Intel Baytrail is based on Silvermont core so MSR_FSB_FREQ[2:0] == 0 means
that the CPU reference clock runs at 83.3MHz. Add this missing frequency to
the table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1392810750-18660-2-git-send-email-mika.westerberg@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If we cannot calibrate TSC via MSR based calibration
try_msr_calibrate_tsc() stores zero to fast_calibrate and returns that
to the caller. This value gets then propagated further to clockevents
code resulting division by zero oops like the one below:
divide error: 0000 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.13.0+ #47
task: ffff880075508000 ti: ffff880075506000 task.ti: ffff880075506000
RIP: 0010:[<ffffffff810aec14>] [<ffffffff810aec14>] clockevents_config.part.3+0x24/0xa0
RSP: 0000:ffff880075507e58 EFLAGS: 00010246
RAX: ffffffffffffffff RBX: ffff880079c0cd80 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffffffffff
RBP: ffff880075507e70 R08: 0000000000000001 R09: 00000000000000be
R10: 00000000000000bd R11: 0000000000000003 R12: 000000000000b008
R13: 0000000000000008 R14: 000000000000b010 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff880079c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff880079fff000 CR3: 0000000001c0b000 CR4: 00000000001006f0
Stack:
ffff880079c0cd80 000000000000b008 0000000000000008 ffff880075507e88
ffffffff810aecb0 ffff880079c0cd80 ffff880075507e98 ffffffff81030168
ffff880075507ed8 ffffffff81d1104f 00000000000000c3 0000000000000000
Call Trace:
[<ffffffff810aecb0>] clockevents_config_and_register+0x20/0x30
[<ffffffff81030168>] setup_APIC_timer+0xc8/0xd0
[<ffffffff81d1104f>] setup_boot_APIC_clock+0x4cc/0x4d8
[<ffffffff81d0f5de>] native_smp_prepare_cpus+0x3dd/0x3f0
[<ffffffff81d02ee9>] kernel_init_freeable+0xc3/0x205
[<ffffffff8177c910>] ? rest_init+0x90/0x90
[<ffffffff8177c91e>] kernel_init+0xe/0x120
[<ffffffff8178deec>] ret_from_fork+0x7c/0xb0
[<ffffffff8177c910>] ? rest_init+0x90/0x90
Prevent this from happening by:
1) Modifying try_msr_calibrate_tsc() to return calibration value or zero
if it fails.
2) Check this return value in native_calibrate_tsc() and in case of zero
fallback to use normal non-MSR based calibration.
[mw: Added subject and changelog]
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1392810750-18660-1-git-send-email-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix tegra_init_cache() to check whether the system has a PL310 cache
before touching the PL310 registers. This prevents access to non-existent
registers on Tegra114 and later.
Note for stable kernels:
In <= v3.12, the file to patch is arch/arm/mach-tegra/common.c.
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When building a kernel image with only CONFIG_CPU_IDLE but no CONFIG_PM,
we will get the following link error.
LD init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_enter_wait':
platform-spi_imx.c:(.text+0x25c0): undefined reference to `imx6q_set_lpm'
platform-spi_imx.c:(.text+0x25d4): undefined reference to `imx6q_set_lpm'
arch/arm/mach-imx/built-in.o: In function `imx6q_cpuidle_init':
platform-spi_imx.c:(.init.text+0x75d4): undefined reference to `imx6q_set_chicken_bit'
make[1]: *** [vmlinux] Error 1
Since pm-imx6q.c has been a collection of library functions that access
CCM low-power registers used by not only suspend but also cpuidle and
other drivers, let's build pm-imx6q.c independently of CONFIG_PM to fix
above error.
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@vger.kernel.org
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.
Fixes: 553c0a200e ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
The corresponding driver didn't make it into v3.14, so we need to remove
the node. Dove systems fail to boot with the node present and no
driver.
This node will be re-added when the driver makes it to mainline.
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add DSB after icache flush to complete the cache maintenance operation.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull AVR32 fixes from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: add generic vga.h to Kbuild
avr32: add generic ioremap_wc() definition in io.h
avr32: Makefile: add '-D__linux__' flag for gcc-4.4.7 use
avr32: fix missing module.h causing build failure in mimc200/fram.c
Pull powerpc fixes from Ben Herrenschmidt:
"Here are some more powerpc fixes for 3.14
The main one is a nasty issue with the NUMA balancing support which
requires a small generic change and the addition of a new accessor to
set _PAGE_NUMA. Both have been reviewed and acked by Mel and Rik.
The changelog should have plenty of details but basically, without
this fix, we get random user segfaults and/or corruptions due to
missing TLB/hash flushes. Aneesh series of 3 patches fixes it.
We have some vDSO vs. perf fixes from Anton, some small EEH fixes
from Gavin, a ppc32 regression vs the stack overflow detector, and a
fix for the way we handle PCIe host bridge speed settings on pseries
(which is needed for proper operations of AMD graphics cards on
Power8)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Disable EEH on reboot
powerpc/eeh: Cleanup on eeh_subsystem_enabled
powerpc/powernv: Rework EEH reset
powerpc: Use unstripped VDSO image for more accurate profiling data
powerpc: Link VDSOs at 0x0
mm: Use ptep/pmdp_set_numa() for updating _PAGE_NUMA bit
mm: Dirty accountable change only apply to non prot numa case
powerpc/mm: Add new "set" flag argument to pte/pmd update function
powerpc/pseries: Add Gen3 definitions for PCIE link speed
powerpc/pseries: Fix regression on PCI link speed
powerpc: Set the correct ksp_limit on ppc32 when switching to irq stack
Need add generic "vga.h", or can not pass building for allmodconfig,
the related error:
CC [M] drivers/gpu/drm/drm_irq.o
In file included from include/linux/vgaarb.h:34,
from drivers/gpu/drm/drm_irq.c:42:
include/video/vga.h:22:21: error: asm/vga.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
Need generic ioremap_wc(), or can not pass compiling with allmodconfig,
the related error:
CC [M] drivers/gpu/drm/drm_bufs.o
drivers/gpu/drm/drm_bufs.c: In function 'drm_addmap_core':
drivers/gpu/drm/drm_bufs.c:217: error: implicit declaration of function 'ioremap_wc'
drivers/gpu/drm/drm_bufs.c:218: warning: assignment makes pointer from integer without a cast
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
For avr32 cross compiler, do not define '__linux__' internally, so it
will cause issue with allmodconfig.
The related error:
CC [M] fs/coda/psdev.o
In file included from include/linux/coda.h:64,
from fs/coda/psdev.c:45:
include/uapi/linux/coda.h:221: error: expected specifier-qualifier-list before 'u_quad_t'
The related toolchain version (which only download, not re-compile):
[root@gchen linux-next]# /upstream/toolchain/download/avr32-gnu-toolchain-linux_x86/bin/avr32-gcc -v
Using built-in specs.
Target: avr32
Configured with: /data2/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/src/gcc/configure --target=avr32 --host=i686-pc-linux-gnu --build=x86_64-pc-linux-gnu --prefix=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-languages=c,c++ --disable-nls --disable-libssp --disable-libstdcxx-pch --with-dwarf2 --enable-version-specific-runtime-libs --disable-shared --enable-doc --with-mpfr-lib=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/lib --with-mpfr-include=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/include --with-gmp=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --with-mpc=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-__cxa_atexit --disable-shared --with-newlib --with-pkgversion=AVR_32_bit_GNU_Toolchain_3.4.2_435 --with-bugurl=http://www
.atmel.com/avr
Thread model: single
gcc version 4.4.7 (AVR_32_bit_GNU_Toolchain_3.4.2_435)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
Cc: stable@vger.kernel.org
Causing this:
In file included from arch/avr32/boards/mimc200/fram.c:13:
include/linux/miscdevice.h:51: error: field 'list' has incomplete type
include/linux/miscdevice.h:55: error: expected specifier-qualifier-list before 'mode_t'
arch/avr32/boards/mimc200/fram.c:42: error: 'THIS_MODULE' undeclared here (not in a function)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: stable@vger.kernel.org
The frame PC value in the unwind code used to just take the saved LR
value and use that. That's incorrect as a stack trace, since it shows
the return path stack, not the call path stack.
In particular, it shows faulty information in case the bl is done as
the very last instruction of one label, since the return point will be
in the next label. That can easily be seen with tail calls to panic(),
which is marked __noreturn and thus doesn't have anything useful after it.
Easiest here is to just correct the unwind code and do a -4, to get the
actual call site for the backtrace instead of the return site.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We possiblly detect EEH errors during reboot, particularly in kexec
path, but it's impossible for device drivers and EEH core to handle
or recover them properly.
The patch registers one reboot notifier for EEH and disable EEH
subsystem during reboot. That means the EEH errors is going to be
cleared by hardware reset or second kernel during early stage of
PCI probe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When doing reset in order to recover the affected PE, we issue
hot reset on PE primary bus if it's not root bus. Otherwise, we
issue hot or fundamental reset on root port or PHB accordingly.
For the later case, we didn't cover the situation where PE only
includes root port and it potentially causes kernel crash upon
EEH error to the PE.
The patch reworks the logic of EEH reset to improve the code
readability and also avoid the kernel crash.
Cc: stable@vger.kernel.org
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing a lot of hits in the VDSO that are not resolved by perf.
A while(1) gettimeofday() loop shows the issue:
27.64% [vdso] [.] 0x000000000000060c
22.57% [vdso] [.] 0x0000000000000628
16.88% [vdso] [.] 0x0000000000000610
12.39% [vdso] [.] __kernel_gettimeofday
6.09% [vdso] [.] 0x00000000000005f8
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We are using a stripped VDSO image which means only symbols with
relocation info can be resolved. There isn't a lot of point to
stripping the VDSO, the debug info is only about 1kB:
4680 arch/powerpc/kernel/vdso64/vdso64.so
5815 arch/powerpc/kernel/vdso64/vdso64.so.dbg
By using the unstripped image, we can resolve all the symbols in the
VDSO and the perf profile data looks much better:
76.53% [vdso] [.] __do_get_tspec
12.20% [vdso] [.] __kernel_gettimeofday
5.05% [vdso] [.] __get_datapage
3.20% test [.] main
2.92% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
perf is failing to resolve symbols in the VDSO. A while (1)
gettimeofday() loop shows:
93.99% [vdso] [.] 0x00000000000005e0
3.12% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.81% test [.] main
The reason for this is that we are linking our VDSO shared libraries
at 1MB, which is a little weird. Even though this is uncommon, Alan
points out that it is valid and we should probably fix perf userspace.
Regardless, I can't see a reason why we are doing this. The code
is all position independent and we never rely on the VDSO ending
up at 1M (and we never place it there on 64bit tasks).
Changing our link address to 0x0 fixes perf VDSO symbol resolution:
73.18% [vdso] [.] 0x000000000000060c
12.39% [vdso] [.] __kernel_gettimeofday
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We still have some local symbol resolution issues that will be
fixed in a subsequent patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Archs like ppc64 doesn't do tlb flush in set_pte/pmd functions when using
a hash table MMU for various reasons (the flush is handled as part of
the PTE modification when necessary).
ppc64 thus doesn't implement flush_tlb_range for hash based MMUs.
Additionally ppc64 require the tlb flushing to be batched within ptl locks.
The reason to do that is to ensure that the hash page table is in sync with
linux page table.
We track the hpte index in linux pte and if we clear them without flushing
hash and drop the ptl lock, we can have another cpu update the pte and can
end up with duplicate entry in the hash table, which is fatal.
We also want to keep set_pte_at simpler by not requiring them to do hash
flush for performance reason. We do that by assuming that set_pte_at() is
never *ever* called on a PTE that is already valid.
This was the case until the NUMA code went in which broke that assumption.
Fix that by introducing a new pair of helpers to set _PAGE_NUMA in a
way similar to ptep/pmdp_set_wrprotect(), with a generic implementation
using set_pte_at() and a powerpc specific one using the appropriate
mechanism needed to keep the hash table in sync.
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pte_update() is a powerpc-ism used to change the bits of a PTE
when the access permission is being restricted (a flush is
potentially needed).
It uses atomic operations on when needed and handles the hash
synchronization on hash based processors.
It is currently only used to clear PTE bits and so the current
implementation doesn't provide a way to also set PTE bits.
The new _PAGE_NUMA bit, when set, is actually restricting access
so it must use that function too, so this change adds the ability
for pte_update() to also set bits.
We will use this later to set the _PAGE_NUMA bit.
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rev3 of the PCI Express Base Specification defines a Supported Link
Speeds Vector where the bit definitions within this field are:
Bit 0 - 2.5 GT/s
Bit 1 - 5.0 GT/s
Bit 2 - 8.0 GT/s
This vector definition is used by the platform firmware to export the
maximum and current link speeds of the PCI bus via the
"ibm,pcie-link-speed-stats" device-tree property.
This patch updates pseries_root_bridge_prepare() to detect Gen3
speed buses (defined by 0x04).
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 5091f0c (powerpc/pseries: Fix PCIE link speed endian issue)
introduced a regression on the PCI link speed detection using the
device-tree property. The ibm,pcie-link-speed-stats property is composed
of two 32-bit integers, the first one being the maxinum link speed and
the second the current link speed. The changes introduced by the
aforementioned commit are considering just the first integer.
Fix this issue by changing how the property is accessed, using the
helper functions to properly access the array of values. The explicit
byte swapping is not needed anymore here, since it's done by the helper
functions.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Guenter Roeck has got the following call trace on a p2020 board:
Kernel stack overflow in process eb3e5a00, r1=eb79df90
CPU: 0 PID: 2838 Comm: ssh Not tainted 3.13.0-rc8-juniper-00146-g19eca00 #4
task: eb3e5a00 ti: c0616000 task.ti: ef440000
NIP: c003a420 LR: c003a410 CTR: c0017518
REGS: eb79dee0 TRAP: 0901 Not tainted (3.13.0-rc8-juniper-00146-g19eca00)
MSR: 00029000 <CE,EE,ME> CR: 24008444 XER: 00000000
GPR00: c003a410 eb79df90 eb3e5a00 00000000 eb05d900 00000001 65d87646 00000000
GPR08: 00000000 020b8000 00000000 00000000 44008442
NIP [c003a420] __do_softirq+0x94/0x1ec
LR [c003a410] __do_softirq+0x84/0x1ec
Call Trace:
[eb79df90] [c003a410] __do_softirq+0x84/0x1ec (unreliable)
[eb79dfe0] [c003a970] irq_exit+0xbc/0xc8
[eb79dff0] [c000cc1c] call_do_irq+0x24/0x3c
[ef441f20] [c00046a8] do_IRQ+0x8c/0xf8
[ef441f40] [c000e7f4] ret_from_except+0x0/0x18
--- Exception: 501 at 0xfcda524
LR = 0x10024900
Instruction dump:
7c781b78 3b40000a 3a73b040 543c0024 3a800000 3b3913a0 7ef5bb78 48201bf9
5463103a 7d3b182e 7e89b92e 7c008146 <3ba00000> 7e7e9b78 48000014 57fff87f
Kernel panic - not syncing: kernel stack overflow
CPU: 0 PID: 2838 Comm: ssh Not tainted 3.13.0-rc8-juniper-00146-g19eca00 #4
Call Trace:
The reason is that we have used the wrong register to calculate the
ksp_limit in commit cbc9565ee8 (powerpc: Remove ksp_limit on ppc64).
Just fix it.
As suggested by Benjamin Herrenschmidt, also add the C prototype of the
function in the comment in order to avoid such kind of errors in the
future.
Cc: stable@vger.kernel.org # 3.12
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The first is a fix for the way the ring buffer stores timestamps.
After a restructure of the code was done, the ring buffer timestamp
logic missed the fact that the first event on a sub buffer is to have
a zero delta, as the full timestamp is stored on the sub buffer itself.
But because the delta was not cleared to zero, the timestamp for that
event will be calculated as the real timestamp + the delta from the
last timestamp. This can skew the timestamps of the events and
have them say they happened when they didn't really happen. That's bad.
The second fix is for modifying the function graph caller site.
When the stop machine was removed from updating the function tracing
code, it missed updating the function graph call site location.
It is still modified as if it is being done via stop machine. But it's not.
This can lead to a GPF and kernel crash if the function graph call site
happens to lie between cache lines and one CPU is executing it while
another CPU is doing the update. It would be a very hard condition to
hit, but the result is sever enough to have it fixed ASAP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJS/2leAAoJEKQekfcNnQGu7nYH/AltUO19AgM2sFLOLM7Q0dp4
Lg7vE8CLKtFq0fjtv/ri//fJ56Lr+/WNHiiD06aIrgnMVBbWynS0m0RO+9bhFl8/
rELiUpXTTruqljmlT2T5lPxk+ZKgtLbxK8hNywU99eLgkTwyaOwrSUol30E8pw41
UwtKg4OAn1LbjQ8/sddVynGlFDNRdqFiGTIDvhHqI6F6/QlaEX81EeZbLThDU4D/
l86fMuIdw5pb+efa29Rr0s7O4Xol7SJgnSMVgd0OYADRFmp4sg+MKxuJAUjPsHk7
9vvbylOb4w5H6lo5h7kUee3w7kG+FjYVoEx+Sqq9936+KlwtN0kbiNvl0DkrXnY=
=kUmM
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull twi tracing fixes from Steven Rostedt:
"Two urgent fixes in the tracing utility.
The first is a fix for the way the ring buffer stores timestamps.
After a restructure of the code was done, the ring buffer timestamp
logic missed the fact that the first event on a sub buffer is to have
a zero delta, as the full timestamp is stored on the sub buffer
itself. But because the delta was not cleared to zero, the timestamp
for that event will be calculated as the real timestamp + the delta
from the last timestamp. This can skew the timestamps of the events
and have them say they happened when they didn't really happen.
That's bad.
The second fix is for modifying the function graph caller site. When
the stop machine was removed from updating the function tracing code,
it missed updating the function graph call site location. It is still
modified as if it is being done via stop machine. But it's not. This
can lead to a GPF and kernel crash if the function graph call site
happens to lie between cache lines and one CPU is executing it while
another CPU is doing the update. It would be a very hard condition to
hit, but the result is severe enough to have it fixed ASAP"
* tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/x86: Use breakpoints for converting function graph caller
ring-buffer: Fix first commit on sub-buffer having non-zero delta
Pull x86 EFI fixes from Peter Anvin:
"A few more EFI-related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Check status field to validate BGRT header
x86/efi: Fix 32-bit fallout
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=DDj5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A collection of ARM SoC fixes for v3.14-rc1.
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dma: mv_xor: Silence a bunch of LPAE-related warnings
ARM: ux500: disable msp2 device tree node
ARM: zynq: Reserve not DMAable space in front of the kernel
ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
ARM: imx6: Initialize low-power mode early again
ARM: pxa: fix various compilation problems
ARM: pxa: fix compilation problem on AM300EPD board
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
ata: sata_mv: Fix probe failures with optional phys
drivers: phy: Add support for optional phys
drivers: phy: Make NULL a valid phy reference
ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
ARM: moxart: move DMA_OF selection to driver
ARM: hisi: fix kconfig warning on HAVE_ARM_TWD
There have been reports of EFI crashes since -rc1. The following two
commits fix known issues.
* Fix boot failure on 32-bit EFI due to the recent EFI memmap changes
merged during the merge window - Borislav Petkov
* Avoid a crash during efi_bgrt_init() by detecting invalid BGRT
headers based on the 'status' field.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=+70Q
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"A small error handling problem and a compile breakage for ARM64"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Add VGIC device control for arm64
KVM: return an error code in kvm_vm_ioctl_register_coalesced_mmio()
Pull x86 fixes from Peter Anvin:
"A collection of small fixes:
- There still seem to be problems with asm goto which requires the
empty asm hack.
- If SMAP is disabled at compile time, don't enable it nor try to
interpret a page fault as an SMAP violation.
- Fix a case of unbounded recursion while tracing"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, smap: smap_violation() is bogus if CONFIG_X86_SMAP is off
x86, smap: Don't enable SMAP if CONFIG_X86_SMAP is disabled
compiler/gcc4: Make quirk for asm_volatile_goto() unconditional
x86: Use preempt_disable_notrace() in cycles_2_ns()
This fixes the build breakage introduced by
c07a0191ef and adds support for the device
control API and save/restore of the VGIC state for ARMv8.
The defines were simply missing from the arm64 header files and
uaccess.h must be implicitly imported from somewhere else on arm.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Madper reported seeing the following crash,
BUG: unable to handle kernel paging request at ffffffffff340003
IP: [<ffffffff81d85ba4>] efi_bgrt_init+0x9d/0x133
Call Trace:
[<ffffffff81d8525d>] efi_late_init+0x9/0xb
[<ffffffff81d68f59>] start_kernel+0x436/0x450
[<ffffffff81d6892c>] ? repair_env_string+0x5c/0x5c
[<ffffffff81d68120>] ? early_idt_handlers+0x120/0x120
[<ffffffff81d685de>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff81d6871e>] x86_64_start_kernel+0x13e/0x14d
This is caused because the layout of the ACPI BGRT header on this system
doesn't match the definition from the ACPI spec, and so we get a bogus
physical address when dereferencing ->image_address in efi_bgrt_init().
Luckily the status field in the BGRT header clearly marks it as invalid,
so we can check that field and skip BGRT initialisation.
Reported-by: Madper Xie <cxie@redhat.com>
Suggested-by: Toshi Kani <toshi.kani@hp.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
We do not enable the new efi memmap on 32-bit and thus we need to run
runtime_code_page_mkexec() unconditionally there. Fix that.
Reported-and-tested-by: Lejun Zhu <lejun.zhu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Unfortunatly the device tree for older OMAP35xx Overo cannot be used
with newer OMAP36xx and vice-versa. To address this issue, move most of
the Tobi DTS to a common include file, and create model-specific Tobi
DTS.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gumstix is the correct vendor for all Overo related products.
Reported-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tobi expansion board can be used with both OMAP35xx-based Overo,
and OMAP36xx-based Overo. Currently the boot is broken with newer
OMAP36xx-based Overo (Storm and alike). Fix include file and
compatible string to be able to boot newer models.
This will break older models. This will be addressed later.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 97411608fd ("ARM: OMAP2+: Remove legacy support for zoom
platforms") removed the Kconfig symbols MACH_OMAP_ZOOM2 and
MACH_OMAP_ZOOM3. Remove the last usage of the related macros too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The last caller of machine_is_nokia_n800() was removed in commit
5a87cde490 ("ARM: OMAP2+: Remove legacy booting support for n8x0").
That means that the Kconfig symbol MACH_NOKIA_N800 is now unused. It can
safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing compatible property to avoid problems in the future.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
N9/N950 does not boot anymore with 3.14-rc1, because SoC compatible
property is missing. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for tahvo-usb. This is the last missing piece to get
Tahvo USB working with 3.14.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: commit 75d3625e0e
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for ONENAND driver to probe later. However this does
not happen if generic MTD_ONENAND framework is built as module (CONFIG_MTD_ONENAND=m).
Therefore, when MTD/ONENAND and MTD/ONENAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
ONENAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_ONENAND=y || CONFIG_MTD_ONENAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: commit bc6b1e7b86
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for NAND driver to probe later. However this does
not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m).
Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
NAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Does not have an aux supply, and must be non-removable.
Otherwise it is removed during suspend and filesystem gets confused.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5, DRA7, AM43xx all have OPPs. So select the same to allow SoC
only configuration boot to work with OPP.
Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not
working on EVM-SK board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BMP085 EOC (End Of Conversion) irq line is connected to
gpio113 on gta04. Set irq properties to have driver using irq
instead polling for EOC.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_X86_SMAP is disabled, smap_violation() tests for conditions
which are incorrect (as the AC flag doesn't matter), causing spurious
faults.
The dynamic disabling of SMAP (nosmap on the command line) is fine
because it disables X86_FEATURE_SMAP, therefore causing the
static_cpu_has() to return false.
Found by Fengguang Wu's test system.
[ v3: move all predicates into smap_violation() ]
[ v2: use IS_ENABLED() instead of #ifdef ]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Link: http://lkml.kernel.org/r/20140213124550.GA30497@localhost
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.7+
If SMAP support is not compiled into the kernel, don't enable SMAP in
CR4 -- in fact, we should clear it, because the kernel doesn't contain
the proper STAC/CLAC instructions for SMAP support.
Found by Fengguang Wu's test system.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Link: http://lkml.kernel.org/r/20140213124550.GA30497@localhost
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.7+
Pull powerpc updates from Ben Herrenschmidt:
"Here is some powerpc goodness for -rc2. Arguably -rc1 material more
than -rc2 but I was travelling (again !)
It's mostly bug fixes including regressions, but there are a couple of
new things that I decided to drop-in.
One is a straightforward patch from Michael to add a bunch of P8 cache
events to perf.
The other one is a patch by myself to add the direct DMA (iommu
bypass) for PCIe on Power8 for 64-bit capable devices. This has been
around for a while, I had lost track of it. However it's been in our
internal kernels we use for testing P8 already and it affects only P8
related code. Since P8 is still unreleased the risk is pretty much
nil at this point"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/powernv: Add iommu DMA bypass support for IODA2
powerpc: Fix endian issues in kexec and crash dump code
powerpc/ppc32: Fix the bug in the init of non-base exception stack for UP
powerpc/xmon: Don't signal we've entered until we're finished printing
powerpc/xmon: Fix timeout loop in get_output_lock()
powerpc/xmon: Don't loop forever in get_output_lock()
powerpc/perf: Configure BHRB filter before enabling PMU interrupts
crypto/nx/nx-842: Fix handling of vmalloc addresses
powerpc/pseries: Select ARCH_RANDOM on pseries
powerpc/perf: Add Power8 cache & TLB events
powerpc/relocate fix relocate processing in LE mode
powerpc: Fix kdump hang issue on p8 with relocation on exception enabled.
powerpc/pseries: Disable relocation on exception while going down during crash.
powerpc/eeh: Drop taken reference to driver on eeh_rmv_device
powerpc: Fix build failure in sysdev/mpic.c for MPIC_WEIRD=y
When the conversion was made to remove stop machine and use the breakpoint
logic instead, the modification of the function graph caller is still
done directly as though it was being done under stop machine.
As it is not converted via stop machine anymore, there is a possibility
that the code could be layed across cache lines and if another CPU is
accessing that function graph call when it is being updated, it could
cause a General Protection Fault.
Convert the update of the function graph caller to use the breakpoint
method as well.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org # 3.5+
Fixes: 08d636b6d4 "ftrace/x86: Have arch x86_64 use breakpoints instead of stop machine"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull s390 bugfixes from Martin Schwidefsky:
"A collection a bug fixes. Most of them are minor but two of them are
more severe. The linkage stack bug can be used by user space to force
an oops, with panic_on_oops this is a denial-of-service. And the dump
memory detection issue can cause incomplete memory dumps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: improve cio_commit_config
s390: fix kernel crash due to linkage stack instructions
s390/dump: Fix dump memory detection
s390/appldata: restore missing init_virt_timer()
s390/qdio: correct program-controlled interruption checking
s390/qdio: for_each macro correctness
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
Commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
Fix this up by marking the node disabled again.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
GFP_ATOMIC is not a single gfp flag, but a macro which expands to the other
flags, where meaningful is the LACK of __GFP_WAIT flag. To check if caller
wants to perform an atomic allocation, the code must test for a lack of the
__GFP_WAIT flag. This patch fixes the issue introduced in v3.5-rc1.
CC: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
GFP_ATOMIC is not a single gfp flag, but a macro which expands to the other
flags and LACK of __GFP_WAIT flag. To check if caller wanted to perform an
atomic allocation, the code must test __GFP_WAIT flag presence. This patch
fixes the issue introduced in v3.6-rc5
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent changes to the pwm-backlight driver have made the power supply
mandatory. There is code in the regulator core to deal with situations
where no regulator is specified and provide a dummy, but that works on
DT-based boards only.
The situation can be remedied by adding a dummy regulator during board
initialization.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
We expose a number of OF properties in the kexec and crash dump code
and these need to be big endian.
Cc: stable@vger.kernel.org # v3.13
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We would allocate one specific exception stack for each kind of
non-base exceptions for every CPU. For ppc32 the CPU hard ID is
used as the subscript to get the specific exception stack for
one CPU. But for an UP kernel, there is only one element in the
each kind of exception stack array. We would get stuck if the
CPU hard ID is not equal to '0'. So in this case we should use the
subscript '0' no matter what the CPU hard ID is.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we set our cpu's bit in cpus_in_xmon, and then we take the
output lock and print the exception information.
This can race with the master cpu entering the command loop and printing
the backtrace. The result is that the backtrace gets garbled with
another cpu's exception print out.
Fix it by delaying the set of cpus_in_xmon until we are finished
printing.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As far as I can tell, our 70s era timeout loop in get_output_lock() is
generating no code.
This leads to the hostile takeover happening more or less simultaneously
on all cpus. The result is "interesting", some example output that is
more readable than most:
cpu 0x1: Vector: 100 (Scypsut e0mx bR:e setV)e catto xc0p:u[ c 00
c0:0 000t0o0V0erc0td:o5 rfc28050000]0c00 0 0 0 6t(pSrycsV1ppuot
uxe 1m 2 0Rx21e3:0s0ce000c00000t00)00 60602oV2SerucSayt0y 0p 1sxs
Fix it by using udelay() in the timeout loop. The wait time and check
frequency are arbitrary, but seem to work OK. We already rely on
udelay() working so this is not a new dependency.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we enter with xmon_speaker != 0 we skip the first cmpxchg(), we also
skip the while loop because xmon_speaker != last_speaker (0) - meaning we
skip the second cmpxchg() also.
Following that code path the compiler sees no memory barriers and so is
within its rights to never reload xmon_speaker. The end result is we loop
forever.
This manifests as all cpus being in xmon ('c' command), but they refuse
to take control when you switch to them ('c x' for cpu # x).
I have seen this deadlock in practice and also checked the generated code to
confirm this is what's happening.
The simplest fix is just to always try the cmpxchg().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now the config_bhrb() PMU specific call happens after
write_mmcr0(), which actually enables the PMU for event counting and
interrupts. So there is a small window of time where the PMU and BHRB
runs without the required HW branch filter (if any) enabled in BHRB.
This can cause some of the branch samples to be collected through BHRB
without any filter applied and hence affects the correctness of
the results. This patch moves the BHRB config function call before
enabling interrupts.
Here are some data points captured via trace prints which depicts how we
could get PMU interrupts with BHRB filter NOT enabled with a standard
perf record command line (asking for branch record information as well).
$ perf record -j any_call ls
Before the patch:-
ls-1962 [003] d... 2065.299590: .perf_event_interrupt: MMCRA: 40000000000
ls-1962 [003] d... 2065.299603: .perf_event_interrupt: MMCRA: 40000000000
...
All the PMU interrupts before this point did not have the requested
HW branch filter enabled in the MMCRA.
ls-1962 [003] d... 2065.299647: .perf_event_interrupt: MMCRA: 40040000000
ls-1962 [003] d... 2065.299662: .perf_event_interrupt: MMCRA: 40040000000
After the patch:-
ls-1850 [008] d... 190.311828: .perf_event_interrupt: MMCRA: 40040000000
ls-1850 [008] d... 190.311848: .perf_event_interrupt: MMCRA: 40040000000
All the PMU interrupts have the requested HW BHRB branch filter
enabled in MMCRA.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Fixed up whitespace and cleaned up changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a driver for the ARCH_RANDOM hook in rng.c, so we should select
ARCH_RANDOM on pseries.
Without this the build breaks if you turn ARCH_RANDOM off.
This hasn't broken the build because pseries_defconfig doesn't specify a
value for PPC_POWERNV, which is default y, and selects ARCH_RANDOM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Relocation's code is not working in little endian mode because the r_info
field, which is a 64 bits value, should be read from the right offset.
The current code is optimized to read the r_info field as a 32 bits value
starting at the middle of the double word (offset 12). When running in LE
mode, the read value is not correct since only the MSB is read.
This patch removes this optimization which consist to deal with a 32 bits
value instead of a 64 bits one. This way it works in big and little endian
mode.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On p8 systems, with relocation on exception feature enabled we are seeing
kdump kernel hang at interrupt vector 0xc*4400. The reason is, with this
feature enabled, exception are raised with MMU (IR=DR=1) ON with the
default offset of 0xc*4000. Since exception is raised in virtual mode it
requires the vector region to be executable without which it fails to
fetch and execute instruction at 0xc*4xxx. For default kernel since kernel
is loaded at real 0, the htab mappings sets the entire kernel text region
executable. But for relocatable kernel (e.g. kdump case) we only copy
interrupt vectors down to real 0 and never marked that region as
executable because in p7 and below we always get exception in real mode.
This patch fixes this issue by marking htab mapping range as executable
that overlaps with the interrupt vector region for relocatable kernel.
Thanks to Ben who helped me to debug this issue and find the root cause.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Disable relocation on exception while going down even in kdump case. This
is because we are about clear htab mappings while kexec-ing into kdump
kernel and we may run into issues if we still have AIL ON.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit f5c57710dd ("powerpc/eeh: Use
partial hotplug for EEH unaware drivers") introduces eeh_rmv_device,
which may grab a reference to a driver, but not release it.
That prevents a driver from being removed after it has gone through EEH
recovery.
This patch drops the reference if it was taken.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 446f6d06fa ("powerpc/mpic: Properly
set default triggers") breaks the mpc7447_hpc_defconfig as follows:
CC arch/powerpc/sysdev/mpic.o
arch/powerpc/sysdev/mpic.c: In function 'mpic_set_irq_type':
arch/powerpc/sysdev/mpic.c:886:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:890:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:894:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:898:9: error: case label does not reduce to an integer constant
Looking at the cpp output (gcc 4.7.3), I see:
case mpic->hw_set[MPIC_IDX_VECPRI_SENSE_EDGE] |
mpic->hw_set[MPIC_IDX_VECPRI_POLARITY_POSITIVE]:
The pointer into an array appears because CONFIG_MPIC_WEIRD=y is set
for this platform, thus enabling the following:
-------------------
#ifdef CONFIG_MPIC_WEIRD
static u32 mpic_infos[][MPIC_IDX_END] = {
[0] = { /* Original OpenPIC compatible MPIC */
[...]
#define MPIC_INFO(name) mpic->hw_set[MPIC_IDX_##name]
#else /* CONFIG_MPIC_WEIRD */
#define MPIC_INFO(name) MPIC_##name
#endif /* CONFIG_MPIC_WEIRD */
-------------------
Here we convert the case section to if/else if, and also add
the equivalent of a default case to warn about unknown types.
Boot tested on sbc8548, build tested on all defconfigs.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Noonan forwarded a users report where they had a problem starting
vsftpd on a Xen paravirtualized guest, with this in dmesg:
BUG: Bad page map in process vsftpd pte:8000000493b88165 pmd:e9cc01067
page:ffffea00124ee200 count:0 mapcount:-1 mapping: (null) index:0x0
page flags: 0x2ffc0000000014(referenced|dirty)
addr:00007f97eea74000 vm_flags:00100071 anon_vma:ffff880e98f80380 mapping: (null) index:7f97eea74
CPU: 4 PID: 587 Comm: vsftpd Not tainted 3.12.7-1-ec2 #1
Call Trace:
dump_stack+0x45/0x56
print_bad_pte+0x22e/0x250
unmap_single_vma+0x583/0x890
unmap_vmas+0x65/0x90
exit_mmap+0xc5/0x170
mmput+0x65/0x100
do_exit+0x393/0x9e0
do_group_exit+0xcc/0x140
SyS_exit_group+0x14/0x20
system_call_fastpath+0x1a/0x1f
Disabling lock debugging due to kernel taint
BUG: Bad rss-counter state mm:ffff880e9ca60580 idx:0 val:-1
BUG: Bad rss-counter state mm:ffff880e9ca60580 idx:1 val:1
The issue could not be reproduced under an HVM instance with the same
kernel, so it appears to be exclusive to paravirtual Xen guests. He
bisected the problem to commit 1667918b64 ("mm: numa: clear numa
hinting information on mprotect") that was also included in 3.12-stable.
The problem was related to how xen translates ptes because it was not
accounting for the _PAGE_NUMA bit. This patch splits pte_present to add
a pteval_present helper for use by xen so both bare metal and xen use
the same code when checking if a PTE is present.
[mgorman@suse.de: wrote changelog, proposed minor modifications]
[akpm@linux-foundation.org: fix typo in comment]
Reported-by: Steven Noonan <steven@uplinklabs.net>
Tested-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Elena Ufimtseva <ufimtseva@gmail.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reserve space from 0x0 - __pa(swapper_pg_dir),
if kernel is loaded from 0, which is not DMAable.
It is causing problem with MMC driver and others
which want to add dma buffers to this space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
All of them are DT-related.
- fixes for typos in i2c and ohci clocks
- addition of a USB host node for at91sam9n12ek
- 2 DT documentation updates that have been sent a long time ago
- a new board based on the sama5d36 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJS9QjhAAoJEAf03oE53VmQwwMIAMj6mM4Fv042REUssGIeVGlk
kmt3NzFeQI2ipTsgdwloAd53Hvty9RiX0ww4ZIGnxy8eZdEaRy6aDCohQsCvfYtx
LDcGdmIZ9056+62h/dqEbKYzs23j+diSJPe5sJF3/EHRRrRtBLSccEjnAMYI+Vqx
Gpj4XplbG89yXQZb1sKCCo9OsScu1ncdXs6G1ghZt1WhcvDwRuf/C0Af5KYCOibs
iXyMYxw7dd2VS8DxABxfi4xhW/ZZFR5ml66XdEW6MQLRG5Z33v7v7S9Wt0DV8uqd
C+naFnbm09/miHFX8bGZeI1Yaavs+UhKdD86fCn0Mn4uHNr4IdqqLGPEkZpjyJA=
=m41s
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre:
First series of AT91 fixes for 3.14.
All of them are DT-related.
- fixes for typos in i2c and ohci clocks
- addition of a USB host node for at91sam9n12ek
- 2 DT documentation updates that have been sent a long time ago
- a new board based on the sama5d36 SoC
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Select CONFIG_SOC_DRA7XX so that we can boot dra7-evm.
DRA7 family are A15 based processors that supports LPAE and an
evolutionary update to the OMAP5 generation of processors.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Since commit 9e8147bb5e
"ARM: imx6q: move low-power code out of clock driver"
the kernel fails to boot on i.MX6Q/D if preemption is
enabled (CONFIG_PREEMPT=y). The kernel just hangs
before the console comes up.
The above commit moved the initalization of the low-power
mode setting (enabling clocked WAIT states), which was
introduced in commit 83ae20981a
"ARM: imx: correct low-power mode setting", from
imx6q_clks_init to imx6q_pm_init. Now it is called
much later, after all cores are enabled.
This patch moves the low-power mode initialization back
to imx6q_clks_init again (and to imx6sl_clks_init).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Due to commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" some drivers fail
compilation, for example like this:
In file included from sound/soc/pxa/spitz.c:28:0:
sound/soc/pxa/spitz.c: In function ‘spitz_ext_control’:
arch/arm/mach-pxa/include/mach/spitz.h:111:30: error:
‘PXA_NR_BUILTIN_GPIO’ undeclared (first use in this function)
#define SPITZ_SCP_GPIO_BASE (PXA_NR_BUILTIN_GPIO)
(etc.)
This is caused by implicit inclusion of <mach/irqs.h> from
various board-specific headers under <mach/*> in the PXA
platform. So we take a sweep over these, and for every such
header that uses PXA_NR_BUILTIN_GPIO or PXA_GPIO_TO_IRQ()
we explicitly #include "irqs.h" so that we satisfy the
dependency in the board include file alone.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This board fails compilation like this:
arch/arm/mach-pxa/am300epd.c: In function ‘am300_cleanup’:
arch/arm/mach-pxa/am300epd.c:179:2: error: implicit declaration
of function ‘PXA_GPIO_TO_IRQ’ [-Werror=implicit-function-declaration]
free_irq(PXA_GPIO_TO_IRQ(RDY_GPIO_PIN), par);
This was caused by commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header"
This is because it was previously getting the macro PXA_GPIO_TO_IRQ
implicitly from <linux/gpio.h> which in turn implicitly included
<mach/gpio.h> which in turn included <mach/irqs.h>.
Add the missing include so that the board compiles again.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
When unlocking a spinlock, we require the following, strictly ordered
sequence of events:
<barrier> /* dmb */
<unlock>
<barrier> /* dsb */
<sev>
Whilst the code does indeed reflect this in terms of the architecture,
the final <barrier> + <sev> have been contracted into a single inline
asm without a "memory" clobber, therefore the compiler is at liberty to
reorder the unlock to the end of the above sequence. In such a case,
a waiting CPU may be woken up before the lock has been unlocked, leading
to extremely poor performance.
This patch reworks the dsb_sev() function to make use of the dsb()
macro and ensure ordering against the unlock.
Cc: <stable@vger.kernel.org>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During __v{6,7}_setup, we invalidate the TLBs since we are about to
enable the MMU on return to head.S. Unfortunately, without a subsequent
dsb instruction, the invalidation is not guaranteed to have completed by
the time we write to the sctlr, potentially exposing us to junk/stale
translations cached in the TLB.
This patch reworks the init functions so that the dsb used to ensure
completion of cache/predictor maintenance is also used to ensure
completion of the TLB invalidation.
Cc: <stable@vger.kernel.org>
Reported-by: Albin Tonnerre <Albin.Tonnerre@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit ad6492b8 added much needed memblock_virt_alloc_low() and further
commit 07bacb3 {memblock, bootmem: restore goal for alloc_low} fixed
the issue with low memory limit thanks to Yinghai. But even after all
these fixes, there is still one case where the limit check done with
ARCH_LOW_ADDRESS_LIMIT for low memory fails. Russell pointed out the
issue with 32 bit LPAE machines in below thread.
https://lkml.org/lkml/2014/1/28/364
Since on some LPAE machines where memory start address is beyond 4GB,
the low memory marker in memblock will be set to default
ARCH_LOW_ADDRESS_LIMIT which is wrong. We can fix this by letting
architectures set the ARCH_LOW_ADDRESS_LIMIT using another export
similar to memblock_set_current_limit() but am not sure whether
its worth the trouble. Tell me if you think otherwise.
Rather am just trying to fix that one broken case using
memblock_virt_alloc() in setup code since the memblock.current_limit
is updated appropriately makes it work on all ARM 32 bit machines.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Strashko, Grygorii <grygorii.strashko@ti.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The stage-2 memory attributes are distinct from the Hyp memory
attributes and the Stage-1 memory attributes. We were using the stage-1
memory attributes for stage-2 mappings causing device mappings to be
mapped as normal memory. Add the S2 equivalent defines for memory
attributes and fix the comments explaining the defines while at it.
Add a prot_pte_s2 field to the mem_type struct and fill out the field
for device mappings accordingly.
Cc: <stable@vger.kernel.org> [3.9+]
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct a typo causing the stack protector to be left enabled.
0xFFFFFFF -> 0xFFFFFFFF
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some drivers check if readq/writeq functions are defined.
If not internal driver functions are used which cause
compilation failures.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing param.h header because of HZ macro.
It is causing compilation failure:
In file included from include/linux/delay.h:14:0,
from drivers/clk/qcom/reset.c:18:
drivers/clk/qcom/reset.c: In function 'qcom_reset':
arch/microblaze/include/asm/delay.h:39:35: error: 'HZ'
undeclared (first use in this function)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When debug preempt is enabled, preempt_disable() can be traced by
function and function graph tracing.
There's a place in the function graph tracer that calls trace_clock()
which eventually calls cycles_2_ns() outside of the recursion
protection. When cycles_2_ns() calls preempt_disable() it gets traced
and the graph tracer will go into a recursive loop causing a crash or
worse, a triple fault.
Simple fix is to use preempt_disable_notrace() in cycles_2_ns, which
makes sense because the preempt_disable() tracing may use that code
too, and it tracing it, even with recursion protection is rather
pointless.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140204141315.2a968a72@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current code forgets to change the CR4 state on the current CPU.
Use on_each_cpu() instead of smp_call_function().
Reported-by: Mark Davies <junk@eslaf.co.uk>
Suggested-by: Mark Davies <junk@eslaf.co.uk>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
Link: http://lkml.kernel.org/n/tip-69efsat90ibhnd577zy3z9gh@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The spdif pinmux configuration must be connected to the spdif device to
take effect, not the spdif-transmitter.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mika Westerberg