side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
The watchdog pclk is controlled from the secure GRF but we still
want to mention it explicitly to not use arbitary parent clocks
in the devicetree wdt node, so add a SGRF_GATE for it.
Suggested-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the boilerplate code for manual addition of the watchdog clock
to the new SGRF_GATE macro for all affected socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some clk gates on Rockchip SoCs are part of the SGRF (secure general
register files) and thus only controllable from secure mode, with the
most prominent example being the watchdog.
In most cases we still want to define this as a real clock though,
to have complete clock tree and not reference the generic base-clock
from the devicetree.
So far we've just defined this as factor-1-1 clocks in the clock init,
so define a special clock-type for it so that this definition can be
part of the general tree-definition and save some boilerplate code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 48 MHz PLL rate is not present in the downstream chromeos-3.14
tree. Looking at history, it was originally removed in
<https://crrev.com/c/265810> ("CHROMIUM: clk: rockchip: expand more
clocks support") with no explanation. Much of that patch was later
reverted in <https://crrev.com/c/284595> ("CHROMIUM: clk: rockchip:
Revert more questionable PLL rates"), but that patch left in the
removal of 48 MHz. What I wrote in that patch:
> Note that the original change also removed the rate (48000000, 1,
> 64, 32) from the table. I have no idea why that was squashed in
> there, but that rate was invalid anyway (it appears to have an out
> of bounds NO). I'm not putting that rate in.
Reading the TRM I see that NO is defined as
- NO: 1, 2-16 (even only)
...and furthermore only 4 bits are assigned for NO-1, which means that
the highest NO we could even represent is 16.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing 1.464GHz clock rate to rk3228_cpuclk_rates[], which gets
referenced in the operating points but wasn't defined till now.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There's a bit of math in rockchip_mmc_get_phase() to calculate the
"fine delay". This math boils down to:
PSECS_PER_SEC = 1000000000000.
ROCKCHIP_MMC_DELAY_ELEMENT_PSEC = 60
card_clk * ROCKCHIP_MMC_DELAY_ELEMENT_PSEC * 360 * x / PSECS_PER_SEC
...but we do it in pieces to avoid overflowing 32-bits. Right now we
overdo it a little bit, though, and end up getting less accurate math
than we could. Right now we do:
DIV_ROUND_CLOSEST((card_clk / 1000000) *
(ROCKCHIP_MMC_DELAY_ELEMENT_PSEC / 10) *
(360 / 10) *
delay_num,
PSECS_PER_SEC / 1000000 / 10 / 10)
This is non-ideal because:
A) The pins on Rockchip SoCs are rated to go at most 150 MHz, so the
max card clock is 150 MHz. Even ignoring this the maximum SD card
clock (for SDR104) would be 208 MHz. This means you can decrease
your division by 100x and still not overflow:
hex(208000000 / 10000 * 6 * 36 * 0xff) == 0x44497200
B) On many Rockchip SoCs we end up with a card clock that is actually
148500000 because we parent off the 297 MHz PLL. That means the
math we're actually doing today is less than ideal. Specifically:
148500000 / 1000000 = 148
Let's fix the math to be slightly more accurate.
NOTE: no known problems are fixed by this. It was found simply by
code inspection. If you want to see the difference between the old
and the new on a 148.5 MHz clock, this python can help:
old = [x for x in
(int(round(148 * 6 * 36 * x / 10000.)) for x in range(256))
if x < 90]
new = [x for x in
(int(round(1485 * 6 * 36 * x / 100000.)) for x in range(256))
if x < 90]
The only differences are:
delay_num=17 54=>55
delay_num=22 70=>71
delay_num=27 86=>87
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
At boot time, my rk3288-veyron devices yell with 8 lines that look
like this:
[ 0.000000] rockchip_mmc_get_phase: invalid clk rate
This is because the clock framework at clk_register() time tries to
get the phase but we don't have a parent yet.
While the errors appear to be harmless they are still ugly and, in
general, we don't want yells like this in the log unless they are
important.
There's no real reason to be yelling here. We can still return
-EINVAL to indicate that the phase makes no sense without a parent.
If someone really tries to do tuning and the clock is reported as 0
then we'll see the yells in rockchip_mmc_set_phase().
Fixes: 4bf59902b5 ("clk: rockchip: Prevent calculating mmc phase if clock rate is zero")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When calculating the MMC phase we can just use clk_hw_get_rate()
instead of clk_get_rate(). This avoids recalculating the rate.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Mark UFS clk as critical on Hi-Silicon hi3660 SoCs
- Support for Cirrus Logic Lochnagar clks
* clk-hisi:
clk: hi3660: Mark clk_gate_ufs_subsys as critical
* clk-lochnagar:
clk: lochnagar: Add support for the Cirrus Logic Lochnagar
clk: lochnagar: Add initial binding documentation
* clk-allwinner:
clk: sunxi-ng: sun5i: Export the MBUS clock
clk: sunxi-ng: a83t: Add pll-video0 as parent of csi-mclk
clk: sunxi-ng: h6: Allow video & vpu clocks to change parent rate
clk: sunxi-ng: h6: Preset hdmi-cec clock parent
clk: sunxi: Add Kconfig options
clk: sunxi-ng: f1c100s: fix USB PHY gate bit offset
clk: sunxi-ng: Allow DE clock to set parent rate
* clk-rockchip:
clk: rockchip: undo several noc and special clocks as critical on rk3288
clk: rockchip: add a COMPOSITE_DIV_OFFSET clock-type
clk: rockchip: Turn on "aclk_dmac1" for suspend on rk3288
clk: rockchip: Limit use of USB PHY clock to USB on rk3288
clk: rockchip: Fix video codec clocks on rk3288
clk: rockchip: Make rkpwm a critical clock on rk3288
clk: rockchip: fix wrong clock definitions for rk3328
* clk-qoriq:
clk: qoriq: increase array size of cmux_to_group
dt-bindings: qoriq-clock: Add ls1028a chip compatible string
clk: qoriq: Add ls1028a clock configuration
clk: qoriq: add more PLL divider clocks support
dt-bindings: qoriq-clock: add more PLL divider clocks support
Now that clk_{readl,writel} is just an alias for {readl,writel}, we can
switch all users of clk_* to use the accessors directly and remove the
helpers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[sboyd@kernel.org: Also convert renesas file so that this can be
compile independently]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is mostly a revert of commit 55bb6a633c ("clk: rockchip: mark
noc and some special clk as critical on rk3288") except that we're
keeping "pmu_hclk_otg0" as critical still.
NOTE: turning these clocks off doesn't seem to do a whole lot in terms
of power savings (checking the power on the logic rail). It appears
to save maybe 1-2mW. ...but still it seems like we should turn the
clocks off if they aren't needed.
About "pmu_hclk_otg0" (the one clock from the original commit we're
still keeping critical) from an email thread:
> pmu ahb clock
>
> Function: Clock to pmu module when hibernation and/or ADP is
> enabled. Must be greater than or equal to 30 MHz.
>
> If the SOC design does not support hibernation/ADP function, only have
> hclk_otg, this clk can be switched according to the usage of otg.
> If the SOC design support hibernation/ADP, has two clocks, hclk_otg and
> pmu_hclk_otg0.
> Hclk_otg belongs to the closed part of otg logic, which can be switched
> according to the use of otg.
>
> pmu_hclk_otg0 belongs to the always on part.
>
> As for whether pmu_hclk_otg0 can be turned off when otg is not in use,
> we have not tested. IC suggest make pmu_hclk_otg0 always on.
For the rest of the clocks:
atclk: No documentation about this clock other than that it goes to
the CPU. CPU functions fine without it on. Maybe needed for JTAG?
jtag: Presumably this clock is only needed if you're debugging with
JTAG. It doesn't seem like it makes sense to waste power for every
rk3288 user. In any case to do JTAG you'd need private patches to
adjust the pinctrl the mux the JTAG out anyway.
pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two
clocks on only during kernel panics in order to access some coresight
registers. Since nothing in the upstream kernel does this we should
be able to leave them off safely. Maybe also needed for JTAG?
hsicphy12m_xin12m: There is no indication of why this clock would need
to be turned on for boards that don't use HSIC.
pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn
these 4 clocks on only when doing DDR transitions and they are off
otherwise. I see no reason why they'd need to be on in the upstream
kernel which doesn't support DDRFreq.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The div offset of some clocks are different from their mux offset
and the COMPOSITE clock-type require that div and mux offset are
the same, so add a new COMPOSITE_DIV_OFFSET clock-type to handle that.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Experimentally it can be seen that going into deep sleep (specifically
setting PMU_CLR_DMA and PMU_CLR_BUS in RK3288_PMU_PWRMODE_CON1)
appears to fail unless "aclk_dmac1" is on. The failure is that the
system never signals that it made it into suspend on the GLOBAL_PWROFF
pin and it just hangs.
NOTE that it's confirmed that it's the actual suspend that fails, not
one of the earlier calls to read/write registers. Specifically if you
comment out the "PMU_GLOBAL_INT_DISABLE" setting in
rk3288_slp_mode_set() and then comment out the "cpu_do_idle()" call in
rockchip_lpmode_enter() then you can exercise the whole suspend path
without any crashing.
This is currently not a problem with suspend upstream because there is
no current way to exercise the deep suspend code. However, anyone
trying to make it work will run into this issue.
This was not a problem on shipping rk3288-based Chromebooks because
those devices all ran on an old kernel based on 3.14. On that kernel
"aclk_dmac1" appears to be left on all the time.
There are several ways to skin this problem.
A) We could add "aclk_dmac1" to the list of critical clocks and that
apperas to work, but presumably that wastes power.
B) We could keep a list of "struct clk" objects to enable at suspend
time in clk-rk3288.c and use the standard clock APIs.
C) We could make the rk3288-pmu driver keep a list of clocks to enable
at suspend time. Presumably this would require a dts and bindings
change.
D) We could just whack the clock on in the existing syscore suspend
function where we whack a bunch of other clocks. This is particularly
easy because we know for sure that the clock's only parent
("aclk_cpu") is a critical clock so we don't need to do anything more
than ungate it.
In this case I have chosen D) because it seemed like the least work,
but any of the other options would presumably also work fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The USB PHY clock can be configured as (grand) parent of uart0_sclk and
sclk_gpu. It has been observed that UART0 doesn't work reliably in high
speed mode with the PHY clock as input when certain USB devices are
plugged to the USB HOST1 port (see https://crrev.com/c/320543).
Prefix the name of the PHY clock with a '.' in the non-USB muxes to
effectively remove the clock as input from these muxes.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It appears that there is a typo in the rk3288 TRM. For
GRF_SOC_CON0[7] it says that 0 means "vepu" and 1 means "vdpu". It's
the other way around.
How do I know? Here's my evidence:
1. Prior to commit 4d3e84f996 ("clk: rockchip: describe aclk_vcodec
using the new muxgrf type on rk3288") we always pretended that we
were using "aclk_vdpu" and the comment in the code said that this
matched the default setting in the system. In fact the default
setting is 0 according to the TRM and according to reading memory
at bootup. In addition rk3288-based Chromebooks ran like this and
the video codecs worked.
2. With the existing clock code if you boot up and try to enable the
new VIDEO_ROCKCHIP_VPU as a module (and without "clk_ignore_unused"
on the command line), you get errors like "failed to get ack on
domain 'pd_video', val=0x80208". After flipping vepu/vdpu things
init OK.
3. If I export and add both the vepu and vdpu to the list of clocks
for RK3288_PD_VIDEO I can get past the power domain errors, but now
I freeze when the vpu_mmu gets initted.
4. If I just mark the "vdpu" as IGNORE_UNUSED then everything boots up
and probes OK showing that somehow the "vdpu" was important to keep
enabled. This is because we were actually using it as a parent.
5. After this change I can hack "aclk_vcodec_pre" to parent from
"aclk_vepu" using assigned-clocks and the video codec still probes
OK.
6. Rockchip has said so on the mailing list [1].
...so let's fix it.
Let's also add CLK_SET_RATE_PARENT to "aclk_vcodec_pre" as suggested
by Jonas Karlman. Prior to the same commit you could do
clk_set_rate() on "aclk_vcodec" and it would change "aclk_vdpu".
That's because "aclk_vcodec" was a simple gate clock (always gets
CLK_SET_RATE_PARENT) and its direct parent was "aclk_vdpu". After
that commit "aclk_vcodec_pre" gets in the way so we need to add
CLK_SET_RATE_PARENT to it too.
[1] https://lkml.kernel.org/r/1d17b015-9e17-34b9-baf8-c285dc1957aa@rock-chips.com
Fixes: 4d3e84f996 ("clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288")
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Suggested-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Most rk3288-based boards are derived from the EVB and thus use a PWM
regulator for the logic rail. However, most rk3288-based boards don't
specify the PWM regulator in their device tree. We'll deal with that
by making it critical.
NOTE: it's important to make it critical and not just IGNORE_UNUSED
because all PWMs in the system share the same clock. We don't want
another PWM user to turn the clock on and off and kill the logic rail.
This change is in preparation for actually having the PWMs in the
rk3288 device tree actually point to the proper PWM clock. Up until
now they've all pointed to the clock for the old IP block and they've
all worked due to the fact that rkpwm was IGNORE_UNUSED and that the
clock rates for both clocks were the same.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes definition of several clock gate and select register
that is wrong for rk3328 referring to the TRM and vendor kernel.
Also use correct number of softrst registers.
Fix clock definition for:
- clk_crypto
- aclk_h265
- pclk_h265
- aclk_h264
- hclk_h264
- aclk_axisram
- aclk_gmac
- aclk_usb3otg
Fixes: fe3511ad8a ("clk: rockchip: add clock controller for rk3328")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes settings of GPLL frequency in fractional mode for
rk3328. In this mode, FOUTVCO is calcurated by following formula:
FOUTVCO = FREF * FBDIV / REFDIV + ((FREF * FRAC / REFDIV) >> 24)
The problem is in FREF * FRAC >> 24 term. This result always lacks
one from target value is specified by rate member. For example first
itme of rk3328_pll_frac_rate originally has
- rate : 1016064000
- refdiv: 3
- fbdiv : 127
- frac : 134217
- FREF * FBDIV / REFDIV = 1016000000
- (FREF * FRAC / REFDIV) >> 24 = 63999
Thus calculated rate is 1016063999. It seems wrong.
If frac has 134218 (it is increased 1 from original value), second
term is 64000. All other items have same situation. So this patch
adds 1 to frac member in all items of rk3328_pll_frac_rate.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Acked-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the newly added clock-id for PCLK_ACODECPHY to the gate-clock,
so that it gets usable from devicetree.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes definition of I2S1 clock gate register for rk3328.
Current setting is not related I2S clocks.
- bit6 of CRU_CLKGATE_CON0 means clk_ddrmon_en
- bit6 of CRU_CLKGATE_CON1 means clk_i2s1_en
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Similar to commit a9f0c0e563 ("clk: rockchip: fix rk3188 sclk_smc
gate data") there is one other gate clock in the rk3188 clock driver
with a similar wrong ordering, the sclk_mac_lbtest. So fix it as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes the signedness bug returning '(-22)' on the return type by removing the
sanity checker in rockchip_ddrclk_get_parent(). The function should return
and unsigned value only and it's safe to remove the sanity checker as the
core functions that call get_parent like clk_core_get_parent_by_index already
ensures the validity of the clk index returned (index >= core->num_parents).
Fixes: a4f182bf81 ("clk: rockchip: add new clock-type for the ddrclk")
Cc: stable@vger.kernel.org
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add and correct PLL rates for better hdmi output.
This includes minimizing jitter on 213 MHz for better 71 MHz,
250.5 MHz for better 83.5 MHz, 428 MHz for better 25.175 Mhz,
low jitter 273 MHz for better 68.25 mhz, 356 MHz for better 118.68 Mhz
and 300MHz.
Increase the used Fvco for 308, 324 MHz, 292.5 MHz, 273.6 MHz,
238 MHz and 216 MHz.
And add some additional rates allowing to reach better hdmi-related
rates in general.
These match the rates used by ChromeOS, so have been quite widely tested.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PWM2 is commonly used to control voltage of PWM regulator of VDD_LOG in
RK3399. On the Firefly-RK3399 board, PWM2 outputs 40 KHz square wave
from power on and the VDD_LOG is about 0.9V. When the kernel boots
normally into the system, the PWM2 keeps outputing PWM signal.
But the kernel hangs randomly after "Starting kernel ..." line on that
board. When it happens, PWM2 outputs high level which causes VDD_LOG
drops to 0.4V below the normal operating voltage.
By adding "pclk_rkpwm_pmu" to the rk3399_pmucru_critical_clocks array,
PWM clock is ensured to be prepared at startup and the PWM2 output is
normal. After repeated tests, the early boot hang is gone.
This patch works on both Firefly-RK3399 and ROC-RK3399-PC boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Register, shift and mask were wrong according to datasheet.
Fixes: 115510053e ("clk: rockchip: add clock controller for the RK3399")
Cc: stable@vger.kernel.org
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new px30 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The new Rockchip socs have optional half divider:
The formula is shown as:
freq_out = 2*freq_in / (2*div + 3)
Is this the same for all of new SoCs.
So we use "branch_half_divider" + "COMPOSITE_NOMUX_HALFDIV \
DIV_HALF \ COMPOSITE_HALFDIV \ CMPOSITE_NOGATE_HALFDIV"
to hook that special divider clock-type into our clock-tree.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Initially we tried modeling clocks via the devicetree before switching
to clocks declared in the clock drivers and only exporting specific
ids to the devicetree.
As the old code was in the kernel for 1-2 releases when the new mode
of operation was added we kept it for backwards compatibility.
That deprecation notice is in the binding since july 2014, so nearly
4 years now and I think it's time to drop the old cruft.
Especially as at the time using the mainline kernel on Rockchip devices
was not really possible, except for experiments on the really old socs of
the rk3066 + rk3188 line, so there shouldn't be any devicetrees still
around that rely on that code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since hclk_sd and pclk_ddr source clock from CPLL or GPLL,
and these two PLL may change their frequency. If we do not
assign right id to pclk_ddr and hclk_sd, they will alway use
default cur register value, and may get the frequency
exceed their signed off frequency. So assign correct Id
for them, then we can assign frequency for them in dts.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The newly added clock notifier may return an error code but so far the
error output in the function would only return an error pointer from
registering the clock.
So when the clock notifier fails the clock would be unregistered but the
return would still be the clock pointer which could then not be
dereferenced correctly. So fix the error handling to prevent that.
Fixes: 60cf09e45f ("clk: rockchip: Restore the clock phase after the rate was changed")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We can't restore every phase, for instance the invalid phase and
the phase for coming rate which is out of the scope of boards'
ability. And this patch also corrects the error path to return
invalid pointer to clk if clk_notifier_register failed introduced
by the same offending commit.
Fixes: 60cf09e45f ("clk: rockchip: Restore the clock phase after the rate was changed")
Reported-by: wlq <wlq@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: wlq <wlq@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase if
clock rate is zero") catches some gremlins for clk-rk3328.c that the
parents of MMC phase clock should be clk_{sdmmc, sdio, emmc}, but not
sclk_{sdmmc, sdio, emmc}.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase
if clock rate is zero") catches one gremlin again for clk-rk3228.c
that the parent of SDMMC phase clock should be sclk_sdmmc0, but not
sclk_sdmmc. However, the naming of the sdmmc clocks varies in the
manual with the card clock having the 0 while the hclk is named
without appended 0. So standardize one one format to prevent
confusion, as there also is only one (non-sdio) mmc controller on
the soc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We need this rate to generate 100, 200, and 228.57MHz from the same
PLL. 228.57MHz is useful for a pixel clock when the VPLL is used for
an external display.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are many factors affecting the clock phase, including clock
rate, temperature, logic voltage and silicon process, etc. But clock
rate is the most significant one here, and the driver should be aware
of the change of the clock rate. As mmc controller need a fixed phase
after tuning was completed, at least before explicitly doing re-tune,
so this patch try to restore the clock phase by monitoring the event
of rate change.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The MMC sample and drv clock for rockchip platforms are derived from
the bus clock output to the MMC/SDIO card. So it should never happens
that the clk rate is zero given it should inherits the clock rate from
its parent. If something goes wrong and makes the clock rate to be zero,
the calculation would be wrong but may still make the mmc tuning process
work luckily. However it makes people harder to debug when the following
data transfer is unstable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rockchip_clk_register_branch() and rockchip_clk_register_frac_branch()
should free the memory internally when seeing any failure.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Linus Torvalds