For TI power management chip TPS40422, READ_TEMPERATURE_2 command is supported on
page 1 of the chip, but the original driver(pmbus.c) only tried to detect this command
on page 0, this will lead to a result that the temperature sensor in page 1 couldn't
be detected. This change is to isolate the tps40422 driver from pmbus.c into a solo
front-end driver.
Signed-off-by: Zhu Laiwen <richard.zhu@nsn.com>
[Guenter Roeck: Dropped unnecessary license text (fixes checkpatch warning)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The FSF mailing address can and will change over time,
so drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Not all supported chips support the entire I2C address range.
Only accept specific chips at the addresses supported by that chip.
Check for invalid values in conversion rate and status registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Move g760a_driver to proper place to avoid forward declaration.
Also move g760a_id table close to g760a_driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
smatch complains as follows when checking w83791d.c.
drivers/hwmon/w83791d.c:996 store_temp23() warn:
'32768' 32768 can't fit into 32767 'data->temp_add[nr][index]'
Fix by using DIV_ROUND_CLOSEST and clamp_val to convert the values.
While we are at it, modify other macros as well for consistency and
to make the code easier to understand.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
smatch complains as follows when checking lm63.c.
drivers/hwmon/lm63.c:594 set_temp11() warn:
'65504' 65504 can't fit into 32767 'data->temp11[nr]'
drivers/hwmon/lm63.c:596 set_temp11() warn:
'32768' 32768 can't fit into 32767 'data->temp11[nr]'
Fix by using DIV_ROUND_CLOSEST and clamp_val to convert the values.
While we are at it, modify other macros as well for consistency and
to make the code easier to understand.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Move ad7418_driver to proper place to avoid forward declaration.
Also move ad7418_init_client() close to ad7418_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor B57330V2103 from EPCOS.
Signed-off-by: Johannes Pointner <johannes.pointner@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add missing i2c_set_clientdata() call in tmp103_probe, this makes the
dev_get_drvdata() call in tmp103_suspend/tmp103_resume return correct
address.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder functions to avoid forward declaration.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups.
This simplifies the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This simplifies the code a bit and also ensures the attribute groups are
properly removed from sysfs when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for Lattice's POWR1220 power manager IC. Read
access to all the ADCs on the chip are supported through the hwmon
sysfs files.
Signed-off-by: Scott Kanowitz <skanowitz@echo360.com>
[Guenter Roeck: Removed some extra ( )]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip.
Clamp the input values to the supported limits first to fix the problem.
For set_temp_hyst:
As Guenter pointed out that the temperature is read as unsigned and stored in
an unsigned long. This is wrong; nothing in the datasheet suggests that the
value (the absolute temperature) must be positive.
So change it to signed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ensure mutex lock protects the read-modify-write period to prevent possible
race condition bug.
In additional, update data->valid should also be protected by the mutex lock.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.
Cc: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Temperature limit register writes did not account for negative numbers.
As a result, writing -127000 resulted in -126000 written into the
temperature limit register. This problem affected temp[1-3]_min,
temp[1-3]_max, temp[1-3]_auto_temp_crit, and temp[1-3]_auto_temp_min.
When writing pwm[1-3]_freq, a long variable was auto-converted into an int
without range check. Wiring values larger than MAXINT resulted in unexpected
register values.
When writing temp[1-3]_auto_temp_max, an unsigned long variable was
auto-converted into an int without range check. Writing values larger than
MAXINT resulted in unexpected register values.
vrm is an u8, so the written value needs to be limited to [0, 255].
Cc: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current code uses channel as array index, so the valid channel value is
0 .. ADS1015_CHANNELS - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Temperature limit clamps are applied after converting the temperature
from milli-degrees C to degrees C, so either the clamp limit needs
to be specified in degrees C, not milli-degrees C, or clamping must
happen before converting to degrees C. Use the latter method to avoid
overflows.
vrm is an u8, so the written value needs to be limited to [0, 255].
Cc: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Using the wall clock time for delta time calculations is wrong to
begin with because wall clock time can be set from userspace and NTP.
Such data wants to be based on clock monotonic.
The calculations also are done on a nanosecond basis. Use the
nanoseconds based interface right away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <jdelvare@suse.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Temperature limit registers are signed. Limits therefore need
to be clamped to (-128, 127) degrees C and not to (0, 255)
degrees C.
Without this fix, writing a limit of 128 degrees C sets the
actual limit to -128 degrees C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Dashes are not allowed in hwmon name attributes.
Use "da9055" instead of "da9055-hwmon".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Dashes are not allowed in hwmon name attributes.
Use "da9052" instead of "da9052-hwmon".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into input registers doesn't make sense, even more so since
the writes actually ended up writing into the maximum limit registers.
Drop it.
Cc: stable@vger.kernel.org
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is customary to clamp limits instead of bailing out with an error
if a configured limit is out of the range supported by the driver.
This simplifies limit configuration, since the user will not typically
know chip and/or driver specific limits.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Upper limit for write operations to temperature limit registers
was clamped to a fractional value. However, limit registers do
not support fractional values. As a result, upper limits of 127.5
degrees C or higher resulted in a rounded limit of 128 degrees C.
Since limit registers are signed, this was stored as -128 degrees C.
Clamp limits to (-55, +127) degrees C to solve the problem.
Value on writes to auto_temp[12]_min and auto_temp[12]_max were not
clamped at all, but masked. As a result, out-of-range writes resulted
in a more or less arbitrary limit. Clamp those attributes to (0, 127)
degrees C for more predictable results.
Cc: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The module test script for the adm1021 driver exposes a cache problem
when writing temperature limits. temp_min and temp_max are expected
to be stored in milli-degrees C but are stored in degrees C.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing to fanX_div does not clear the cache. As a result, reading
from fanX_div may return the old value for up to two seconds
after writing a new value.
This patch ensures the fan_div cache is updated in set_fan_div().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
temp2_input should not be writable, fix it.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, dev_info() at the end of the probe says
"type:%s ". But, prints pdev->name.
This patch uses "pdev_id->name" which prints the thermistor type.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since commit 648cd48c9e
The hwmon name attributes must not include '-' so the name must be
rename from gpio-fan to gpio_fan
Signed-off-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In commit 4cab259f, the emc1403 driver was converted to use regmap but the
necessary Kconfig option was not added.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Murata Manufacturing Co., Ltd is the vendor for
NTC (Negative Temperature coefficient) based Thermistors.
But, the driver extensively uses "NTC" as the vendor name.
This patch corrects the vendor name also updates the
compatibility strings according to the vendor-prefix.txt
Note: Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current code is buggy, it shows the current fan speed as minimum fan speed.
Fix up show_fan_reg macro to correctly report fan and fan_min speed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups instead of
the old-style manual attributes and hwmon device registration.
Also, unroll the attribute group macros for better code
readability.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Move atxp1_id and atxp1_driver to proper place to avoid forward declaration.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Sensirion SHTC1 and compatible temperature and humidity
sensors.
Signed-off-by: Tomas Pop <tomas.pop@sensirion.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Per Dalén <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Generic detection leads to too many false positives, so drop it. FWIW
sensors-detect does not have such generic detection. If the user wants
to force the driver to bind to a not yet supported chip, he/she can
still do so using sysfs attribute new_device.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All devices supported by ina2xx are bidirectional and report the
measured shunt voltage and power values as a signed 16 bit, but the
current driver implementation caches all registers as u16, leading
to an incorrect sign extension when reporting to userspace in
ina2xx_get_value().
This patch fixes the problem by casting the signed registers to s16.
Tested on an INA219.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New chip support to existing drivers:
Add support for STTS2004 and AT30TSE004 to jc42 driver
Add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
Document hwmon kernel API
Convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421,
and tmp102 drivers to use new hwmon API functions
Replace function macros in lm80, lm92, and jc42 drivers with
real code
Convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
Various additional cleanup and minor bug fixes in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dytt
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging into next
Pull hwmon updates from Guenter Roeck:
"New driver for NCT6683D
New chip support to existing drivers:
- add support for STTS2004 and AT30TSE004 to jc42 driver
- add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
- document hwmon kernel API
- convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421, and
tmp102 drivers to use new hwmon API functions
- replace function macros in lm80, lm92, and jc42 drivers with real
code
- convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
- various additional cleanup and minor bug fixes in several drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (60 commits)
hwmon: (nct6775) Fix probe unwind paths to properly unregister platform devices
hwmon: (nct6683) Fix probe unwind paths to properly unregister platform devices
hwmon: (ultra45_env) Introduce managed version of kzalloc
hwmon: Driver for NCT6683D
hwmon: (lm80) Rearrange code to avoid forward declarations
hwmon: (lm80) Convert fan display function macros into functions
hwmon: (lm80) Convert voltage display function macros into functions
hwmon: (lm80) Convert temperature display function macros into functions
hwmon: (lm80) Normalize all temperature values to 16 bit
hwmon: (lm80) Simplify TEMP_FROM_REG
hwmon: (lm83) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm83) Rearange code to avoid forward declarations
hwmon: (lm83) Drop FSF address
hwmon: (max1619) Convert to use devm_hwmon_device_register_with_groups
hwmon: (max1619) Drop function macros
hwmon: (max1619) Rearrange code to avoid forward declarations
hwmon: (max1619) Drop FSF address
hwmon: (max1619) Fix critical alarm display
hwmon: (jc42) Add support for STTS2004 and AT30TSE004
hwmon: (jc42) Convert function macros into functions
...
Cleanups for 3.16. Among these are:
- A bunch of misc cleanups for Broadcom platforms, mostly housekeeping
- Enabling Common Clock Framework on the older s3c24xx Samsung chipsets
- Cleanup of the Versatile Express system controller code, moving it to syscon
- Power management cleanups for OMAP platforms
+ a handful of other cleanups across the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wuX4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC cleanups from Olof Johansson:
"Cleanups for 3.16. Among these are:
- a bunch of misc cleanups for Broadcom platforms, mostly
housekeeping
- enabling Common Clock Framework on the older s3c24xx Samsung
chipsets
- cleanup of the Versatile Express system controller code, moving it
to syscon
- power management cleanups for OMAP platforms
plus a handful of other cleanups across the place"
* tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
ARM: kconfig: allow PCI support to be selected with ARCH_MULTIPLATFORM
clk: samsung: fix build error
ARM: vexpress: refine dependencies for new code
clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares __initdata
cpufreq: exynos: Fix the compile error
ARM: S3C24XX: move debug-macro.S into the common space
ARM: S3C24XX: use generic DEBUG_UART_PHY/_VIRT in debug macro
ARM: S3C24XX: trim down debug uart handling
ARM: compressed/head.S: remove s3c24xx special case
ARM: EXYNOS: Remove unnecessary inclusion of cpu.h
ARM: EXYNOS: Migrate Exynos specific macros from plat to mach
ARM: EXYNOS: Remove exynos_subsys registration
ARM: EXYNOS: Remove duplicate lines in Makefile
ARM: EXYNOS: use v7_exit_coherency_flush macro for cache disabling
ARM: OMAP4: PRCM: remove references to cm-regbits-44xx.h from PRCM core files
ARM: OMAP3/4: PRM: add support of late_init call to prm_ll_ops
ARM: OMAP3/OMAP4: PRM: add prm_features flags and add IO wakeup under it
ARM: OMAP3/4: PRM: provide io chain reconfig function through irq setup
ARM: OMAP2+: PRM: remove unnecessary cpu_is_XXX calls from prm_init / exit
ARM: OMAP2+: PRCM: cleanup some header includes
...
The mapping from OF device IDs to platform device IDs is wrong.
TYPE_NCPXXWB473 is 0, TYPE_NCPXXWL333 is 1, so
ntc_thermistor_id[TYPE_NCPXXWB473] is { "ncp15wb473", TYPE_NCPXXWB473 }
while
ntc_thermistor_id[TYPE_NCPXXWL333] is { "ncp18wb473", TYPE_NCPXXWB473 }.
So the name is wrong for all but the "ntc,ncp15wb473" entry, and the
type is wrong for the "ntc,ncp15wl333" entry.
So map the entries by index, it is neither elegant nor robust but at
least it is correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
In commit 9e8269de, support was added for ntc_thermistor devices being
declared in the device tree and implemented on top of IIO. With that
change, a dependency was added to the ntc_thermistor driver:
depends on (!OF && !IIO) || (OF && IIO)
This construct has the drawback that the driver can no longer be
selected when OF is set and IIO isn't, nor when IIO is set and OF is
not. This is a regression for the original users of the driver.
As the new code depends on IIO and is useless without OF, include it
only if both are enabled, and set the dependencies accordingly. This
is clearer, more simple and more correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Call platform_device_unregister() rather than platform_device_put() to
unregister successfully registered platform devices.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Call platform_device_unregister() rather than platform_device_put() to
unregister successfully registered platform devices.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the unnecessary label out_free is removed.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert fan display function macros into functions to reduce
code size and improve code readability.
Code size reduction is about 200 bytes on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert voltage display function macros into functions to reduce
code size and improve code readability.
Code size reduction is about 600 bytes on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert temperature display function macros into functions to reduce
code size and improve code readability.
Code size reduction is about 2k on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TEMP_FROM_REG gets 12 bits of temperature data in the upper 12 bit
of a signed 16 bit parameter, with the integer part (including sign)
in the upper 8 bit and the remainder in bit 4..7. The lower 4 bit of
the 16 bit data is always 0. We can use that information to convert
the temperature directly into display data (1/1000th of degree C).
Note that the stored temperature data is not shifted right as the
comment claimed, so remove that misleading comment.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function macros make the code larger and difficult ro read.
Drop them and reduce code size (on x86_64) by ~1800 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Forward declarations are unnecessary and easy to avoid, so rearrange
code and drop them.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The overtemperature status bit, which is used to display critical alarm status,
matches the output of the OVERT signal 1:1. If that signal is active-low, the
bit will read 1 if there is no alarm. It is therefore necessary to reverse
the bit in this case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also fix links to datasheets for other supported sensors from
ST Microelectronics, and add links to several Atmel datasheets.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1412, EMC1413, and EMC1414 are fully compatible to EMC1402, EMC1403,
and EMC1404, and even report the same chip ID. Add to device ID table
to enable instantiation with correct chip names.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing the hysteresis limit returned -ERANGE if the written hysteresis
was too high or too low. Relax error check and adjust the hysteresis
value to its valid range.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips in this chip series only support a single hysteresis value. Having
multiple writable hysteresis attributes is therefore confusing, since a single
write affects all hysteresis temperatures. Make all but one (temp1_crit_hyst)
read-only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Alarm and fault status register on EMC1402, EMC1412, and EMC1422 is reported
in a different register than with other chips. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for emc1402/emc1412/emc1422 temperature monitoring chips.
This line of sensors only has 2 temperature channels (internal and external)
in comparison to the emc14x3 (3 channels) and emc14x4 (4 channels).
Signed-off-by: Josef Gajdusek <atx@atx.name>
[Guenter Roeck: ordered i2c address list, updated description/headline]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function macros obfuscate code and increase code size, so drop them.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function macros make the code harder to read and increase code size,
so drop them.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Updating the hysteresis value when updating the critical temperature limit
was following the rule of 'least surprise'. However, it had the undesirable
side effect of changing the hysteresis for all other attributes, which
defeats the purpose of least surprise. In addition, it could result in
invalid hysteresis values if the resulting hysteresis was too large. In such
cases the resulting hysteresis ended up changed anyway, which again defeats
the purpose. So drop that code and document the new behavior.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Forward declarations are easy to avoid and unnecessary.
Rearrange code to avoid it.
No functional change.
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The FSF mailing address changes over time, so drop it.
No functional change.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pointer to client->dev is used several times in the probe function.
Simplify code by introducing a separate variable for it.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Components of the Versatile Express platform (configuration
microcontrollers on motherboard and daughterboards in particular)
talk to each other over a custom configuration bus. They
provide miscellaneous functions (from clock generator control
to energy sensors) which are represented as platform devices
(and Device Tree nodes). The transactions on the bus can
be generated by different "bridges" in the system, some
of which are universal for the whole platform (for the price
of high transfer latencies), others restricted to a subsystem
(but much faster).
Until now drivers for such functions were using custom "func"
API, which is being replaced in this patch by regmap calls.
This required:
* a rework (and move to drivers/bus directory, as suggested
by Samuel and Arnd) of the config bus core, which is much
simpler now and uses device model infrastructure (class)
to keep track of the bridges; non-DT case (soon to be
retired anyway) is simply covered by a special device
registration function
* the new config-bus driver also takes over device population,
so there is no need for special matching table for
of_platform_populate nor "simple-bus" hack in the arm64
model dtsi file (relevant bindings documentation has
been updated); this allows all the vexpress devices
fit into normal device model, making it possible
to remove plenty of early inits and other hacks in
the near future
* adaptation of the syscfg bridge implementation in the
sysreg driver, again making it much simpler; there is
a special case of the "energy" function spanning two
registers, where they should be both defined in the tree
now, but backward compatibility is maintained in the code
* modification of the relevant drivers:
* hwmon - just a straight-forward API change
* power/reset driver - API change
* regulator - API change plus error handling
simplification
* osc clock driver - this one required larger rework
in order to turn in into a standard platform driver
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mike Turquette <mturquette@linaro.org>
The datasheet for EMC1413/EMC1414, which is fully compatible to
EMC1403/1404 and uses the same chip identification, references revision
numbers 0x01, 0x03, and 0x04. Accept the full range of revision numbers
from 0x01 to 0x04 to make sure none are missed.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 454aee17f claims to convert driver emc1403 to use
devm_hwmon_device_register_with_groups, however the patch itself makes
use of hwmon_device_register_with_groups instead. As the driver remove
function was still dropped, the hwmon device is no longer unregistered
on driver removal, leading to a resource leak.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 454aee17f hwmon: (emc1403) Convert to use devm_hwmon_device_register_with_groups
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org [3.13+]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Attempts to set the hysteresis value to a temperature below the target
limit fails with "write error: Numerical result out of range" due to
an inverted comparison.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit 9fb6c9c73b.
Tjmax on some Intel CPUs is below 85 degrees C. One known example is
L5630 with Tjmax of 71 degrees C. There are other Xeon processors with
Tjmax of 70 or 80 degrees C. Also, the Intel IA32 System Programming
document states that the temperature target is in bits 23:16 of MSR 0x1a2
(MSR_TEMPERATURE_TARGET), which is 8 bits, not 7.
So even if turbostat uses similar checks to validate Tjmax, there is no
evidence that the checks are actually required. On the contrary, the
checks are known to cause problems and therefore need to be removed.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75071.
Fixes: 9fb6c9c hwmon: (coretemp) Refine TjMax detection
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
An implementation error should not crash the kernel if it is avoidable.
Replace BUG() with WARN_ONCE().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'label' attribute was always created but returned -ENOENT
if there is no label and such behaviour is undefined from
libsensors' point of view.
Fixed by providing is_visible method in the attributes group,
so the attribute is not created at all when unnecessary.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver used to directly us a DT 'compatible' property for
the 'name' attribute of the hwmon devices. Unfortunately it
contains '-' which is illegal in this context. It messes up
libsensors and thus every application using it.
Fixed by providing equivalent (and simpler) name strings.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are a few more powerpc things for you.
So you'll find here the conversion of the two new firmware sysfs
interfaces to the new API for self-removing files that Greg and Tejun
introduced, so they can finally remove the old one.
I'm also reverting the hwmon driver for powernv. I shouldn't have
merged it, I got a bit carried away here. I hadn't realized it was
never CCed to the relevant maintainer(s) and list(s), and happens to
have some issues so I'm taking it out and it will come back via the
proper channels.
The rest is a bunch of LE fixes (argh, some of the new stuff was
broken on LE, I really need to start testing LE myself !) and various
random fixes here and there.
Finally one bit that's not strictly a fix, which is the HVC OPAL
change to "kick" the HVC thread when the firmware tells us there is
new incoming data. I don't feel like waiting for this one, it's
simple enough, and it makes a big difference in console responsiveness
which is good for my nerves"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (26 commits)
powerpc/powernv Adapt opal-elog and opal-dump to new sysfs_remove_file_self
Revert "powerpc/powernv: hwmon driver for power values, fan rpm and temperature"
power, sched: stop updating inside arch_update_cpu_topology() when nothing to be update
powerpc/le: Avoid creatng R_PPC64_TOCSAVE relocations for modules.
arch/powerpc: Use RCU_INIT_POINTER(x, NULL) in platforms/cell/spu_syscalls.c
powerpc/opal: Add missing include
powerpc: Convert last uses of __FUNCTION__ to __func__
powerpc: Add lq/stq emulation
powerpc/powernv: Add invalid OPAL call
powerpc/powernv: Add OPAL message log interface
powerpc/book3s: Fix mc_recoverable_range buffer overrun issue.
powerpc: Remove dead code in sycall entry
powerpc: Use of_node_init() for the fakenode in msi_bitmap.c
powerpc/mm: NUMA pte should be handled via slow path in get_user_pages_fast()
powerpc/powernv: Fix endian issues with sensor code
powerpc/powernv: Fix endian issues with OPAL async code
tty/hvc_opal: Kick the HVC thread on OPAL console events
powerpc/powernv: Add opal_notifier_unregister() and export to modules
powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early
powerpc/ppc64: Gracefully handle early interrupts
...
This reverts commit 0de7f8a917.
This driver wasn't merged via the proper maintainers (my fault ... ooops !)
and has serious issues so let's take it out for now and have a new better
one be merged the right way
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
Pull hwmon updates from Jean Delvare:
"This includes a number of driver conversions to
devm_hwmon_device_register_with_groups, a few cleanups, and
support for the ITE IT8623E"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Add support for IT8623E
hwmon: (it87) Fix IT8603E define name
hwmon: (lm90) Convert to use hwmon_device_register_with_groups
hwmon: (lm90) Create all sysfs groups in one call
hwmon: (lm90) Always use the dev variable in the probe function
hwmon: (lm90) Create most optional attributes with sysfs_create_group
hwmon: Avoid initializing the same field twice
hwmon: (pc87360) Avoid initializing the same field twice
hwmon: (lm80) Convert to use devm_hwmon_device_register_with_groups
hwmon: (adm1021) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Avoid initializing the same field twice
hwmon: (lm63) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Create all sysfs groups in one call
hwmon: (lm63) Introduce 'dev' variable to point to client->dev
hwmon: (lm63) Add additional sysfs group for temp2_type attribute
hwmon: (f71805f) Fix author's address
Add support for the IT8623E found on Asus motherboards. It has same
hardware monitoring block as IT8603E.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Zhu, Richard \(NSN - CN/Beijing\)