This driver supports a subset of HP Smart Array Controllers.
It is a SCSI alternative to the cciss driver.
[akpm@linux-foundation.org: avoid helpful cleanup patches]
[achiang@hp.com: make device attrs static]
[akpm@linux-foundation.org: msleep() does set_current_state() itself]
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use libfcoe as a common FIP implementation with fcoe.
FIP or non-FIP mode is fully automatic if the firmware
supports and enables it.
Even if FIP is not supported, this uses libfcoe for the non-FIP
handling of FLOGI and its response.
Use the new lport_set_port_id() notification to capture
successful FLOGI responses and port_id resets.
While transitioning between Ethernet and FC mode, all rx and
tx FC frames are queued. In Ethernet mode, all frames are
passed to the exchange manager to capture FLOGI responses.
Change to set data_src_addr to the ctl_src_addr whenever it
would have previously been zero because we're not logged in.
This seems safer so we'll never send a frame with a 0 source MAC.
This also eliminates a special case for sending FLOGI frames.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is a driver for VMware's paravirtualized SCSI device,
which should improve disk performance for guests running
under control of VMware hypervisors that support such devices.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This driver supports PMC-Sierra PCIe SAS/SATA 8x6G SPC 8001 chip based
host adapters.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[v2: fixed up virt_to_bus() issue spotted by sfr]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
People keep sending patches to expose CONFIG_SCSI_WAIT_SCAN as a tunable
item. These patches aren't accepted upstream, so let's stop the ongoing
irritation of people due to the unconditionally installed module and its
Kconfig symbol.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
New iSCSI driver for Broadcom BNX2 devices. The driver interfaces with
the CNIC driver to access the hardware.
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I had to set CONFIG_SCSI_MULTI_LUN to y in order to get my SE W595
working when plugging it as a mass storage. Looking at SCSI option to
get a phone behaving correctly was convoluted to say the least. There
are quite a few other reports about USB card readers needing this option
as well. This patch improves the help text to make the use of the option
more obvious.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Zero functional changes, just file movement.
This commit prepares for the upcoming integration of the
Marvell-provided driver update that splits the driver into support
for both 64xx and 94xx chip families.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fnic is a driver for the Cisco PCI-Express FCoE HBA
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mention ATAPI. We could insert an essay about libata and ide-scsi etc but
the failure case is someone enables it which is just fine so keep it
simple.
(Revised text from suggestion by Matthew Wilcox)
Closes#7736
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just sets up build environment for libfcoe module towards a
libfcoe library for libfc LLDs using FCoE as libfc transport.
Common library code to libfcoe is added in next patch.
Also, updated MODULE_LICENSE from "GPL" string to "GPL v2" for
libfc, libfcoe and fcoe modules to accurately match the licenses.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* This is new scsi lld device driver from LSI supporting the SAS 2.0
standard. I have split patchs by filename.
* Here is list of new 6gb host controllers:
LSI SAS2004
LSI SAS2008
LSI SAS2108
LSI SAS2116
* Here are the changes in the 4th posting of this patch set:
(1) fix compile errors when SCSI_MPT2SAS_LOGGING is not enabled
(2) add mpt2sas to the SCSI Mid Layer Makefile
(3) append mpt2sas_ to the naming of all non-static functions
(4) fix oops for SMP_PASSTHRU
(5) doorbell algorithm imported changes from windows driver
* Here are the changes in the 3rd posting of this patch set:
(1) add readl following writel from the function that disables interrupts
(2) replace 0xFFFFFFFFFFFFFFFFULL with ~0ULL
(3) when calling pci_enable_msix, only pass one msix entry (instead of 15).
(4) remove the "current HW implementation uses..... " comment in the sources
(5) merged bug fix for SIGIO/POLLIN notifcation; reported by the storlib team.
* Here are the changes in the 2nd posting of this patch set:
(1) use little endian types in the mpi headers
(2) merged in bug fix's from inhouse drivers.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Tested-by: peter Bogdanovic <pbog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
OSD in kernel source code is assumed to be at:
drivers/scsi/osd/ with its own Makefile and Kconfig
Add includes to them from drivers/scsi Makefile and Kconfig
Add OSD to MAINTAINERS file
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Kconfig entry for SCSI_LOGGING refers the reader to
drivers/scsi/scsi.c, but I didn't find any useful information
there. There is certainly logging code in that file, but the
logging types and logging levels are described in
drivers/scsi/scsi_logging.h.
Also, the procfs file referred to in the section is incorrect.
It should be /proc/sys/dev/scsi/logging_level and not
/proc/scsi/scsi.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libfc uses crc32 functions, so cause it to be built
via select:
drivers/built-in.o: In function `fc_frame_crc_check':
(.text+0x75dae): undefined reference to `crc32_le'
drivers/built-in.o: In function `fc_fcp_recv':
fc_fcp.c:(.text+0x7b919): undefined reference to `crc32_le'
fc_fcp.c:(.text+0x7b9d5): undefined reference to `crc32_le'
fc_fcp.c:(.text+0x7ba54): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix scsi_debug build error:
drivers/built-in.o: In function `resp_read':
scsi_debug.c:(.text+0x21379a): undefined reference to `crc_t10dif'
drivers/built-in.o: In function `resp_write':
scsi_debug.c:(.text+0x213fca): undefined reference to `crc_t10dif'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iSeries dependent drivers fail to build, when CONFIG_VIOPATH is disabled.
Fix the problem by making those drivers select it.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As planed, this removes ide-scsi.
The 2.6 kernel supports direct writing to ide CD drives, which
eliminates the need for ide-scsi. ide-scsi has been unmaintained and
marked as deprecated.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James.Bottomley@HansenPartnership.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
fcoe selects libfc and requires SCSI and PCI (the SCSI requirement is
implicitly covered by an enclosing if). Fix them both up so they
cannot be configured in an invalid state: make LIBFC select
SCSI_FC_ATTRS and make FCOE depend on PCI and select LIBFC.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch implements the cxgb3i iscsi connection acceleration for the
open-iscsi initiator.
The cxgb3i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Encapsulation protocol for running Fibre Channel over Ethernet interfaces.
Creates virtual Fibre Channel host adapters using libfc.
This layer is the LLD to the scsi-ml. It allocates the Scsi_Host, utilizes
libfc for Fibre Channel protocol processing and interacts with netdev to
send/receive Ethernet packets.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libFC is composed of 4 blocks supported by an exchange manager
and a framing library. The upper 4 layers are fc_lport, fc_disc,
fc_rport and fc_fcp. A LLD that uses libfc could choose to
either use libfc's block, or using the transport template
defined in libfc.h, override one or more blocks with its own
implementation.
The EM (Exchange Manager) manages exhcanges/sequences for all
commands- ELS, CT and FCP.
The framing library frames ELS and CT commands.
The fc_lport block manages the library's representation of the
host's FC enabled ports.
The fc_disc block manages discovery of targets as well as
handling changes that occur in the FC fabric (via. RSCN events).
The fc_rport block manages the library's representation of other
entities in the FC fabric. Currently the library uses this block
for targets, its peer when in point-to-point mode and the
directory server, but can be extended for other entities if
needed.
The fc_fcp block interacts with the scsi-ml and handles all
I/O.
Signed-off-by: Robert Love <robert.w.love@intel.com>
[jejb: added include of delay.h to fix ppc64 compile prob spotted by sfr]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch removes the Hades support that was marked as BROKEN 5 years ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This option was forgotten when the SCSI_QLOGIC_FC driver was removed.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Support for controllers and disks that implement DIF protection
information:
- During command preparation the RDPROTECT/WRPROTECT must be set
correctly if the target has DIF enabled.
- READ(6) and WRITE(6) are not supported when DIF is on.
- The controller must be told how to handle the I/O via the
protection operation field in scsi_cmnd.
- Refactor the I/O completion code that extracts failed LBA from the
returned sense data and handle DIF failures correctly.
- sd_dif.c implements the functions required to prepare and complete
requests with protection information attached.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds a new device driver to support the Virtual Fibre Channel
interface on IBM Power based servers. The Virtual I/O Server on IBM Power
servers utilizes N-Port ID Virtualization to export a Virtual Fibre Channel
adapter to the client. This driver is the client device driver.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The module name was changed from esp to sun_esp some time ago.
Also correct the list of chips supported by the driver.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some of the storage devices (that can be accessed through multiple paths),
do need some special handling for
1. Activating the passive path of the storage access.
2. Decode and handle the special sense codes returned by the devices.
3. Handle the I/Os being sent to the passive path, especially
during the device probe time.
when accessed through multiple paths.
As of today this special device handling is done at the dm-multipath
layer using dm-handlers. That works well for (1); for (2) to be handled
at dm layer, scsi sense information need to be exported from SCSI to dm-layer,
which is not very attractive; (3) cannot be done at all at the dm layer.
Device handler has been moved to SCSI mainly to handle (2) and (3) properly.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The new mac_esp scsi driver needs CONFIG_SCSI_SPI_ATTRS, just like all other
drivers using the new esp_scsi core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the code to actually support 64 bit platforms. 64 bit
DMA is enabled on both x86_32 PAE and 64 bit platforms.
This code is based in part on the unofficial adaptec 64-bit
dpt_i2o driver update that I got from Mark Salyzyn at Adaptec.
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Replace the mac_esp driver with a new one based on the esp_scsi core.
For esp_scsi: add support for sync transfers for the PIO mode, add a new
esp_driver_ops method to get the maximum dma transfer size (like the old
NCR53C9x driver), and some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We've verified that there are 64 bit and endianness problems in the
flashpoint driver. Reverse the logic of CONFIG_OMIT_FLASHPOINT (make
it CONFIG_SCSI_FLASHPOINT) and make it depend on X86_32 so it can't
appear for any other architectures. Long term, if someone chooses,
they could make FlashPoint 64 bit compliant (it looks like its a
question of fixing up the sizes in some of the packed descriptors)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We have several drivers that don't list SCSI as a dependency in
Kconfig. That leads to them potentially being selected as Y even if
SCSI is M (which will produce a build failure). Fix this by making
the if SCSI_LOWLEVEL that goes around all the drivers a tristate
forcing them all automatically to inherit the value of SCSI.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix compilation warning in gdth.c, which was using the deprecated
pci_find_device.
drivers/scsi/gdth.c:645: warning: 'pci_find_device' is deprecated (declared at include/linux/pci.h:495)
Changing it to use pci_get_device, instead.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds support to SCSI for enclosure services devices. It also makes
use of the enclosure services added in an earlier patch to display the
enclosure topology in sysfs.
At the moment, the enclosures are SAS specific, but if anyone actually
has a non-SAS enclosure that follows the SES-2 standard, we can add that
as well.
On my Vitesse based system, the enclosures show up like this:
sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/
total 0
-r--r--r-- 1 root root 4096 2008-02-03 15:44 components
lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005
lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure
--w------- 1 root root 4096 2008-02-03 15:44 uevent
And the individual occupied slots like this:
sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/
total 0
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 active
lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 status
lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component
-r--r--r-- 1 root root 4096 2008-02-03 15:45 type
--w------- 1 root root 4096 2008-02-03 15:45 uevent
You can flash the various blinky lights by echoing to the fault and locate files.
>From the device's point of view, you can see it has an enclosure like this:
sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/
block:sda generic queue_depth state
bsg:0:0:0:0 iocounterbits queue_type subsystem
bus iodone_cnt rescan timeout
delete ioerr_cnt rev type
device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent
driver modalias scsi_disk:0:0:0:0 vendor
enclosure_component:SLOT 001 model scsi_generic:sg0
evt_media_change power scsi_level
Note the enclosure_component:SLOT 001 which shows where in the enclosure
this device fits.
The astute will notice that I'm using SCSI VPD Inquiries to identify the
devices. This, unfortunately, won't work for SATA devices unless we do
some really nasty hacking about on the SAT because the only think that
knows the SAS addresses for SATA devices is libsas, not libata where the
SAT resides.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These drivers depend on the deprecated NCR53C9X core and need to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Linux/m68k <linux-m68k@vger.kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver depends on the deprecated NCR53C9X core and needs to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver depends on the deprecated NCR53C9X core and needs to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Converted sun3x_esp driver to use esp_scsi.c
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SGI IP28 machines would need special treatment (enable adding addtional
wait states) when accessing memory uncached. To avoid this pain I
changed the driver to use only cached access to memory.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.
README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use open-iscsi.org instead of linux-iscsi.sf.net, which hasn't been
updated for ages.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Most code changes were made to support adapters based on Marvell IOP, plus some
other fixes.
- add more PCI device IDs
- support for adapters based on Marvell IOP
- fix a result code translation error on big-endian systems
- fix resource releasing bug when scsi_host_alloc() fail in hptiop_probe()
- update scsi_cmnd.resid when finishing a request
- correct some coding style issues
[akpm@linux-foundation.org: type fixes]
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Apparently no one wonts this driver, and no one
is willing to fix it for future changes to SCSI.
So remove it, and if someone wants it in the future
He can revive it with the needed fixes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The psi240i driver is still written for cmnd->request_buffer
as a char pointer to actual data. There was never any attempt
to use the scatterlist option.
- remove all source files (3) from drivers/scsi
- Remove from Makefile and Kconfig
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change PortAddr to be an unsigned int instead of an unsigned short (IO
Port address are 24 bit on parisc). Fix a couple of printk argument
warnings. Remove the Kconfig marking as 'BROKEN'.
I haven't removed the #warning yet because virt_to_bus/bus_to_virt are
only eliminated for narrow boards. Wide boards need more work.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Description:
** support ARC1200/1201/1202 SATA RAID adapter, which is named
ACB_ADAPTER_TYPE_B
** modify the arcmsr_pci_slot_reset function
** modify the arcmsr_pci_ers_disconnect_forepart function
** modify the arcmsr_pci_ers_need_reset_forepart function
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support like the srp transport does:
- fc_remote_port_{rolechg,delete} calls
scsi_tgt_it_nexus_{create,destroy} for target drivers.
- add callbacks to notify target drivers of the nexus and tmf
operation results to fc_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
it's better to remove tgt dependencies in srp transport class since
most people want only initiator support.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts libsrp and ibmvstgt to use srp transport.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support:
- srp_rport_{add,del} calls scsi_tgt_it_nexus_{create,destroy} for
target drivers.
- add a callback to notify target drivers of the nexus operation
results to srp_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts ibmvscsi to use the srp transport class.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds srp transport class that works with ib_srp and ibmvscsi.
It creates only /sys/class/{srp_host,srp_remote_ports} and
srp_remote_ports has only "port_id" attribute.
viola:/sys/class/srp_remote_ports/port-0:1# ls
device port_id subsystem uevent
viola:/sys/class/srp_remote_ports/port-0:1# cat port_id
4c:49:4e:55:58:20:56:49:4f:00:00:00:00:00:00:00
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce CONFIG_CHECK_SIGNATURE to control inclusion of check_signature()
and avoid problems on platforms that don't have readb().
Let the few legacy (ISA || PCI || X86) drivers that need check_signature()
select CONFIG_CHECK_SIGNATURE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k: Fix a few hickups in drivers/scsi/Kconfig
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sas transport class attaches one bsg device to every SAS object
(host, device, expander, etc). LLDs can define a function to handle
SMP requests via sas_function_template::smp_handler.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some offending drivers depend on it and set CONFIG_ARCH_NO_VIRT_TO_BUS
for ppc64 so that we don't build those drivers.
This gets PowerPC allmodconfig and allyesconfig much closer to building.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Not converted to the 2.6 kconfig system and no code in the tree.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With
dma-mapping-prevent-dma-dependent-code-from-linking-on.patch
scsi fails to build on !HAS_DMA architectures:
drivers/built-in.o(.text+0x20af6): In function `scsi_dma_map':
: undefined reference to `dma_map_sg'
drivers/built-in.o(.text+0x20b5c): In function `scsi_dma_unmap':
: undefined reference to `dma_unmap_sg'
I split those functions out into a new file. Builds on s390 and i386.
Move scsi_dma_{map,unmap} into scsi_lib_dma.c which is only build if
HAS_DMA is set.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, 11 Jun 2007 20:28:16 +0200 api wrote:
> Good day,
> When doing make menuconfig one comes across CONFIG_BLK_DEV_SD.
> The help file states that this is for scsi disks.NO MENTION IS MADE THAT
> IT IS NEEDE FOR SATA DISKS AS WELL!
> Would have saved me a lot of time if the help was up to date.
> I hope this can be changed so others can make a kernel for sata systems
> quicker.
From: Randy Dunlap <randy.dunlap@oracle.com>
Add help info for BLK_DEV_SD referring to its use in
SATA or PATA driver configurations.
Add help text for "ATA" indicating that it probably needs
some SCSI config symbols enabled in order to be useful.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New driver for Amiga Zorro bus NCR53c710 SCSI controllers, using the 53c700
SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the Amiga 4000T built-in NCR53c710 SCSI controller, using the
53c700 SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the MVME16x NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the BVME6000 NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add m68k support to the 53c700 SCSI driver
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is basically a straight conversion. I have one of these things, so
I know it works ... my problem is that it has a wierd SCA like
connector, so I can't connect anything to it (no cables).
However, previously it panic'd in the interrupt, now it completes a bus
scan.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
SCSI should be working on a TT (but someone should really try!) but causes
trouble on a Falcon (as in: it ate a filesystem of mine) at least when
used concurrently with IDE. I have the notion it's because locking of the
ST-DMA interrupt by IDE is broken in 2.6 (the IDE driver always complains
about trying to release an already-released ST-DMA). Needs more work, but
that's on the IDE or m68k interrupt side rather than SCSI.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.
Signed-off-by: Alexander E. Patrakov
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Major features:
1) Tagged queuing support.
2) Will properly negotiate for synchronous transfers even on
devices that reject the wide negotiation message, such as
CDROMs
3) Significantly lower kernel stack usage in interrupt
handler path by elimination of function vector arrays,
replaced by a top-level switch statement state machine.
4) Uses generic scsi infrastructure as much as possible to
avoid code duplication.
5) Automatic request of sense data in response to CHECK_CONDITION
6) Portable to other platforms using ESP such as DEC and Sun3
systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unused SCSI-related kernel config variables
SCSI_NCR53C8XX_PROFILE_SUPPORT
SCSI_NCR53C8XX_PROFILE
53C700_IO_MAPPED
AIC79XX_ENABLE_RD_STRM
AIC7XXX_PROBE_EISA_VL
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently scsi_wait_scan is only built modular if SCSI is modular.
However, it's perfectly possible for a built in SCSI still to have
modular drivers and thus need scsi_wait_scan as a module. Therefore,
scsi_wait_scan should always be built as a module (unless the kernel
doesn't support modules).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Apparently the driver compiles and runs, so tidy up some macro warnings
and bring it back as unBROKEN.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>