Use shiny new link APIs to manage the links. Also remove old link
configuration logic from driver.
We need to keep link and cmd dma to off during active suspend
to allow system to enter low power state and turn it on if
the link and cmd dma was on before active suspend in active
resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During skl_nhlt_init(), acpi obj pointer is allocated and never
freed and remap address is not unmapped.
To fix this we should release the ACPI obj and also unmap the
nhlt address during cleanup of driver.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCI bus takes pci_dev_get() and pci_dev_put() is also there.
So no need for drivers to invoke these. In SKL driver we were
calling pci_dev_put() only which is not right, so remove this
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skylake driver uses i915 component APIs to talk to display.
On remove we should free up by invoking snd_hdac_i915_exit() but
that should be last thing in remove routine, so move it to last
in skl_free()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In Skylake destructor we unmap the hardware address and then free
links and streams. The stream free accesses hardware to write to
registers and predictably causes oops.
So change the order and unmap last in destructor.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On driver removal we should ask the core to remove the device
objects as well, so invoke snd_hdac_ext_bus_device_remove() in
remove.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton is an Intel SoC which sports a DSP and system is quite
like Skylake. So add this ID in Skylake driver
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SKL also supports HDMI output so in probe we need to enable
the HDMI using common i915 APIs to ensure it gets probed on the
bus
After S3 during the controller resequencing the codec domain need
to be kept ON for successful reconfiguration of Codec. Once
configured it will be turned OFF in codec driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
NHLT table [1] header has fields like oem_id, oem_table_id and
oem_revision. Use that to load a unique topology binary specific
to that platform
NHLT Table is documented at:
[1]: https://01.org/blogs/2016/intel-smart-sound-technology-audio-dsp
Signed-off-by: Yang A Fang <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While going to shutdown, we need to bring HW to clean state. This
is done by cleaning up stream descriptor registers. This cleanup
is already done by decoupling of stream and stopping the chip, so
invoke these from shutdown handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver used autosuspend delay to delay going to D3. But per
HW recommendation we should go to D3 soon, so remove the delay
from driver
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In active suspend, any HDA interrupt should wake the system. When device
enters active suspend, we need to enable HDA controller interrupt as wake
source. Similarly disable HDA controller interrupt as wake source when
exiting active suspend.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When device enters active suspend, we should turn off the links
as they are not in use. Similarly we need to bring back links
when we exit active suspend.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MISCBDCGE is a new register for Misc Backbone clock gate control
which is useful to control while resetting the link and ensuring
controller is in required state so add API to control it
HW recommends that we reset with CGCTL.MISCBDCGE disabled, so add
that while doing init chip and reset sequence.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This provide the fix for firmware memory by freeing the pointer in driver
remove where it is safe to do so
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the NAU88L25 + MAX98357A machine driver entry into
the machine table
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the usecases can be marked as 'ignore_suspend' by
machine. For these on suspend we should keep audio controller
ON by saving the state and not suspending the device
For this we need to maintain a counter for these streams and be
active on suspend when such a stream is opened.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we call _skl_resume which also initializes the chip we no
need to call these explicitly, so remove the duplication
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For HDA codecs WAKEENABLE bit is to programmed if codec event
change has to wake the system when suspended.
In skylake I2S systems which are currently supported we have
only HDMI codec, which doesn't use this capability to detect a
HDMI connect/ disconnect event. HDMI HDA codec uses display
interface to detect connect/disconnect event.
This patch removes the WAKEBIT enabling during device D0/D3 as
this seems to cause spurious wakes on the system
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds skl_nau8825_ssn4567_i2s machine driver into
machine table
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware name is hard coded which doesnt allow to load
different platforms for various platforms so get this name from
available machine table and pass it to dsp context for loading
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have common match code in place, update the SKL
driver to use the common match routines for driver entry creation
for UEFI BIOS systems
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver runtime behaviour is fine but in suspend, we missed
setting the DSP to suspend and also missed resuming DSP on
resume.
Fix this by having common SKL suspend and resume routines which
power up/down links, suspend/resume DSP and other common
routines, and call these routines from both runtime as well as
system PM handlers
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have both I2S and hda codec support in the driver. codec_mask
check is relevant only for hda codec and some boards may have
only I2S Codec, so removed probe error in case no hda codec is
found and update the log to info as it may not be error.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This ensures that the link is not requesting any clock and the
PLL can turn off. The link is powered when controller is brought
out of reset.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Load and Initialize Non HDA Link Table in Skylake driver
to get platform configuration.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Decoupled mode is where audio link is broken to frontend HDA and backend
(hda/i2s/dmic/hdmi) links. This patch adds support for decoupled mode and
then adds dais, dai ops for be/fe cpu dais and interrupt handler change to
support decoupled mode
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch follows up by adding the HDA controller operations. This
code is mostly derived from Intel HDA PCI driver without legacy bits
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul