Avoid full checksum calculation for apps that can provide
info whether csum was broken after payload mangling. For now only
ip_vs_ftp mangles payload and it updates the csum, so the full
recalculation is avoided for all packets.
Add CHECKSUM_UNNECESSARY for snat_handler (TCP and UDP).
It is needed to support SNAT from local address for the case
when csum is fully recalculated.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
IPv6 encapsulation uses a bad source address for the tunnel.
i.e. VIP will be used as local-addr and encap. dst addr.
Decapsulation will not accept this.
Example
LVS (eth1 2003::2:0:1/96, VIP 2003::2:0:100)
(eth0 2003::1:0:1/96)
RS (ethX 2003::1:0:5/96)
tcpdump
2003::2:0:100 > 2003::1:0:5: IP6 (hlim 63, next-header TCP (6) payload length: 40) 2003::3:0:10.50991 > 2003::2:0:100.http: Flags [S], cksum 0x7312 (correct), seq 3006460279, win 5760, options [mss 1440,sackOK,TS val 1904932 ecr 0,nop,wscale 3], length 0
In Linux IPv6 impl. you can't have a tunnel with an any cast address
receiving packets (I have not tried to interpret RFC 2473)
To have receive capabilities the tunnel must have:
- Local address set as multicast addr or an unicast addr
- Remote address set as an unicast addr.
- Loop back addres or Link local address are not allowed.
This causes us to setup a tunnel in the Real Server with the
LVS as the remote address, here you can't use the VIP address since it's
used inside the tunnel.
Solution
Use outgoing interface IPv6 address (match against the destination).
i.e. use ip6_route_output() to look up the route cache and
then use ipv6_dev_get_saddr(...) to set the source address of the
encapsulated packet.
Additionally, cache the results in new destination
fields: dst_cookie and dst_saddr and properly check the
returned dst from ip6_route_output. We now add xfrm_lookup
call only for the tunneling method where the source address
is a local one.
Signed-off-by:Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch allows to listen to events that inform about
expectations destroyed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The ebt_ip6.h and ebt_nflog.h headers are not not known to Kbuild and
therefore not installed by make headers_install. Fix that up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Many of the used macros are just there for userspace compatibility.
Substitute the in-kernel code to directly use the terminal macro
and stuff the defines into #ifndef __KERNEL__ sections.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Forgot to add xt_log.h in commit a8defca0 (netfilter: ipt_LOG:
add bufferisation to call printk() once)
Signed-off-by: Patrick McHardy <kaber@trash.net>
The functions nf_nat_proto_find_get and nf_nat_proto_put are
only used internally in nf_nat_core. This might break some out
of tree NAT module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Allow the persistence engine of a virtual service to be set, edited
and unset.
This feature only works with the netlink user-space interface.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
This shouldn't break compatibility with userspace as the new data
is at the end of the line.
I have confirmed that this doesn't break ipvsadm, the main (only?)
user-space user of this data.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
This patch adds the basic infrastructure to support user-space
expectation helpers via ctnetlink and the netfilter queuing
infrastructure NFQUEUE. Basically, this patch:
* adds NF_CT_EXPECT_USERSPACE flag to identify user-space
created expectations. I have also added a sanity check in
__nf_ct_expect_check() to avoid that kernel-space helpers
may create an expectation if the master conntrack has no
helper assigned.
* adds some branches to check if the master conntrack helper
exists, otherwise we skip the code that refers to kernel-space
helper such as the local expectation list and the expectation
policy.
* allows to set the timeout for user-space expectations with
no helper assigned.
* a list of expectations created from user-space that depends
on ctnetlink (if this module is removed, they are deleted).
* includes USERSPACE in the /proc output for expectations
that have been created by a user-space helper.
This patch also modifies ctnetlink to skip including the helper
name in the Netlink messages if no kernel-space helper is set
(since no user-space expectation has not kernel-space kernel
assigned).
You can access an example user-space FTP conntrack helper at:
http://people.netfilter.org/pablo/userspace-conntrack-helpers/nf-ftp-helper-userspace-POC.tar.bz
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
With this patch, you can specify the expectation flags for user-space
created expectations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add new sysctl flag "snat_reroute". Recent kernels use
ip_route_me_harder() to route LVS-NAT responses properly by
VIP when there are multiple paths to client. But setups
that do not have alternative default routes can skip this
routing lookup by using snat_reroute=0.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add more code to IPVS to work with Netfilter connection
tracking and fix some problems.
- Allow IPVS to be compiled without connection tracking as in
2.6.35 and before. This can avoid keeping conntracks for all
IPVS connections because this costs memory. ip_vs_ftp still
depends on connection tracking and NAT as implemented for 2.6.36.
- Add sysctl var "conntrack" to enable connection tracking for
all IPVS connections. For loaded IPVS directors it needs
tuning of nf_conntrack_max limit.
- Add IP_VS_CONN_F_NFCT connection flag to request the connection
to use connection tracking. This allows user space to provide this
flag, for example, in dest->conn_flags. This can be useful to
request connection tracking per real server instead of forcing it
for all connections with the "conntrack" sysctl. This flag is
set currently only by ip_vs_ftp and of course by "conntrack" sysctl.
- Add ip_vs_nfct.c file to hold all connection tracking code,
by this way main code should not depend of netfilter conntrack
support.
- Return back the ip_vs_post_routing handler as in 2.6.35 and use
skb->ipvs_property=1 to allow IPVS to work without connection
tracking
Connection tracking:
- most of the code is already in 2.6.36-rc
- alter conntrack reply tuple for LVS-NAT connections when first packet
from client is forwarded and conntrack state is NEW or RELATED.
Additionally, alter reply for RELATED connections from real server,
again for packet in original direction.
- add IP_VS_XMIT_TUNNEL to confirm conntrack (without altering
reply) for LVS-TUN early because we want to call nf_reset. It is
needed because we add IPIP header and the original conntrack
should be preserved, not destroyed. The transmitted IPIP packets
can reuse same conntrack, so we do not set skb->ipvs_property.
- try to destroy conntrack when the IPVS connection is destroyed.
It is not fatal if conntrack disappears before that, it depends
on the used timers.
Fix problems from long time:
- add skb->ip_summed = CHECKSUM_NONE for the LVS-TUN transmitters
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Patrick McHardy <kaber@trash.net>
- the sync protocol supports 16 bits only, so bits 0..15 should be
used only for flags that should go to backup server, bits 16 and
above should be allocated for flags not sent to backup.
- use IP_VS_CONN_F_DEST_MASK as mask of connection flags in
destination that can be changed by user space
- allow IP_VS_CONN_F_ONE_PACKET to be set in destination
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Patrick McHardy <kaber@trash.net>
commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).
Problem is that following sequence :
fd = socket(...)
connect(fd, &remote, ...)
not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)
Sequence is :
- autobind() : choose a random local port, insert socket in hash tables
[while local address is INADDR_ANY]
- connect() : set remote address and port, change local address to IP
given by a route lookup.
When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.
One solution to this problem is to rehash datagram socket if needed.
We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.
This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace e.g. u_int32_t types with the more common uint32_t.
Reported-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Also, a number of changes were made based on the assumption that
rds.h wasn't exported, so roll these back.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Add two CMSGs for masked versions of cswp and fadd. args
struct modified to use a union for different atomic op type's
arguments. Change IB to do masked atomic ops. Atomic op type
in rds_message similarly unionized.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Add a flag to the API so users can indicate they want
silent operations. This is needed because silent ops
cannot be used with USE_ONCE MRs, so we can't just
assume silent.
Also, change send_xmit to do atomic op before rdma op if
both are present, and centralize the hairy logic to determine if
we want to attempt silent, or not.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Implement a CMSG-based interface to do FADD and CSWP ops.
Alter send routines to handle atomic ops.
Add atomic counters to stats.
Add xmit_atomic() to struct rds_transport
Inline rds_ib_send_unmap_rdma into unmap_rm
Signed-off-by: Andy Grover <andy.grover@oracle.com>
We use rcu_dereference_check(p, rcu_read_lock_held() ||
lockdep_rtnl_is_held()) several times in network stack.
More usages to come too, so its time to create a helper.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Do not create expectation when forwarding the PORT
command to avoid blocking the connection. The problem is that
nf_conntrack_ftp.c:help() tries to create the same expectation later in
POST_ROUTING and drops the packet with "dropping packet" message after
failure in nf_ct_expect_related.
- Change ip_vs_update_conntrack to alter the conntrack
for related connections from real server. If we do not alter the reply in
this direction the next packet from client sent to vport 20 comes as NEW
connection. We alter it but may be some collision happens for both
conntracks and the second conntrack gets destroyed immediately. The
connection stucks too.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix a mismatch between code and comment
percpu: fix a memory leak in pcpu_extend_area_map()
percpu: add __percpu notations to UP allocator
percpu: handle __percpu notations in UP accessors
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix tty_line must not be equal to number of allocated tty pointers in tty driver
serial: bfin_sport_uart: restore transmit frame sync fix
serial: fix port type conflict between NS16550A & U6_16550A
MAINTAINERS: orphan isicom
vt: Fix console corruption on driver hand-over.
Sandybridge GTT has new cache control bits in PTE, which controls
graphics page cache in LLC or LLC/MLC, so we need to extend the mask
function to respect the new bits.
And set cache control to always LLC only by default on Gen6.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
cgroup_attach_task_current_cg API that have upstream is backwards: we
really need an API to attach to the cgroups from another process A to
the current one.
In our case (vhost), a priveledged user wants to attach it's task to cgroups
from a less priveledged one, the API makes us run it in the other
task's context, and this fails.
So let's make the API generic and just pass in 'from' and 'to' tasks.
Add an inline wrapper for cgroup_attach_task_current_cg to avoid
breaking bisect.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Bug seen by Dr. David Alan Gilbert with sparse
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dave reported an rcu lockdep warning on 2.6.35.4 kernel
task->cgroups and task->cgroups->subsys[i] are protected by RCU.
So we avoid accessing invalid pointers here. This might happen,
for example, when you are deref-ing those pointers while someone
move @task from one cgroup to another.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct state range of PHY bus addresses (i.e. 0-31) in comment,
make spelling of PHY consistent in comments.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- napi_gro_flush() is exported from net/core/dev.c, to avoid
an irq_save/irq_restore in the packet receive path.
- use napi_gro_receive() instead of netif_receive_skb()
- use napi_gro_flush() before calling __napi_complete()
- turn on NETIF_F_GRO by default
- Tested on a Marvell 88E8001 Gigabit NIC
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov