- bail out on unsupported VFL_TYPE
- em28xx_set_mode() needs to be called for VBI and radio mode, too
- em28xx_wake_i2c() needs to be called for VBI and radio mode, too
- em28xx_resolution_set() also needs to be called for VBI
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that em28xx can be compiled without V4L support, we should
call em28xx_setup_xc3028() on both em28xx-v4l and em28xx-dvb
modules.
Reported-by: Chris Lee <updatelee@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The URB calculus code may eventually be moved to some other
place, like at pcm open, if it ends by needing more setups, like
working with different bit rates, or different audio latency.
So, move it into a separate routine. That also makes the code
more readable.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pulseaudio has the bad habit of stopping a streaming audio if
a device, opened in non-block mode, waits.
It is impossible to avoid em28xx to wait, as it will send commands
via I2C, and other I2C operations may be happening (firmware
transfers, Remote Controller polling, etc). Yet, as each em28xx
subdriver locks em28xx-dev to protect the access to the hardware,
it is possible to minimize the audio glitches by returning -EAGAIN
to pulseaudio, if the lock is already taken by another subdriver.
Reported-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the period size is wrong, userspace will assume a wrong delay
any may negociate an inadequate value.
The em28xx devices use 8 for URB interval, in microframes,
and the driver programs it to have 64 packets.
That means that the IRQ sampling period is 125 * 8 * 64,
with is equal to 64 ms.
So, that's the minimal latency with the current settings. It is
possible to program a lower latency, by using less than 64 packets,
but that increases the amount of bandwitdh used, and the number of
IRQ events per second.
In any case, in order to support it, the driver logic should be
changed to fill those parameters in realtime.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current code hardcodes the number of audio URBs, the number
of packets per URB and the maximum URB size.
This is not a good idea, as it:
- wastes more bandwidth than necessary, by using a very
large number of packets;
- those constants are bound to an specific scenario, with
a bandwidth of 48 kHz;
- don't take the maximum endpoint size into account;
- with urb->interval = 1 on xHCI, those constraints cause a "funny"
setup: URBs with 64 packets inside, with only 24 bytes total. E. g.
a complete waste of space.
Change the code to do dynamic URB audio calculus and allocation.
For now, use the same constraints as used before this patch, to
avoid regressions.
A good scenario (tested) seems to use those defines, instead:
#define EM28XX_MAX_AUDIO_BUFS 8
#define EM28XX_MIN_AUDIO_PACKETS 2
But let's not do such change here, letting the optimization to
happen on latter patches, after more tests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just filling urb->interval with 1 is wrong, and causes a different
behaviour with xHCI.
With EHCI, the URB size is typically 192 bytes. However, as
xHCI specifies intervals in microframes, the URB size becomes
too short (24 bytes).
With this patch, the interval will be properly initialized, and
the device will behave the same if connected into a xHCI or an
EHCI device port.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If i2c_debug is enabled, we splicitly want to know when a
device fails with timeout.
If i2c_debug==2, this is already provided, for each I2C transfer
that fails.
However, most of the time, we don't need to go that far. We just
want to know that I2C transfers fail.
So, add such errors for normal (ret == 0x10) I2C aborted timeouts.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C output messages is too polluted. Clean it a little
bit, by:
- use the proper core support for memory dumps;
- hide most stuff under the i2c_debug umbrella;
- add the missing KERN_CONT where needed;
- use 2 levels or verbosity. Only the second one
will show the I2C transfer data.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Follow the error codes for I2C as described at Documentation/i2c/fault-codes.
In the case of the I2C status register (0x05), this is mapped into:
- ENXIO - when reg 05 returns 0x10
- ETIMEDOUT - when the device is not temporarily not responding
(e. g. reg 05 returning something not 0x10 or 0x00)
- EIO - for generic I/O errors that don't fit into the above.
In the specific case of 0-byte reads, used only during I2C device
probing, it keeps returning -ENODEV.
TODO: return EBUSY when reg 05 returns 0x20 on em2874 and upper.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the lack of a better spec, let's assume the timeout
values compatible with SMBus spec:
http://smbus.org/specs/smbus110.pdf
at chapter 8 - Electrical Characteristics of SMBus devices
Ok, SMBus is a subset of I2C, and not all devices will be
following it, but the timeout value before this patch was not
even following the spec.
So, while we don't have a better guess for it, use 35 + 1
ms as the timeout.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This macro is used by all em28xx devices, and not just em2800.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C wait completion/timeout logic currently assumes that
msleep(5) will wait exaclty 5 ms. This is not true at all,
as it depends on CONFIG_HZ.
Convert it to use jiffies, in order to not wait for more time
than needed.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of assuming that msleep() is precise, use a jiffies
based code to wait for AC97 to be available.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating/deallocating URBs and transfer buffers
every time stream is started/stopped, just do it once.
That reduces the memory allocation pressure and makes the
code that start/stop streaming a way simpler.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating transfer buffers with kmalloc() use
usb_alloc_coherent().
This patch should make it work also with ARM CPUs.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The audio configuration in chip config register 0x00 and eeprom are always
consistent. But currently the audio configuration #defines for the chip config
register say 0x20 means 3 sample rates and 0x30 5 sample rates, while the eeprom
info output says 0x20 means 1 sample rate and 0x30 3 sample rates.
I've checked the datasheet excerpts I have and it seems that the meaning of
these bits is different for em2820/40 (1 and 3 sample rates) and em2860+
(3 and 5 smaple rates).
I have also checked my Hauppauge WinTV USB 2 (em2840) and the chip/eeprom
audio config 0x20 matches the sample rates reproted by the USB device
descriptor (32k only).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot:
All error/warnings:
>> ERROR: "em28xx_release_resources" [drivers/media/usb/em28xx/em28xx-v4l.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Emitting an OOM message isn't necessary after input_allocate_device
as there's a generic OOM and a dump_stack already done.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A few devices (em2860) use a separate interface for audio only
Audio Vendor Class USB. That interface should not be used by
Remote Controller, Analog TV or Digital TV.
Prevents initializing all non-audio extensions for the audio
only interface.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the same module version on all em28xx sub-modules, and use
the same naming convention to describe the driver.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Better to split chipset detection from the audio setup. So, move the
detection code to em28xx_init_dev().
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a message with consistent prints before and after each
extension initialization, and provide a better text for module
load.
While here, add a missing sanity check for extension finish
code at em28xx-v4l extension.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that all analog-specific code are at em28xx-video, convert
it into an em28xx extension and load it as a separate module.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the error handling logic, making it to unregister i2c bus 0, in
case of a failure to register the second bus.
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several init code inside em28xx-cards that are actually
part of analog initialization. Move the code to em28x-video, in
order to remove part of the mess.
In thesis, no functional changes so far.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When em28xx extensions are loaded/removed, there are two locks:
a single static em28xx_devlist_mutex that registers each extension
and the struct em28xx dev->lock.
When extensions are registered, em28xx_devlist_mutex is taken first,
and then dev->lock.
Be sure that, when extensions are being removed, the same order
will be used.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to make easier for the next patches, do some
cosmetic changes.
No functional changes.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that we want to split the video handling to a separate
module, move all video-specific functions to em28xx-video.
No functional changes.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For GPI-connected buttons without (hardware) debouncing, the polling interval
needs to be reduced to detect button presses properly.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New chip version, which is very similar than EM28174.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The SpeedLink Vicious And Devine Laplace webcam is using an EM2765 bridge and
an OV2640 sensor. It has a built-in microphone (USB standard device class)
and provides 3 buttons (snapshot, illumination, mute) and 2 LEDs (capturing/mute
and illumination/flash). It is also equipped with an eeprom.
The device is available in two colors: white (1ae7:9003) and black (1ae7:9004).
For further details see http://linuxtv.org/wiki/index.php/VAD_Laplace.
Please note the following limitations that need to be addressed later:
- resolution limited to 640x480 (sensor supports 1600x1200)
- picture quality needs to be improved
- AV-mute button doesn't work yet
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The SpeedLink VAD Laplace webcam is equipped with an illumination button and
an illumination LED. When the button is pressed, the driver must toggle the
LED state via the corresponding GPO port.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Introduce a LED role and store all LEDs in an array.
Also provide a helper function to retrieve a specific LED.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So far, the driver only supports a snapshot button which is assigned to
register 0x0c bit 5. This special port has a built-in debouncing mechanism.
For buttons connected to ordinary GPI ports, this patch implements a software
debouncing mechanism.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current code supports only a single snapshot button assigned to
register 0x0c bit 5. But devices may be equipped with multiple buttons
with different functionalities and they can also be assigned to the
various GPI-ports.
Extend the em28xx-input code to handle multiple buttons assigned to different
GPI-ports / register addresses and bits.
Also make easier to extend the code with further button types.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some devices are equipped with a capturing status LED that needs to be
switched on/off explicitly via a GPO port.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vb2_fop_release might take the video queue mutex lock.
In order to avoid nesting mutexes the private mutex is taken after the
fop_release has finished.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the UB435-Q V2. You might need to
use the device once with the Windows driver provided by KWorld
in order to permanently reprogram the device descriptors. Thanks
to Jarod Wilson for the initial attempt at adding support for this
device.
[m.chehab@samsung.com: Fixed Whitespace mangling, Coding Style and
improved the error handling at DVB attach]
Signed-off-by: Jean-Francois Thibert <jfthibert@google.com>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The em28xx driver only calls subdevices' .s_power() method to power them
down, relying on the hardware to wake up automatically, which is usually
the case with tuners. This was acceptable with the old .standby() method,
but is wrong with .s_power(). Fixing the driver would be difficult due to
a broad supported hardware base. Instead this patch makes use of the
unbalanced_power soc-camera subdevice flag to tell the ov2640 driver to
balance calls to v4l2_clk_enable() and v4l2_clk_disable() internally.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Camera sensors usually require a master clock for data sampling. This patch
registers such a clock source for em28xx cameras. This fixes the currently
broken em28xx ov2640 camera support and can also be used by other camera
sensors.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Increase the streaming_users count only if streaming start succeeds.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix CodingStyle on the GPIO init tables.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That version of DRX-K chip supports only 2.
drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
drxk: Warning -22 on qam_demodulator_command
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tda18271c2dd => tda18271
tda18271 is more complete than tda18271c2dd.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Downloading new firmware for DRX-K demodulator is not obligatory but
usually it offers important bug fixes compared to default firmware
burned into chip rom. DRX-K demod driver will continue even without
the firmware, but in that case it will print warning to system log
to tip user he should install firmware.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set the config structure pointer to the eeprom data pointer (data,
here eedata dereferenced) not the pointer to the pointer to
the eeprom data (eedata itself).
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org # for v3.10
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Set fmt.pix.priv to zero in vidioc_try_fmt_vid_cap.
Catched by v4l2-compliance.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
[hans.verkuil@cisco.com: dropping unnecessary change to g_fmt_vid_cap]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The GPIO register caching is the result of wrong assumptions and incomplete
knowledge about the GPIO registers and their functionality.
Today, we know that it is not needed.
It is also limited to a single register and therefore incomplete (newer chips
are using multiple registers).
Instead of extending the caching, get rid of it, because it has no real
benefits and just bloats/complicates the code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- add definition for GPIO register 0x09 (reading/input)
- extend the information the chip variants that support GPIO registers 0x08/0x09
- rename EM28XX_R08_GPIO to EM2820_R08_GPIO_CTRL
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em25xx/em276x/7x/8x provides 4 GPIO register sets,
each of them consisting of separate read and a write registers.
The same registers are also used by the em2874/174/84.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the V4L2_IDENT_* usage with tveeprom-specific defines. This header
is deprecated, so those defines shouldn't be used anymore.
The em28xx driver is the only one that uses the tveeprom audio_processor
field, so that has been updated to use the new tveeprom AUDPROC define.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
In addition to commit 72cc9ba3 "em28xx: ignore isoc DVB USB endpoints with
wMaxPacketSize = 0 bytes for all alt settings" we should not save the endpoint
number of the isoc DVB endpoint before it has been validated.
While the current code works fine, dev->dvb_ep_isoc != 0 could be interpreted
as indicator that the device provides DVB support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 61ff5d69 "em28xx: improve em2710/em2820 distinction" missed the
le16_to_cpu conversion of the USB vendor ID.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit cd634f1 ("[media] v4l2: put VIDIOC_DBG_G_CHIP_NAME under
ADV_DEBUG") missed the initializer of radio_ioctl_ops:
drivers/media/usb/em28xx/em28xx-video.c:1830:2: error: unknown field 'vidioc_g_chip_info' specified in initializer
drivers/media/usb/em28xx/em28xx-video.c:1830:26: error: 'vidioc_g_chip_info' undeclared here (not in a function)
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chip id 18 is used by the em2710 and em2820.
The current code assumes that if the device is a camera, the chip is an em2710
and an em2820 otherwise.
But it turned out that the em2820 is also used in camera devices.
"Silvercrest 1.3 MPix" webcams for example are available with both chips.
Fortunately both variants are using different generic USD IDs which give us a
hint about the used chip.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The snapshot button support is currently broken, because module em28xx-rc is
loaded only if the device has remote control support.
Fix it by also loading this module if the device has a snapshot button.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb->adapter.priv should also be set to the i2c bus since that's what
em28xx_tuner_callback expects.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl will be extended to return more information than just the name.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only enable this ioctl if the VIDEO_ADV_DEBUG config option is set. This
prevents abuse from both userspace and kernelspace (some bridge drivers
abuse DBG_G_CHIP_IDENT, lets prevent that from happening again with this
ioctl).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx: fix typo in scale_to_size().
The second hscale should be vscale. This bug caused xawtv to fail because it
cannot find a workable image size.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-cards.c is very large and the sensor/camera related code is growing,
so move this code to a separate source code file em28xx-camera.c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the board hints and the sensor initialization/configuration have been
separated, em28xx_detect_sensor() is the better name for this function.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sensor detection and initialization/configuration are currently mixed together.
This works as long as all devices with a particular sensor are working with the
same board configuration. In the long run, this will be not sufficient, so
separate these both steps to make the code more flexible and future proof.
This also makes the code more consistent, because the initialization of the
MT9V011 sensor subdevice is already separated.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current board hint code is mixed together with the sensor detection and
initialization code. It actually selects a board depending on the detected
sensor type only, with the result that 3 of the 6 webcam boards are currently
dead.
Separate it and move it to em28xx_hint_board() which already contains the board
hints for analog capturing+TV and DVB devices.
This way, we have all board hints at a common place which makes it easier
to extend the code and reduces the risk of regressions.
It also makes it possible again to use the boards EM2750_BOARD_DLCW_130,
EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module
parameter "card").
NOTE: the current board hint logic for webcams is preserved. Not more not less.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices without DVB support (such as the "Terratec Grabby" and
"Easycap DC-60") provide isochronous DVB USB endpoints with wMaxPacketSize set
to 0 bytes for all alt settings.
Ignore these endpoints and avoid registering a DVB device node and loading the
DVB driver extension.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver writes the output resolution to registers 0x34 (width / 16)
and 0x35 (height / 16) always.
We don't know yet what these registers are used for.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming doesn't work with the EM2765 if bit 5 of the output format register
0x27 is set.
It's actually not clear if really has to be set for the other chips, but for
now let's keep it to avoid regressions and add a comment to the code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em25xx/em276x/em277x/em278x frame data format is different to the one used
by the em2710/em2750/em28xx chips.
With the recent cleanups and reorganization of the frame data processing code it
can be easily extended to support these devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam "SpeedLink VAD Laplace" (em2765 + ov2640) uses a special algorithm
for i2c communication with the sensor, which is connected to a second i2c bus.
We don't know yet how to find out which devices support/use it.
It's very likely used by all em25xx and em276x+ bridges.
Tests with other em28xx chips (em2820, em2882/em2883) show, that this
algorithm always succeeds there although no slave device is connected.
The algorithm likely also works for real i2c client devices (OV2640 uses SCCB),
because the Windows driver seems to use it for probing Samsung and Kodak
sensors.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for vidioc_g_chip_name, allowing AC97 to be implemented as a
second chip on the bridge with the name "ac97". v4l2-dbg can just match the
name with that string in order to detect a ac97-compliant set of registers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit aab3125c43 broke em28xx. I traced
this eventually to the change in what algo_data points to. This pointer
is also passed to em28xx_tuner_callback() through several hidden tuner
layers (yuck!) and that callback was not updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's currently a bug on em28xx-i2c that makes it write the
wrong values to register 06, that controlls the I2C bus speed
and bus.
Fix it to change only the I2C bus flag.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an hybrid board. However, for analog, it requires
a new driver for saa7136. So, for now, let's just add
support for Digital TV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It turned out that some devices return less bytes then requested via i2c when
ALL of the following 3 conditions are met:
- i2c bus B is used
- there was no attempt to write to the specified slave address before
- no device present at the specified slave address
With the current code, this triggers an -EIO error and prints a message to the
system log.
Because it can happen very often during device probing, it is better to ignore
this error and bail out silently after the follwing i2c transaction success
check with -ENODEV.
[mchehab@redhat.com: a small CodingStyle fix]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver obtains the timestamps using function v4l2_get_timestamp(),
which produces a montonic timestamp.
Fixes the warnings appearing in the system log since commit 6aa69f99
"[media] vb2: Add support for non monotonic timestamps"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer