There is currently a small window during which the SYSTEMPORT adapter
enables its RX interrupts without having enabled its NAPI handler, which
can result in packets to be discarded during interface bringup.
A similar but more serious window exists in bcm_sysport_resume() during
which we can have the RDMA engine not fully prepared to receive packets
and yet having RX interrupts enabled.
Fix this my moving the RX interrupt enable down to
bcm_sysport_netif_start() after napi_enable() for the RX path is called,
which fixes both call sites: bcm_sysport_open() and
bcm_sysport_resume().
Fixes: b02e6d9ba7 ("net: systemport: add bcm_sysport_netif_{enable,stop}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple enable_irq_wake() calls will keep increasing the IRQ
wake_depth, which ultimately leads to the following types of
situation:
1) enable Wake-on-LAN interrupt w/o password
2) enable Wake-on-LAN interrupt w/ password
3) enable Wake-on-LAN interrupt w/o password
4) disable Wake-on-LAN interrupt
After step 4), SYSTEMPORT would always wake-up the system no matter what
wake-up device we use, which is not what we want. Fix this by making
sure there are no unbalanced enable_irq_wake() calls.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit bc23333ba1 ("net:
bcmgenet: fix bcmgenet_put_tx_csum()"), we need to return the skb
pointer in case we had to reallocate the SKB headroom.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.
The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.
Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we bring the interface down, phy_stop() will schedule the PHY
state machine to call our link adjustment callback. By the time we do so,
we may have clock gated off the SYSTEMPORT hardware block, and this will
cause bus errors to happen in bcm_sysport_adj_link():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
This is a similar fix to the GENET one:
c677ba8b3c ("net: bcmgenet: update
UMAC_CMD only when link is detected").
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Broadcom tags are enabled, e.g: when interfaced to an Ethernet
switch, make sure that we tell the RXCHK engine that it should be
expecting a 4-bytes Broadcom tag after the Ethernet MAC Source Address.
Use netdev_uses_dsa() to check for that condition since that will tell
us if a switch is attached to our network interface.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged two uses of kzalloc() for allocating and zeroing
arrays, use kcalloc() instead as recommended.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged a bunch of: "CHECK: Alignment should match open
parenthesis" problems, fix all of them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:
- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us
The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This boolean tells us whether we are using the RXCHK hardware block,
so use a variable name that reflects that. RXCHK might be used in the
future to implement Wake-on-LAN using ARP or unicast packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware recommended suspend/resume procedure for
SYSTEMPORT. We leverage the previous factoring work such that we can
logically break all suspend/resume operations into disctint RX and TX
code paths.
When the system enters S3, we will loose all register contents, so
make sure that we correctly re-program all the hardware and software
views of the RX & TX rings as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor common code that either enables or disables the network
interface with the networking stack. We are going to reuse these
functions for suspend/resume callbacks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite often we need to enable either the transmitter or the receiver
bits in UMAC_CMD, use umac_enable_set() to do that for us.
This is a preliminary change to introduce suspend/resume support in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we do not limit the number of packets the TX completion
function bcm_sysport_tx_reclaim() is allowed to reclaim, we were still
using its return value as-is. This means that we could hit the WARN() in
net/core/dev.c where work_done >= budget.
Make sure we do exit the NAPI context when the TX ring is empty, and
pretend there was no work to do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UniMAC CMD_SW_RESET bit is not a self-clearing bit, so we need to
assert it, wait a bit and clear it manually. As a result, umac_reset()
is updated not to return any value. The previous version of the code
simply wrote 0 to the CMD register, which would make the busy-waiting
loop exit immediately, having zero effect.
By writing 0 to the CMD register, we were clearing all bits in the CMD
register, and not using the hardware reset default values which are
set on purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT Ethernet MAC supports multicast just fine, it just lacks
any sort of Unicast/Broadcast/Multicasting filtering at the Ethernet MAC
level since that is handled by the front end Ethernet switch, but that
is properly handled by bcm_sysport_set_rx_mode().
Some user-space applications might be relying on the presence of this
flag to prevent using multicast sockets, this also prevents that
interface from joining the IPv6 all-router mcast group.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix:
CC drivers/net/ethernet/broadcom/bcmsysport.o
In file included from drivers/net/ethernet/broadcom/bcmsysport.c:28:0:
drivers/net/ethernet/broadcom/bcmsysport.h:41:8: error: redefinition of 'struct tsb'
arch/sparc/include/asm/mmu_64.h:65:8: note: originally defined here
make[1]: *** [drivers/net/ethernet/broadcom/bcmsysport.o] Error 1
we change struct tsb to struct bcm_tsb in the broadcom driver in
order to avoid the namespace collision. For consistency, we also
change struct rsb to struct bcm_rsb, so the Rx/Tx symmetry is
maintained.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When umac_enable_set() is used to disable the UniMAC receiver or
transmitter, we need to make sure that we wait for a full-sized packet
to be processed because the UniMAC hardware stops on a packet boundary,
not immediately.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_unmap_single() was called with dma_unmap_len(cb, dma_len),
unfortunately we failed to assign this length field in
bcm_sysport_rx_refill() or bcm_sysport_alloc_rx_bufs() using
dma_unmap_len_set().
This causes packet contents corruption because are we not invoking the
cache invalidation routines with the proper length. Fix this by using
the full RX buffer size (RX_BUF_LENGTH) because the mappings for the RX
bufers are created with that size.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets need to be at least 64 bytes to enter the switch port logic,
including the FCS, otherwise they will be discarded as RUNT packets.
With packets having Broadcom tags, the 4-bytes tag is first stripped
off the packet, and the packet length is then checked, so we need to
make sure that the packet length with FCS is at least 64 bytes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link adjustment callback can be called as frequently as desired by
the PHY library, as such, let's avoid doing a Read/Modify/Write sequence
if nothing changed, which is more than likely since we are interfaced
with a switch device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT is the latest Ethernet MAC hardware block used on newer
BCM7xxx Set Top Box SoCs in conjunction with an internal Ethernet
switch. This patch adds support for this hardware block along with the
following hardware features:
- support for hardware checksum offload (transmit and receive)
- support for the 32 transmit queues
- MIB counters reading
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli