- moves out of nouveau_bios.c and demagics the logical state definitions
- simplifies chipset-specific driver interface
- makes most of gpio irq handling common, will use for nv4x hpd later
- api extended to allow both direct gpio access, and access using the
logical function states
- api extended to allow for future use of gpio extender chips
- pre-nv50 was handled very badly, the main issue being that all GPIOs
were being treated as output-only.
- fixes nvd0 so gpio changes actually stick, magic reg needs bashing
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't need more than the line id to determine the PWM controller, and
the GPIO interfaces are about to change somewhat.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More work needs to be done on supporting the different memory types.
v2 (Ben Skeggs):
- fixed up conflicts from not having pausing patch first
- restructured code somewhat to fit with how all the other code works
- fixed bug where incorrect mpll_ctrl could get set sometimes
- removed stuff that's cargo-culted from the binary driver
- merged nv92+ display disable into hwsq
- fixed incorrect opcode 0x5f magic at end of ucode
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DCB table provided by the VBIOS on most MXM chips has a number of
entries which either need to be disabled, or modified according to the
MXM-SIS Output Device Descriptors.
The x86 vbios code usually takes care of this for us, however, with the
large number of laptops now with switchable graphics or optimus, a lot
of the time nouveau is responsible for POSTing the card instead - leaving
some fun situations like, plugging in a monitor and having nouveau decide
3 connectors actually just got plugged in..
No MXM-SIS fetching methods implemented yet.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Another case where we parsed vbios data to some structs, then again use
that info once to construct another set of data. Skip the intermediate
step.
This is also slightly improved in that we can now use DCB 3.x connector
table info, which will allow NV4x to gain hotplug support, and to make
quirks for SPWG LVDS panels unnecessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
i2c-algo-bit doesn't actually work very well on one card I have access to
(NVS 300), random single-bit errors occur most of the time - what we're
doing now is closer to what xf86i2c.c does.
The original plan was to figure out why i2c-algo-bit fails on the NVS 300,
and fix it. However, while investigating I discovered i2c-algo-bit calls
cond_resched(), which makes it a bad idea for us to be using as we execute
VBIOS scripts from a tasklet, and there may very well be i2c transfers as
a result.
So, since I already wrote this code in userspace to track down the NVS 300
bug, and it's not really much code - lets use it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Was using nv_mask, which is bad. Reading the reg senses the current line
states, which aren't necessarily the states we're trying to drive the
lines to.
Fixed to store SCL driver state just as we already do for SDA.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not much point parsing the vbios data into a struct which is only used once
to parse the data into another struct, go directly from vbios to
nouveau_i2c_chan.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This primary reason for this was mostly to avoid duplication of some of
this stuff by the MXM-SIS parser. However, some other cleanups will also
follow this as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Spotted while messing with overlay channels (probably as a result of
sending a similar "disable" sequence as we do for the flip channels).
The value in 0x61008c was 0x20, which one would reasonably guess is
"bit 5 == something to report about evo channel 5" - but who knows.
Spotted the binary driver getting this too, and it appears to not do
anything exciting as a result. So, handle it the same way and avoid
an IRQ storm.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pre-nva3 will likely require far more extensive setup, and nvd9 needs to
be checked to find its SOR_HDMI/SOR_AUDIO blocks.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
read_pll_ref() needs to take into account the refclk src bits in 0xc040 on
some chipsets, it wasn't doing this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This area is horrifically complicated on these chipsets, and it's likely we
will need at least a few more tweaks yet.
Oh yes, and it's completely disabled on IGPs for the moment. From traces,
things look potentially different there yet again. Sigh...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Following to "drm/nv50/pm: s/unk05/vdec/", let's rename the PLL to PLL_VDEC
PLL names are purely indicative and are based on the most important engine
it clocks.
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reporting an error is better than silently refusing to reclock.
V2: Use the same logic on nv40
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes a case where we don't get separate supervisor interrupt sequences for
disconnect and modeset events.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should fix issues with kexec, and as a nice side bonus, the code to avoid
having PDISP disappear will also fix hibernate on those effected systems.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This has the effect of ensuring the encoders which were active before we
loaded get disconnected properly before we start reprogramming them.
Also removing a bit of cargo-cult from the initial evo pushbuf.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
PDISP doesn't like it when disabled CRTCs are poked.
Fixes external output not coming to life when it has cursor on.
https://bugs.freedesktop.org/show_bug.cgi?id=41608
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Otherwice code that responsible for idling the card can't work.
BIOS init tables are supposed to init the clocks to correct values,
so that shouldn't cause any problems (we don't reclock by default anyway)
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Because doing polling while hardware is disabled is a bad idea...
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Exposes the same connector properties as the Radeon implementation, however
their behaviour isn't exactly the same. The primary difference being that
unless both hborder/vborder have been defined by the user, the driver will
keep the aspect ratio of the overscanned area the same as the mode the
display is programmed for.
Enabled for digital outputs on GeForce 8 and up, excluding GF119.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A NV49 appeared a while back that was using the "nv41 style" pwm registers,
rather than the "nv40 style" ones my board is using. This disproves the
previous theory that the pwm controller choice is chipset-specific.
So, after looking at a bunch of vbios images it appears that the next viable
theory is that we should select the pwm controller to use based on the gpio
line the fan is tied to, just like we do on nv50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The handling of the internal pwm fan controller is similar enough between
current chipsets that it makes sense to share the logic, and bugfixes :)
No hw backends converted yet, will automatically fall-through to the
"old" per-chipset fanspeed hooks for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Exposes the following sysfs entries:
- fan0_input: read the rotational speed of the fan (poll a bit during 250ms)
- pwm0: set the pwm duty cycle
- pwm0_min/max: set the minimum/maximum pwm value
v2 (Ben Skeggs):
- nv50 pwm controller code removed in favour of other more complete code
- FAN_RPM -> FAN_SENSE
- merged FAN_SENSE readout into common code, not at all nv50-specific
- protected fanspeed changes with perflvl_wr
- formatting tidying
- added some comments where things are shaky
v3 (Martin Peres)
- ensure duty min/max from thermal table are sane
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
The exynos fimd supports 5 window overlays. Only one window overlay of
fimd is used by the crtc, so we need plane feature to use the rest
window overlays.
This creates one ioctl exynos specific - DRM_EXYNOS_PLANE_SET_ZPOS, it
is the ioctl to decide for user to assign which window overlay.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This adds runtime PM feature for fimd. The runtime PM functions control
clocks for fimd and prevent to access the register of fimd for vblank
when clock is turned off by suspend of runtime PM.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
With DPMS ON and OFF requests, crtc dpms would be in charge of
just only device power such as fimd or hdmi and encoder dpms
in charge of device setting(mode setting and register updating)
and also lcd panel and digital TV power.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The exynos drm also should use struct drm_mode_fb_cmd2 by changes of
308e5bcbdb commit(drm: add an fb creation
ioctl that takes a pixel format v5).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This compile errors occur by changes of
e08e96de98 commit, so exynos drm should
apply this changes.
CC drivers/gpu/drm/exynos/exynos_drm_drv.o
drivers/gpu/drm/exynos/exynos_drm_drv.c:185: warning: braces around scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:185: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: warning: initialization from incompatible pointer type
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: warning: (near initialization for 'exynos_drm_driver.fops')
make[4]: *** [drivers/gpu/drm/exynos/exynos_drm_drv.o] Error 1
make[3]: *** [drivers/gpu/drm/exynos] Error 2
make[2]: *** [drivers/gpu/drm] Error 2
make[1]: *** [drivers/gpu] Error 2
make: *** [drivers] Error 2
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This function returns the number of planes used by a specific pixel
format.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call connector->funcs->dpms(DPMS_ON) rather than just setting
connector->dpms = DPMS_ON. This ensures that if the connector
has something to do to enable the output (rather than just using
drm_helper_connector_dpms helper directly), that this happens
at bootup. This solves an issue with connectors not getting
enabled from fbcon_init() when the driver is loaded.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the bpc is set from the connector is 0, we then use it later to adjust
in a special case the HDMI pixel clock, however if the bpc is 0, we end up
passing a 0 pixel clock into the code.
I'm not sure if this is the correct answer or if we should avoid the HDMI
clock adjustment for 0 values.
This fixes a divide by 0 on my Llano system with a HDMI monitor and hdmi
audio enabled.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Somewhat specializaed sub-allocator designed to perform sub-allocation
for command buffer not only for current cs ioctl but for future command
submission ioctl as well. Patch also convert current ib pool to use
the sub allocator. Idea is that ib poll buffer can be share with other
command buffer submission not having 64K granularity.
v2 Harmonize pool handling and add suspend/resume callback to pin/unpin
sa bo (tested on rv280, rv370, r420, rv515, rv610, rv710, redwood, cayman,
rs480, rs690, rs880)
v3 Simplify allocator
v4 Fix radeon_ib_get error path to properly free fence
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
cayman is wb only and doesn't have a VC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some rptr/wptrs fields have different offsets and not all rings are pm4
so add a new nop field.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also test multiple waits on the same semaphore.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a start fence driver helper function which will be call
once for each ring and will compute cpu/gpu addr for fence
depending on wether to use wb buffer or scratch reg.
This patch replace initialize fence driver separately which
was broken in regard of GPU lockup. The fence list for created,
emited, signaled must be initialize once and only from the
asic init callback not from the startup call back which is
call from the gpu reset.
v2: With this in place we no longer need to know the number of
rings in fence_driver_init, also writing to the scratch reg
before knowing its offset is a bad idea.
v3: rebase on top of change to previous patch in the serie
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Those debugfs files aren't r600 specific, so they
shouldn't be in r600.c. Move them to radeon_ring.c
and also add functionality to dump CP1 & CP2 ring
informations.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
That naming seems to make more sense, since we not
only want to run PM4 rings with it.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Disable the additional compute rings on cayman
until their setup is fully implemented.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Split counting of emited fences out of power
management into a seperate function.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Emitting fences, semaphores and ib works differently
on different ring, so its is easier to maintain
separate functions for each ring.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tests syncing between all rings by using
semaphores and fences.
v2: use radeon_testing as a bit flag rather than on/off switch
this allow to test for one thing at a time (bo_move or semaphore
test). It kind of break the usage if user wheren't using 1
for bo move test but as it's a test feature i believe it's ok.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace cp, cp1 and cp2 members with just an array
of radeon_cp structs.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Every ring seems to have the concept of read and
write pointers. Make the register offset variable
so we can use the functions for different types of rings.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Give all asic and radeon_ring_* functions a
radeon_cp parameter, so they know the ring to work with.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They are used to sync between rings, while fences
sync between a ring and the cpu.
v2 Fix radeon_semaphore_driver_fini when no semaphore were
allocated.
v3 Initialize list early on to avoid issue in case or early
error
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For supporting multiple CP ring buffers, async DMA
engines and UVD. We still need a way to synchronize
between engines.
v2 initialize unused fence driver ring to avoid issue in
suspend/unload
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Better fix it before this obvious typo spreads even more.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only check the previously checked relocs for
duplicates. Also leaving the handle uninitialized
isn't such a good idea.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having registered debugfs files globally causes
the files to not show up on the second, third
etc.. card in the system.
v2: fix crash on module unloading
v3: fix space indentation
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GCT setup was used on Moorestown. The Oaktrail version uses a normal PC
interface. That means we must also honour the dither info from the BIOS
data.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The move to connectors breaks Oaktrail again if we have memory poisoning
enabled. Fix this.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge in the upstream tree to bring in the mainline fixes.
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/nouveau_sgdma.c
This switches the ifdef to match the Kconfig so that Oaktrail probing occurs
and adds some additional minor bulletproofing.
Tested on a Fujtisu Stylistic Q550 internal display. HDMI might work but that
remains to be seen.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We currently don't have support for parsing SDVO mappings from BIOS so we're
guessing the bus switch parameter. This isn't working so hardcode it to a
configuration known to work on most poulsbo hardware.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace psb_intel_output with psb_intel_encoder and psb_intel_connector
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
[Changed Moorestown reference to Oaktrail]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace psb_intel_output with psb_intel_encoder and psb_intel_connector.
Things will need to be cleaned up and tested so consider this an initial
patch for Cedarview.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Our current SDVO implementation is not working properly, so replace it with
a modified version of the i915. Further testing and debugging is needed to make
sure we can handle the different SDVO setups and wiring.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before we integrate the new SDVO code we need GMBUS support
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
LVDS for PSB now uses psb_intel_encoder and psb_intel_connectors instead of
psb_intel_output. i2c_bus and ddc_bus are moved to lvds_priv. There was also a
pointer to mode_dev (for no obvious reason) that we now get directly from
dev_priv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix cases where we need to know what encoder type is behind a given connector.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
First step towards adding i915 alike encoder and connector abstractions. This
will make life easier when adding i915 output code into our driver. It also
removes the old psb_intel_output struct.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise each driver would need to keep the information inside
their own framebuffer object structure. Also add offsets[]. BOs
on the other hand are driver specific, so those can be kept in
driver specific structures.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Help drivers a little by guaranteeing that crtc_x+crtc_w and
crtc_y+crtc_h don't overflow.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure the source coordinates stay within the buffer.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are the only indication to user space that the plane was disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Several pointers and casts were missing __user annotations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unlock the mode_config mutex if drm_plane_init() fails.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My EFI BIOS starts the graphics card up in my projector's preferred EDID
mode, 1080@60i. The Intel driver does not clear all the interlaced bits.
This patch introduces a new PIPECONF_INTERLACE_MASK define and uses it
to restore progressive mode.
Signed-of-by: Christian Schmidt <schmidt@digadd.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current logic misunderstands the spec about CEA 18byte descriptors.
First, the spec doesn't state "detailed timing descriptors" but "18 byte
descriptors", so any data record could be stored, mixed timings and
other data, just as in the standard EDID.
Second, the lower four bit of byte 3 of the CEA record do not contain
the number of descriptors, but "the total number of DTDs defining native
formats in the whole EDID [...], starting with the first DTD in the DTD
list (which starts in the base EDID block)." A device can of course
support non-native formats.
As such the number can't be used to determine n, and the existing code
will filter non-timing 18byte descriptors anyway.
Signed-off-by: Christian Schmidt <schmidt@digadd.de>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
CEA datablocks are only defined from revision 3 onwards. Only check for
them if the revision says so.
Signed-of-by: Christian Schmidt <schmidt@digadd.de>
Tested-by: James Cloos <cloos@jhcloos.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise hangcheck spuriously fires when running blitter/bsd-only
workloads.
Contrary to a similar patch by Ben Widawsky this does not check
INSTDONE of the other rings. Chris Wilson implied that in a failure to
detect a hang, most likely because INSTDONE was fluctuating. Thus only
check ACTHD, which as far as I know is rather reliable. Also, blitter
and bsd rings can't launch complex tasks from a single instruction
(like 3D_PRIM on the render with complex or even infinite shaders).
This fixes spurious gpu hang detection when running
tests/gem_hangcheck_forcewake on snb/ivb.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
On DP monitor hot remove, clear DP_AUDIO_OUTPUT_ENABLE accordingly,
so that the audio driver will receive hot plug events and take action
to refresh its device state and ELD contents.
Note that the DP_AUDIO_OUTPUT_ENABLE bit may be enabled or disabled
only when the link training is complete and set to "Normal".
Tested OK for both hot plug/remove and DPMS on/off.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On HDMI monitor hot remove, clear SDVO_AUDIO_ENABLE accordingly, so that
the audio driver will receive hot plug events and take action to refresh
its device state and ELD contents.
The cleared SDVO_AUDIO_ENABLE bit needs to be restored to prevent losing
HDMI audio after DPMS on.
CC: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ELD may or may not change when switching the video mode.
If unchanged, don't trigger hot plug events to HDMI audio driver.
This avoids disturbing the user with repeated printks.
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Change the definitions from GEN5 to IBX as they aren't in the CPU and
some SNB systems actually shipped with IBX chipsets (or, at least that's
a supported configuration).
The GEN7_* register addresses actually take effect since GEN6 and should
be prefixed by CPT, the PCH code name.
Suggested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
SandyBridge should be using the same register addresses as IvyBridge.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Doesn't protect any error code and only gets in the way of debugging.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver implements the needed resource management required
to use that register.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit eb1711bb94.
It blows up the i915 seqno tracking, resulting in the
BUG_ON(seqno == 0);
in i915_wait_request() triggering, which will cause lock-ups.
See for example
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/903010https://lkml.org/lkml/2011/12/14/395
Reported-requested-and-tested-by: Dirk Hohndel <dirk@hohndel.org>
Reported-by: Richard Eames <Richard.Eames@flinders.edu.au>
Reported-by: Rocko Requin <rockorequin@hotmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
drm/i915/dp: Dither down to 6bpc if it makes the mode fit
drm/i915: enable semaphores on per-device defaults
drm/i915: don't set unpin_work if vblank_get fails
drm/i915: By default, enable RC6 on IVB and SNB when reasonable
iommu: Export intel_iommu_enabled to signal when iommu is in use
drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
drm/i915: prevent division by zero when asking for chipset power
drm/i915: add PCH info to i915_capabilities
drm/i915: set the right SDVO transcoder for CPT
drm/i915: no-lvds quirk for ASUS AT5NM10T-I
drm/i915: Treat pre-gen4 backlight duty cycle value consistently
drm/i915: Hook up Ivybridge eDP
drm/i915: add multi-threaded forcewake support
Some active adaptors (VGA usually) only have two lanes at 2.7GHz.
That's a maximum pixel clock of 144MHz at 8bpc, but 192MHz at 6bpc.
Fixes Asus UX31 panel being black at startup due to no valid modes since
dc22ee6fc1.
v2: Rebased to current code, resulting in the fix applying to EDP panels as
well. Also changed from spatio-temporal to just spatial dithering on
pre-ironlake, to be conssitent (and less visual flicker)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This adds a default setting for semaphores parameter, and enables
semaphores by default on IVB.
For now, as semaphores interaction with VTd causes random issues on
SNB, we do not enable them by default. But they can still be enabled
via the semaphores=1 kernel parameter.
v2: enables semaphores on SNB when IO remapping is disabled, with base
on Keith Packard patch.
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Ben Widawsky <ben@bwidawsk.net>
CC: Keith Packard <keithp@keithp.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42696
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=40564
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38862
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This fixes a race where we may try to finish a page flip and decrement
the refcount even if our vblank_get failed and we ended up with a
spurious flip pending interrupt.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=34211.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
RC6 should always work on IVB, and should work on SNB whenever IO
remapping is disabled. RC6 never works on Ironlake. Make the default
value for the parameter follow these guidelines. Setting the value
to either 0 or 1 will force the specified behavior.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38567
Cc: Ted Phelps <phelps@gnusto.com>
Cc: Peter <pab1612@gmail.com>
Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz>
Cc: Andrew Lutomirski <luto@mit.edu>
We were checking whether the supplied edid matched the connector it was
read from. We do this in case a DDC read returns an EDID for another
device on a multifunction or otherwise interesting card. However, we
failed to include LVDS as a digital device and so rejecting an otherwise
valid EDID.
Fixes the detection of the secondary SDVO LVDS panel on the Libretto
W105.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=39216
Signed-off-by: Keith Packard <keithp@keithp.com>
This prevents an in-kernel division by zero which happens when we are
asking for i915_chipset_val too quickly, or within a race condition
between the power monitoring thread and userspace accesses via debugfs.
The issue can be reproduced easily via the following command:
while ``; do cat /sys/kernel/debug/dri/0/i915_emon_status; done
This is particularly dangerous because it can be triggered by
a non-privileged user by just reading the debugfs entry.
This issue was also found independently by Konstantin Belousov
<kostikbel@gmail.com>, who proposed a similar patch.
Reported-by: Konstantin Belousov <kostikbel@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
v2: add a CPT-specific macro, make code cleaner
v3: fix commit message
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41272
Cc: stable@kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recursion loop goes retire_requests->unbind->gpu_idle->retire_reqeusts.
Every time we go through this we need a
- active object that can be retired
- and there are no other references to that object than the one from
the active list, so that it gets unbound and freed immediately.
Otherwise the recursion stops. So the recursion is only limited by the
number of objects that fit these requirements sitting in the active list
any time retire_request is called.
Issue exercised by tests/gem_unref_active_buffers from i-g-t.
There's been a decent bikeshed discussion whether it wouldn't be
better to pass around a flag, but imo this is o.k. for such a limited
case that only supports a w/a.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42180
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson>
[ickle- we built better bikesheds, but this keeps the rain off for now]
Tested-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Seems like something got mis-merged here.
Noticed by kallisti5 on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we were calling back move_notify in error path when the
bo is returned to it's original position or when destroy the bo.
When destroying the bo set the new mem placement as NULL when calling
back in the driver.
Updating nouveau to deal with NULL placement properly.
v2: reserve the object before calling move_notify in bo destroy path
at that point ttm should be the only piece of code interacting
with the object so atomic_set is safe here.
v3: callback move notify only once the bo is in its new position
call move notify want swaping out the buffer
v4:- don't call move_notify when swapin out bo, assume driver should
do what is appropriate in swap notify
- move move_notify call back to ttm_bo_cleanup_memtype_use for
destroy path
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Provide helper function to compute the kernel memory size needed
for each buffer object. Move all the accounting inside ttm, simplifying
driver and avoiding code duplication accross them.
v2 fix accounting of ghost object, one would have thought that i
would have run into the issue since a longtime but it seems
ghost object are rare when you have plenty of vram ;)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Move dma data to a superset ttm_dma_tt structure which herit
from ttm_tt. This allow driver that don't use dma functionalities
to not have to waste memory for it.
V2 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
V3 Make sure page list is initialized empty
V4 typo/syntax fixes
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
If the card is capable of more than 32-bit, then use the default
TTM page pool code which allocates from anywhere in the memory.
Note: If the 'ttm.no_dma' parameter is set, the override is ignored
and the default TTM pool is used.
V2 use pci_set_consistent_dma_mask
V3 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
CC: Ben Skeggs <bskeggs@redhat.com>
CC: Francisco Jerez <currojerez@riseup.net>
CC: Dave Airlie <airlied@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
With the exception that we do not handle the AGP case. We only
deal with PCIe cards such as ATI ES1000 or HD3200 that have been
detected to only do DMA up to 32-bits.
V2 force dma32 if we fail to set bigger dma mask
V3 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
V4 add debugfs entry is swiotlb is active not only if we are
on dma 32bits only gpu
CC: Dave Airlie <airlied@redhat.com>
CC: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
In TTM world the pages for the graphic drivers are kept in three different
pools: write combined, uncached, and cached (write-back). When the pages
are used by the graphic driver the graphic adapter via its built in MMU
(or AGP) programs these pages in. The programming requires the virtual address
(from the graphic adapter perspective) and the physical address (either System RAM
or the memory on the card) which is obtained using the pci_map_* calls (which does the
virtual to physical - or bus address translation). During the graphic application's
"life" those pages can be shuffled around, swapped out to disk, moved from the
VRAM to System RAM or vice-versa. This all works with the existing TTM pool code
- except when we want to use the software IOTLB (SWIOTLB) code to "map" the physical
addresses to the graphic adapter MMU. We end up programming the bounce buffer's
physical address instead of the TTM pool memory's and get a non-worky driver.
There are two solutions:
1) using the DMA API to allocate pages that are screened by the DMA API, or
2) using the pci_sync_* calls to copy the pages from the bounce-buffer and back.
This patch fixes the issue by allocating pages using the DMA API. The second
is a viable option - but it has performance drawbacks and potential correctness
issues - think of the write cache page being bounced (SWIOTLB->TTM), the
WC is set on the TTM page and the copy from SWIOTLB not making it to the TTM
page until the page has been recycled in the pool (and used by another application).
The bounce buffer does not get activated often - only in cases where we have
a 32-bit capable card and we want to use a page that is allocated above the
4GB limit. The bounce buffer offers the solution of copying the contents
of that 4GB page to an location below 4GB and then back when the operation has been
completed (or vice-versa). This is done by using the 'pci_sync_*' calls.
Note: If you look carefully enough in the existing TTM page pool code you will
notice the GFP_DMA32 flag is used - which should guarantee that the provided page
is under 4GB. It certainly is the case, except this gets ignored in two cases:
- If user specifies 'swiotlb=force' which bounces _every_ page.
- If user is using a Xen's PV Linux guest (which uses the SWIOTLB and the
underlaying PFN's aren't necessarily under 4GB).
To not have this extra copying done the other option is to allocate the pages
using the DMA API so that there is not need to map the page and perform the
expensive 'pci_sync_*' calls.
This DMA API capable TTM pool requires for this the 'struct device' to
properly call the DMA API. It also has to track the virtual and bus address of
the page being handed out in case it ends up being swapped out or de-allocated -
to make sure it is de-allocated using the proper's 'struct device'.
Implementation wise the code keeps two lists: one that is attached to the
'struct device' (via the dev->dma_pools list) and a global one to be used when
the 'struct device' is unavailable (think shrinker code). The global list can
iterate over all of the 'struct device' and its associated dma_pool. The list
in dev->dma_pools can only iterate the device's dma_pool.
/[struct device_pool]\
/---------------------------------------------------| dev |
/ +-------| dma_pool |
/-----+------\ / \--------------------/
|struct device| /-->[struct dma_pool for WC]</ /[struct device_pool]\
| dma_pools +----+ /-| dev |
| ... | \--->[struct dma_pool for uncached]<-/--| dma_pool |
\-----+------/ / \--------------------/
\----------------------------------------------/
[Two pools associated with the device (WC and UC), and the parallel list
containing the 'struct dev' and 'struct dma_pool' entries]
The maximum amount of dma pools a device can have is six: write-combined,
uncached, and cached; then there are the DMA32 variants which are:
write-combined dma32, uncached dma32, and cached dma32.
Currently this code only gets activated when any variant of the SWIOTLB IOMMU
code is running (Intel without VT-d, AMD without GART, IBM Calgary and Xen PV
with PCI devices).
Tested-by: Michel Dänzer <michel@daenzer.net>
[v1: Using swiotlb_nr_tbl instead of swiotlb_enabled]
[v2: Major overhaul - added 'inuse_list' to seperate used from inuse and reorder
the order of lists to get better performance.]
[v3: Added comments/and some logic based on review, Added Jerome tag]
[v4: rebase on top of ttm_tt & ttm_backend merge]
[v5: rebase on top of ttm memory accounting overhaul]
[v6: New rebase on top of more memory accouting changes]
[v7: well rebase on top of no memory accounting changes]
[v8: make sure pages list is initialized empty]
[v9: calll ttm_mem_global_free_page in unpopulate for accurate accountg]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Move the page allocation and freeing to driver callback and
provide ttm code helper function for those.
Most intrusive change, is the fact that we now only fully
populate an object this simplify some of code designed around
the page fault design.
V2 Rebase on top of memory accounting overhaul
V3 New rebase on top of more memory accouting changes
V4 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
ttm_backend will only exist with a ttm_tt, and ttm_tt
will only be of interest when bound to a backend. Merge them
to avoid code and data duplication.
V2 Rebase on top of memory accounting overhaul
V3 Rebase on top of more memory accounting changes
V4 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
V5 make sure ttm is unbound before destroying, change commit
message on suggestion from Tormod Volden
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Use the ttm_tt pages array for pages allocations, move the list
unwinding into the page allocation functions.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
On failure we need to make sure the page we free has wb cache
attribute. Do this pas call the proper ttm page helper function.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
This field is not use by any of the driver just drop it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Split btw highmem and lowmem page was rendered useless by the
pool code. Remove it. Note further cleanup would change the
ttm page allocation helper to actualy take an array instead
of relying on list this could drasticly reduce the number of
function call in the common case of allocation whole buffer.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
This was never use in none of the driver, properly using userspace
page for bo would need more code (vma interaction mostly). Removing
this dead code in preparation of ttm_tt & backend merge.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Each of these error messages can be caused by a broken or malicious
userspace wanting to spam the dmesg with useless info. They're really
not worthy of DRM_DEBUG statements either; those are generally only
useful during bringup of new hardware or versions, and ought to be
removed before going upstream anyway.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we pull the right BIOS data out of the hat we need to use it when
doing our panel setup.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The Oaktrail platform does not use the GCT/VBT format that is used by the
Moorestowm (non PC legacy) equivalent device. It uses the BIOS tables which
means an opregion and the like.
The current code uses the wrong table which breaks things like the Fujitsu
q550 tablets. Fix the table usage as a first step.
The problem was found and diagnosed by Chia-I Wu
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we can't fit a page aligned display stride then it's not the end of the
world for a normal font, so try half a page and work down sizes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add support for GTT based scrolling. Instead of pushing bits around we simply
use the GTT to change the mappings. This provides us with a very fast way to
scroll the display providing we have enough memory to allocate on 4K line
boundaries. In practice this seems to be the case except for very big displays
such as HDMI, and the usual configurations are netbooks/tablets.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we are the console then a printk can hit us with a spin lock held (and
in fact the kernel will do its best to take the console printing lock).
In that case we cannot politely sleep when synching after an accelerated op
but must behave obnoxiously to be sure of getting the bits out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initial changes to get backlight behaviour we want and to fix backlight crashes
on suspend/resume paths.
[Note: on some boxes this will now produce a warning about the backlight, this
isn't a regression it's an unfixed but non harmful case I still need to nail]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
During the power split ups and work a chunk of code escaped into the
Poulsbo code path which it isn't for. On some devices such as the Dell
mini-10 this causes problems.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Convert the spaces within the accel_2d.c file to tabs in order to comply
with the coding style of the kernel.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
[Trimmed to subset relevant to current tree]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Chipset reports MSI capabilities for Poulsbo even though it isn't really there.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
First step in adding proper irq handling. We'll start with poulsbo support so
make sure other chips don't touch drm_irq_install().
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This isn't actually usable - we simply don't have the vmap space on a 32bit
system to do this stunt. Instead we will rely on the low level drivers
limiting the console resolution as before.
The real fix is for someone to write a page table aware version of the
framebuffer console blit functions. Good university student project
perhaps..
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't want this external in case someone adds more to the hardware. We
want it out of the ABI.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At this point we won't add an external set of definitions. We want to get
everything out before we admit to a public API beyond the standardised
ones.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are two issues in vmw_kms_update_layout_ioctl(). First, the
for loop forgets to index rects and only checks the first element.
Second, there is a potential integer overflow if userspace passes
in a large arg->num_outputs. The call to kzalloc() would allocate
a small buffer, leading to out-of-bounds read.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Disabling the CRTC by setting its framebuffer to NULL, as used by
drm_framebuffer_cleanup(), was failing to pass the current framebuffer
to the crtc_func->disable callback. This is because of the dance within
drm_crtc_helper_set_config to pass the new_fb (NULL in this case) to the
drm_crtc_helper_set_mode with the currently attached fb as a parameter.
drm_crtc_helper_set_mode treats this as a no-op and the encoder is still
enabled. And so the current fb is forgotten before the call to
drm_helper_disable_unused_functions.
This patch treats disabling the CRTC as a simple special case rather
than adding further complexity into the configuration logic.
This fixes a pin-leak of the fb bo on Xserver close.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Name the formats as DRM_FORMAT_X instead of DRM_FOURCC_X. Use consistent
names, especially for the RGB formats. Component order and byte order are
now strictly specified for each format.
The RGB format naming follows a convention where the components names
and sizes are listed from left to right, matching the order within a
single pixel from most significant bit to least significant bit.
The YUV format names vary more. For the 4:2:2 packed formats and 2
plane formats use the fourcc. For the three plane formats the
name includes the plane order and subsampling information using the
standard subsampling notation. Some of those also happen to match
the official fourcc definition.
The fourccs for for all the RGB formats and some of the YUV formats
I invented myself. The idea was that looking at just the fourcc you
get some idea what the format is about without having to decode it
using some external reference.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I am under the impression that it only makes sense to call the ATIF
method if the graphics device has an ACPI handle attached. So we could
skip the call altogether if there is no such handle.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the proper macro to issue the debugging message in
radeon_atif_call(). Otherwise we spam the log of many systems with a
message which looks like an error message of unknown origin, and could
thus confuse the user. Commit dc77de12dd
was a first step in this direction, but was not sufficient IMHO.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Avoid infinite loops waiting for surface updates if a GPU
reset happens while waiting for a page flip.
See:
https://bugs.freedesktop.org/show_bug.cgi?id=43191
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv50/disp: silence compiler warning
drm/nouveau: fix oopses caused by clear being called on unpopulated ttms
drm/nouveau: Keep RAMIN heap within the channel.
drm/nvd0/disp: fix sor dpms typo, preventing dpms on in some situations
drm/nvc0/gr: fix TP init for transform feedback offset queries
drm/nouveau: add dumb ioctl support
NFI why this only started appearing now. The use of the uninitialised var
can't actually happen, so perhaps my compiler just got stupider.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The entire RAMIN is allocated to be 'size', but the heap is
specified as 'base' + 'size' inside RAMIN, so it will overflow
past RAMIN by 'base' bytes on NV50+ and clobber other allocatons
unless it's size is adjusted.
Signed-off-by: Younes Manton <younes.m@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Without this, they return bytes written since the last update of
the offset, but we want the full offset.
Trace shows setting this on GPC[0]/TP[0] is enough.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit 308e5bcbdb ("drm: add an fb creation ioctl that takes a pixel
format v5") missed one spot needing to be fixed up in the __BIG_ENDIAN
case.
Fixes build error:
drivers/gpu/drm/radeon/radeon_fb.c: In function
'radeonfb_create_pinned_object':
drivers/gpu/drm/radeon/radeon_fb.c:144:18: error: 'struct drm_mode_fb_cmd2'
has no member named 'bpp'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fops field in drm_driver is a pointer to file_operations
struct, not embedded structure
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
psb_gfx.mod.c is a generated file and should not be
revision controlled
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For i945 and earlier chips, the backlight frequency value had the low
bit (of 16) fixed to zero. The Pineview code path handled this by just
exposing the backlight range as 15 bits while other chips had the
backlight range limited to 0 .. 0xfffe.
This patch makes everyone take the pineview code path, providing 15
bits of backlight duty cycle range which seems more than sufficient to
me.
Daniel Mack reported that writing 1 to bit 0 of the duty cycle
register was causing problems on his Samsung X20 notebook, even when
the duty cycle value was less than the maximum backlight value. (He
tried a value of 29749 with max_brightness of 29750). This patch never
writes a '1' to that bit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reported-and-tested-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org
The Ivybridge eDP control register looks like a cross between a
Cougarpoint PCH DP control register and a Sandybridge eDP control
register.
Where things trivially match, share the code. Where there are any
tricky bits, just split things out into two obviously separate code paths.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Fang Xun <xunx.fang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41991
On IVB C0+ with newer BIOSes, the forcewake handshake has changed. There's
now a bitfield for different driver components to keep the GT powered
on. On Linux, we centralize forcewake handling in one place, so we
still just need a single bit, but we need to use the new registers if MT
forcewake is enabled.
This needs testing on affected machines. Please reply with your
tested-by if you had problems after a BIOS upgrade and this patch fixes
them.
v2: force MT mode. shift by 16
v3: set MT force wake bits then check ECOBUS
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42923
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm: integer overflow in drm_mode_dirtyfb_ioctl()
drivers/gpu/vga/vgaarb.c: add missing kfree
drm/radeon/kms/atom: unify i2c gpio table handling
drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
ttm: Don't return the bo reserved on error path
drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
...
There is a potential integer overflow in drm_mode_dirtyfb_ioctl()
if userspace passes in a large num_clips. The call to kmalloc would
allocate a small buffer, and the call to fb->funcs->dirty may result
in a memory corruption.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Split the quirks and i2c_rec assignment into separate
functions used by both radeon_lookup_i2c_gpio() and
radeon_atombios_i2c_init(). This avoids duplicating code
and cases where quirks were only added to one of the
functions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes i2c test failures when i2c_algo_bit.bit_test=1.
The hw doesn't actually require a mask, so just set it
to the default mask bits for r1xx-r4xx radeon ddc.
I missed this part the first time through.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
An unlikely race could case a bo to be returned reserved on an error path.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux: (25 commits)
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
drm/i915: enable cacheable objects on Ivybridge
drm/i915: add constants to size fence arrays and fields
drm/i915: Ivybridge still has fences!
drm/i915: forcewake warning fixes in debugfs
drm/i915: Fix object refcount leak on mmappable size limit error path.
drm/i915: Use mode_config.mutex in ironlake_panel_vdd_work
...
This adds a new optional chunk to the CS ioctl that specifies optional flags
to the CS parser. Why this is useful is explained below. Note that some regs
no longer need the NOP relocation packet if this feature is enabled.
Tested on r300g and r600g with this flag disabled and enabled.
Assume there are two contexts sharing the same mipmapped tiled texture.
One context wants to render into the first mipmap and the other one
wants to render into the last mipmap. As you probably know, the hardware
has a MACRO_SWITCH feature, which turns off macro tiling for small mipmaps,
but that only applies to samplers.
(at least on r300-r500, though later hardware likely behaves the same)
So we want to just re-set the tiling flags before rendering (writing
packets), right? ... No. The contexts run in parallel, so they may
set the tiling flags simultaneously and then fire their command streams
also simultaneously. The last one setting the flags wins, the other one
loses.
Another problem is when one context wants to render into the first and
the last mipmap in one CS. Impossible. It must flush before changing
tiling flags and do the rendering into the smaller mipmaps in another CS.
Yet another problem is that writing copy_blit in userspace would be a mess
involving re-setting tiling flags to please the kernel, and causing races
with other contexts at the same time.
The only way out of this is to send tiling flags with each CS, ideally
with each relocation. But we already do that through the registers.
So let's just use what we have in the registers.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the brightness property is inquired while the backlight is disabled,
the driver returns a wrong value (zero) because it probes the value after
the backlight was turned off. This caused a black screen even after the
backlight is enabled again. It should return the internal backlight_level
instead, so that it won't be influenced by the backlight-enable state.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=41926
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/872652
Tested-by: Kamal Mostafa <kamal@canonical.com>
Cc: Alex Davis <alex14641@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Keith Packard <keithp@keithp.com>
A call to i915_add_request() has been made in function i915_gem_busy_ioctl(). i915_add_request can fail,
so in it's exit path previously allocated memory needs to be freed.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The BIOS VBT value for an eDP panel has been shown to be incorrect on
one machine, and we haven't found any machines where the DPCD value
was wrong, so we'll use the DPCD value everywhere.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Limit the link training setting command to the lanes needed for the
current mode. It seems vaguely possible that a monitor will try to
train the other lanes and fail in some way, so this seems like the
safer plan.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ben Skeggs