Previously we just set them to dpms off. This should save
additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We'll turn off outputs etc at unload time, so don't unmap the registers
before doing it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
By idling the GPU and discarding everything we can when under extreme
memory pressure, the number of OOM-killer events is dramatically
reduced. For instance, this makes it possible to run
firefox-planet-gnome.trace again on my swapless 512MiB i915.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Spatial dither is better than nothing, but ST is even better.
(from ajax's followup message:)
I noticed this with:
http://ajax.fedorapeople.org/YellowFlower.jpg
set as my desktop background in Gnome on a 1280x800 machine (in
particular, a Sony Vaio VPCB1 with 6-bit panel and a rather bright black
level). Easiest way to test this is by poking at PIPEACONF with
intel_reg_write directly:
% sudo intel_reg_write 0x70008 0xc0000040 # no dither
% sudo intel_reg_write 0x70008 0xc0000050 # spatial
% sudo intel_reg_write 0x70008 0xc0000054 # ST
I notice it especially strongly in the relatively flat dark area in the
top left. Closer than about 18" I can see a noticeable checkerboard
pattern with plain spatial dithering. ST smooths that out; I can still
tell that it's lacking color precision, but it's not offensive.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It's unused and buggy in its current form, since it can place a bo
in the reserved state without removing it from lru lists.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bring radeon up to speed with the async event synchronization for
drmWaitVblank. See c9a9c5e02a for
more information. Without this patch event never get delivered
to userspace client.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the memory is not iomem we should not try to
ioremap it. Should fix :
https://bugs.freedesktop.org/show_bug.cgi?id=27822
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/legacy: only enable load detection property on DVI-I
drm/radeon/kms: fix panel scaling adjusted mode setup
drivers/gpu/drm/drm_sysfs.c: sysfs files error handling
drivers/gpu/drm/radeon/radeon_atombios.c: range check issues
gpu: vga_switcheroo, fix lock imbalance
drivers/gpu/drm/drm_memory.c: fix check for end of loop
drivers/gpu/drm/via/via_video.c: fix off by one issue
drm/radeon/kms/agp The wrong AGP chipset can cause a NULL pointer dereference
drm/radeon/kms: r300 fix CS checker to allow zbuffer-only fastfill
DVI-D doesn't have analog. This matches the avivo behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should duplicate exactly what the ddx does for both
legacy and avivo.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the original code we used "j" as an iterator but we used "i" as an
index.
- for (j = 0; j < i; j++)
- device_remove_file(&connector->kdev,
- &connector_attrs[i]);
Smatch complained about that because "i" was potentially passed the end of
the array. Which makes sense if we should be using "j" there.
I also thought that we should remove the files for &connector_attrs_opt1
but to do that I had to add separate iterators for &connector_attrs and
&connector_attrs_opt1.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This change makes the array larger, "MAX_SUPPORTED_TV_TIMING_V1_2" is 3
and the original size "MAX_SUPPORTED_TV_TIMING" is 2.
Also there were checks that were off by one.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
"agpmem" is never NULL here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
"fx->lock" is used as the index in "dev_priv->decoder_queue[fx->lock]"
which is an array of "VIA_NR_XVMC_LOCKS" elements.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Selecting the wrong or no CONFIG_AGP_* chipset can cause a NULL pointer
dereference when combined with CONFIG_DRM_RADEON_KMS and an old system
with a R100 AGP card (should effect other cards too). The agp field
will be set to NULL if no suitable AGP chipset driver is loaded,
drm_agp_acquire already preforms a suitable NULL check so it can be used
directly.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Fix sparc regression in r300_scratch()
drm: make sure vblank interrupts are disabled at DPMS time
drm/radeon/kms/evergreen: No EnableYUV table
drm/radeon: 9800 SE has only one quadpipe
drm/radeon/kms: don't print error for legal crtcs.
drm/radeon/kms/evergreen: fix LUT setup
Previous reset code leaded to computer hard lockup (need to unplug
the power too reboot the computer) on various configuration. This
patch change the reset code to avoid hard lockup. The GPU reset
is failing most of the time but at least user can log in remotely
or properly shutdown the computer.
Two issues were leading to hard lockup :
- Writting to the scratch register lead to hard lockup most likely
because the write back mecanism is in fuzy state after GPU lockup.
- Resetting the GPU memory controller and not reinitializing it
after leaded to hard lockup. We did only reinitialize in case of
successfull reset thus unsuccessfull reset quickly leaded to hard
lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit b4fe945405 ("drm/radeon: Fix
memory allocation failures in the preKMS command stream checking.")
added a regression in that it completely tossed the get_unaligned()
done by r300_scratch() which we added in commit
958a6f8ccb ("drm: radeon: Fix unaligned
access in r300_scratch().").
Put it back.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we call drm_vblank_off() at DPMS off time (to wake any clients so
they don't hang) we need to make sure interrupts are actually disabled.
If drm_vblank_off() gets called before the vblank usage timer expires,
it'll prevent the timer from disabling interrupts since it also clears
the vblank_enabled flag for the pipe.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My PIPE_CONTROL fix (just sent via Eric's tree) was buggy; I was
testing a whole set of patches together and missed a conversion to the
new HAS_PIPE_CONTROL macro, which will cause breakage on non-Ironlake
965 class chips. Fortunately, the fix is trivial and has been tested.
Be sure to use the HAS_PIPE_CONTROL macro in i915_get_gem_seqno, or
we'll end up reading the wrong graphics memory, likely causing hangs,
crashes, or worse.
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: use PIPE_CONTROL instruction on Ironlake and Sandy Bridge
drm/i915: cleanup FBC buffers at unload time
drm/i915: fix tiling limits for i915 class hw v2
drm/i915: set DIDL using the ACPI video output device _ADR method return.
drm/i915: Fix 82854 PCI ID, and treat it like other 85X
drm/i915: Attempt to fix watermark setup on 85x (v2)
Since 965, the hardware has supported the PIPE_CONTROL command, which
provides fine grained GPU cache flushing control. On recent chipsets,
this instruction is required for reliable interrupt and sequence number
reporting in the driver.
So add support for this instruction, including workarounds, on Ironlake
and Sandy Bridge hardware.
https://bugs.freedesktop.org/show_bug.cgi?id=27108
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This keeps the memory manager from complaining when we take it down.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric mentioned on irc this patch was bad, so revert it.
This reverts commit fb8b5a39b6.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Drivers may use vblank calls now (e.g. drm_vblank_off) in their unload
paths, so don't clean up the vblank related structures until after
driver unload.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-ttm-unmappable:
drm/radeon/kms: enable use of unmappable VRAM V2
drm/ttm: remove io_ field from TTM V6
drm/vmwgfx: add support for new TTM fault callback V5
drm/nouveau/kms: add support for new TTM fault callback V5
drm/radeon/kms: add support for new fault callback V7
drm/ttm: ttm_fault callback to allow driver to handle bo placement V6
drm/ttm: split no_wait argument in 2 GPU or reserve wait
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bo.c
This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.
V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.
V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM
[airlied- squashed driver removals in here also]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback, does change anything
from driver point of view.
Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.
Patch hasn't been tested.
V2 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by TTM
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback, does change anything
from driver point of view, thought it should allow nouveau to add
support for unmappable VRAM.
Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.
Patch hasn't been tested on any hw.
V2 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.
V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On fault the driver is given the opportunity to perform any operation
it sees fit in order to place the buffer into a CPU visible area of
memory. This patch doesn't break TTM users, nouveau, vmwgfx and radeon
should keep working properly. Future patch will take advantage of this
infrastructure and remove the old path from TTM once driver are
converted.
V2 return VM_FAULT_NOPAGE if callback return -EBUSY or -ERESTARTSYS
V3 balance io_mem_reserve and io_mem_free call, fault_reserve_notify
is responsible to perform any necessary task for mapping to succeed
V4 minor cleanup, atomic_t -> bool as member is protected by reserve
mecanism from concurent access
V5 the callback is now responsible for iomapping the bo and providing
a virtual address this simplify TTM and will allow to get rid of
TTM_MEMTYPE_FLAG_NEEDS_IOREMAP
V6 use the bus addr data to decide to ioremap or this isn't needed
but we don't necesarily need to ioremap in the callback but still
allow driver to use static mapping
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Luckily the change is quite a little bit less invasive than I've
feared.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thanks to the to_intel_bo helper, this change is rather trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just embed it and adjust the pointers, No other changes (that's
for later patches).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just preparation, no functional change.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When drivers embed the core gem object into their own structures,
they'll have to do this. Temporarily this results in an ugly
kfree(gem_obj);
in every gem driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This function can be used by drivers who allocate the drm gem object
on their own. No functional change in here, just preparation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-radeon-evergreen-accel:
drm/radeon: fix cypress firmware typo.
drm/radeon/kms/evergreen: add hpd support
drm/radeon/kms/evergreen: implement irq support
drm/radeon/kms/evergreen: setup and enable the CP
drm/radeon/kms/evergreen: implement gfx init
drm/radeon/kms/evergreen: add soft reset function
drm/radeon/kms/evergreen: add gart support
drm/radeon/kms: add support for evergreen power tables
drm/radeon/kms: update atombios.h power tables for evergreen
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* drm-edid-fixes:
drm/edid: When checking duplicate standard modes, walked the probed list
drm/edid: Fix sync polarity for secondary GTF curve
drm/modes: Fix interlaced mode names
drm/edid: Add secondary GTF curve support
drm/edid: Strengthen the algorithm for standard mode codes
drm/edid: Fix the HDTV hack.
drm/edid: Extend range-based mode addition for EDID 1.4
drm/edid: Add test for monitor reduced blanking support.
drm/edid: Fix preferred mode parse for EDID 1.4
drm/edid: Remove some silly comments
drm/edid: Remove arbitrary EDID extension limit
drm/edid: Add modes for Established Timings III section
drm/edid: Reshuffle mode list construction to closer match the spec
drm/edid: Remove a redundant check
drm/edid: Remove some misleading comments
drm/edid: Fix secondary block fetch.
* drm-ttm-pool:
drm/ttm: using kmalloc/kfree requires including slab.h
drm/ttm: include linux/seq_file.h for seq_printf
drm/ttm: Add sysfs interface to control pool allocator.
drm/ttm: Use set_pages_array_wc instead of set_memory_wc.
arch/x86: Add array variants for setting memory to wc caching.
drm/nouveau: Add ttm page pool debugfs file.
drm/radeon/kms: Add ttm page pool debugfs file.
drm/ttm: Add debugfs output entry to pool allocator.
drm/ttm: add pool wc/uc page allocator V3
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
- bump userspace version]
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.
fixes fdo bug 25520.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Current code is definitely crap: Largest pitch allowed spills into
the TILING_Y bit of the fence registers ... :(
I've rewritten the limits check under the assumption that 3rd gen hw
has a 3d pitch limit of 8kb (like 2nd gen). This is supported by an
otherwise totally misleading XXX comment.
This bug mostly resulted in tiling-corrupted pixmaps because the kernel
allowed too wide buffers to be tiled. Bug brought to the light by the
xf86-video-intel 2.11 release because that unconditionally enabled
tiling for pixmaps, relying on the kernel to check things. Tiling for
the framebuffer was not affected because the ddx does some additional
checks there ensure the buffer is within hw-limits.
v2: Instead of computing the value that would be written into the
hw fence registers and then checking the limits simply check whether
the stride is above the 8kb limit. To better document the hw, add
some WARN_ONs in i915_write_fence_reg like I've done for the i830
case (using the right limits).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=27449
Tested-by: Alexander Lam <lambchop468@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
PORT_HOTPLUG_EN has allready been setup in i915_driver_irq_postinstall(),
when intel_dp_detect() runs.
Delete the DP[BCD]_HOTPLUG_INT_EN defines, they are not referenced anymore.
I found this while searching for a fix for
https://bugzilla.redhat.com/show_bug.cgi?id=528312
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
we used to set the DIDL in the output device detected order.
But some BIOSes requires it to be initialized in the ACPI device order.
e.g. the value of the first field in DIDL stands for the first
ACPI video output device in ACPI namespace.
Now we initialize the DIDL using the device id, i.e. _ADR return value,
of each ACPI video device, if it is not 0.
https://bugzilla.kernel.org/show_bug.cgi?id=15054
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This should be a small power savings. Tested on Lenovo T410 (Ironlake), LVDS
VGA and DisplayPort, up to 1920x1200R.
v2: Add Sandybridge support, fix obvious math error.
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
IS_MOBILE() catches 85x, so we'd always try to use the 9xx FIFO sizing;
since there's an explicit 85x version, this seems wrong.
v2: Handle 830m correctly too.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
Update the self-refresh watermark for display plane/cursor and enable
the memory self-refresh on Ironlake. The watermark is also updated for
the active display plane.
More than 1W idle power is saved on one Ironlake laptop after enabling
memory self-refresh.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously, after setting up the Pineview CxSR state, i9xx_update_wm would
get called and overwrite our state.
BTW: We will disable the self-refresh and never enable it any more if we
can't find the appropriate the latency on pineview plaftorm. In such case
the update_wm callback will be NULL.
The bitmask macro is also defined to access the corresponding fifo
watermark register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Otherwise it will cause that S-video output becomes black/white when
switching to other TV format.
http://bugs.freedesktop.org/show_bug.cgi?id=23916
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Arnold <arnold.erbsloeh@web.de>
Tested-by: Bazin <bazin.cz@gmail.com>
Tested-by: Nigel <nigel_tuck@eircom.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
SDVO on Ibexpeak PCH with Ironlake is multiplexed with
HDMIB port, and only has SDVOB port.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The existing code handling the DPMS ON event is much more careful to
ensure that these registers are enabled according to strict sequencing
requirements. Enabling these early in mode_set simply defeats that.
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
->dev_private at that point is NULL and is initialied only a few lines
later.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This reverts commit 6070a4a928.
The quirk for this SDVO device on IBM specific board is just a hack
in old code which showed the broken multifunction SDVO support in
the driver. Multifunction SDVO patch provided the right fix for it.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
With new intel_encoder/intel_connector structure change, each supported
connector type on SDVO device will be created as a new 'intel_connector',
and all attached to one 'intel_encoder' for its SDVO port.
The SDVO encoder will handle SDVO protocol stuff, and each connector does
its own part of work now, like detection is only to check if current active
output is itself, etc.
Update since last submit:
- Fixed SDVO TV property creation failure by incorrect set target output call
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
As all display drivers have been converted, remove the left reference
for connector object in old structure.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Probably only matters for format-converting dongles, but might as well
get it right all the time.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
DP on Cougarpoint has new training pattern definitions, and
new transcoder DP control register is used to determine the mapping
for transcoder and DP digital output. And eDP for Sandybridge has
new voltage and pre-emphasis level definitions.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To make CRT force detect reliable on Cougarpoint, we need to
disable DAC before force detect, and restore back when trigger
is completed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cougarpoint is the new PCH for Sandybridge CPU. This one resolves the
chipset change for display pipeline compared to previous Ibexpeak PCH.
Sandybridge/Cougarpoint has different FDI training parameters, so this also
makes seperate FDI training functions for IBX and CPT. Other change includes
new transcoder DPLL select function to set which DPLL for transcoder to pick
up.
And with another new transcoder C introduced in Cougarpoint, each connector
has new transcoder select bits. This one adds that change to light up VGA.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
PCH is the new name for south bridge from Ironlake/Sandybridge,
which contains most of the display outputs except eDP. This one
adds a probe function to detect current PCH type, and method to
detect Cougarpoint PCH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Integrated TV is deprecated in new chips from Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
OpRegion event on 965G requires legacy BLC event enabled in pipe stat. As LVDS
could be on either pipe now, we should enable BLC event on both pipe. If fail to
do so, we couldn't handle the brightness request triggered from graphics
opregion.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This was brought over from UMS, and used for a while until we decided
that drm_helper_resume_force_mode was easier and more reliable, since
it didn't require duplicating all the code deleted here. We just
forgot to delete all that junk for a while.
On X startup we were getting a flicker where there shouldn't have been one.
the X DDX calls the kernel to set the properties to the same values (yes
it could be smarter), however the kernel was doing a pointless modeset then,
making my nice smooth boot ugly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This trys to shut up complains about invalid LVDS EDID during
mode probe, but uses fixed panel mode directly for panels with
broken EDID.
https://bugs.freedesktop.org/show_bug.cgi?id=23099https://bugs.freedesktop.org/show_bug.cgi?id=26395
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
shr/shl ops need the full dst rather than the pre-masked
version. Fixes fdo bug 27478 and kernel bug 15738.
v2: remove some unsed vars, add comments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This one replaces original param for intel_ddc_get_modes() with
DRM connector and i2c bus adapter instead. With explicit params,
we won't require that a single driver structure must hold connector
and DDC bus reference, which ease the conversion to splitted encoder/
connector model.
It also clears up for some cases that we would steal other DDC bus
for mode probe, like VGA analog DDC probe for DVI-I. Also it fixed
a bug in old DVI-I probe handling, that failed to restore origin
analog GPIO port.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In load detection, connector's encoder assignment must be kept
consistent for proper mode setting, and this makes connector as
explicit parameter for load detect function to not require single
data structure to hold both encoder and connector reference, ease
the transition for splitted encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For introducing splitted encoder/connector structure, this helper will return
connector's attached encoder when needed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds new structure of intel_connector to present drm's
connector object, which is used to convert from origin single
output into encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
What we really want is encoder info instead of connector, so change
some more list walk in pipeline setup functions from connector_list
to encoder_list.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of walking through drm connector_list uses encoder_list
for calling hotplug functions which is consistent with intel display
hotplug reporting.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The TV detection logic is not reliable on the Cantiga platform.
Sometimes the TV will be misdetected as the following two cases:
- TV is misdetected on some laptops. e.g. There is no TV connector
port or no TV is attached. But the TV is shown as connected.
- TV connector type is misdetected. e.g. the component TV is
attached, but the TV is shown as S-video type.
According to the hardware requirement, the TV sense state bits of TV DAC
register should be cleared to zero on Cantiga platfrom.
https://bugzilla.kernel.org/show_bug.cgi?id=14792
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Santi <santi@agolina.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (29 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
* 'nouveau/for-airlied' of ../drm-nouveau-next: (21 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
The command processor (CP) fetches command buffers and
feeds the GPU. This patch requires the evergreen
family me and pfp ucode files.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initializes the gfx engine so accel can
eventually be used.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes garbled 3D on an nv46 card.
Reported-by: Francesco Marella <francesco.marella@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allows *some* DP cards to keep working in some corner cases that most
people shouldn't hit. I hit it all the time with development, so this
can stay for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This value interacts with some registers we don't currently know how to
program properly ourselves. The default of 5 that we were using matches
what the VBIOS on early DP cards do, but later ones use 6, which would
cause nouveau to program an incorrect mode on these chips.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Gart setup is more or less like r7xx. Copy
rv770d.h to evergreend.h and fix up changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All indications seem to be that the version 0x30 table should be handled
the same way as 0x40 (as used on G80), at least for the parts that we
currently try use.
This commit cleans up the parsing to make it clearer about what we're
actually trying to achieve, and unifies the 0x30/0x40 parsing.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As opposed to repeatedly reading the amount back from the GPU every
time we need to know the VRAM size.
We should now fail to load gracefully on detecting no VRAM, rather than
something potentially messy happening.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previously we were filling it the same as "placements", but in some
cases there're valid alternatives that we were ignoring completely.
Keeping a back-up memory type helps on several low-mem situations.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes the !vbo_fifo path in the 3D driver on certain chipsets. Still not
really any good idea of what exactly the magic achieves, but it makes
things work.
While we're at it, in the PCIEGART path, flush on unbinding also.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alex Deucher
