This patch enables QAM Annex-B support (US digital cable)
for the s5h1409 VSB/QAM demodulator.
Tested successfully with the mt2131 tuner,
present on the following supported boards:
Hauppauge WinTV-HVR-1250
Hauppauge WinTV-HVR-1800
Hauppauge WinTV-HVR-1800lp
This patch is also known to work with an upcoming XC5000 tuner driver.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a pointer to the (recently posted) Cafe data sheet.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the system is suspended while the camera is streaming, it will not
continue streaming on resume. Save the state properly so that resume
works.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The V4L1 spec says that the image size should be with with VIDIOCSWIN before
requesting buffers with VIDIOCGMBUF and capturing into them with
VIDIOCMCAPTURE.
But it seems that many apps don't do this. They set the size using the fields
in the VIDIOCMCAPTURE ioctl. The driver doesn't know what size to capture
until it actually starts to capture. In particular, it doesn't know what size
to capture until it has already mmap the captured buffers. Which is quite
stupid. Why V4L1 has size and format fields for VIDIOCMCAPTURE I have no idea.
Many drivers don't support this, including those using v4l1-compat.
The bttv does, which is probably the only reason such broken software is so
prevalent.
But, the driver doesn't adjust its idea of what size is being captured when it
is set this way. If you try to query the driver's current setting with
v4l2-ctl, it won't be correct.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bttv driver instists that the depth specified in the call to VIDIOCSPICT
match the pixel format specified in the same call.
vlc doesn't set the depth field, which makes the SPICT ioctl always fail.
The V4L1 standard is not clear on how most operation are supposed to work, and
this is no exception. The depth field would appear to be entirely redundant,
as the pixel format specifies a specific depth. It could be that this field
was only meant for output from the *G*PICT ioctl and should be ignored in
*S*PICT. This is in fact what the v4l1-compat wrapper does.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a system here that actively relies upon RTC wake alarms, and it
has been failing (again) for a few days when attempting to use the
/sys/class/rtc/rtc?/wakealarm interface.
The old (fixed by Linus) /proc/ interface still works, but I'd like to
get it using the new one.
This patch fixes rtc-cmos to ignore the two upper bits when reading the
BCD mday (day of month) register from CMOS. Some systems (eg. mine)
seem to have the top bit set to "1" for some reason.
The older /proc/ interface ignores the upper bits, and so we should too.
Signed-off-by: Mark Lord <mlord@pobox.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Torsten Kaiser wrote:
> Looking that calltrace upwards, it seems replacing the
> memset(dma->sglist,...) with sg_init_table(...) would fix the BUG_ON()
> as that inits the SG_MAGIC.
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
[BLOCK] Don't allow empty barriers to be passed down to queues that don't grok them
dm: bounce_pfn limit added
Deadline iosched: Fix batching fairness
Deadline iosched: Reset batch for ordered requests
Deadline iosched: Factor out finding latter reques
* 'sg' of git://git.kernel.dk/linux-2.6-block:
[SG] Get rid of __sg_mark_end()
cleanup asm/scatterlist.h includes
SG: Make sg_init_one() use general table init functions
By setting the request_limit in send_srp_login to 1 we allowed login
requests to be sent to the server adapter. If this was not an initial
login, but was a login after a disconnect with the server, other I/O
requests could attempt to be processed before the login occured. These
I/O requests would fail, sometimes resulting in filesystems getting
marked read-only.
To address this we can set the request_limit to 0 while doing the login
and add an exception where login requests, along with task management
events, are always passed to the server.
There is a case where the request_limit had already reached 0 would result
in all events being sent rather than returning SCSI_MLQUEUE_HOST_BUSY; this
has also been fixed by this patch.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch corrects the lpfc tag handling issue identified by Hannes Reinecke
http://marc.info/?l=linux-scsi@m=119270235628850&w=2
The basis for this patch originated from Hajime Kai. Thank You Hajime.
Signed-off-by: hajime-kai@soft.fujitsu.com
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's nothing to be gained by configuring downstream links faster
than the upstream link and such configurations cause problems on
certain PMPs. Limit downstream link speed by the upstream link speed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In sata_set_spd_needed(), if SControl read failed, it returned 0 and
skipped PHY speed configuration. However, if SControl access fails,
it's far more logical to request PHY speed configuration. Reverse the
logic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata EH used to ignore errors not associated with commands when
determining whether speed down is necessary or not. This leads to the
following problems.
* Errors not associated with commands can occur indefinitely without
libata EH taking corrective actions.
* Upstream link errors don't trigger speed down when PMP is attached
to it and commands issued to downstream device trigger errors on the
upstream link.
This patch makes ata_eh_link_autopsy() consider errors not associated
with command for speed down.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reset failure is a critical error. It results in disabling the link
requiring user intervention to re-enable it. Make reset failure
handling more robust such that libata EH doesn't give up too early.
* Temporary glitches during hardreset may lead to classification
failure when there's no softreset available. Retry instead of
giving up.
* Initial softreset or follow up softreset may fail classification.
Move classification error handling block out of followup softreset
block such that both cases are handled and retry instead of giving
up. Also, on the last try, give ATA class a blind shot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up and reorganize ata_eh_reset() to ease further changes.
* Cache ARRAY_SIZE(ata_eh_reset_timeouts) in @max_tries.
* Cache link->flags in @lflags.
* Move failure handling block to the end of the function and unnest
both success and failure handling blocks.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As jiffies changes asynchronously, it needs to be cached if unchanging
timestamp is needed. The code in ata_eh_reset() intended to do that
with @now but never actually did it. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commands sent to ATAPI tape drives via the SCSI generic (sg) driver are
limited in the amount of data that they can transfer by the max_sectors
value. The max_sectors value is currently calculated according to the
command set for disk drives, which doesn't apply to tape drives. The
default max_sectors value of 256 limits ATAPI tape drive commands to
128 KB. This patch against 2.6.24-rc1 increases the max_sectors value
for tape drives to 65535, which permits tape drive commands to transfer
just under 32 MB.
Tested with a SuperMicro PDSME motherboard, AHCI, and a Sony SDX-570V
SATA tape drive.
Note that some of the chipset drivers also set their own max_sectors
value, which may override the value set in libata-core. I don't have
any of these chipsets to test, so I didn't go messing with them. Also,
ATAPI devices other than tape drives may benefit from similar changes,
but I have only tape drives and disk drives to test.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original workaround for the Promise ASIC PRD bug
contained an endianess bug which I failed to detect:
the adjustment of the last PRD entry's length field
applied host arithmetic to little-endian data, which
is incorrect on big-endian machines.
We have the length available in host-endian format, so
do the adjustment on host-endian data and then convert
and store it in the PRD entry's little-endian data field.
Thanks to an anonymous reviewer for detecting this bug.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/libata-core.c:768: warning: 'ata_lpm_enable' defined but not used
drivers/ata/libata-core.c:784: warning: 'ata_lpm_disable' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded on-stack copy of FIS
in sata_fsl_cache_taskfile_from_d2h_fis().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCRs in the driver map to the standard values found in include/linux/ata.h,
so no need for individual scr_read/scr_write case statements duplicating
the natural value.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Jazz machines have to use the PIT timer for dyntick and highresolution
kernels. This may break because currently just like i386 used to do MIPS
uses two separate spinlocks in the actual PIT code and the PC speaker
code. So switch to do it the same that x86 currently does PIT locking.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: linux-input mailing list moved to vger.kernel.org
Input: inport, logibm - use KERN_INFO when reporting missing mouse
Input: appletouch - idle reset logic broke older Fountains
Input: hp_sdc.c - fix section mismatch
Input: appletouch - add Johannes Berg as maintainer
Input: Add Euro and Dollar key codes
Input: xpad - add more USB IDs
Some watchdog drivers initialize global spinlocks in module's init function
which is tolerable, but some do it in PCI probe function. So, switch to
static initialization to fix theoretical bugs and, more importantly, stop
giving people bad examples.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Device mapper uses its own bounce_pfn that may differ from one on underlying
device. In that way dm can build incorrect requests that contain sg elements
greater than underlying device is able to handle.
This is the cause of slab corruption in i2o layer, occurred on i386 arch when
very long direct IO requests are addressed to dm-over-i2o device.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Cc: <stable@kernel.org>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sg_mark_end() overwrites the page_link information, but all users want
__sg_mark_end() behaviour where we just set the end bit. That is the most
natural way to use the sg list, since you'll fill it in and then mark the
end point.
So change sg_mark_end() to only set the termination bit. Add a sg_magic
debug check as well, and clear a chain pointer if it is set.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Many mouse drivers are often compiled (e.g. in Linux distributions) into the
kernel at the same time just to make sure that at least one driver will suceed
in find it's mouse device. Nevertheless, only the inport and logitech busmouse
mouse drivers report with KERN_ERR log level if the mouse wasn't found. They
should use KERN_INFO instead, because it's not an error if the mouse isn't
attached at all.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fountains do not support change mode request and therefore
should be excluded from idle reset attempts.
Also:
- do not re-submit URB when we decide that touchpad needs to be
reinicialized
- do not repeat size detection when reinitializing the touchpad
- Add missing KERN_* prefixes to messages
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
When testing the myri10ge driver with 2.6.24-rc1, I found
that the machine crashed under heavy load:
Unable to handle kernel paging request at 0000000000100108 RIP:
[<ffffffff803cc8dd>] net_rx_action+0x11b/0x184
The address corresponds to the list_move_tail() in
netif_rx_complete():
if (unlikely(work == weight))
list_move_tail(&n->poll_list, list);
Eventually, I traced the crashes to calling netif_rx_complete() with
work_done == budget. From looking at other drivers, it appears that
one should only call netif_rx_complete() when work_done < budget.
To fix it, I changed the test in myri10ge_poll() so that it refers
to to work_done rather than looking at the rx ring status. If
work_done is < budget, then that implies we have no more packets to
process. Any races will be resolved by the NIC when the write to
irq_claim is made.
In myri10ge_clean_rx_done(), if we ever exceeded our budget, it would
report a work_done one larger than was acutally done. This is because
the increment was done in the conditional, so work_done would be
incremented regardless of whether or not the test passed or failed.
This would lead to the WARN_ON_ONCE(work > weight); warning in
net_rx_action triggering. I've moved the increment of work_done
inside the loop. Note that this would only be a problem when we had
exceeded our budget.
Signed off by: Andrew Gallatin <gallatin@myri.com>
Andrew Gallatin Myricom Inc
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver shouldn't complain if the register range is larger than what
it expects. This works around failures with some device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When not building an arch/powerpc kernel, the mpc5200 FEC driver depends
on some symbols which are not defined (BESTCOMM & BESTCOMM_FEC).
This patch flips around the dependancy logic so that it cannot be
selected unless BESTCOMM_FEC is selected first. Kconfig stops
complaining this way.
Also, the driver only works for arch/powerpc (not arch/ppc) anyway so
it should depend on PPC_MERGE also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the wait_tx routine to call cpu_relax() instead of udelay() to
reduce console output latency and test for the TXFULL bit instead of
TXEMPTY. That way the FIFO doesn't need to by 100% flushed before
writing the next character.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Finally, the zero_it argument can be completely removed from
the callers and from the function prototype.
Besides, fix the checkpatch.pl warnings about using the
assignments inside if-s.
This patch is rather big, and it is a part of the previous one.
I splitted it wishing to make the patches more readable. Hope
this particular split helped.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fcd239d3d5.
I messed up, ia64 still uses these files in the current tree, and now
can not build the pci code, which all ia64 boxes seem to require :)
This fixes that mistake.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes dead code spotted by the Intel C Compiler.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The ohci_enable() function shared between pci_probe and pci_resume
takes a host endian config rom, but ohci->config_rom is __be32. This
sets up the config rom in the wrong endian on little endian machine,
specifically, BusOptions will be initialized to a 0 max receive size.
This patch changes the way we reuse the config rom so that we avoid
this problem.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix:
WARNING: at arch/arm/mach-pxa/clock.c:69 clk_disable()
[<c002d7c8>] (dump_stack+0x0/0x14) from [<c00334f4>] (clk_disable+0x34/0xa0)
[<c00334c0>] (clk_disable+0x0/0xa0) from [<c028a43c>] (pxamci_set_ios+0x74/0xf0)
[<c028a3c8>] (pxamci_set_ios+0x0/0xf0) from [<c0281548>] (mmc_power_off+0x90/0x9c)
[<c02814b8>] (mmc_power_off+0x0/0x9c) from [<c0281a30>] (mmc_start_host+0x18/0x28)
[<c0281a18>] (mmc_start_host+0x0/0x28) from [<c02825a0>] (mmc_add_host+0xe8/0x104)
[<c02824b8>] (mmc_add_host+0x0/0x104) from [<c028a7d0>] (pxamci_probe+0x24c/0x2f4)
[<c028a584>] (pxamci_probe+0x0/0x2f4) from [<c01e5948>] (platform_drv_probe+0x20/0x24)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
CC drivers/scsi/arm/powertec.o
In file included from drivers/scsi/arm/powertec.c:29:
drivers/scsi/arm/scsi.h: In function 'next_SCp':
drivers/scsi/arm/scsi.h:42: error: 'struct scatterlist' has no member named 'page'
drivers/scsi/arm/scsi.h: In function 'init_SCp':
drivers/scsi/arm/scsi.h:80: error: 'struct scatterlist' has no member named 'page'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is referenced both from __devinit code (ivtv_probe) and
normal .text (ivtv_process_eeprom), and therefore cannot
be discarded via __devexit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hidinput_connect() ignores retval from input_register_device(). Fix it
by properly undoing all the registrations that have been already done,
and return error.
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
drivers/hid/usbhid/hiddev.c: In function 'hiddev_compat_ioctl':
drivers/hid/usbhid/hiddev.c:746: warning: passing argument 4 of 'hiddev_ioctl' makes
integer from pointer without a cast
Add cast to hiddev_compat_ioctl()
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
add SubmittingPatches to Documentation/ja_JP
fix typo in SubmittingPatches
Driver Core: fix bug in device_rename() for SYSFS_DEPRECATED=y
sysfs: make sysfs_{get,put}_active() static
kobject: check for duplicate names in kobject_rename
Driver core: remove class_device_*_bin_file
This should fix the sysfs warnings that renaming network devices is
causing to show up with CONFIG_SYSFS_DEPRECATED=y
The code just shouldn't run if class devices are real directories, it's
an update for the symlink in the class directory. Nobody noticed that as
long as the creation of sysfs files silently failed, and we both missed
it before the merge, because we don't run SYSFS_DEPRECATED=y.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: David Miller <davem@davemloft.net>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These functions are not used by anyone, so remove them from the tree.
The class_device code will be removed soon anyway, so no future users
will ever be possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove a spurious call to kfree_skb() in the connector rx_skb handler.
This fixes a regression introduced by the '[NET]: make netlink user ->
kernel interface synchronious' patch (cd40b7d398)
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/fmr_pool: Stop ib_fmr threads from contributing to load average
IB/ipath: Fix incorrect use of sizeof on msg buffer (function argument)
IB/ipath: Limit length checksummed in eeprom
IB/ipath: Fix a race where s_last is updated without lock held
IB/mlx4: Lock SQ lock in mlx4_ib_post_send()
IPoIB/cm: Fix receive QP cleanup
I noticed my machine was at a constant load average of 1. This was
because ib_create_fmr_pool calls kthread_create but does not
immediately wake the thread up.
Change to using kthread_run so we enter ib_fmr_cleanup_thread(), set
TASK_INTERRUPTIBLE, then go to sleep.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
ixgb: fix TX hangs under heavy load
e1000e: Fix typo ! &
ixgbe: minor sparse fixes
e1000: sparse warnings fixes
ixgb: fix sparse warnings
e1000e: fix sparse warnings
mv643xx_eth: Fix MV643XX_ETH offsets used by Pegasos 2
Blackfin EMAC driver: Fix Ethernet communication bug (dupliated and lost packets)
DM9601: Support for ADMtek ADM8515 NIC
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement and use ATA_QCFLAG_QUIET
libata: stop being overjealous about non-IO commands
libata: flush is an IO command
sata_promise: cleanups
sata_promise: ASIC PRD table bug workaround, take 2
A merge error occurred where we merged the wrong block here
in version 1.0.120. The right condition for frags is slightly
different then for the skb, so account for the difference properly
and trim the TSO based size right.
Originally part of a fix reported by IBM to fix TSO hangs on
pSeries hardware.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make strings const if possible, and fix includes so forward definitions
are seen.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix sparse warnings and problems from e1000 driver.
Added a sparse fix for the module param array index
-- Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix sparse warnings in ixgb driver for net-2.6.24.
Added a sparse fix for invalid declaration using non-constant value
in ixgb_set_multi. Added a fix for the module param array index
and allows int params in the array. --Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix sparse warnings from e1000e driver in net-2.6.24.
Added a sparse fix for module param arrays which can have int values
but only the array index needs to be unsigned. --Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix Ethernet communication bug(dupliated and lost packets)
in RMII PHY mode- dont call mac_disable and mac_enable during
10/100 REFCLK changes - mac_enable screws up the DMA descriptor chain
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add device ID for the ADMtek ADM8515 USB NIC to the DM9601 driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Inside a function declared as
void foo(char bar[512])
the value of sizeof bar is the size of a pointer, not 512. So avoid
constructions like this by passing the size explicitly.
Also reduce the size of the buffer to 128 bytes (512 was overly generous).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The small eeprom that holds the GUID etc. contains a data-length, but if
the actual eeprom is new or has been erased, that byte will be 0xFF,
which is greater than the maximum physical length of the eeprom, and
more importantly greater than the length of the buffer we vmalloc'd.
Sanity-check the length to avoid the possbility of reading past end of
buffer.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a small window where a send work queue entry could be
overwritten by ib_post_send() because s_last is updated before the
entry is read.
This patch closes the window by acquiring the lock and updating
the last send work queue entry index after reading the wr_id.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Because of a typo, mlx4_ib_post_send() takes the same lock rq.lock as
mlx4_ib_post_recv(). Correct the code so the intended sq.lock is
taken when posting a send.
Noticed by Yossi Leybovitch and pointed out by Jack Morgenstein from
Mellanox.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[TIPC]: Add tipc_config.h to include/linux/Kbuild.
[WAN]: lmc_ioctl: don't return with locks held
[SUNRPC]: fix rpc debugging
[TCP]: Saner thash_entries default with much memory.
[SUNRPC] rpc_rdma: we need to cast u64 to unsigned long long for printing
[IPv4] SNMP: Refer correct memory location to display ICMP out-going statistics
[NET]: Fix error reporting in sys_socketpair().
[NETFILTER]: nf_ct_alloc_hashtable(): use __GFP_NOWARN
[NET]: Fix race between poll_napi() and net_rx_action()
[TCP] MD5: Remove some more unnecessary casting.
[TCP] vegas: Fix a bug in disabling slow start by gamma parameter.
[IPVS]: use proper timeout instead of fixed value
[IPV6] NDISC: Fix setting base_reachable_time_ms variable.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 97d97224ff ("[SERIAL] Fix
console initialisation ordering"), serial_core calls ->pm() on
initialization even if the port was used for console.
This behaviour breaks serial_txx9 console since The serial_txx9 driver
initialize its port entirely on its ->pm() method if new state was 0.
This patch adds checking for oldstate value to fix this probelm.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No reason I can think of of making them default y Most people don't have
the hardware and with default y they just pollute lots of configs during
make oldconfig.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: "Nelson, Shannon" <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove warning from powerpc ppc64_defconfig builds:
drivers/video/aty/radeon_pm.c:30: warning: 'radeon_reinitialize_M10' declared 'static' but never defined
It's used only under CONFIG_PM, and only with CONFIG_X86 before it is
defined, so the forward declaration can be moved under the ifdef.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix FB_OMAP dependencies so that the OMAP FB driver options are presented
correctly.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement ATA_QCFLAG_QUIET which indicates that there's no need to
report if the command fails with AC_ERR_DEV and set it for passthrough
commands.
Combined with previous changes, this now makes device errors for all
direct commands reported directly to the issuer without going through
EH actions and reporting.
Note that EH is still invoked after non-IO device errors to determine
the nature of the error and resume command execution (some controller
requires special care after error to continue). It just performs
default maintenance after error, examines what's going on, realizes
that it's none of its business and reports the command failure without
logging any error messages.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata EH always revalidated device and retried failed command after
error except for ATAPI CCs. This is unnecessary and hinders with
users issuing direct commands. This patch makes the following
changes.
* Make sata_sil24 not request ATA_EH_REVALIDATE on device errors.
sil24 is the only driver which does this. All others let libata EH
core code decide.
* Don't request revalidation after device error of non-IO command.
Revalidation doesn't really help anybody. As ATA_EH_REVALIDATE
isn't set by default, there's no reason to clear it after sense data
is read. Kill ATA_EH_REVALIDATE clearing code while at it.
* Don't retry non-IO command after device error. Device has rejected
the command. There's no point in retrying.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_QCFLAG_IO is used to mark commands which are used to perform
regluar IO transfers via block layer. These commands are assumed to
be valid and taken more seriously during error handling. Cache flush
is used by regular IO path and necessary for data integrity. Mark it
with ATA_QCFLAG_IO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Second-generation Promise SATA controllers have an ASIC bug
which can trigger if the last PRD entry is larger than 164 bytes,
resulting in intermittent errors and possible data corruption.
Work around this by replacing calls to ata_qc_prep() with a
private version that fills the PRD, checks the size of the
last entry, and if necessary splits it to avoid the bug.
Also reduce sg_tablesize by 1 to accommodate the new entry.
Tested on the second-generation SATA300 TX4 and SATA300 TX2plus,
and the first-generation PDC20378.
Thanks to Alexander Sabourenkov for verifying the bug by
studying the vendor driver, and for writing the initial patch
upon which this one is based.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
Changes since previous version:
* use new PDC_MAX_PRD constant to initialise sg_tablesize
drivers/ata/sata_promise.c | 87 ++++++++++++++++++++++++++++++++++++++++++---
1 files changed, 83 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(akpm: it's doing copy_to_user() inside spin_lock_irqsave(): this driver
appears to be beyond help).
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (26 commits)
cpuidle: remove unused exports
acpi: remove double mention of Support for ACPI option
ACPI: use select POWER_SUPPLY for AC, BATTERY and SBS
ACPI: Battery: Allow extract string from integer
ACPI: battery: Support for non-spec name for LiIon technology
ACPI: battery: register power_supply subdevice only when battery is present
suspend: MAINTAINERS update
ACPI: update MAINTAINERS
fujitsu-laptop.c: remove dead code
cpuidle: unexport tick_nohz_get_sleep_length
ACPI: battery: Update battery information upon sysfs read.
fujitsu-laptop: make 2 functions static
ACPI: EC: fix use-after-free
ACPI: battery: remove dead code
ACPI: Fan: Drop force_power_state acpi_device option
ACPI: Fan: fan device does not need own structure
ACPI: power: don't cache power resource state
ACPI: EC: Output changes to operational mode
ACPI: EC: Add workaround for "optimized" controllers
ACPI: EC: Don't re-enable GPE for each transaction.
...
The uevent API has changed from 2.6.22 and this patch eliminates
annoying compiler errors
Signed off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch renames the IOMMU config option to GART_IOMMU because in fact it
means the GART and not general support for an IOMMU on x86.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch renames the include file asm-x86/iommu.h to asm-x86/gart.h to make
clear to which IOMMU implementation it belongs. The patch also adds "GART" to
the Kconfig line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the following unused exports:
- cpuidle_devices
- cpuidle_register_governor
- cpuidle_unregister_governor
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Current description for CONFIG_ACPI includes the word "Support" twice. One
effect of this is that in menuconfig the "--->" that indicates the presence
of sub-options will not show up unless you have a very wide console.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
POWER_SUPPLY is needed for AC, battery, and SBS sysfs support. Use
'select' instead of 'depends on', as it is will not be selected by anything
else, leading to confusion.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Some machines return integer instead of expected string.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
Support Li-Ion as possible name for technology.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure no power_supply object is present unless we actualy detect
presence of battery. This fixes ghost batteries detected by HAL
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'alpm' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: add hw link power management support
[libata] Link power management infrastructure
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: fix newly introduced host-reset bug
[libata] sata_nv: fix SWNCQ enabling
libata: add MAXTOR 7V300F0/VA111900 to NCQ blacklist
libata: no need to speed down if already at PIO0
libata: relocate forcing PIO0 on reset
pata_ns87415: define SUPERIO_IDE_MAX_RETRIES
[libata] Address some checkpatch-spotted issues
[libata] fix 'if(' and similar areas that lack whitespace
libata: implement ata_wait_after_reset()
libata: track SLEEP state and issue SRST to wake it up
libata: relocate and fix post-command processing
This patch will set the correct bits to turn on Aggressive
Link Power Management (ALPM) for the ahci driver. This
will cause the controller and disk to negotiate a lower
power state for the link when there is no activity (see
the AHCI 1.x spec for details). This feature is mutually
exclusive with Hot Plug, so when ALPM is enabled, Hot Plug
is disabled. ALPM will be enabled by default, but it is
settable via the scsi host syfs interface. Possible
settings for this feature are:
Setting Effect
----------------------------------------------------------
min_power ALPM is enabled, and link set to enter
lowest power state (SLUMBER) when idle
Hot plug not allowed.
max_performance ALPM is disabled, Hot Plug is allowed
medium_power ALPM is enabled, and link set to enter
second lowest power state (PARTIAL) when
idle. Hot plug not allowed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
compat_ioctl: fix block device compat ioctl regression
[BLOCK] Fix bad sharing of tag busy list on queues with shared tag maps
Fix a build error when BLOCK=n
block: use lock bitops for the tag map.
cciss: update copyright notices
cfq_get_queue: fix possible NULL pointer access
blk_sync_queue() should cancel request_queue->unplug_work
cfq_exit_queue() should cancel cfq_data->unplug_work
block layer: remove a unused argument of drive_stat_acct()
* 'sg' of git://git.kernel.dk/linux-2.6-block:
Correction of "Update drivers to use sg helpers" patch for IMXMMC driver
sg_init_table() should use unsigned loop index variable
sg_last() should use unsigned loop index variable
Initialise scatter/gather list in sg driver
Initialise scatter/gather list in ata_sg_setup
x86: fix pci-gart failure handling
SG: s390-scsi: missing size parameter in zfcp_address_to_sg()
SG: clear termination bit in sg_chain()
The recent fix to host reset introduced a problem, whereby AHCI-enable
bit would be cleared upon reset, if it was not asserted prior to reset.
Unconditionally enable AHCI-enable bit.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a) for type B we should _not_ iounmap() acb->pmu; it's not ioremapped.
b) for type B we should iounmap() two regions we _do_ ioremap.
c) if ioremap() fails, we need to bail out (and clean up).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use of ptrdiff_t in places like
- if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len))
+ if (!access_ok(VERIFY_WRITE, (u8 __user *)
+ (ptrdiff_t) u_tmp->rx_buf,
+ u_tmp->len))
is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general
we are not even promised that ptrdiff_t is large enough to hold a pointer,
just enough to hold a difference between two pointers within the same object).
For another, it confuses the fsck out of sparse.
Use unsigned long or uintptr_t instead. There are several places misusing
ptrdiff_t; fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
initializing a field in data shared with the card with
cpu_to_le32(something) | 0x100000 is broken - the field is, indeed,
little-endian and we need cpu_to_le32() on both parts.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
driver still has serious portability problems
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- off by one in dmar_get_fault_reason() (maximal index in array is
ARRAY_SIZE()-1, not ARRAY_SIZE())
- NULL noise removal
- __iomem annotation fix
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't undef __i386__/__x86_64__ in uml anymore, make sure that (few) places
that required adjusting the ifdefs got those.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates the copyright information for the cciss driver. It
includes extending the year to 2007 (how timely) and some minor corrections
deemed necessary by HP legal and the Open Source Review Board. Please
consider this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
--------------------------------------------------------------------------------
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
MAXTOR 7V300F0/VA111900 does spurious NCQ completions. Add it to
blacklist. This problem is reported by Carsten Otto.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carsten Otto <c-otto@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After reset, transfer mode is always PIO0 regardless of
dev->xfer_mask. Check dev->pio_mode before trying to slow down after
configuration failure. This prevents bogus speed down before device
is actually configured.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a
bit out of place as it should be applied to all resets - hard, soft
and implementation which don't use ata_bus_softreset(). Relocate it
such that...
* For new EH, it's done in ata_eh_reset() before calling prereset.
* For old EH, it's done before calling ap->ops->phy_reset() in
ata_bus_probe().
This makes PIO0 forced after all resets. Another difference is that
reset itself is done after PIO0 is forced.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code copied from drivers/ide/pci/ns87415.c uses this, so copy the
definition from there as well.
Fixes the following build error:
CC [M] drivers/ata/pata_ns87415.o
drivers/ata/pata_ns87415.c: In function ‘ns87560_read_buggy’:
drivers/ata/pata_ns87415.c:228: error: ‘SUPERIO_IDE_MAX_RETRIES’ undeclared (first use in this function)
drivers/ata/pata_ns87415.c:228: error: (Each undeclared identifier is reported only once
drivers/ata/pata_ns87415.c:228: error: for each function it appears in.)
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some commands need post-processing after successful completion. This
was done in ata_scsi_qc_complete() till now but this has the following
problems.
* Post-command processing gets executed when qc is completed from EH.
Some qc's are retried from EH with zero err_mask and thus triggers
unnecessary/incorrect post-command processing.
* Command post processing doesn't belong to SAT layer.
* Link-wide revalidation was scheduled where device revalidation
suffices.
This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used. While at it,
restructure code a bit for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for ethernet on mpc5200/mpc5200b SoCs (FEC).
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
eHEA resources that are allocated via H_CALLs have a unique identifier each.
These identifiers are necessary to free the resources. A reboot notifier
is used to free all eHEA resources before the indentifiers get lost, i.e
before kexec starts a new kernel.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The legacy jumbo frame receive code is no longer needed since all
hardware can do packet split and we're no longer offering a bypass
kernel config option to disable packet split. Remove the unused code.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround code performed software stripping instead of the
hardware which can do it much faster. None of the e1000e target
hardware has issues with this feature and should work fine. This
gives us some performance back on receive, and removes some
kludging stripping the 4 bytes.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Upon inspection the rx FIFO size calculation code was found to have
2 significant flaws: A superfluous minus sign resulting in the
wrong size to be used for jumbo frames on 82573 and ich9, as well
as that this code rewrote the read-only adapter->pba variable
resulting in different values at each run.
Without this patch jumbo's will work but performance will be
awkward since the TX size is not adequate for two whole frames.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix allocation and freeing of jumbo frames where several bugs
were recently introduced by cleanups after we forked this code
from e1000. This moves ps_pages to buffer_info where it really
belongs and makes it a dynamically allocated array. The penalty
is not that high since it's allocated outside of the buffer_info
struct anyway.
Without this patch all jumbo frames are completely broken and the
driver panics.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
interrupt handlers return a return value these days.
Also, kill always-true test and unneeded void* cast.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* change #warning to a code comment
* add comment and special ifdef'd 64-bit code for a situation where
we must store a pointer into a CAPI field 'Data', which is fixed by
the interface at 32 bits.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Karsten Keil <kkeil@suse.de>
After turning on DEBUG_SG I hit a fail:
kernel BUG at include/linux/scatterlist.h:50!
sg_build_indirect
sg_build_reserve
sg_open
chrdev_open
__dentry_open
do_filp_open
do_sys_open
We should initialise the sg list when we allocate it in sg_build_sgat.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
After turning on DEBUG_SG I hit a fail:
kernel BUG at include/linux/scatterlist.h:50!
ata_qc_issue
ata_scsi_translate
ipr_queuecommand
scsi_dispatch_cmd
scsi_request_fn
elv_insert
blk_execute_rq_nowait
blk_execute_rq
sg_io
scsi_cmd_ioctl
cdrom_ioctl
sr_block_ioctl
blkdev_driver_ioctl
blkdev_ioctl
block_ioctl
do_ioctl
vfs_ioctl
sys_ioctl
sg_ioctl_trans
It looks like ata_sg_setup is working on an uninitialised sg table. Call
sg_init_table to initialise it before use.
Signed-off-by: Anton Blanchard <anton@samba.org>
Note: this patch will fix it, but you could also get away with just
doing the sg_init_table() once at qc creation time.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix for the error below while linking vmlinux:
[...]
drivers/built-in.o: In function `ipg_ioctl':
drivers/net/ipg.c:2148: undefined reference to `generic_mii_ioctl'
drivers/built-in.o: In function `ipg_get_settings':
drivers/net/ipg.c:2181: undefined reference to `mii_ethtool_gset'
drivers/built-in.o: In function `ipg_set_settings':
drivers/net/ipg.c:2193: undefined reference to `mii_ethtool_sset'
drivers/built-in.o: In function `ipg_nway_reset':
drivers/net/ipg.c:2205: undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Avuton Olrich <avuton@gmail.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Disabling napi polling early is well enough.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Don't call napi_disable if not configured and make sure that any
misuse of napi_xxx in future fails with a compile error.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
(pointer > 0) is deeply weird; (pointer >= 0) is even dumber...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
#include <scatterlist/scatterlist.h>
is an odd thing to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct device doesn't have ->dma; it's in struct expansion_card where
that struct device is embedded into.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hp_sdc_exit() mustn't be __exit since it's called from the
__init hp_sdc_register().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Willem Riede <osst@riede.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc_spi: Fix mmc-over-spi regression
mmc: use common byte swap macros
mmc: fix cid and csd byte order
at91_mci: Fix bad reference
Patch 49dce689ad changed the sysfs data
structures for SPI in a way which broke the MMC-over-SPI host driver.
This patch fixes that regression by changing the scheme used to keep
from knowingly trying to use a shared bus segment, and updates the
adjacent comments slightly to better explain the issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMC over SPI sends the CID and CSD registers as data, not responses,
which means that the host driver won't do the necessary byte flipping
for us.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes the errors made in the users of the crypto layer during
the sg_init_table conversion. It also adds a few conversions that were
missing altogether.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not safe to to place struct pernet_operations in a special section.
We need struct pernet_operations to last until we call unregister_pernet_subsys.
Which doesn't happen until module unload.
So marking struct pernet_operations is a disaster for modules in two ways.
- We discard it before we call the exit method it points to.
- Because I keep struct pernet_operations on a linked list discarding
it for compiled in code removes elements in the middle of a linked
list and does horrible things for linked insert.
So this looks safe assuming __exit_refok is not discarded
for modules.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1b524963 ("IPoIB/cm: Use common CQ for CM send completions")
changed how the high-order bits of work request IDs were used, which
had the effect that IPOIB_CM_RX_DRAIN_WRID was no longer handled as a
connected mode receive completion. This leads to the messages
ib1: cm send completion event with wrid 1073741823 (> 64)
ib1: RX drain timing out
when an interface with connected mode QPs is brought down. Fix this
by making sure that both IPOIB_OP_CM and IPOIB_OP_RECV are set in
IPOIB_CM_RX_DRAIN_WRID.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
From the report by Nick Warne.
Tested-by: Nick Warne <nick@ukfsn.org>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* We shouldn't bother with dev->current_state, the PCI API functions we
call manage this for us (and do a far better job at it too).
* Remove pci_set_power_state(dev, PCI_D0) call in resume, as
pci_enable_device() does the same thing.
* Check pci_enable_device() return value. If it failed, fail
the entire resume and avoid programming timings into the [potentially
dead/asleep] chip.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that generic IDE PCI host driver is also affected by the same issue:
On Thursday 25 October 2007, Ralf Baechle wrote:
> CC drivers/ide/pci/generic.o
> drivers/ide/pci/generic.c:52: error: __setup_str_ide_generic_all_on causes a
> +section type conflict
[ Also reported by Martijn Uffing <mp3project@sarijopen.student.utwente.nl>. ]
This patch workarounds the problem in a bit hackish way but without
removing const from generic_chipsets[] (it adds const to __setup() so
__setup_str_ide_generic_all becomes const).
Now all __{dev}initdata data in generic IDE PCI host driver are read-only
so it builds again (driver's .init.data section gets marked as READONLY).
Cc: Martijn Uffing <mp3project@sarijopen.student.utwente.nl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that hpt366 host driver is also affected by the same issue:
> drivers/ide/pci/hpt366.c:1428: error: hpt366_chipsets causes a section type
> conflict
This patch workarounds the problem by making static struct hpt_info instances
const. Now all __devinitdata data in hpt366 host driver are read-only so it
builds again (driver's .init.data section gets marked as READONLY).
While at it:
* Bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently.
This patch workarounds the problem by removing __devinitdata tag from 'primary'
variable (which makes 'primary' to be moved from .init.data to .bss section).
Now all __devinitdata data in cy82c693 host driver are read-only so it builds
again (driver's .init.data section gets marked as READONLY).
While at it:
* Move 'primary' variable to its only user, init_iops_cy82c693().
* Bump driver version.
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch fix the follwing for 3945:
1. Fix direct scan by make sure we set one_direct_scan only when the
mac80211 ask for direct scan.
2. Fix mac_stop and mac_remove_interface calles, we make sure we cancel any
scan and disassoc on these call
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following for 3945:
1. Make sure we cancel scan if RXON command is called.
2. Call scan abort on scan watchdog.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following problems for 4965:
1. Fix direct scan by make sure we set one_direct_scan only when the
mac80211 ask for direct scan.
2. Fix mac_stop and mac_remove_interface calles, we make sure we cancel any
scan and disassoc on these call.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix the following:
1. make sure we are not scanning before we call REPLY_RXON
2. set RXON_FILTER_ASSOC_MSK only after we receive association response
3. call scan abort on scan watchdog instead of restart
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removeis TSF flag from probe request. TSF should be added only to
probe response.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows rtl8187 to receive multicast frames if requested.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV4]: Explicitly call fib_get_table() in fib_frontend.c
[NET]: Use BUILD_BUG_ON in net/core/flowi.c
[NET]: Remove in-code externs for some functions from net/core/dev.c
[NET]: Don't declare extern variables in net/core/sysctl_net_core.c
[TCP]: Remove unneeded implicit type cast when calling tcp_minshall_update()
[NET]: Treat the sign of the result of skb_headroom() consistently
[9P]: Fix missing unlock before return in p9_mux_poll_start
[PKT_SCHED]: Fix sch_prio.c build with CONFIG_NETDEVICES_MULTIQUEUE
[IPV4] ip_gre: sendto/recvfrom NBMA address
[SCTP]: Consolidate sctp_ulpq_renege_xxx functions
[NETLINK]: Fix ACK processing after netlink_dump_start
[VLAN]: MAINTAINERS update
[DCCP]: Implement SIOCINQ/FIONREAD
[NET]: Validate device addr prior to interface-up
* 'sg' of git://git.kernel.dk/linux-2.6-block:
fix sg_phys to use dma_addr_t
ub: add sg_init_table for sense and read capacity commands
x86: pci-gart fix
blackfin: fix sg fallout
xtensa: dma-mapping.h is using linux/scatterlist.h functions, so include it
SG: audit of drivers that use blk_rq_map_sg()
arch/um/drivers/ubd_kern.c: fix a building error
SG: Change sg_set_page() to take length and offset argument
AVR32: Fix sg_page breakage
mmc: sg fallout
m68k: sg fallout
More SG build fixes
sg: add missing sg_init_table calls to zfcp
SG build fix
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest:
lguest: documentation update
lguest: Add to maintainers file.
lguest: build fix
lguest: clean up lguest_launcher.h
lguest: remove unused "wake" element from struct lguest
lguest: use defines from x86 headers instead of magic numbers
lguest: example launcher header cleanup.
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] sata_nv: SWNCQ should not apply to MCP61
libata-core: Be a bit more relaxed about early DMA zero devices
ahci: ahci: implement workaround for ASUS P5W-DH Deluxe ahci_broken_hardreset(), take #2
Fix pata_icside build for recent libata API changes
libata: cosmetic clean up in ata_eh_reset()
libata-core.c: make 2 functions static
[libata] Create internal helper ata_dev_set_feature()
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[netdrvr] forcedeth: add MCP77 device IDs
rndis_host: reduce MTU instead of refusing to talk to devices with low max packet size
cpmac: update to new fixed phy driver interface
cpmac: convert to napi_struct interface
cpmac: use print_mac() instead of MAC_FMT
natsemi: fix oops, link back netdevice from private-struct
ehea: fix port_napi_disable/enable
bonding/bond_main.c: fix cut'n'paste error
make bonding/bond_main.c:bond_deinit() static
drivers/net/ipg.c: cleanups
remove Documentation/networking/net-modules.txt
This fixes some totally illogical and wrong code that converts things to
and from BCD mode essentially randomly, does math on values in BCD mode
etc etc. Introduce a few helper functions to make it a bit more obvious
what is going on, and make sure that we always do all the arithmetic
(and anythign else, for that matter) in binary, not BCD.
Tested by Mark Lord, who found the problem originally, and also pushed
the patch back and reminded me about it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes dead code spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_fujitsu_{add,remove}() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes a use-after-free introduced by
commit 30c08574da
(ACPI: EC: Add new query handler to list head)
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
After commit f1d4661abe this was dead
code.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
force_power_state was used as a workaround for invalid cached
power state of the device. We do not cache power state, so no need for
workaround.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI may change power resource state behind our back, so don't
keep our local copy, which may not be valid.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Insert printk() for every change in operational mode.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Some controllers do not send interrupts for OBF=1 event, but send
them for IBF=0. Add workaround for them.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=8459
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
With the auto selection of operation mode, absence of GPEs does not
really degrade performance, so let PM code to handle
enabling/disabling GPEs.
This is a revert of 5d57a6a55e,
which was meant to be temporary.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=7977
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Start in POLL mode, and if we receive confirmation GPE,
switch to INT mode.
If confirmations are not sent, switch back to POLL.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is no interrupt after last read according to spec, so
don't set bit that we are expecting one.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Number of flags is about to be increased, so it is better to
put them all into bits.
No functional changes.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Input layer should know about initial state of lid switch,
even before first notify.
Reference: https://bugzilla.novell.com/show_bug.cgi?id=326814
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_leave_sleep_state() should have correct list of wake and
runtime GPEs, which is available only after disable_wakeup_device()
is called.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 9b03933080 removed
acpi_gpe_sleep_prepare(), the only function used at S5 transition
Add call to generic acpi_enable_wake_device().
Reference: https://bugzilla.novell.com/show_bug.cgi?id=299882
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
this driver has a possible use after free due to a race when disconnect
and open handle intfdata without a lock.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
again, possible use after free due to touching intfdata without lock.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the driver sets intfdata to NULL without lock. Data structures can be
freed and accessed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove various newly-introduced compiler warnings for OHCI.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of pointless pci_set_mwi() compiler warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: usbserial - fix potential deadlock between write() and IRQ
usb_serial_generic_write() doesn't disable interrupts when taking port->lock,
and could therefore deadlock with usb_serial_generic_read_bulk_callback()
being called from interrupt, taking the same lock. Fix it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the IO Data Device USB-RSAQ5, PL2303 based
USB-serial converter, to pl2303 driver
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the disconnect method of this driver set intfdata to NULL before
removing attribute files. The attributes' read methods will happily
follow the NULL pointer. Here's the correct ordering.
Signed-off-by : Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete caused me to lock at buggy drivers in this respect. The idmouse has
a race between open and disconnect. This patch
- solves the open/disconnect race
- switches locking to mutexes
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1005) fixes a rather subtle problem. When
usb_set_configuration() registers the interfaces and their files in
sysfs, it doesn't expect those files to exist already. But when an
interface is registered, its driver may call usb_set_interface() and
thereby cause the sysfs files to be created. The result is an error
when usb_set_configuration() goes on to create those same files again.
The (not-so-great) solution is to have usb_set_configuration() remove
any existing files before creating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix ssb_ohci_probe() build bug:
drivers/built-in.o: In function `ssb_ohci_probe':
ohci-hcd.c:(.text+0xbff39): undefined reference to `ssb_device_enable'
ohci-hcd.c:(.text+0xbff6f): undefined reference to `ssb_admatch_base'
ohci-hcd.c:(.text+0xbff8b): undefined reference to `ssb_admatch_size'
ohci-hcd.c:(.text+0xbffe5): undefined reference to `ssb_device_disable'
[...]
the reason was that this Kconfig combination was allowed:
CONFIG_SSB=m
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_SSB=y
the fix is to require a modular USB_OHCI_HCD build when SSB is modular.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker spotted that we have already oops'ed if "dev"
was NULL in these places.
Since "dev" being NULL isn't possible at these places this patch removes
the NULL checks.
Additionally, I've fixed the formatting of the if's.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker spotted that we have already oops'ed if "dev"
was NULL.
Since "dev" being NULL doesn't seem to be possible here this patch
removes the NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
URB_FREE_BUFFER needs to be allowed in the sanity checks to use drivers that
use that flag.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ISD200 driver imports a single trivial routine from the IDE layer and
in doing so creates a mess of dependancies that drag in the entire old
IDE layer. Even more sad - it does this for a routine which is usually
(little endian) a null function!
- Copy the function into ISD200
- Rename it so it doesn't clash with the ide header prototype
- Remove all the depend constraints
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FTDI Elan driver: Convert the semaphore ftdi->u132_lock to the mutex
API
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1003) changes uhci-hcd to treat the URB_ISO_ASAP flag
the same as other host controller drivers, namely, to schedule an Iso
URB for the first available time slot that hasn't already expired.
URBs in which the flag isn't set will be scheduled for the first slot
following the last URB, even if it has expired.
This fixes a problem reported by Martin Bachem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: line over 80 characters
#23: FILE: drivers/usb/serial/ftdi_sio.c:297:
+ speed_t force_baud; /* if non-zero, force the baud rate to this value */
ERROR: use tabs not spaces
#31: FILE: drivers/usb/serial/ftdi_sio.c:881:
+^I$
ERROR: use tabs not spaces
#39: FILE: drivers/usb/serial/ftdi_sio.c:890:
+^I$
WARNING: line over 80 characters
#111: FILE: drivers/usb/serial/ftdi_sio.c:1956:
+ tty_encode_baud_rate(port->tty, priv->force_baud, priv->force_baud);
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No hardware termios setting in this case so keep the old settings
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the devices that have no hardware settings set up the termios return
properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Clear unsupported CMSPAR bit
- Clean up long chains of a->b-> a bit
- Encode baud rate back into tty structure properly
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Clean up paranoia checks
- Propogate back a correct fixed termios
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The empeg is pretty fixed. Tidy up the long foo->bar->baz stuff and
encode the fixed speed properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Expand some x&y to x & y so I could read it when checking
- Clear CMSPAR bit in the termios (as the driver does not support it)
- Encode the speed using the new tty_encode_baud_rate facility
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ch341 currently doesn't support most of the hardware setting. So to keep
the termios data right we propogate the old termios hardware values back then
encode the speed.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Set the i/ospeed in the initial termios properly
- Use the tty_encode_baud_rate functions to report resulting rates properly
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Earlier patches have removed the checking for old v new differences from the
USB drivers so we can now pass in a valid blank old termios so that we don't
to fill the drivers with magic hacks for console support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes two returns in the TI Davinci and
PNX4008 in void functions.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch makes the host RNDIS driver talk to RNDIS devices with an MTU
less than 1.5k, instead of refusing to talk to such a device.
Signed-Off-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
--
Hi Jeff,
are you the right person to send this to?
Nobody else seems to be wanting to forward this to Linus...
Thanks,
Tom
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use fixed_mdio_get_phydev for obtaining fixed phy instances and adopt to
changed fixed phy device naming.
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert cpmac to new napi_struct API introduced by
bea3348eef [NET]: Make NAPI polling independent
of struct net_device objects.
Only disable rx interrupts if napi actually has been scheduled.
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Switch to using DECLARE_MAC_BUF/print_mac() added by commit
0795af5729 [NET]: Introduce and use print_mac()
and DECLARE_MAC_BUF().
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Andrew Nelless <andrew@nelless.net> wrote:
> Hi,
>
> I booted up 2.6.24-rc1 this morning [Real early over a brew ;-)] and
> was having a problems with multiple ~5 second hangs on SATA/drive init
> (Something to do with "EH" something-or-other and resets but I'll
> email in separately about it later unless its fixed by the time I get
> the chance).
>
> Anyway, I went to fire up netconsole to get a decent log dump and hit
> across the following nasty. Netconsole works fine in 2.6.23.1 with a
> similar config and the same kernel parameters.
>
> A shot of the screen is the only method I could come up with to
> capture the log, I hope that is OK, it is pretty readable.
>
>
> The nasty:
> http://andotnet.nfshost.com/linux/2.6.24-rc1-netconsole-nullderef.jpg
the NULL dereference is here:
(gdb) list *0xffffffff804a9504
0xffffffff804a9504 is in natsemi_poll (drivers/net/natsemi.c:717).
712 return count;
713 }
714
715 static inline void __iomem *ns_ioaddr(struct net_device *dev)
716 {
717 return (void __iomem *) dev->base_addr;
718 }
719
which is this code from natsemi.c:
2227 struct net_device *dev = np->dev;
2228 void __iomem * ioaddr = ns_ioaddr(dev);
2229 int work_done = 0;
seems like the NAPI changes in -rc1 added an np->dev field but forgot to
initialize it ...
does the patch below fix the oops for you?
Ingo
-------------------->
Subject: natsemi: fix oops, link back netdevice from private-struct
From: Ingo Molnar <mingo@elte.hu>
this commit:
commit bea3348eef
Author: Stephen Hemminger <shemminger@linux-foundation.org>
Date: Wed Oct 3 16:41:36 2007 -0700
[NET]: Make NAPI polling independent of struct net_device objects.
added np->dev to drivers/net/natsemi.c's struct netdev_private, but
forgot to initialize that new field upon driver init. The result was
a predictable NULL dereference oops the first time the hardware
generated an interrupt.
Reported-by: Andrew Nelless <andrew@nelless.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
napi_disable / napi_enable must be applied on all ehea queues.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following cleanups:
- make ipg_nic_get_stats() static
- move DefaultPhyParam[] from ipg.h to ipg.c and make it static
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I guess Windows didn't care about the command so neither did they
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
P5W-DH Deluxe has ICH9 which doesn't have PMP support but SIMG 4726
hardwired to the second port of AHCI controller at PCI device 1f.2.
The 4726 doesn't work as PMP but as a storage processor which can do
hardware RAID on downstream ports.
When no device is attached to the downstream port of the 4726, pseudo
ATA device for configuration appears. Unfortunately, ATA emulation on
the device is very lousy and causes long hang during boot.
This patch implements workaround for the board. If the mainboard is
P5W-DH Deluxe (matched using DMI), only hardreset is used on the
second port of AHCI controller @ 1f.2 and the hardreset doesn't depend
on receiving the first FIS and just proceed to IDENTIFY.
This workaround fixes bugzilla #8923.
http://bugzilla.kernel.org/show_bug.cgi?id=8923
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Local variable @action usage in ata_eh_reset() is a bit confusing.
It's used only to cache ehc->i.action to test reset masks after
clearing it; however, due to the generic name "action", it's easy to
misinterpret the local variable as containing the selected reset
method later. Also, the reason for caching the original value is easy
to miss.
This patch renames @action to @tmp_action and make it buffer newly
selected value instead to improve readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Went through the documentation doing typo and content fixes. This
patch contains only comment and whitespace changes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
drivers/isdn/sc/shmem.c: In function 'memcpy_toshmem':
drivers/isdn/sc/shmem.c:54: warning: passing argument 1 of 'memcpy_toio' makes pointer from integer without a cast
Also, remove some unneeded braces, and add some useful whitespace.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do a full scan of the directory to try and be a bit more proactive,
instead of waiting for things to break.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some are already declared in include/linux/netdevice.h, while
some others (xfrm ones) need to be declared.
The driver/net/rrunner.c just uses same extern as well, so
cleanup it also.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'irq-upstream' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
[SPARC, XEN, NET/CXGB3] use irq_handler_t where appropriate
drivers/char/riscom8: clean up irq handling
isdn/sc: irq handler clean
isdn/act2000: fix major bug. clean irq handler.
char/pcmcia/synclink_cs: trim trailing whitespace
drivers/char/ip2: separate polling and irq-driven work entry points
drivers/char/ip2: split out irq core logic into separate function
[NETDRVR] lib82596, netxen: delete pointless tests from irq handler
Eliminate pointless casts from void* in a few driver irq handlers.
[PARPORT] Remove unused 'irq' argument from parport irq functions
[PARPORT] Kill useful 'irq' arg from parport_{generic_irq,ieee1284_interrupt}
[PARPORT] Consolidate code copies into a single generic irq handler
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (39 commits)
Remove Andrew Morton from list of net driver maintainers.
bonding: Acquire correct locks in alb for promisc change
bonding: Convert more locks to _bh, acquire rtnl, for new locking
bonding: Convert locks to _bh, rework alb locking for new locking
bonding: Convert miimon to new locking
bonding: Convert balance-rr transmit to new locking
Convert bonding timers to workqueues
Update MAINTAINERS to reflect my (jgarzik's) current efforts.
pasemi_mac: fix typo
defxx.c: dfx_bus_init() is __devexit not __devinit
s390 MAINTAINERS
remove header_ops bug in qeth driver
sky2: crash on remove
MIPSnet: Delete all the useless debugging printks.
AR7 ethernet: small post-merge cleanups and fixes
mv643xx_eth: Hook up mv643xx_get_sset_count
mv643xx_eth: Remove obsolete checksum offload comment
mv643xx_eth: Merge drivers/net/mv643xx_eth.h into mv643xx_eth.c
mv643xx_eth: Remove unused register defines
mv643xx_eth: Clean up mv643xx_eth.h
...
Set bits 0, 4, 5 and 7 of PCI configuration register 0x40 in the
quirk. This has the following effects and is recommended by the
vendor.
* Force enable of IDE channels (used to be left alone as BIOS
configured)
* Change initial phase behavior of PIO cycle such that the host pulls
down the bus instead of tristating it. Vendor recommends this
setting.
The above settings are better for the current generation of
controllers and needed for the upcoming next generation.
Tested on JMB363.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Another one doing spurious NCQ completions. Blacklist it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Steven Toth
