The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
This patch adds runtime power management support for otg fsm mode, since
A-device in a_idle state cannot detect data pulse irq after suspended, here
enable wakeup by connection before suspend to make it can be resumed by DP;
and handle wakeup from that state like SRP.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define ci_get_revision API to know the controller revision
information according to chipidea 1.1a, 2.0a and 2.5a spec.
Besides, add one entry at struct ci_hdrc to indicate revision
information, it can be used for adding different code for
revisions, eg kinds of errata.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds OTG fsm timers initialization, which use controller's 1ms
interrupt as timeout counter, also adds some local timers which are not
in otg_fsm_timer list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to set the chipidea udc into full-speed only mode.
It is set by the oftree property "maximum-speed = full-speed".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to let the PHY enter/leave low power mode.
Before the controller going to work(at probe/resume), it needs to let
the PHY leave low power mode.
After the controller stopping working(at remove/suspend), it needs to
let the PHY enter low power mode to save power consumption.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file is mainly used to access otgsc currently, it may
add otg related things in the future.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following build warnings on x86:
drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to configure the PTW, PTS and STS bits
inside the portsc register for host and device mode before the driver
starts and the phy can be addressed as hardware implementation is
designed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds EHCI host support to the chipidea driver. We want it to be
part of the hdrc driver and not a standalone (sub-)driver module, as
the structure of ehci-hcd.c suggests, so for chipidea controller we
hack it to not provide platform-related code, but only the ehci hcd.
The ehci-platform driver won't work for us here too, because the
controller uses the same registers for both device and host mode and
also otg-related bits, so it's not really possible to put ehci registers
into a separate resource.
This is not a pretty solution, but the alternative is exporting symbols
from the chipidea driver to a ehci-chipidea driver and doing all the
module refcounting.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the bits of USBMODE register are defined in <usb/ehci_def.h>,
use them instead of having our own definitions.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add some generic code for roles and implement simple role switching
based on ID pin state and/or a sysfs file. At this, we also rename
the device to ci_hdrc, which is what it is.
The "manual" switch is made into a sysfs file and not debugfs, because
it might be useful even in non-debug context. For some boards, like
sheevaplug, it seems to be the only way to switch roles without modifying
the hardware, since the ID pin is always grounded.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen