PMP registers used to be accessed with dedicated accessors ->pmp_read
and ->pmp_write. During reset, those callbacks are called with the
port frozen so they should be able to run without depending on
interrupt delivery. To achieve this, they were implemented polling.
However, as resetting the host port makes the PMP to isolate fan-out
ports until SError.X is cleared, resetting fan-out ports while port is
frozen doesn't buy much additional safety.
This patch updates libata PMP support such that PMP registers are
accessed using regular ata_exec_internal() mechanism and kills
->pmp_read/write() callbacks. The following changes are made.
* PMP access helpers - sata_pmp_read_init_tf(), sata_pmp_read_val(),
sata_pmp_write_init_tf() are folded into sata_pmp_read/write() which
are now standalone PMP register access functions.
* sata_pmp_read/write() returns err_mask instead of rc. This is
consistent with other functions which issue internal commands and
allows more detailed error reporting.
* ahci interrupt handler is modified to ignore BAD_PMP and
spurious/illegal completion IRQs while reset is in progress. These
conditions are expected during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Asynchronous notification on ICH9 didn't work because it didn't write
AN FIS into the RX area - it only updates SNotification. Also,
snooping SDB_FIS RX area is racy against further SDB FIS receptions.
Let sata_async_notification() determine using SNTF if it's available
and snoop RX area iff SNTF isn't available
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that we have pp->intr_mask, move PORT_IRQ_BAD_PMP enabling to
ahci_pmp_attach/detach() where it belongs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci had problems with NCQ over PMP and NCQ used to be disabled while
PMP was attached. After fixing the problem, the temporary NCQ
disabling code wasn't removed completely. Kill the remaining piece.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Of course some controllers lie about PMP support. Black list them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Private pi.flags area is full and we need more private flags. Move
host private flags over to pi.private_data. During initialization,
these flags are copied to hpriv->flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement AHCI PMP support. ahci only supports command based
switching. Also, for some reason, NCQ over PMP doesn't work now.
Other than that, everything works.
Tested on ICH9R, JMB360/363 + SIMG3726, 4726 and 5744.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Forrest Zhao <forrest.zhao@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AHCI spec says host-reset bit may only be set when the ahci-enable bit
is also set.
Noticed by Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AN serves multiple purposes. For ATAPI, it's used for media change
notification. For PMP, for downstream PHY status change notification.
Implement sata_async_notification() which demultiplexes AN.
To avoid unnecessary port events, ATAPI AN is not enabled if PMP is
attached but SNTF is not available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently. This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.
If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link. If ATA_DEFER_PORT, until a qc completes
on any link. The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.
ops->qc_defer() replaces fixed ata_scmd_need_defer(). For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented. ahci and
sata_sil24 are converted to use ata_std_qc_defer().
ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.
IMHO, this shouldn't cause any noticeable performance issues as
* for most cases deferring occurs rarely (except for NCQ-aware
cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
completes which usually is a very long time cpu-wise.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update AN support in preparation of PMP support.
* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement port_map handling such that
1. Non-zero PORTS_IMPL value is always examined and used if consistent
with cap.n_ports.
2. When PI and cat.n_ports are inconsistent, honor cap.n_ports and
force port_map to be ((1 << cap.n_ports) - 1).
3. There were two separate places dealing with port_map. Unify them
to one.
As all newer ahci chips seem to get PI correct and older ones usually
have zero PI. Controllers with holes in PI are very unlikely to screw
up PI, so #2 makes more sense than following inconsistent PI.
Without this change, not setting ATA_FLAG_HONOR_PI when it's needed
results in weird detection failure. This changed logic should be able
to handle all known cases correctly automatically.
Verified on ICH6 (reports 0 PI), ICH8 (with holes in port_map), ICH9,
JMB360 and JMB363.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use a stored value for which interrupts to enable. Changing this allows
us to selectively turn off certain interrupts later and have them
stay off.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When we get an SDB FIS with the 'N' bit set, we should send
an event to user space to indicate that there has been a
media change. This will be done via the scsi device.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATI/AMD SB800 shares some device IDs with SB700,
and SB800 adds two more device IDs:0x4394,0x4395.
Signed-off-by: henry su <henry.su.ati@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
the onchip SATA type set in the system BIOS:
Device Device ID
SATA in IDE mode 0x4390
SATA in AHCI mode 0x4391
SATA in non-raid5 driver 0x4392
SATA in raid5 driver 0x4393
Although the device ID is different, they use the same AHCI driver
.The attached file is the patch for adding these device
IDs for ATI SB700.
Signed-off-by: henry.su.ati@gmail.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ahci_scr_read/write() handle SCR_NOTIFICATION if the controller
supports it. Also, print "sntf" in the cap line if supported.
While at it, convert eight space into a tab in ahci_print_info().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci_save_initial_config() is responsible for reading, screening the
host CAP register and storing the modified result into hpriv->cap for
the rest of the driver. Move ATA_FLAG_NO_NCQ handling into
ahci_save_initial_config(). It's more consistent this way and the
rest of the driver can always refer to hpriv->cap to determine
configured capability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ->scr_read/write callbacks to return error code to better
indicate failure. This will help handling of SCR_NOTIFICATION.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Requiring LLDs to format multiple error description messages properly
doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation. __ata_ehi_push_desc() is the raw
version without the automatic separator.
While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ahci_do_softreset() which takes @pmp as its last
argument. This will be used to implement ahci_pmp_softreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ahci_exec_polled_cmd() from ahci_softreset(). This will
be used to implement ahci_pmp_read/write(). ahci_exec_polled_cmd()
performs reset_engine before returning if the command fails (times
out). This is to improve robustness.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out stop_engine - CLO - start_engine sequence from
ahci_softreset() and ahci_clo() into ahci_reset_engine() and use it in
ahci_softreset() and ahci_post_internal_cmd(). The function will also
be used to prepare for and clean up after PMP register access
commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use deadline instead of fixed timeout for 1st FIS for SRST to improve
robustness of SRST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @is_cmd to ata_tf_to_fis(). This controls bit 7 of the second
byte which tells the device whether this H2D FIS is for a command or
not. This cleans up ahci a bit and will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit df69c9c543 moved only prototype of
out of CONFIG_PM. Move function out as well. Box seems to boot fine.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the SATA portion of Marvell's AHCI-compatible chips.
The PATA port capability, also available via AHCI, is disabled until
support is completed.
NCQ and PCI MSI are disabled by default. Marvell says "we use NCQ" in
their drivers but "we do not use PCI MSI." Theoretically that implies
we need to fix ahci.c to work with Marvell NCQ, but one wonders why
Marvell NCQ is any different from other AHCI chips.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Use ATA_UDMA*
* Remove FIXME notations that once served to remind us to verify
that these were indeed the correct UDMA masks. They are.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci: enable sg segment clustering
The specification states that ahci supports segments up to 4MiB in size,
so enable clustering.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PORTS_IMPL register is zero, ahci initialize it to full mask
corresponding to nr_ports in the CAP register. hpriv->cap, which is
initialized at the end of the function, is incorrectly used as value
of CAP causing ahci to always override PORTS_IMPL to 0x1 if it's zero.
Fix it.
This fixes a bug where early ich6 ahci can only access the first port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whether a controller needs IDE or SATA ACPI hierarchy is determined by
the programming interface of the controller not by whether the
controller is SATA or PATA, or it supports slave device or not. This
patch adds ATA_FLAG_ACPI_SATA port flags which tells libata-acpi that
the port needs SATA ACPI nodes, and sets the flag for ahci and
sata_sil24.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the device ID to AHCI pci table for ATI SB700 SATA controller, the
subsequent chipset of SB600.
Signed-off-by: henry su<henry.su@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For PATA, 0xff status indicates empty port. For SATA, it depends on
how the controller emulates status register. On some controllers,
0xff is used to represent broken link or certain stage during reset.
libata currently deals SATA the same. This hasn't caused any problem
because problematic situations usually only occur after hotplug or
other link disruption events and libata blindly waited for the device
to spin up and settle after hotplug giving the link and device
whatever time to go through those stages.
libata is going to replace unconditional spinup wait with generic
timed sequence of resets, so not only getting 0xff handling right for
SATA is, well, the right thing to do, it's much more important now.
This patch makes the following changes.
* Make ata_bus_softreset() return -ENODEV if any of its wait fails
due to 0xff status.
* Fail soft/hardreset if status wait returns -ENODEV indicating 0xff
status while SStatus says the link is online. e.g. Reset fails if
status is 0xff after reset when SStatus reports the linke is online.
If SCR registers are not available, everything is the same as
before.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.
* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.
* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.
There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.
2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.
3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.
If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.
* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.
* Spin up waiting is to be removed and not converted to honor
deadline.
* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo