The Freescale DIU video controller supports five video "modes", but only
the first two are used by the driver. The other three are special modes
that don't make sense for a framebuffer driver. Therefore, there's no
point in keeping a global variable that indicates which mode we're
supposed to use.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Instead of using ill-defined numbers (0, 1, and 2) for the monitor port, allow
the user to specify the port by name ("dvi", "lvds", or "dlvds"). This works
on the kernel command line, the module command-line, and the sysfs "monitor"
device.
Note that changing the monitor port does not currently work on the P1022DS,
because the code that talks to the PIXIS FPGA is broken.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
MPC5121 DIU configuration/setup as initialized by the boot
loader currently will get lost while booting Linux. As a
result displaying the boot splash is not possible through
the boot process.
To prevent this we reserve configured DIU frame buffer
address range while booting and preserve AOI descriptor
and gamma table so that DIU continues displaying through
the whole boot process. On first open from user space
DIU frame buffer driver releases the reserved frame
buffer area and continues to operate as usual.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since PSC could also be used in other modes than UART mode
we move PSC FIFO memory initialization from serial driver to
common platform code. The initialized FIFO memory slices may
not overlap, so the most easy way would be to configure them
all at once at init time for all PSC devices. This is now done
by this patch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Instantiate NAND Flash Controller device if it's
description is found in the device tree.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add reset module registers representation and
machine restart callback for mpc5121 platform.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move mpc5121_clk_init() call to platform init code so it won't
get called on non-5121 platforms on a multiplatform kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move shared code from mpc5121_ads.c to new file mpc512x_shared.c
- mpc512x_find_ips_freq -> unchanged
- contents of mpc5121_ads_init_IRQ -> mpc512x_init_IRQ
- looking for fsl,mpc5121-ipic instead of fsl,ipic
- mpc5121_ads_declare_of_platform_devices -> mpc5121_declare_of_platform_devices
- and use compatible for lookup instead of node name
Add new generic board setup mpc5121_generic.c
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Timur Tabi