pr_xxx() and dev_xxx() helpers ensure that all messages emitted by the
module have consistent prefixes, so let's use them. Also fix some
formatting issues.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a function pointer in the platform data of the DaVinci Keyscan driver
called device_enable, in order to perform board specific actions when
the device is initialized, like setup the PINMUX configuration.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When using realtime signals, we'll enqueue one signal for every event.
This is unfortunate, because (for example) keyboard presses are three
events: key, msc scancode, and syn. They'll be enqueued fast enough in
kernel space that all three events will be ready to read by the time
userspace runs, so the first invocation of the signal handler will read
all three events, but then the second two invocations still have to run
to do no work.
Instead, only send the SIGIO notification on syn events. This is a
slight abuse of SIGIO semantics, in principle it ought to fire as soon
as any events are readable. But it matches evdev semantics, which is
more important since SIGIO is rather vaguely defined to begin with.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to first unregister input device and only then cancel event work
since events can arrive (and cause event work to get scheduled again)
until input_unregister_device() returns.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs_remove_group() waits for sysfs attributes to be removed, therefore
we do not need to worry about driver-specific attributes being accessed
after driver has been detached from the device. In fact, attempts to take
serio->drv_mutex in attribute methods may lead to the following deadlock:
sysfs_read_file()
fill_read_buffer()
sysfs_get_active_two()
psmouse_attr_show_helper()
serio_pin_driver()
serio_disconnect_driver()
mutex_lock(&serio->drv_mutex);
<--------> mutex_lock(&serio_drv_mutex);
psmouse_disconnect()
sysfs_remove_group(... psmouse_attr_group);
....
sysfs_deactivate();
wait_for_completion();
Fix this by removing calls to serio_[un]pin_driver() and functions themselves
and using driver-private mutexes to serialize access to attribute's set()
methods that may change device state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - wait for command completion when closing the device
Input: twl4030-pwrbutton - switch to using threaded IRQ
Input: twl4030_keypad - switch to using threaded IRQ
Input: lifebook - add CONFIG_DMI dependency
Input: wistron - fix test for CONFIG_PM
Input: psmouse - fix compile warning in hgpk module
Input: matrix-keypad - handle cases when GPIOs can't be wakeup sources
Input: iforce - fix oops on device disconnect
Input: ff-memless - add notion of direction to for rumble effects
Input: ff-memless - another fix for signed to unsigned overflow
Input: ff-memless - start playing FF effects immediately
Input: serio - do not mark kseriod freezable anymore
Input: speed up suspend/shutdown for PS/2 mice and keyboards
We need to wait for the command to disable FF effects to complete before
continuing with closing the device.
Tested-by: Johannes Ebke <johannes.ebke@physik.uni-muenchen.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Certain devices implement triggers as buttons rather than axes. In
particular, arcade sticks such as the HORI Real Arcade Pro.EX do not
have analog buttons.
These devices are now setup to present buttons rather than axes for
triggers.
User-space applications often also have problems with
axes-as-buttons. Activating MAP_TRIGGERS_TO_BUTTONS for a device
removes the artificial difference between buttons and triggers.
Signed-off-by: Nicolas Léveillé <nicolas@uucidl.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Lifebook protocol can only be activated if we find known DMI signature.
It is useles without DMI.
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This should fix the following compile warning:
drivers/input/misc/wistron_btns.c:1331:5: warning: "CONFIG_PM" is not defined
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On certain boards not all GPIOs may be used as wakeup sources, in which
case some of enable_irq_wake() calls will fail. On resume calling
disable_irq_wake() will warn about unbalanced IRQ wake disable.
Solve this by checking whether enable_irq_wake() succeeded or not and
no not call disable_irq_wake() for these GPIOs/IRQs that have not been
enabled.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not try to free iforce device when we closing input device; disconnect
is the only place where it should be deleted.
Reported-by: Johannes Ebke <johannes.ebke@physik.uni-muenchen.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds simple direction calculation when combining effects. It's useful
to decide motor direction for rumble (vibrator).
Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The commit 9e68177ef9 changed 'gain' from
signed to unsigned to fix an issue with rumble effect calculation, however
it introduced problems when calculating constant effects. Having 'gain'
being unsigned int was an unfortunate choice since it dominates all
implicit type conversions causing everything to be treated as unsigned
int.
Let's change it back to signed int and simply add proper casts to rumble
effect calculations.
Reported-by: Gary Stein <lordcnidarian@gmail.com>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of waiting for the next timer tick to start playing an effect
do it immediately. This mostly helps systems using low HZ setting.
Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We used to make kseriod freezable to prevent unnecessary attempts at
resuming keyboard and mouse before taking hibernation image when suspend
and hibernation were sharing PM operations. Now that they are separated
and we don't risk resuming during 'thaw' we don't need to freeze kseriod
anymore. This will allow us to start resetting mouse and keyboard a bit
earlier, before rest of the userspace comes back up.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of doing full-blown reset while suspending or shutting down
the box use lighter form of reset that should take less time.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
Input: ALPS - add interleaved protocol support (Dell E6x00 series)
Input: keyboard - don't override beep with a bell
Input: altera_ps2 - fix test of unsigned in altera_ps2_probe()
Input: add mc13783 touchscreen driver
Input: ep93xx_keypad - update driver to new core support
Input: wacom - separate pen from express keys on Graphire
Input: wacom - add defines for data packet report IDs
Input: wacom - add support for new LCD tablets
Input: wacom - add defines for packet lengths of various devices
Input: wacom - ensure the device is initialized properly upon resume
Input: at32psif - do not sleep in atomic context
Input: i8042 - add Gigabyte M1022M to the noloop list
Input: i8042 - allow installing platform filters for incoming data
Input: i8042 - fix locking in interrupt routine
Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad
Input: document use of input_event() function
Input: sa1111ps2 - annotate probe() and remove() methods
Input: ambakmi - annotate probe() and remove() methods
Input: gscps2 - fix probe() and remove() annotations
Input: altera_ps2 - add annotations to probe and remove methods
...
Properly handle version of the protocol where standard PS/2 packets
from trackpoint are stuffed into middle (byte 3-6) of the standard
ALPS packets when both the touchpad and trackpoint are used together.
The patch is based on work done by Matthew Chapman and additional
research done by David Kubicek and Erik Osterholm:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/296610
Many thanks to David Kubicek for his efforts in researching fine points
of this new version of the protocol, especially interaction between pad
and stick in these models.
Signed-off-by: Sebastian Kapfer <sebastian_kapfer@gmx.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver provides support for the touchscreen interface
integrated into the Freescale MC13783.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver was merged before the ep93xx core support was added
for the keypad clock and acquiring/releasing the necessary gpio's.
Now that the proper support is in the ep93xx core this driver
needs to be updated to work correctly.
Summary of changes:
1) Remove some unused members from the platform data.
2) Remove the custom KEY macro and use the ones available in
<linux/input/matrix_keypad.h>
3) Remove the keypad_{readl/writel} macros and just use
__raw_{readl/writel} directly.
4) Update the clk_set_rate() call to work with the core support.
5) Cleanup the probe routine and remove some unneeded messages.
6) Use the ep93xx core functions to acquire and release the gpio's.
7) Fix the clk_get() call to get the keypad clock.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since Graphire/Bamboo devices report pen and expresskeys in the same
data packet, we need to send a input_sync event to separate pen data
from expresskeys for X11 driver to process them properly.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for the foolowing Wacom devices:
- 0x9F - a single touch only LCD tablet;
- 0xE2 - a two finger touch only LCD tablet;
- 0xE3 - a two finger touch, penabled LCD tablet.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Call wacom_query_tablet_data() from wacom_resume() so the device will be
switched to Wacom mode upon resume. Devices that require this are: regular
tablets and two finger touch devices.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We can't use msleep() while holding a spinlock, moreower serio's write()
method is supposed to be useable from inettrupt context. Let's do what
i8042 does and poll the status register every 50 us (with udelay).
Reported-by: Marjan Fojkar <marjan@pajkc.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Gigabyte netbook model M1022M requires i8042.noloop, otherwise AUX port
will not detected and the touchpad will not work. Unfortunately chassis
type in DMI set to "Other" and thus generic laptop entry does not fire
on it.
Reported-by: Darryl Bond <dbond@nrggos.com.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since platform_device_add_data copies the passed data, the allocated
subdev_pdata is never freed. A simple fix would be to either free subdev_pdata
or put it onto the stack. But since the pcf50633 child devices can rely on
beeing children of the pcf50633 core device it's much more elegant to get access
to pcf50633 core structure through that link. This allows to get completly rid
of pcf5033_subdev_pdata.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some hardware (such as Dell laptops) signal a variety of events through
the i8042 controller, even if these don't map to keyboard events. Add
support for drivers to filter the i8042 event stream in order to respond
to these events and (if appropriate) block them from entering the input
stream.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to protect not only i8042 status and data register from concurrent
access from IRQ 1 and 12 but the rest of the shared state as well, so let's
move release of i8042_lock in i8042_interrupt() a little bit further down.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Relative events are only reported via secondary device therefore device
associated with the touchpad should not advertise these capabilities.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Mark altera_ps2_probe() as __devinit and altera_ps2_remove() as __devexit
so that they can be discarded when not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
del_timer() does not wait for the timer to finish running before returning
and therefore is technically not safe. Also make sure to enable tasklet
before kicking timer that will schedule it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Setting up owner field ensures that driver core creates symlink from
the driver to a module implementing this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen pvfb: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: If FBINFO_VIRTFB is defined, do not set VM_IO flag.
Fix toogle whether xenbus driver should be built as module or part of kernel.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
* 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
agp: Remove the BKL from agp_open
inifiband: Remove BKL from ipath_open()
mips: Remove BKL from tb0219
drivers: Remove BKL from scx200_gpio
drivers: Remove BKL from pc8736x_gpio
parisc: Remove BKL from eisa_eeprom
rtc: Remove BKL from efirtc
input: Remove BKL from hp_sdc_rtc
hw_random: Remove BKL from core
macintosh: Remove BKL from ans-lcd
nvram: Drop the bkl from non-generic nvram_llseek()
nvram: Drop the bkl from nvram_llseek()
mem_class: Drop the bkl from memory_open()
spi: Remove BKL from spidev_open
drivers: Remove BKL from cs5535_gpio
drivers: Remove BKL from misc_open
More and more devices choose to reimplement support for sparse keymaps
first introduced by wistron driver. Move it into a library module so it
can be easily used by interested parties.
Reviewed-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
DMI tables use considerable amount of memory. Mark them as __initconst
so they will be discarded once module is loaded.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keyboard handler should not attempt to traverse handler->h_list on
its own, without any locking, otherwise it races with registering
and unregistering of input handles which leads to crashes.
Introduce input_handler_for_each_handle() helper that allows safely
iterate over all handles attached to a particular handler and switch
keyboard handler to use it.
Reported-by: Jim Paradis <jparadis@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to read and report gpio state when we bind the driver to the
device and upon resume so that userspace has correct state of the
switches (and keys but they are less important since, even if they
are happened to be pressed, we'd expect them to be released fairly
soon).
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the ET&T TC5UH 5-wire USB touchscreen controller.
More info at http://www.etandt.com.tw/board_solution.html
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Added two new Xbox 360 devices:
- HORI Real Arcade Pro.EX
- Mad Catz SFIV Fightpad
Signed-off-by: Nicolas Léveillé <nicolas@uucidl.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch moves the KEYSC header file from the
SuperH specific asm directory to a place where
it can be shared by multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If the poll interval is set to 0 via new sysfs entry and device is
opened after that, polling is started with interval 0. This causes
huge CPU load. Same happens if the rate was 0 when the device was
closed and then reopened.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It does not make sense to wait poll_interval before performing first
read after opening the device, schedule the read immediately instead.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
S3C24XX touchscreen driver, originally written by Arnaud Patard and
other contributors. The driver has had substantial testing as well as
a number of tidying up passes done by Ben Dooks, as noted:
- added kernel-doc comments to most of the routines
- removed old code from pre adc framework days
- updated device probe code to use platform id list matching
- cleaned up debug, since printk() now has timestamp feature
- ensure code uses dev_() reporting macros where necessary
- remove ABS_PRESSURE reporting, tslib can be fixed
- ensure timer is removed on driver exit
- move to using dev_pmops for power management
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Zytronic USB-attached capacitive touchscreen support within the generic
USB touchscreen driver.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Function name is input_ff_destroy() and not input_ff_free()
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use strlcat() to append a string to the previously created first part.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On Zaurus, hx4700 and others pressure is reported inverted -- the lighter
the pressure, the bigger numerical value.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
usb_kill_urb() in disconnect is not needed as unregistering will cause
close() to be called.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a number of plafrom dependent parameters to atmel_tsadcc. The
touchscreeen driver can now take into account the slight differences
that exist between IPs included in diferent products. This will also
allow to adapt its behaivior to the caracteristics of the resistive
panel used.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tiny patch for setting capabilities using input API function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The touchpad on Acer Aspire 5720, 5520 and some other Aspire models
(signature 0x73, 0x02, 0x50) has a button that can be rocked in 4
different directions. Make the driver to generate BTN_0..BTN_3 events
in response. The Synaptics driver by default maps BTN_0 and BTN_1 to
up and down, so there should be no visible changes with the old setup
that generated BTN_FORWARD and BTN_BACK (also mapped to up and down).
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not start protocol detection assuming that middle mouse is present,
instead let individual protocols explicitly set this capability.
This fixes issue with Synaptics touchpads pretending that they have
middle button when hardware clearly reports otherwise.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The main input device of Lifebook touchscreens does not generate
left/right/middle button events and therefore should not be advertising
them in its capabilities.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Elantech touchpads work in absolute mode and do not generate relative
events so they should not be advertising them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Touchkit PS/2 touchscreen does not have left/right/middle buttons and
should not be advertising as capable of generating these events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysfs entry for reading and setting of the polling interval. If the
interval is set to 0, polling is stopped. Polling is restarted when
interval is changed to non-zero.
sysfs entries:
poll = current polling interval in msec (RW)
max = max allowed polling interval (RO)
min = min allowed polling interval (RO)
Minimum and maximum limit for interval can be set while setting up the
device.
Interval can be adjusted even if the input device is not currently open.
[dtor@mail.ru: add kernel doc markup for the new fields]
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the code that deals with setting up each individual button out into
a new function to reduce the indentation and allow us to common up some
of the error recovery code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio keys driver should be using <linux/gpio.h> instead
of <asm/gpio.h>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_keys driver is binding to a platform device but using pr_err()
to report errors. Change to using dev_err() so that all messages are
prefixed by the device name.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch allows UCB1400 to get IRQ GPIO from platform data. In case
platform_data are not supplied or the IRQ supplied in the platform_data
is negative, fall back to the old IRQ detection algorithm.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Panasonic CF-72 uses 6-byte protocol and does not need to be tied
to a particular port.
Signed-off-by: Abner Holsinger <9zabner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit b7802c5c1e ("Input: psmouse - use boolean type") caused the
synaptics_hardware variable to be completely useless, as it is
constantly set to 'true' throughout the whole psmouse_extensions().
This was caused by the following hunk in the commit in question
- int synaptics_hardware = 0;
+ bool synaptics_hardware = true;
which is wrong and causes driver to issue extra reset when falling
back to bare PS/2 protocol.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The get parameter function should return a string without a life-feed.
Otherwise you'll see additional empty line in sysfs parameters file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should be sending EV_LED event down to drivers upon resume even in cases
when in-kernel state of the LED is off since device could come up with some
leds turned on.
Reported-and-tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that input core acquires dev->event_lock spinlock and disables
interrupts when propagating input events, using spin_lock_bh() in
ff-memless driver is not allowed. Actually, the timer_lock itself
is not needed anymore, we should simply use dev->event_lock
as well.
Also do a small cleanup in force-feedback core.
Reported-by: kerneloops.org
Reported-by: http://www.kerneloops.org/searchweek.php?search=ml_ff_set_gain
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move xen_domain and related tests out of asm-x86 to xen/xen.h so they
can be included whenever they are necessary.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is nothing that disallows gpio-keys to share it's IRQ line
w/ other drivers. Make it use IRQF_SHARED in request_irq().
An example of other driver with which I'd like to share IRQ line
for GPIO buttons is ledtrig-gpio.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/misc/winbond-cir.c depends on LEDS_TRIGGERS so
add an appropriate select to drivers/input/misc/Kconfig
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If user presses keys while i8042 is being initialized there is a chance
that keyboard data will be mistaken for results of Read Control Register
command causing futher troubles. Work around this issue by reading CTR
several times and stop when we get matching results.
Reported-and-tested-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for Dynapro serial touchscreen, which used to be
supported in Xorg. The driver needs updated inputattach utility to
initialize serial port and create proper serio device before the
driver will be bound to it.
Signed-off-by: Tias Guns <tias@ulyssis.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
OQO 01+ multimedia keys produce 6x on press, e0 6x upon release.
As a result, Linux thinks that another key has been pressed (or is
repeating), when it is actually a release of the same key. Mangle the
release scancode when running on OQO so that driver recognizes it as
such.
Since the device does not have external PS/2 ports mangling is safe
since there is no chance that an external keyboard is connected.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Optional open and close methods for preparing and closing
the device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If left unsigned the hp_sdc_rtc_read_i8042timer() return value will not
be checked correctly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some machines share same key list for volume up/down release key quirks,
use only one key list.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On this model, when KBD is in active multiplexing mode, acknowledgements
to reset and get ID commands issued on KBD port sometimes are delivered
to AUX3 port (touchpad) which messes up device detection. Legacy KBC
mode works fine and since there are no external PS/2 ports on this laptop
and no support for docking station we can safely disable active MUX mode.
Tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.884891604@linutronix.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
input_devices_seq_start() uses mutex_lock_interruptible() to acquire
the input_mutex, but doesn't properly handle the situation when the
call fails (for example due to interrupt). Instead of returning NULL
(which indicates that there is no more data) we should return
ERR_PTR()-encoded error.
We also need explicit flag indicating whether input_mutex was acquired
since input_devices_seq_stop() is called whether input_devices_seq_start()
was successful or not.
The same applies to input_handlers_seq_start().
Reported-by: iceberg <strakh@ispras.ru>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to postpone restoring LED state and typematic settings until
keyboard is finished reconnecting upon resume. Normally driver core
and PM infrastructure takes care of proper ordering and dependencies,
but or case actual reconnect is done asynchronously from kseriod.
So while driver core thinks that keyboard was resumed and it is time
to let input core run it's resume handlers in reality keyboard is not
ready yet. The solution is to keep rescheduling work that adjusts LED
and rate settings until keyboard is fully enabled.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver enables keypad support on DaVinci platforms. DM365 is the
only platform that uses this driver at the moment.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- no spaces between function name and opening parenthesis
- switch statements were indented too much
This makes checkpatch (and me) happy.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- no spaces between function name and opening parenthesis
- switch statements were indented too much
This makes checkpatch (and me) happy.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix breakage caused by commit 9605fb48e1
While the input core indeed takes care of restoring led state and
typematic settings upon resume the driver still need to initialize
them properly when registering a new device
Reported-and-tested-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a new SERIO driver to support the Altera University
Program PS/2 controller.
[dtor@mail.ru: assorted cleanups]
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This small snippet escaped last round of int -> bool conversion.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently some of Toshiba Protege M300 identify themselves as
"Portable PC" in DMI so we need to add that to the DMI table as
well. We need DMI data so we can automatically lower Synaptics
reporting rate from 80 to 40 pps to avoid over-taxing their
keyboard controllers.
Tested-by: Rod Davison <roddavison@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Sometimes it is not clear why IRQ delivery test failed so let's
add some debug printks so we know the exact reason.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The "select" statement in the Kconfig ensures that all other users
of the xenbus will have the same dependency.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
libps2 can not be built in if i8042 is a module, all other combinations
are allowed.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If the sub-probe functions fail, we need to pass up the error code to the
higher levels from the probe function. We currently always return 0 even
if there was an error so higher levels don't report problems.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When the rotart_encoder driver is used to report relative axis
information the "steps" in the platform data could be missing
since it's not relevant.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The function bbc_remove and grover_remove are used only wrapped
by __devexit_p so define it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/input.c:1277: warning: 'input_dev_reset' defined but not used
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix these warnings:
drivers/built-in.o: In function `apanel_remove':
apanel.c:(.text+0x56e852): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `apanel_probe':
apanel.c:(.text+0x56eae3): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `acpi_fujitsu_hotkey_add':
fujitsu-laptop.c:(.text+0x5d7647): undefined reference to `led_classdev_register'
fujitsu-laptop.c:(.text+0x5d76b5): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `wbcir_probe':
winbond-cir.c:(.devinit.text+0x5f375): undefined reference to `led_classdev_register'
winbond-cir.c:(.devinit.text+0x5f663): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `wbcir_remove':
winbond-cir.c:(.devexit.text+0x7f23): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `fujitsu_cleanup':
fujitsu-laptop.c:(.exit.text+0xbe37): undefined reference to `led_classdev_unregister'
fujitsu-laptop.c:(.exit.text+0xbe53): undefined reference to `led_classdev_unregister'
It happens because the new INPUT_WINBOND_CIR driver relies on new-leds
infrastructure - but does not select it in drivers/input/misc/Kconfig.
But it selects LEDS_CLASS, which confuses a number of other drivers into
thinking that all the leds infrastructure is in place.
Fix this by selecting NEW_LEDS as well, like similar drivers do.
Eventually, this whole leds infrastructure complexity should be
cleaned up, it's been going on for years.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/battery-2.6:
power_supply: Add driver for the PMU on WM831x PMICs
ds2760_battery: Fix integer overflow for time_to_empty_now
wm97xx_battery: Convert to dev_pm_ops
wm97xx_battery: Use irq to detect charger state
wm97xx_battery: Use platform_data
wm97xx-core: Pass platform_data to battery
ds2760_battery: implement set_charged() feature
power_supply: get_by_name and set_charged functionality
power_supply: EXPORT_SYMBOL cleanups
ds2760_battery: add current_accum module parameter
ds2760_battery: handle full_active_uAh == 0 case correctly
ds2760_battery: add rated_capacity module parameter
ds2760_battery: export more features
ds2760_battery: delay power supply registration
wm8350_power: Implement charge type property
power_supply: Add a charge_type property, and use it for olpc driver
olpc_battery: Add an 'error' sysfs device that displays raw errors
Revert "power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL"
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This version only supports individual cells (no slide support yet).
The code has been tested on proprietary development ARM board, but
should work fine on other machines.
Signed-off-by: Raphael Derosso Pereira <raphaelpereira@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
Add a driver for the the Consumer IR (CIR) functionality of the Winbond
WPCD376I chipset (found on e.g. Intel DG45FC motherboards).
Signed-off-by: David Härdeman <david@hardeman.nu>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert max7359 driver to use IRQ threading instead of using
workqueue.
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Maxim MAX7359 is a I2C interfaced key switch controller which
provides microprocessors with management of up to 64 key switches.
This patch adds support for the MAX7359 key switch controller.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
The MELPAS MCS-5000 is the touchscreen controller. The overview of this
controller can see at the following website:
http://www.melfas.com/product/product01.asp?k_r=eng_
This driver is tested on s3c6410 NCP board and supports only the i2c
interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The genirq already provides default hard IRQ handler for threaded
IRQs, no need to implement our own here.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
cancel_delayed_work() may spin and therefore should not be used in
interrupt contexts.
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AD7889 is a new part but 100% software compatible with the AD7879, so
add it to the id_table and help text.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that input core takes care of restoring state of input devices
upon resume we don't need to do anything special here.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Automatically turn off leds and sound effects as part of suspend
process and restore led state, sounds and repeat rate at resume.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The serio ports on i8042 are not completely isolated; while we provide
enough locking to ensure proper serialization when accessing control
and data registers AUX and KBD ports can still have an effect on each
other on PS/2 protocol level. The most prominent effect is that
issuing a command for the device connected to one port may cause
abort of the command currently executing by the device connected to
another port.
Since i8042 nor serio subsystem are not aware of the details of the
PS/2 protocol (length of the commands and their replies and so on) the
locking should be done on libps2 level by adding special handling when
we see that we are dealing with serio port on i8042.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for misc input events for the PCAP2 PMIC, it handles
the Power key and the Headphone button.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Ilya Petrov <ilya.muromec@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Touchscreen driver for the PCAP2 multi function device used in
Motorola EZX smartphones.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of PMICs support control of initial power on
through the ON pin on the device with soft control of the pin
at other times. Represent this to userspace as KEY_POWER.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: devtmpfs - kernel-maintained tmpfs-based /dev
debugfs: Modify default debugfs directory for debugging pktcdvd.
debugfs: Modified default dir of debugfs for debugging UHCI.
debugfs: Change debugfs directory of IWMC3200
debugfs: Change debuhgfs directory of trace-events-sample.h
debugfs: Fix mount directory of debugfs by default in events.txt
hpilo: add poll f_op
hpilo: add interrupt handler
hpilo: staging for interrupt handling
driver core: platform_device_add_data(): use kmemdup()
Driver core: Add support for compatibility classes
uio: add generic driver for PCI 2.3 devices
driver-core: move dma-coherent.c from kernel to driver/base
mem_class: fix bug
mem_class: use minor as index instead of searching the array
driver model: constify attribute groups
UIO: remove 'default n' from Kconfig
Driver core: Add accessor for device platform data
Driver core: move dev_get/set_drvdata to drivers/base/dd.c
Driver core: add new device to bus's list before probing
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
Input: bcm5974 - silence uninitialized variables warnings
Input: wistron_btns - add keymap for AOpen 1557
Input: psmouse - use boolean type
Input: i8042 - use platform_driver_probe
Input: i8042 - use boolean type where it makes sense
Input: i8042 - try disabling and re-enabling AUX port at close
Input: pxa27x_keypad - allow modifying keymap from userspace
Input: sunkbd - fix formatting
Input: i8042 - bypass AUX IRQ delivery test on laptops
Input: wacom_w8001 - simplify querying logic
Input: atkbd - allow setting force-release bitmap via sysfs
Input: w90p910_keypad - move a dereference below a NULL test
Input: add twl4030_keypad driver
Input: matrix-keypad - add function to build device keymap
Input: tosakbd - fix cleaning up KEY_STROBEs after error
Input: joydev - validate axis/button maps before clobbering current ones
Input: xpad - add USB ID for the drumkit controller from Rock Band
Input: w90p910_keypad - rename driver name to match platform
Input: add new driver for Sentelic Finger Sensing Pad
Input: psmouse - allow defining read-only attributes
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
After KYCR2 is set, udelay might become necessary if there are only a
small number of keys attached. This patch introduces an optional delay
through the platform data to address this problem.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
i8042 is not hot-pluggable and we create the device when we register
the driver, so let's save some memory by using platform_device_probe
and using __init instead of __devinit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ever since we switched from having a polling timer to registering IRQ
handlers for both keyboard and AUX ports at the driver registration
time, on certain boxes probing for a mouse results in keyboard
stopping working. The only real difference between old and new way is
that before we disabled ports after unsuccessful probe whereas now we
leave them as is. Try to emulate the old behavior by disabling and
immediately re-enabling AUX and KBD ports when corresponding serio
port is being closed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It seems that many laptops do not fully implement AUX LOOP command in
their keyboard controllers, causing issues with touchpad detection.
We know however that almost every laptop/portable uses a PS/2 pointing
device and, even if user disables it in favor of an external mouse,
the system will not use IRQ 12 for anything else. Therefore we may
bypass AUX IRQ delivery test when running on a laptop and assume that
it is routed properly.
Just to be safe we require the box to have good PNP data in order to
bypass the test.
[Jin Dongming <jin.dongming@np.css.fujitsu.com>: fix crash caused
by missing terminator in the DMI table]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Compaq Presario R4000-series laptops are not sending a "volume up button
release" and "volume down button release" signal in the PS/2 protocol for
atkbd. The URL below has some of confirmed reports:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/385477
Signed-off-by: Dave Andrews <jetdog330@hotmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no need for locking when we send query and start commands
to the touchscreen since there is no concurrency.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are more and more laptop requiring use of force_release quirk
for their multimedia and other specialized keys. Adding their DMI data
to the kernel is not sustainable; instead we will rely on help from
userspace (HAL) to do that for us.
This patch creates a new 'force_release' sysfs attribute (that belongs
to serio device to which keyboard is attached) which can be used to set
up force_release keymap. For example, Dell laptop owners might do:
echo 133-139,143,147 > /sys/devices/platform/i8042/serio0/force_release
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add the cpu.c and dev.c and modify w90p910 platform
to apply to use the common API(provided by cpu.c and dev.c)
at the same time, I renamed all w90x900 to nuc900 in every
c file of w90x900 platform and touchscreen's driver name.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should first check whether platform data is NULL or not, before
dereferencing it to get the keymap.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a driver for the keypad controller on TWL4030 family chips.
These support up to an 8x8 key matrix. The TWL4030 multifunction
chips are mostly used on OMAP3 (or OMAP 2430) based boards.
[dtor@mail.ru: switch to matrix-keypad framework, fix changing
keymap from userspace]
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Direct to fail2 to gpio_free() the KEY_STROBEs as well as the KEY_SENSEs.
[dtor@mail.ru: change keymap from unsigned int to unsigned short]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Up to now axis and button map validation was done after the user-supplied
values were copied over the driver's map. This patch copies the
user-supplied values into temporary buffers and validated them before
overwriting the driver's permanent maps.
Also change JSIOCGBTNMAP and JSIOCGAXMAP to return number of bytes returned
to userspace instead of 0.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When KBC is in active multiplexing mode, disabling and re-enabling the
touchpad with the special key leaves the touchpad dead. Since the laptop
does not have any external PS/2 ports disabling MUX mode should be safe.
Reported-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes, when using the touchscreen, it stops working till next restart
and the following message is printed:
ucb1400: unexpected IE_STATUS = 0x0
The following patch retriggers the touchscreen interrupt unconditionally.
This prevents hanging of the touchscreen in case of bogus interrupt
occurence.
Signed-off-by: Pavel Revak <palo@bielyvlk.sk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables ADC filtering on UCB1400 codec by default. The
benefit from this change is mostly on some Colibri boards where
the ADCSYNC pin of the UCB1400 codec isn't connected causing the
touchscreen to jitter very badly. This change has no visible
effect on boards where the ADCSYNC pin is connected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Palo Revak <palo@bielyvlk.sk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is the driver for Sentelic Finger Sensing Pad which can be found
on MSI WIND Netbook.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The KEY_MAX change in 2.6.28 changed the values of the JSIOCSBTNMAP and
JSIOCGBTNMAP constants; software compiled with the old values no longer
works with kernels following 2.6.28, because the ioctl switch statement
no longer matches the values given by the software. This patch handles
these ioctls independently of the length of data specified, and applies the
same treatment to JSIOCSAXMAP and JSIOCGAXMAP which currently depend on
ABS_MAX.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds a struct eeti_ts_platform_data which currently holds only one
value to specify the interrupt polarity.
The driver has a fallback if no platform data is passed in via the
i2c_board_info, so no regression is caused.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also have the driver send MSC_SCAN events as most keyboards do to aid
in updating keymap from userspace.
Tested-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add keypad driver for the 4x4 keypad on an evaluation board based
on w90p910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
hil_kbd and hil_ptr look like twins so it makes sense to combine them
into a single driver.
[deller@gmx.de: add MODULE_ALIAS() entry for mouse]
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Rename functions and variables from [hil_]kbd to [hil_]dev in
preparation of merging hil_kbd and hil_ptr.
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove assumption on the shift and size of rows/columns form
matrix_keypad driver.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Prestigio 157, an old no-name clone laptop uses input keys very
similar to the Wistron 1557/MS2141 with the addition of BIOS-controlled
wireless radio frequency kill switch.
This patch adds support for the RF kill switch control and adds manual
identification of the model.
The Prestigio does not expose any recognisable identity via dmidecode
and so requires manual selection at module init using
force=1 keymap=prestigio
Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The OLPC XO laptop incorporates a combination touchpad/tablet device
which unfortunately requires frequent recalibration. The driver will
force this automatically when various suspicious behaviors are
observed, and the user can recalibrate manually (with a special
keyboard sequence). There's currently no way, however, for an external
program to cause recalibration. We can not use the reconnect
capability which is already available in /sys because full reset of
the touchpad takes 1.1 - 1.2 secons which is too long.
This patch creates a new node in /sys which, when written with '1',
will force a touchpad recalibration; no other writes (or reads)
of this node are supported.
Signed-off-by: Paul Fox <pgf@laptop.org>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The synaptic touchpad on the Asus G1S is not properly detected when
rebooting machine or on cold boot from time to time. Adding the Asus
G1S to the noloop exception table resolves the issue.
# dmidecode 2.10
SMBIOS 2.4 present.
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: G1S
Version: 1.0
Wake-up Type: Power Switch
SKU Number:
Family:
Signed-off-by: Jory A. Pratt <geekypenguin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Check the result when sending the power down command to the controller.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In cases when get_pendown_state callback is not available have
the driver to fallback on pressure calculation to determine if
the pen is up.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the e2i touchscreen controller used in the
Mimo 740 (and probably in other e2i touchscreen products). Tested on
Mimo 740.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't read coordinates during probe of the driver, just power down
the controller and wait for interrupts.
Signed-off-by: Richard Röjfors<richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make init_platform_hw and exit_platform_hw callbacks optional since
they are not needed on all platforms.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Properly shut off interrupts/delayed work by free-ing IRQ first
and then ensuring that enable/disable is balanced. Also add
__devinit/__devexit markings, restore poll delay/period scheduling
logic, make sure we call exit_platform_hw() method when probe
fails.
Tested-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since it's not allowed to do synchronous I2C in the HR timer callback
context we have to switch to using the global workqueue. The work is
scheduled every 1ms when polling rather than 5 us.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
clk_disable() in remove method is not needed since we already
have clk_disable in pxa27x_keypad_close().
Also make sure the driver uses resource_size() and helpers from
include/input/matrix_keypad.h
Tested-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch allows tweaking the behaviour of GPIO_STATUS register
shift quirk that's in wm97xx-core. The problem with GPIO_STATUS
register being shifted by one doesn't appear on all hardware it
seems and causes problems with accelerated touchscreen drivers on
Palm hardware. Therefore an accelerated touchscreen driver can select
if the shift is/isn't happening on the hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch refactors the Mainstone accelerated touch code a little and
adds support for interrupt driven touchscreen on Palm LifeDrive, TX and
Tungsten T5.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov