If the initial fbdev configuration (intel_fbdev_initial_config()) runs
and there still no sink connected it will cause
drm_fb_helper_initial_config() to return 0 as no error happened (but
internally the return is -EAGAIN). Because no framebuffer was
allocated, when a sink is connected intel_fbdev_output_poll_changed()
will not execute drm_fb_helper_hotplug_event() that would trigger
another try to do the initial fbdev configuration.
So here allowing drm_fb_helper_hotplug_event() to be executed when there
is no framebuffer allocated and fbdev was not set up yet.
This issue also happens when a MST DP sink is connected since boot, as
the MST topology is discovered in parallel if
intel_fbdev_initial_config() is executed before the first sink MST is
discovered it will cause this same issue.
This is a follow-up patch of
https://patchwork.freedesktop.org/patch/196089/
Changes from v1:
- not creating a dump framebuffer anymore, instead just allowing
drm_fb_helper_hotplug_event() to execute when fbdev is not setup yet.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: frederik <frederik.schwan@linux.com> # 4.15.17
Tested-by: Ian Pilcher <arequipeno@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418234158.9388-1-jose.souza@intel.com
(cherry picked from commit df9e652174)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We use jiffies to determine when wait expires. However
Imre did find out that jiffies can and will do a >1
increments on certain situations [1]. When this happens
in a wait_for loop, we return timeout errorneously
much earlier than what the real wallclock would say.
We can't afford our waits to timeout prematurely.
Discard jiffies and change to ktime to detect timeouts.
v2: added bugzilla entry (Imre), added stable (Chris)
Reported-by: Imre Deak <imre.deak@intel.com>
References: https://lkml.org/lkml/2018/4/18/798 [1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105771
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423113754.28424-1-mika.kuoppala@linux.intel.com
(cherry picked from commit 3085982c6b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The DMC FW specific part of display WA#1183 is supposed to be enabled
whenever enabling DC5 or DC6, so move it to the DC6 enable function
from the DC6 disable function.
I noticed this after Daniel's patch to remove the unused
skl_disable_dc6() function.
Fixes: 53421c2fe9 ("drm/i915: Apply Display WA #1183 on skl, kbl, and cfl")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419155109.29451-1-imre.deak@intel.com
(cherry picked from commit b49be6622f)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
In GLK when the device boots with only 1366x768 panel without audio, HDA
codec doesn't come up. In this case, the CDCLK is less than twice the
BCLK. Even though audio isn't being enabled, having a too low CDCLK
leads to audio probe failing altogether.
Require CDCLK to be at least twice the BLCK regardless of audio. This is
a minimal fix to improve things. Unfortunately, this a) leads to too
high CDCLK being used when audio is not used, and b) is still not enough
to fix audio probe when no outputs are connected at probe time.
The proper fix would be to increase CDCLK dynamically from the audio
component hooks.
v2:
- Address comment (Jani)
- New design approach
v3: - Typo fix on top of v1
v4 by Jani: rewrite commit message, add comment in code
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@gmail.com>
Cc: Wenkai Du <wenkai.du@intel.com>
Reviewed-by: Wenkai Du <wenkai.du@intel.com>
Tested-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102937
Signed-off-by: Abhay Kumar <abhay.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418103707.14645-1-jani.nikula@intel.com
(cherry picked from commit 2a5b95b448)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=SkQU
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Exynos, i915, vc4, amdgpu fixes.
i915:
- an oops fix
- two race fixes
- some gvt fixes
amdgpu:
- dark screen fix
- clk/voltage fix
- vega12 smu fix
vc4:
- memory leak fix
exynos just drops some code"
* tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux: (23 commits)
drm/amd/powerplay: header file interface to SMU update
drm/amd/pp: Fix bug voltage can't be OD separately on VI
drm/amd/display: Don't program bypass on linear regamma LUT
drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
drm/i915/audio: Fix audio detection issue on GLK
drm/i915: Call i915_perf_fini() on init_hw error unwind
drm/i915/bios: filter out invalid DDC pins from VBT child devices
drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
drm/exynos: exynos_drm_fb -> drm_framebuffer
drm/exynos: Move dma_addr out of exynos_drm_fb
drm/exynos: Move GEM BOs to drm_framebuffer
drm: Fix HDCP downstream dev count read
drm/vc4: Fix memory leak during BO teardown
drm/i915/execlists: Clear user-active flag on preemption completion
drm/i915/gvt: Add drm_format_mod update
drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
drm/i915/gvt: Delete redundant error message in fb_decode.c
drm/i915/gvt: Cancel dma map when resetting ggtt entries
drm/i915/gvt: Missed to cancel dma map for ggtt entries
...
On Geminilake, sometimes audio card is not getting
detected after reboot. This is a spurious issue happening on
Geminilake. HW codec and HD audio controller link was going
out of sync for which there was a fix in i915 driver but
was not getting invoked for GLK. Extending this fix to GLK as well.
Tested by Du,Wenkai on GLK board.
Bspec: 21829
v2: Instead of checking GEN9_BC, BXT and GLK macros, use IS_GEN9 macro (Jani N)
Cc: <stable@vger.kernel.org> # b651bd2a3a ("drm/i915/audio: Fix audio enumeration issue on BXT")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Abhay Kumar <abhay.Kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523989338-29677-1-git-send-email-gaurav.k.singh@intel.com
(cherry picked from commit 8221229046)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We have to cleanup after i915_perf_init(), even on the error path, as it
passes a pointer into the module to the sysfs core. If we fail to
unregister the sysctl table, we leave a dangling pointer which then may
explode anytime later.
Fixes: 9f9b2792b6 ("drm/i915/perf: reuse timestamp frequency from device info")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180414091233.32224-1-chris@chris-wilson.co.uk
(cherry picked from commit 9f172f6fbd)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
While thinking about sporadic failures of perf_pmu/rc6-runtime-pm* tests
on some CI machines I have concluded that: a) the PMU readout of RC6 can
race against runtime PM transitions, and b) there are other reasons than
being runtime suspended which can cause intel_runtime_pm_get_if_in_use to
fail.
Therefore when estimating RC6 the code needs to assert we are indeed in
suspended state, and if not, the best we can do is return the last known
RC6 value.
Without this check we can calculate the estimated value based on un-
initialized or inappropriate internal state, which can result in over-
estimation, or in any case incorrect value being returned.
v2:
* Re-arrange the code a bit to avoid second unlock and return branch.
(Chris Wilson)
v3:
* Insert some strategic blank lines and improve commit msg.
(Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 1fe699e301 ("drm/i915/pmu: Fix sleep under atomic in RC6 readout")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105010
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180410112704.24462-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 2924bdee21)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Along the eb_lookup_vmas() error path, the return value from
kmem_cache_alloc() was freed using kfree(). Fix it to use the proper
kmem_cache_free() instead.
Fixes: d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr")
Signed-off-by: Xidong Wang <wangxidong_97@163.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180404093824.9313-1-chris@chris-wilson.co.uk
(cherry picked from commit 6be1187dbf)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
When cancelling the requests and clearing out the ports following a
successful preemption completion, also clear the active flag. I had
assumed that all preemptions would be followed by an immediate dequeue
(preserving the active user flag), but under rare circumstances we may
be triggering a preemption for the second port only for it to have
completed before the preemotion kicks in; leaving execlists->active set
even though the system is now idle.
We can clear the flag inside the common execlists_cancel_port_requests()
as the other users also expect the semantics of active being cleared.
Fixes: f6322eddaf ("drm/i915/preemption: Allow preemption between submission ports")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180324125829.27026-1-chris@chris-wilson.co.uk
(cherry picked from commit eed7ec52f2)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Pull wait_var_event updates from Ingo Molnar:
"This introduces the new wait_var_event() API, which is a more flexible
waiting primitive than wait_on_atomic_t().
All wait_on_atomic_t() users are migrated over to the new API and
wait_on_atomic_t() is removed. The migration fixes one bug and should
result in no functional changes for the other usecases"
* 'sched-wait-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/wait: Improve __var_waitqueue() code generation
sched/wait: Remove the wait_on_atomic_t() API
sched/wait, arch/mips: Fix and convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/ocfs2: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/nfs: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/fscache: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/btrfs: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/afs: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, drivers/media: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, drivers/drm: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait: Introduce wait_var_event()
Add drm_format_mod update, which is omitted.
Fixes: e546e281("drm/i915/gvt: Dmabuf support for GVT-g")
Cc: stable@vger.kernel.org
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Much error exist in host dmesg during guest boot up with loca display
enabled.
gvt: vgpu 1: invalid range gmadr 0x0 size 0x0
This error happens when qemu get dmabuf info in case that the virtual
display plane is enabled but its base address is an invalid 0, such
case may be true before guest enable its plane. At this moment, its
state is copied from host where the plane may be enabled.
This patch disable primary/sprite/cursor plane at virtual display
initialization, so intel_vgpu_decode_primary/cursor/sprite could
return early as plane is disabled, then plane base check is skipped and
error message disapper.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Much error message exist in host dmesg when guest boot up with local
display enabled.
[ 167.680011] gvt: vgpu 1: invalid range gmadr 0x0 size 0x0
[ 167.680013] gvt: vgpu 1: invalid gma address: 0
The second error line duplicate with the first error line, so this
patch remove this redundant error message and make the next error
message much clearer.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
We have canceled dma map for ppgtt entries. Also we need to do it for
ggtt entries when them are invalidated.
This can fix task hung issue as:
[13517.791767] INFO: task gvt_service_thr:1081 blocked for more than 120 seconds.
[13517.792584] Not tainted 4.14.15+ #3
[13517.793417] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[13517.794267] gvt_service_thr D 0 1081 2 0x80000000
[13517.795132] Call Trace:
[13517.795996] ? __schedule+0x493/0x77b
[13517.796859] schedule+0x79/0x82
[13517.797740] schedule_preempt_disabled+0x5/0x6
[13517.798614] __mutex_lock.isra.0+0x2b5/0x445
[13517.799504] ? __switch_to_asm+0x24/0x60
[13517.800381] ? intel_gvt_cleanup+0x10/0x10
[13517.801261] ? intel_gvt_schedule+0x19/0x2b9
[13517.802107] intel_gvt_schedule+0x19/0x2b9
[13517.802954] ? intel_gvt_cleanup+0x10/0x10
[13517.803824] gvt_service_thread+0xe3/0x10d
[13517.804704] ? wait_woken+0x68/0x68
[13517.805588] kthread+0x118/0x120
[13517.806478] ? kthread_create_on_node+0x3a/0x3a
[13517.807381] ? call_usermodehelper_exec_async+0x113/0x11a
[13517.808307] ret_from_fork+0x35/0x40
v3: split out ggtt reset case.
v2: also unmap ggtt during reset.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
GVT-g dispatches request to host i915 and depends on i915 notify
ring interrupt mechanism to check completion of request.
For now MI_USER_INTERRUPT in guest requests is passed through
in GVT-g cmd parser and i915 does not use it, which causes
unnecessary interrupt handling in i915.
On the other hand, if several requests from guest are combined into
one request in and contain MI_USER_INTERRUPT in the middle of
combined request. GVT-g still has to wait on the whole request to
complete to inject user interrupts to guest.
This patch makes all the MI_USER_INTERRUPT nop to save some interrupt
handling.
Here is test result to run glmark2 on guest for 10 seconds:
host master interrupts number is reduced from 16021 to 11162
host user interrupts number is reduced from 7936 to 3536
v2:
- revise commit message. (Kevin)
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1466154 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
- Display fixes for booting with MST hub lid closed and display
freezing after hibernation (fd.o bugs 105470 & 105196)
- Fix for a very rare interrupt handling race resulting in GPU hang
* tag 'drm-intel-next-fixes-2018-03-27' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix hibernation with ACPI S0 target state
drm/i915/execlists: Use a locked clear_bit() for synchronisation with interrupt
drm/i915: Specify which engines to reset following semaphore/event lockups
drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
After
commit dd9f31c7a3
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Aug 16 17:46:07 2017 +0300
drm/i915/gen9+: Set same power state before hibernation image
save/restore
during hibernation/suspend the power domain functionality got disabled,
after which resume could leave it incorrectly disabled if the ACPI
target state was S0 during suspend and i915 was not loaded by the loader
kernel.
This was caused by not considering if we resumed from hibernation as the
condition for power domains reiniting.
Fix this by simply tracking if we suspended power domains during system
suspend and reinit power domains accordingly during resume. This will
result in reiniting power domains always when resuming from hibernation,
regardless of the platform and whether or not i915 is loaded by the
loader kernel.
The reason we didn't catch this earlier is that the enabled/disabled
state of power domains during PMSG_FREEZE/PMSG_QUIESCE is platform
and kernel config dependent: on my SKL the target state is S4
during PMSG_FREEZE and (with the driver loaded in the loader kernel)
S0 during PMSG_QUIESCE. On the reporter's machine it's S0 during
PMSG_FREEZE but (contrary to this) power domains are not initialized
during PMSG_QUIESCE since i915 is not loaded in the loader kernel, or
it's loaded but without the DMC firmware being available.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105196
Reported-and-tested-by: amn-bas@hotmail.com
Fixes: dd9f31c7a3 ("drm/i915/gen9+: Set same power state before hibernation image save/restore")
Cc: amn-bas@hotmail.com
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322143642.26883-1-imre.deak@intel.com
(cherry picked from commit 0f90603c33)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We were relying on the uncached reads when processing the CSB to provide
ourselves with the serialisation with the interrupt handler (so we could
detect new interrupts in the middle of processing the old one). However,
in commit 767a983ab2 ("drm/i915/execlists: Read the context-status HEAD
from the HWSP") those uncached reads were eliminated (on one path at
least) and along with them our serialisation. The result is that we
would very rarely miss notification of a new interrupt and leave a
context-switch unprocessed, hanging the GPU.
Fixes: 767a983ab2 ("drm/i915/execlists: Read the context-status HEAD from the HWSP")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321091027.21034-1-chris@chris-wilson.co.uk
(cherry picked from commit 9153e6b7c8)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If the GPU is stuck waiting for an event or for a semaphore, we need to
reset the GPU in order to recover. We have to tell the reset routine
which engines we want reset, but we were still using the old interface
and declaring it as "not-fatal".
Fixes: 14b730fcb8 ("drm/i915/tdr: Prepare error handler to accept mask of hung engines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-1-chris@chris-wilson.co.uk
(cherry picked from commit ca98317b89)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a10 ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit ad260ab32a)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This patch fixes spelling typos found in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
GVT regression fix that caused guest VM GPU hang.
Fix for race conditions in declaring GPU wedged (hit in CI).
* tag 'drm-intel-next-fixes-2018-03-22' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/gvt: force to set all context control bits from guest
drm/i915/gvt: Update PDPs after a vGPU mm object is pinned.
drm/i915/gvt: Invalidate vGPU PPGTT mm objects during a vGPU reset.
drm/i915/kvmgt: Handle kzalloc failure
drm/i915/gvt: fix spelling mistake: "destoried" -> "destroyed"
drm/i915/gvt: Remove reduntant printing of untracked mmio
drm/i915/pmu: Work around compiler warnings on some kernel configs
drm/i915: Only call tasklet_kill() on the first prepare_reset
drm/i915: Wrap engine->schedule in RCU locks for set-wedge protection
drm/i915/icl: do not save DDI A/E sharing bit for ICL
On unknown/unhandled ioctls the driver should return an error, so
userspace knows it tried to use something unsupported.
Cc: stable@vger.kernel.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
If the GPU is stuck waiting for an event or for a semaphore, we need to
reset the GPU in order to recover. We have to tell the reset routine
which engines we want reset, but we were still using the old interface
and declaring it as "not-fatal".
Fixes: 14b730fcb8 ("drm/i915/tdr: Prepare error handler to accept mask of hung engines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-1-chris@chris-wilson.co.uk
(cherry picked from commit ca98317b89)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The old wait_on_atomic_t() is going to get removed, use the more
flexible wait_var_event() API instead.
Unlike wake_up_atomic_t(), wake_up_var() will issue the wakeup
even if the variable is not 0.
No change in functionality.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a10 ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit ad260ab32a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Our shadow context content is from guest but with masked control reg like
CTX_CONTEXT_CONTROL, we need to make sure all settings from guest would be set
when this context is on hw, this trys to force mask enable bits for all to
ensure every bits setting would be effective on hw.
One regression found related to once inhibit bit is set, gpu engine are working
on inhibit state until MI_LOAD_REG_IMM command or context image clear inhibit
bit with mask bit set to 1, and val bit set to 0. In gvt-g currently workload
has the highest priority, so gvt-g workload could trigger preempt context
easily, preempt context set inhibit bit, then gvt-g workload is scheduled in,
but gvt-g workload shadow context image usually doesn't set inhibit mask bit,
so gpu is still in inhibit state when gvt workload is running. This caused gpu
hang.
Suggested-by: Zhang, Xiong <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Zhang, Xiong <xiong.y.zhang@intel.com>
The PDPs of a shadow page will only be valid after a vGPU mm is pinned.
So the PDPs in the shadow context should be updated then.
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
As different OSes might handling GVT PPGTT creation/destroy notification
differently during a vGPU reset. A better approach is invalidating all
vGPU PPGTT mm objects during vGPU reset.
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Trivial fix to spelling mistake in gvt_err error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reduntant message prints when:
- linux guest creating.
- dma-buf win10 guest boot.
- xonotic stress testing in linux guest.
Add below registers to default MMIO handler:
0xd00, RPM_CONFIG0
0xd40, RC6_LOCATION
0x65010, HSW_AUD_MISC_CTRL
0x6671c,
0x700a0, CUR_FBC_CTL
0x7239c,
v2:
- Should init i915_reg_t using uint32_t instead of _MMIO macro.
(compiling errors)
- Use defined offset in i915_reg.h
(zhenyu)
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Arnd Bergman reports:
"""
The conditional spinlock confuses gcc into thinking the 'flags' value
might contain uninitialized data:
drivers/gpu/drm/i915/i915_pmu.c: In function '__i915_pmu_event_read':
arch/x86/include/asm/paravirt_types.h:573:3: error: 'flags' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is correct, but it's easy to see how the compiler gets confused
here. This avoids the problem by pulling the lock outside of the function
into its only caller.
"""
On deeper look it seems this is caused by paravirt spinlocks
implementation when CONFIG_PARAVIRT_DEBUG is set, which by being
complicated, manages to convince gcc locked parameter can be changed
externally (impossible).
Work around it by removing the conditional locking parameters altogether.
(It was never the most elegant code anyway.)
Slight penalty we now pay is an additional irqsave spin lock/unlock cycle
on the event enable path. But since enable is not a fast path, that is
preferrable to the alternative solution which was doing MMIO under irqsave
spinlock.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1fe699e301 ("drm/i915/pmu: Fix sleep under atomic in RC6 readout")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080535.17490-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit ad055fb8e0)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
tasklet_kill() will spin waiting for the current tasklet to be executed.
However, if tasklet_disable() has been called, then the tasklet is never
executed but permanently put back onto the runlist until
tasklet_enable() is called. Ergo, we cannot use tasklet_kill() inside a
disable/enable pair. This is the case when we call set-wedge from inside
i915_reset(), and another request was submitted to us concurrent to the
reset.
Fixes: 963ddd63c3 ("drm/i915: Suspend submission tasklets around wedging")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-6-chris@chris-wilson.co.uk
(cherry picked from commit 68ad361285)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Similar to the staging around handling of engine->submit_request, we
need to stop adding to the execlists->queue prior to calling
engine->cancel_requests. cancel_requests will move requests from the
queue onto the timeline, so if we add a request onto the queue after that
point, it will be lost.
Fixes: af7a8ffad9 ("drm/i915: Use rcu instead of stop_machine in set_wedged")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-5-chris@chris-wilson.co.uk
(cherry picked from commit 47650db02d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We don't want to preserve the DDI A 4 lane bit on ICL.
Fixes: 3d2011cfa4 ("drm/i915/icl: remove port A/E lane sharing limitation.")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306104155.3526-1-jani.nikula@intel.com
(cherry picked from commit 1e6aa7e55c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
drm_printk is used for both DRM_ERROR and DRM_DEBUG with unnecessary
arguments that can be removed by creating separate functins.
Create specific functions for these calls to reduce x86/64 defconfig
size by ~20k.
Modify the existing macros to use the specific calls.
new:
$ size -t drivers/gpu/drm/built-in.a | tail -1
1876562 44542 995 1922099 1d5433 (TOTALS)
old:
$ size -t drivers/gpu/drm/built-in.a | tail -1
1897565 44542 995 1943102 1da63e (TOTALS)
Miscellanea:
o intel_display requires a change to use the specific calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/016b5cb84cede20fd0f91ed6965421d99fd5f2ce.1520978414.git.joe@perches.com
José Roberto de Souza