQL3u+GrzFIb04cXrSdzqh+5qWk4Zn7F6ZYJ1vwb
xRDOJfOE/a9GGzzY5+iwxyZ6Y1E+OjbgT4Ps5YUaotH1iMGza7NPu6s+UkULkyRo
ylbiOR9u6jOiwUkSxUz+GGiXKJ9BQTLKm5kLM7lO5I49AcZb5UOIKJaJxHN0hMwj
uprqUsqtbO+bv8SKAjKLR/yQf2gmB+pSSeAmmfJ8ov5igg2g12sNfdy8ScWLks8=
=FiiT
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
First set of fixes for v5.6. Buffer overflow fixes to mwifiex, quite a
few functionality fixes to iwlwifi and smaller fixes to other drivers.
mwifiex
* fix an unlock from a previous security fix
* fix two buffer overflows
libertas
* fix two bugs from previous security fixes
iwlwifi
* fix module removal with multiple NICs
* don't treat IGTK removal failure as an error
* avoid FW crashes due to DTS measurement races
* fix a potential use after free in FTM code
* prevent a NULL pointer dereference in iwl_mvm_cfg_he_sta()
* fix TDLS discovery
* check all CPUs when trying to detect an error during resume
rtw88
* fix clang warning
mt76
* fix reading of max_nss value from a register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-02-07
The following pull-request contains BPF updates for your *net* tree.
We've added 15 non-merge commits during the last 10 day(s) which contain
a total of 12 files changed, 114 insertions(+), 31 deletions(-).
The main changes are:
1) Various BPF sockmap fixes related to RCU handling in the map's tear-
down code, from Jakub Sitnicki.
2) Fix macro state explosion in BPF sk_storage map when calculating its
bucket_log on allocation, from Martin KaFai Lau.
3) Fix potential BPF sockmap update race by rechecking socket's established
state under lock, from Lorenz Bauer.
4) Fix crash in bpftool on missing xlated instructions when kptr_restrict
sysctl is set, from Toke Høiland-Jørgensen.
5) Fix i40e's XSK wakeup code to return proper error in busy state and
various misc fixes in xdpsock BPF sample code, from Maciej Fijalkowski.
6) Fix the way modifiers are skipped in BTF in the verifier while walking
pointers to avoid program rejection, from Alexei Starovoitov.
7) Fix Makefile for runqslower BPF tool to i) rebuild on libbpf changes and
ii) to fix undefined reference linker errors for older gcc version due to
order of passed gcc parameters, from Yulia Kartseva and Song Liu.
8) Fix a trampoline_count BPF kselftest warning about missing braces around
initializer, from Andrii Nakryiko.
9) Fix up redundant "HAVE" prefix from large INSN limit kernel probe in
bpftool, from Michal Rostecki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix u8 cast reading max_nss from MT_TOP_STRAP_STA register in
mt7615_eeprom_parse_hw_cap routine
Fixes: acf5457fd9 ("mt76: mt7615: read {tx,rx} mask from eeprom")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case devlink_dpipe_entry_ctx_prepare() failed, release RTNL that was
previously taken and free the memory allocated by
mlxsw_sp_erif_entry_prepare().
Fixes: 2ba5999f00 ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading the number of gearboxes from the hardware, the driver does
not validate the returned 'device type' field. The driver can therefore
wrongly assume that the queried devices are gearboxes.
On Spectrum-3 systems that support different types of devices, this can
prevent the driver from loading, as it will try to query the
temperature sensors from devices which it assumes are gearboxes and in
fact are not.
For example:
[ 218.129230] mlxsw_minimal 2-0048: Reg cmd access status failed (status=7(bad parameter))
[ 218.138282] mlxsw_minimal 2-0048: Reg cmd access failed (reg_id=900a(mtmp),type=write)
[ 218.147131] mlxsw_minimal 2-0048: Failed to setup temp sensor number 256
[ 218.534480] mlxsw_minimal 2-0048: Fail to register core bus
[ 218.540714] mlxsw_minimal: probe of 2-0048 failed with error -5
Fix this by validating the 'device type' field.
Fixes: 2e265a8b6c ("mlxsw: core: Extend hwmon interface with inter-connect temperature attributes")
Fixes: f14f4e621b ("mlxsw: core: Extend thermal core with per inter-connect device thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike IPv4, in IPv6 there is no unique structure to represent the
nexthop and both the route and nexthop information are squashed to the
same structure ('struct fib6_info'). In order to improve resource
utilization the driver consolidates identical nexthop groups to the same
internal representation of a nexthop group.
Therefore, when the offload indication of a nexthop changes, the driver
needs to iterate over all the linked fib6_info and toggle their offload
flag accordingly.
During abort, all the routes are removed from the device and unlinked
from their nexthop group. The offload indication is cleared just before
the group is destroyed, but by that time no fib6_info is linked to the
group and the offload indication remains set.
Fix this by clearing the offload indication just before dropping the
reference from the nexthop.
Fixes: ee5a0448e7 ("mlxsw: spectrum_router: Set hardware flags for routes")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses the same table to represent both the main and local
routing tables. Prevent routes in the main table from replacing routes
in the local table to reflect the fact that the local table is consulted
first during lookup.
Fixes: b6a1d871d3 ("mlxsw: spectrum_router: Start using new IPv4 route notifications")
Fixes: dacad7b34b ("mlxsw: spectrum_router: Start using new IPv6 route notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop removing modes that are not supported on the system interface
when the connected PHY is capable of rate adaptation. This addresses
an issue with the LS1046ARDB board 10G interface no longer working
with an 1G link partner after autonegotiation support was added
for the Aquantia PHY on board in
commit 09c4c57f7b ("net: phy: aquantia: add support for auto-negotiation configuration")
Before this commit the values advertised by the PHY were not
influenced by the dpaa_eth driver removal of system-side unsupported
modes as the aqr_config_aneg() was basically a no-op. After this
commit, the modes removed by the dpaa_eth driver were no longer
advertised thus autonegotiation with 1G link partners failed.
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch to support passive mode converter did not take care the
phy interface configuration in PCI platform data. Hence, converting all
the PCI platform data from plat->interface to plat->phy_interface as the
default mode is meant for PHY.
Fixes: 0060c87833 ("net: stmmac: implement support for passive mode converters via dt")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 0efedbf11f ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Verma, Aashish <aashishx.verma@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should always do a read of current value of XGMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: 3cd1cfcba2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should always do a read of current value of GMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: c1be0022df ("net: stmmac: Add VLAN HASH filtering support in GMAC4+")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of XDP_SETUP_PROG has already incremented refcnt in
__bpf_prog_get(), so drivers should only increment refcnt by
num_queues - 1.
To fix the issue, update netvsc_xdp_set() to add the correct number
to refcnt.
Hold a refcnt in netvsc_xdp_set()’s other caller, netvsc_attach().
And, do the same in netvsc_vf_setxdp(). Otherwise, every time when VF is
removed and added from the host side, the refcnt will be decreased by one,
which may cause page fault when unloading xdp program.
Fixes: 351e158139 ("hv_netvsc: Add XDP support")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c645 ("net: dsa: b53: Properly account for VLAN filtering")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It forgot to reduce the value of the variable retry in a while loop
in the ethqos_configure() function. It may cause an endless loop and
without timeout.
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deprecate the generic TLS cap bit, use the new TX-specific
TLS cap bit instead.
Fixes: a12ff35e0f ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For a cyclic work queue, when not requesting a completion per WQE,
a single CQE might indicate the completion of several WQEs.
However, in case some WQE in the batch causes an error, then an error
completion is issued, breaking the batch, and pointing to the offending
WQE in the wqe_counter field.
Hence, WQE-specific error CQE handling (like printing, breaking, etc...)
should be performed only for the last WQE in batch.
Fixes: 130c7b46c9 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Fixes: fd9b4be800 ("net/mlx5e: RX, Support multiple outstanding UMR posts")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
SA context is allocated at mlx5_fpga_ipsec_create_sa_ctx,
however the counterpart mlx5_fpga_ipsec_delete_sa_ctx function
nullifies sa_ctx pointer without freeing the memory allocated,
hence the memory leak.
Fix by free SA context when the SA is released.
Fixes: d6c4f0298c ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The function mlx5_fpga_esp_validate_xfrm_attrs is wrongly used
with negative negation as zero value indicates success but it
used as failure return value instead.
Fix by remove the unary not negation operator.
Fixes: 05564d0ae0 ("net/mlx5: Add flow-steering commands for FPGA IPSec implementation")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After a number of suspend and resume cycles, it is possible for the RBUF
to be stuck in Wake-on-LAN mode, despite the MPD enable bit being
cleared which instructed the RBUF to exit that mode.
Avoid creating that problematic condition by clearing the RX_EN and
TX_EN bits in the UniMAC prior to disable the Magic Packet Detector
logic which is guaranteed to make the RBUF exit Wake-on-LAN mode.
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d3654 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move rx_dropped and rx_errors counters in mvneta_pcpu_stats in order to
avoid possible races updating statistics
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added debugfs entry to show the tls stats.
Signed-off-by: Devulapally Shiva Krishna <shiva@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EAGAIN instead of -ENETDOWN to provide a slightly milder
information to user space so that an application will know to retry the
syscall when __I40E_CONFIG_BUSY bit is set on pf->state.
Fixes: b3873a5be7 ("net/i40e: Fix concurrency issues between config flow and XSK")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20200205045834.56795-2-maciej.fijalkowski@intel.com
commit cedeac9df4 ("qed: Add support for Timestamping the unicast
PTP packets.") handles the timestamping of L4 ptp packets only.
This patch adds driver changes to detect/timestamp both L2/L4 unicast
PTP packets.
Fixes: cedeac9df4 ("qed: Add support for Timestamping the unicast PTP packets.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM_MAX_TX_LEN currently resolves to 0x3FF8 for any IP version supporting
TSO with full 14bits of length field in payload descriptor. But an IP
errata causes false amba_error (bit 6 of ISR) when length in payload
descriptors is specified above 16387. The error occurs because the DMA
falsely concludes that there is not enough space in SRAM for incoming
payload. These errors were observed continuously under stress of large
packets using iperf on a version where SRAM was 16K for each queue. This
errata will be documented shortly and affects all versions since TSO
functionality was added. Hence limit the max length to 0x3FC0 (rounded).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP TSO implementation does NOT require the length to be a
multiple of 8. That is only a requirement for UFO as per IP
documentation. Hence, exit macb_features_check function in the
beginning if the protocol is not UDP. Only when it is UDP,
proceed further to the alignment checks. Update comments to
reflect the same. Also remove dead code checking for protocol
TCP when calculating header length.
Fixes: 1629dd4f76 ("cadence: Add LSO support.")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot managed to send an IPX packet through bond_alb_xmit()
and af_packet and triggered a use-after-free.
First, bond_alb_xmit() was using ipx_hdr() helper to reach
the IPX header, but ipx_hdr() was using the transport offset
instead of the network offset. In the particular syzbot
report transport offset was 0xFFFF
This patch removes ipx_hdr() since it was only (mis)used from bonding.
Then we need to make sure IPv4/IPv6/IPX headers are pulled
in skb->head before dereferencing anything.
BUG: KASAN: use-after-free in bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
Read of size 2 at addr ffff8801ce56dfff by task syz-executor.2/18108
(if (ipx_hdr(skb)->ipx_checksum != IPX_NO_CHECKSUM) ...)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
[<ffffffff8441fc42>] __dump_stack lib/dump_stack.c:17 [inline]
[<ffffffff8441fc42>] dump_stack+0x14d/0x20b lib/dump_stack.c:53
[<ffffffff81a7dec4>] print_address_description+0x6f/0x20b mm/kasan/report.c:282
[<ffffffff81a7e0ec>] kasan_report_error mm/kasan/report.c:380 [inline]
[<ffffffff81a7e0ec>] kasan_report mm/kasan/report.c:438 [inline]
[<ffffffff81a7e0ec>] kasan_report.cold+0x8c/0x2a0 mm/kasan/report.c:422
[<ffffffff81a7dc4f>] __asan_report_load_n_noabort+0xf/0x20 mm/kasan/report.c:469
[<ffffffff82c8c00a>] bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
[<ffffffff82c60c74>] __bond_start_xmit drivers/net/bonding/bond_main.c:4199 [inline]
[<ffffffff82c60c74>] bond_start_xmit+0x4f4/0x1570 drivers/net/bonding/bond_main.c:4224
[<ffffffff83baa558>] __netdev_start_xmit include/linux/netdevice.h:4525 [inline]
[<ffffffff83baa558>] netdev_start_xmit include/linux/netdevice.h:4539 [inline]
[<ffffffff83baa558>] xmit_one net/core/dev.c:3611 [inline]
[<ffffffff83baa558>] dev_hard_start_xmit+0x168/0x910 net/core/dev.c:3627
[<ffffffff83bacf35>] __dev_queue_xmit+0x1f55/0x33b0 net/core/dev.c:4238
[<ffffffff83bae3a8>] dev_queue_xmit+0x18/0x20 net/core/dev.c:4278
[<ffffffff84339189>] packet_snd net/packet/af_packet.c:3226 [inline]
[<ffffffff84339189>] packet_sendmsg+0x4919/0x70b0 net/packet/af_packet.c:3252
[<ffffffff83b1ac0c>] sock_sendmsg_nosec net/socket.c:673 [inline]
[<ffffffff83b1ac0c>] sock_sendmsg+0x12c/0x160 net/socket.c:684
[<ffffffff83b1f5a2>] __sys_sendto+0x262/0x380 net/socket.c:1996
[<ffffffff83b1f700>] SYSC_sendto net/socket.c:2008 [inline]
[<ffffffff83b1f700>] SyS_sendto+0x40/0x60 net/socket.c:2004
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive frame length calculation uses a wrong mask to calculate the
length of the received frames.
Per spec table 4-1 the length is contained in the FL (Frame Length)
field in bits 30:16.
This didn't show up as an issue so far since frames were limited to
1500 bytes which falls within the 11 bit window.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our static-static calculation returns a failure if the public key is of
low order. We check for this when peers are added, and don't allow them
to be added if they're low order, except in the case where we haven't
yet been given a private key. In that case, we would defer the removal
of the peer until we're given a private key, since at that point we're
doing new static-static calculations which incur failures we can act on.
This meant, however, that we wound up removing peers rather late in the
configuration flow.
Syzkaller points out that peer_remove calls flush_workqueue, which in
turn might then wait for sending a handshake initiation to complete.
Since handshake initiation needs the static identity lock, holding the
static identity lock while calling peer_remove can result in a rare
deadlock. We have precisely this case in this situation of late-stage
peer removal based on an invalid public key. We can't drop the lock when
removing, because then incoming handshakes might interact with a bogus
static-static calculation.
While the band-aid patch for this would involve breaking up the peer
removal into two steps like wg_peer_remove_all does, in order to solve
the locking issue, there's actually a much more elegant way of fixing
this:
If the static-static calculation succeeds with one private key, it
*must* succeed with all others, because all 32-byte strings map to valid
private keys, thanks to clamping. That means we can get rid of this
silly dance and locking headaches of removing peers late in the
configuration flow, and instead just reject them early on, regardless of
whether the device has yet been assigned a private key. For the case
where the device doesn't yet have a private key, we safely use zeros
just for the purposes of checking for low order points by way of
checking the output of the calculation.
The following PoC will trigger the deadlock:
ip link add wg0 type wireguard
ip addr add 10.0.0.1/24 dev wg0
ip link set wg0 up
ping -f 10.0.0.2 &
while true; do
wg set wg0 private-key /dev/null peer AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA= allowed-ips 10.0.0.0/24 endpoint 10.0.0.3:1234
wg set wg0 private-key <(echo AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA=)
done
[ 0.949105] ======================================================
[ 0.949550] WARNING: possible circular locking dependency detected
[ 0.950143] 5.5.0-debug+ #18 Not tainted
[ 0.950431] ------------------------------------------------------
[ 0.950959] wg/89 is trying to acquire lock:
[ 0.951252] ffff8880333e2128 ((wq_completion)wg-kex-wg0){+.+.}, at: flush_workqueue+0xe3/0x12f0
[ 0.951865]
[ 0.951865] but task is already holding lock:
[ 0.952280] ffff888032819bc0 (&wg->static_identity.lock){++++}, at: wg_set_device+0x95d/0xcc0
[ 0.953011]
[ 0.953011] which lock already depends on the new lock.
[ 0.953011]
[ 0.953651]
[ 0.953651] the existing dependency chain (in reverse order) is:
[ 0.954292]
[ 0.954292] -> #2 (&wg->static_identity.lock){++++}:
[ 0.954804] lock_acquire+0x127/0x350
[ 0.955133] down_read+0x83/0x410
[ 0.955428] wg_noise_handshake_create_initiation+0x97/0x700
[ 0.955885] wg_packet_send_handshake_initiation+0x13a/0x280
[ 0.956401] wg_packet_handshake_send_worker+0x10/0x20
[ 0.956841] process_one_work+0x806/0x1500
[ 0.957167] worker_thread+0x8c/0xcb0
[ 0.957549] kthread+0x2ee/0x3b0
[ 0.957792] ret_from_fork+0x24/0x30
[ 0.958234]
[ 0.958234] -> #1 ((work_completion)(&peer->transmit_handshake_work)){+.+.}:
[ 0.958808] lock_acquire+0x127/0x350
[ 0.959075] process_one_work+0x7ab/0x1500
[ 0.959369] worker_thread+0x8c/0xcb0
[ 0.959639] kthread+0x2ee/0x3b0
[ 0.959896] ret_from_fork+0x24/0x30
[ 0.960346]
[ 0.960346] -> #0 ((wq_completion)wg-kex-wg0){+.+.}:
[ 0.960945] check_prev_add+0x167/0x1e20
[ 0.961351] __lock_acquire+0x2012/0x3170
[ 0.961725] lock_acquire+0x127/0x350
[ 0.961990] flush_workqueue+0x106/0x12f0
[ 0.962280] peer_remove_after_dead+0x160/0x220
[ 0.962600] wg_set_device+0xa24/0xcc0
[ 0.962994] genl_rcv_msg+0x52f/0xe90
[ 0.963298] netlink_rcv_skb+0x111/0x320
[ 0.963618] genl_rcv+0x1f/0x30
[ 0.963853] netlink_unicast+0x3f6/0x610
[ 0.964245] netlink_sendmsg+0x700/0xb80
[ 0.964586] __sys_sendto+0x1dd/0x2c0
[ 0.964854] __x64_sys_sendto+0xd8/0x1b0
[ 0.965141] do_syscall_64+0x90/0xd9a
[ 0.965408] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 0.965769]
[ 0.965769] other info that might help us debug this:
[ 0.965769]
[ 0.966337] Chain exists of:
[ 0.966337] (wq_completion)wg-kex-wg0 --> (work_completion)(&peer->transmit_handshake_work) --> &wg->static_identity.lock
[ 0.966337]
[ 0.967417] Possible unsafe locking scenario:
[ 0.967417]
[ 0.967836] CPU0 CPU1
[ 0.968155] ---- ----
[ 0.968497] lock(&wg->static_identity.lock);
[ 0.968779] lock((work_completion)(&peer->transmit_handshake_work));
[ 0.969345] lock(&wg->static_identity.lock);
[ 0.969809] lock((wq_completion)wg-kex-wg0);
[ 0.970146]
[ 0.970146] *** DEADLOCK ***
[ 0.970146]
[ 0.970531] 5 locks held by wg/89:
[ 0.970908] #0: ffffffff827433c8 (cb_lock){++++}, at: genl_rcv+0x10/0x30
[ 0.971400] #1: ffffffff82743480 (genl_mutex){+.+.}, at: genl_rcv_msg+0x642/0xe90
[ 0.971924] #2: ffffffff827160c0 (rtnl_mutex){+.+.}, at: wg_set_device+0x9f/0xcc0
[ 0.972488] #3: ffff888032819de0 (&wg->device_update_lock){+.+.}, at: wg_set_device+0xb0/0xcc0
[ 0.973095] #4: ffff888032819bc0 (&wg->static_identity.lock){++++}, at: wg_set_device+0x95d/0xcc0
[ 0.973653]
[ 0.973653] stack backtrace:
[ 0.973932] CPU: 1 PID: 89 Comm: wg Not tainted 5.5.0-debug+ #18
[ 0.974476] Call Trace:
[ 0.974638] dump_stack+0x97/0xe0
[ 0.974869] check_noncircular+0x312/0x3e0
[ 0.975132] ? print_circular_bug+0x1f0/0x1f0
[ 0.975410] ? __kernel_text_address+0x9/0x30
[ 0.975727] ? unwind_get_return_address+0x51/0x90
[ 0.976024] check_prev_add+0x167/0x1e20
[ 0.976367] ? graph_lock+0x70/0x160
[ 0.976682] __lock_acquire+0x2012/0x3170
[ 0.976998] ? register_lock_class+0x1140/0x1140
[ 0.977323] lock_acquire+0x127/0x350
[ 0.977627] ? flush_workqueue+0xe3/0x12f0
[ 0.977890] flush_workqueue+0x106/0x12f0
[ 0.978147] ? flush_workqueue+0xe3/0x12f0
[ 0.978410] ? find_held_lock+0x2c/0x110
[ 0.978662] ? lock_downgrade+0x6e0/0x6e0
[ 0.978919] ? queue_rcu_work+0x60/0x60
[ 0.979166] ? netif_napi_del+0x151/0x3b0
[ 0.979501] ? peer_remove_after_dead+0x160/0x220
[ 0.979871] peer_remove_after_dead+0x160/0x220
[ 0.980232] wg_set_device+0xa24/0xcc0
[ 0.980516] ? deref_stack_reg+0x8e/0xc0
[ 0.980801] ? set_peer+0xe10/0xe10
[ 0.981040] ? __ww_mutex_check_waiters+0x150/0x150
[ 0.981430] ? __nla_validate_parse+0x163/0x270
[ 0.981719] ? genl_family_rcv_msg_attrs_parse+0x13f/0x310
[ 0.982078] genl_rcv_msg+0x52f/0xe90
[ 0.982348] ? genl_family_rcv_msg_attrs_parse+0x310/0x310
[ 0.982690] ? register_lock_class+0x1140/0x1140
[ 0.983049] netlink_rcv_skb+0x111/0x320
[ 0.983298] ? genl_family_rcv_msg_attrs_parse+0x310/0x310
[ 0.983645] ? netlink_ack+0x880/0x880
[ 0.983888] genl_rcv+0x1f/0x30
[ 0.984168] netlink_unicast+0x3f6/0x610
[ 0.984443] ? netlink_detachskb+0x60/0x60
[ 0.984729] ? find_held_lock+0x2c/0x110
[ 0.984976] netlink_sendmsg+0x700/0xb80
[ 0.985220] ? netlink_broadcast_filtered+0xa60/0xa60
[ 0.985533] __sys_sendto+0x1dd/0x2c0
[ 0.985763] ? __x64_sys_getpeername+0xb0/0xb0
[ 0.986039] ? sockfd_lookup_light+0x17/0x160
[ 0.986397] ? __sys_recvmsg+0x8c/0xf0
[ 0.986711] ? __sys_recvmsg_sock+0xd0/0xd0
[ 0.987018] __x64_sys_sendto+0xd8/0x1b0
[ 0.987283] ? lockdep_hardirqs_on+0x39b/0x5a0
[ 0.987666] do_syscall_64+0x90/0xd9a
[ 0.987903] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 0.988223] RIP: 0033:0x7fe77c12003e
[ 0.988508] Code: c3 8b 07 85 c0 75 24 49 89 fb 48 89 f0 48 89 d7 48 89 ce 4c 89 c2 4d 89 ca 4c 8b 44 24 08 4c 8b 4c 24 10 4c 4
[ 0.989666] RSP: 002b:00007fffada2ed58 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[ 0.990137] RAX: ffffffffffffffda RBX: 00007fe77c159d48 RCX: 00007fe77c12003e
[ 0.990583] RDX: 0000000000000040 RSI: 000055fd1d38e020 RDI: 0000000000000004
[ 0.991091] RBP: 000055fd1d38e020 R08: 000055fd1cb63358 R09: 000000000000000c
[ 0.991568] R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000002c
[ 0.992014] R13: 0000000000000004 R14: 000055fd1d38e020 R15: 0000000000000001
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/netdevsim/dev.c:937:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes: 6556ff32f1 ("netdevsim: use IS_ERR instead of IS_ERR_OR_NULL for debugfs")
CC: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ce5ebd24d ("mfd: ioc3: Add driver for SGI IOC3 chip") moved
request_irq() from ioc3_open into probe function, but forgot to remove
free_irq() from ioc3_close.
Fixes: 0ce5ebd24d ("mfd: ioc3: Add driver for SGI IOC3 chip")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Use after free in rxrpc_put_local(), from David Howells.
2) Fix 64-bit division error in mlxsw, from Nathan Chancellor.
3) Make sure we clear various bits of TCP state in response to
tcp_disconnect(). From Eric Dumazet.
4) Fix netlink attribute policy in cls_rsvp, from Eric Dumazet.
5) txtimer must be deleted in stmmac suspend(), from Nicolin Chen.
6) Fix TC queue mapping in bnxt_en driver, from Michael Chan.
7) Various netdevsim fixes from Taehee Yoo (use of uninitialized data,
snapshot panics, stack out of bounds, etc.)
8) cls_tcindex changes hash table size after allocating the table, fix
from Cong Wang.
9) Fix regression in the enforcement of session ID uniqueness in l2tp.
We only have to enforce uniqueness for IP based tunnels not UDP
ones. From Ridge Kennedy.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
gtp: use __GFP_NOWARN to avoid memalloc warning
l2tp: Allow duplicate session creation with UDP
r8152: Add MAC passthrough support to new device
net_sched: fix an OOB access in cls_tcindex
qed: Remove set but not used variable 'p_link'
tc-testing: add missing 'nsPlugin' to basic.json
tc-testing: fix eBPF tests failure on linux fresh clones
net: hsr: fix possible NULL deref in hsr_handle_frame()
netdevsim: remove unused sdev code
netdevsim: use __GFP_NOWARN to avoid memalloc warning
netdevsim: use IS_ERR instead of IS_ERR_OR_NULL for debugfs
netdevsim: fix stack-out-of-bounds in nsim_dev_debugfs_init()
netdevsim: fix panic in nsim_dev_take_snapshot_write()
netdevsim: disable devlink reload when resources are being used
netdevsim: fix using uninitialized resources
bnxt_en: Fix TC queue mapping.
bnxt_en: Fix logic that disables Bus Master during firmware reset.
bnxt_en: Fix RDMA driver failure with SRIOV after firmware reset.
bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.
net: stmmac: Delete txtimer in suspend()
...
Paul Cercueil