This patch add documentation for binding of USB Type C cable detection
mechanism is using EXTCON subsystem. The device can detect the presence
of display out but it may also detect other external accessories when
external accessories is attached or detached.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Driver can now work with both ID and VBUS pins or either one of
them.
There can be the following 3 cases
1) Both ID and VBUS GPIOs are available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB state is same as VBUS.
2) Only ID GPIO is available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB active
3) Only VBUS GPIO is available:
VBUS = LOW -> USB_HOST inactive, USB inactive
VBUS = HIGH -> USB_HOST inactive, USB active
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some Qualcomm PMICs have a misc device that performs USB id pin
detection via an interrupt. When the interrupt triggers, we
should read the interrupt line to see if it has gone high or low.
If the interrupt is low then the ID pin is grounded, and if the
interrupt is high then the ID pin is being held high.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
[cw00.choi: Edited the driver description and added the author information]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update the binding documentation to mention the defines added for the
possible values of wlf,gpsw.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Maxim Integrated MAX3355E chip integrates a charge pump and comparators to
enable a system with an integrated USB OTG dual-role transceiver to
function as an USB OTG dual-role device. In addition to sensing/controlling
Vbus, the chip also passes thru the ID signal from the USB OTG connector.
On some Renesas boards, this signal is just fed into the SoC thru a GPIO
pin -- there's no real OTG controller, only host and gadget USB controllers
sharing the same USB bus; however, we'd like to allow host or gadget
drivers to be loaded depending on the cable type, hence the need for the
MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs
(however, we aren't currently interested in them), the OFFVBUS# signal is
controlled by the host controllers, there's also the SHDN# signal wired to
a GPIO, it should be driven high for the normal operation.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
[cw00.choi: Add the GPIOLIB dependency]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add an example for all elements of the Arizona extcon device tree
binding.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update the device tree binding documentation to include documentation for
the wlf,micd-configs property that is used to specify the configurations
for headset polarity detection (CTIA / OTMP).
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add time units of -ms (milliseconds) to wlf,micd-timeout.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update the name for the second jack detection pin binding to be a little
less confusing.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add additional bindings for both inverting the polarity of the jack
detection pins and allowing the use of a second jack detection pin. Note
that the second jack detection pin is hard wired in the chip so can only
be enabled through the binding, rather than a pin being specified.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add additional bindings to allow configuration of the system specific
microphone detection settings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Subsystem specific bindings for the Arizona devices are being factored
out of the MFD binding document into separate documents for each
subsystem. This patch adds a binding document that covers the existing
extcon specific bindings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some palmas based chip variants do not have OTG based ID logic.
For these variants we rely on GPIO based USB ID detection.
These chips do have VBUS comparator for VBUS detection so we
continue to use the old way of detecting VBUS.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This driver observes the USB ID pin connected over a GPIO and
updates the USB cable extcon states accordingly.
The existing GPIO extcon driver is not suitable for this purpose
as it needs to be taught to understand USB cable states and it
can't handle more than one cable per instance.
For the USB case we need to handle 2 cable states.
1) USB (attach/detach)
2) USB-HOST (attach/detach)
This driver can be easily updated in the future to handle VBUS
events in case it happens to be available on GPIO for any platform.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch add documentation for binding of Richtek RT8973A (Micro USB Switch)
device which is using EXTCON subsystem. The RT8973A device can detect various
external accessories when external accessories is attached or detached.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch add documentation for binding of SM5502 MUIC (Micro-USB Interface
Controller) device which is using EXTCON subsystem. The SM5502 MUIC device
can detect various external accessories when external accessories is attached
or detached.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The Palmas device contains only a USB VBUS-ID detector, so added a
compatible type *ti,palmas-usb-vid*. Didn't remove the existing compatible
types for backward compatibility.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Based on system design, platform needs to detect the VBUS or ID or
both. Provide option to select this through platform data to
disable part of cable detection through palmas-usb.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Extcon for palma driver does not need vbus supply and hence
removing this from devicetree document/bindings.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The driver name is extcon/extcon-palmas.c and hence renaming the
device tree binding document to extcon-palmas.txt.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This is the driver for the USB comparator built into the palmas chip. It
handles the various USB OTG events that can be generated by cable
insertion/removal.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
[kishon@ti.com: adapted palmas usb driver to use the extcon framework]
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benson Leung