The pseries PCI hotplug code cannot build as a module, unless
the pcibios_remove_pci_devices function is exported.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/pci_dlpar.c | 1 +
1 file changed, 1 insertion(+)
Signed-off-by: Paul Mackerras <paulus@samba.org>
I have never seen a use of SLAB_DEBUG_INITIAL. It is only supported by
SLAB.
I think its purpose was to have a callback after an object has been freed
to verify that the state is the constructor state again? The callback is
performed before each freeing of an object.
I would think that it is much easier to check the object state manually
before the free. That also places the check near the code object
manipulation of the object.
Also the SLAB_DEBUG_INITIAL callback is only performed if the kernel was
compiled with SLAB debugging on. If there would be code in a constructor
handling SLAB_DEBUG_INITIAL then it would have to be conditional on
SLAB_DEBUG otherwise it would just be dead code. But there is no such code
in the kernel. I think SLUB_DEBUG_INITIAL is too problematic to make real
use of, difficult to understand and there are easier ways to accomplish the
same effect (i.e. add debug code before kfree).
There is a related flag SLAB_CTOR_VERIFY that is frequently checked to be
clear in fs inode caches. Remove the pointless checks (they would even be
pointless without removeal of SLAB_DEBUG_INITIAL) from the fs constructors.
This is the last slab flag that SLUB did not support. Remove the check for
unimplemented flags from SLUB.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement deep-sleep on MPC52xx.
SDRAM is put into self-refresh with help of SRAM code
(alternatives would be code in FLASH, I-cache).
Interrupt code must also not be in SDRAM, so put it
in I-cache.
MPC52xx core is static, so contents will remain intact even
with clocks turned off.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC.
Tested to work with built-in eeprom on lite5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the global cpu speed variable according to current cpufreq speed,
/proc/cpuinfo reports the actual speed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows "hotplugging" of CPUs on G5 machines. CPUs that are
disabled are put into an idle loop with the decrementer frequency set
to minimum. To wake them up again we kick them just like when bringing
them up. To stop those CPUs from messing with any global state we stop
them from entering the timer interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
remove "struct subsystem" as it is no longer needed
sysfs: printk format warning
DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
platform: reorder platform_device_del
Driver core: fix show_uevent from taking up way too much stack
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
PCI: Free resource files in error path of pci_create_sysfs_dev_files()
pci-quirks: disable MSI on RS400-200 and RS480
PCI hotplug: Use menuconfig objects
PCI: ZT5550 CPCI Hotplug driver fix
PCI: rpaphp: Remove semaphores
PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
PCI: rpaphp: Document is_php_dn()
PCI: rpaphp: Document find_php_slot()
PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
PCI: rpaphp: refactor tail call to rpaphp_register_slot()
PCI: rpaphp: remove rpaphp_set_attention_status()
PCI: rpaphp: remove print_slot_pci_funcs()
PCI: rpaphp: Remove setup_pci_slot()
PCI: rpaphp: remove a call that does nothing but a pointer lookup
PCI: rpaphp: Remove another wrappered function
PCI: rpaphp: Remve another call that is a wrapper
PCI: rpaphp: remove a function that does nothing but wrap debug printks
PCI: rpaphp: Remove un-needed goto
PCI: rpaphp: Fix a memleak; slot->location string was never freed
...
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only publish of_platform devices if running on a machine that has them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixups for the ps3 interrupt routines to support all HV device
in a generic way.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A minor change to remove a duplicate variable assignement in ps3_mm_shutdown();
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 support for the PowerPC processor's Data Address Breakpoint Register
(DABR).
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 0fba3a1f39 (a very long time ago,
May 2006), I fixed a bug that caused powermacs to crash when you tried
entering standby/mem suspend states.
As I'm now getting more familiar with the suspend code I notice a few
more things:
1. we previously misunderstood what pm_ops is for, it isn't supposed to be
for doing platform dependent suspend/resume stuff that needs to be done
for suspend to disk (as we currently try to use it!), it is instead for
entering platform dependent suspend states ("standby", "mem").
2. due to the first point, we never properly save FPU and altivec states
when suspending to disk. It probably hasn't hurt yet because the process
that writes the "disk" to /sys/power/state uses neither and its context
is used.
This patch addresses these points as follows:
1. remove all pm_ops from powermac, powermac suspend to ram isn't currently
usable via /sys/power/state but is done via the PMU instead.
2. move the code responsible for storing FPU/altivec state into
save_processor_state and the set_context() call to restore_processor_state.
3. add a call to kernel_enable_spe()
It may look like there is some code removal missing but that is
actually because the new suspend.h file overrides the ppc/suspend.h
one which was previously used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't have it active by default, the STRICT_MM_TYPECHECKS
option has bitrotted again. This patch fixes a couple of simple build
fixes if the option is selected. First, pud_t mustn't be defined in
page.h on 32-bit systems, because it conflicts with the version in the
generic pud-folding code. Second, pci_32.c is missing a __pgprot()
wrapper call. Third, a couple of PS3 files use constants of type
pgprot_t when they need the raw values, we add pgprot_val() calls to
fix this.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add 'mdio' to bus scan id list for platforms with QE UEC
as a consequence of converting UEC mdio driver to an
of_platform driver in the ucc_geth phylib conversion patch.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some versions of pSeries firmware fail to set up a
dma-window property for PCI slots that are unoccupied.
As a result, the loop searching for this propery, in
pci_dma_dev_setup_pSeriesLP(), can run to the end, resulting
in a NULL pointer dereference later in the routine. This
patch prevents the crash, and prints a warning message.
This is theoretically a rare error, as it occurs on what
is hopefully just beta levels of firmware. But just in case
this firmware escapes into the wild, this patch will avoid
the crash.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
The original code here is wrong, it applies "previous" knowledge.
The way the cpufreq core is designed is that the policy for the
secondary CPU that comes online says that it must in fact not
use this policy but use the same as the other CPUs that are
listed, which in fact is CPU#0.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove loops_per_jiffy early initialization code for 7448HPC2 platforms.
Since udelay no longer uses loops_per_jiffy it is not necessary to
initialize it early.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call of_find_node_by_type with NULL instead of np
so the cpu node does not get put twice.
This was causing kref_put warnings.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use DEFINE_SPINLOCK instead of initializing spinlocks to
SPIN_LOCK_UNLOCKED, since DEFINE_SPINLOCK is better for lockdep.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just another pass through arch/powerpc for old usages.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Shuffle Kconfig order, making the platform drivers menu depend on the global
option instead of each driver being dependent on it.
Also fix dependency of PPC_PMAC on the G5 one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 9414715a7b,
at Olaf Hering's request:
> Paul, please discard this patch. The optional graphics card may have
> also device_type 'serial' if it is in VGA mode.
> I will send an updated patch later.
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cpufreq driver for PA Semi PWRficient processors.
Signed-off-by: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/gpio_mdio.c really depends on CONFIG_PHYLIB.
Add a config option for it, allow for it to be disabled if needed and fix
the dependency.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/setup.c: In function 'pasemi_publish_devices':
arch/powerpc/platforms/pasemi/setup.c:220: warning: implicit declaration of function 'of_platform_bus_probe'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is an old interface and is replaced by of_find_compatible_node.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename MPIC_BROKEN_U3 to something a little more descriptive. Its
effect is to enable support for HT irqs behind the PCI-X/HT bridge on
U3/U4 (aka. CPC9x5) parts.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we always take a device tree in arch/powerpc, there's no good
reason not to allow a single kernel to support multiple embedded 4xx
boards - the correct platform code can be selected based on the device
tree information.
Therefore, this patch re-arranges the 4xx Kconfig code to allow this.
In addition we:
- use "select" instead of depends to configure the correct
config options for specific 4xx CPUs and workarounds, which
makes the information about specific boards and CPUs less
scattered.
- Some old, unused (in arch/powerpc) config options are
removed: WANT_EARLY_SERIAL, IBM_OCP, etc.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MDIO driver for PHY's connected via GPIO as on the PA Semi Electra
eval board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reset MPIC on boot to clear some timer state that firmware might
leave configured.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device 0 function 0 on the root bus is really a two-function bus agent,
but only the first function is visible. Because of this, we need to
allow config accesses into the second range. Modify the check for valid
offsets accordingly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable Periodic Recalibration (PTCAL) support for Cell XDR memory,
using the new ibm,cbe-start-ptcal and ibm,cbe-stop-ptcal RTAS calls.
Tested on QS20 and QS21 (by Thomas Huth). It seems that SLOF has
problems disabling, at least on QS20; this patch should only be
used once these problems have been addressed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for a proper device-tree.
A porper device-tree on cell contains be nodes
for each CBE containg nodes for SPEs and all the
other special devices on it.
Ofcourse oldschool devicetree is still supported.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The new PMI driver was added in order to support
cpufreq on blades that require the frequency to
be controlled by the service processor, so use it
on those.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds some attributes the cpu and spu nodes:
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_begin
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_end
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_full_stop
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch introduces a little function for transforming
register values into temperature.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This change fixes the case where spu_base and spufs are initialised on a
system with no SPEs - unconditionally create the spu_lists so spu_alloc
doesn't explode, and check for spu_management ops before starting spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
arch/powerpc/platforms/cell/spu_base.c | 7 ++++---
arch/powerpc/platforms/cell/spufs/inode.c | 5 +++++
2 files changed, 9 insertions(+), 3 deletions(-)
spu_base.c is always built into the kernel image, so there is no need
for a cleanup function. And some of the things it does are in the
way for my following patches, so I'd rather get rid of it ASAP.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
- remove the spu_acquire_runnable from spu_run_init. I need to
opencode it in spufs_run_spu in the next patch
- remove various inline attributes, we don't really want to inline
long functions with multiple callsites
- cleanup return values and runcntl_write calls in spu_run_init
- use normal kernel codingstyle in spu_reacquire_runnable
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spu_coredump_calls.owner is NULL in case of a builtin spufs,
so the checks in here break.
Check for the availability of the spu_coredump_calls variable
instead.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Dynamically allocated read/write buffer in spufs_arch_write_note() will
not be freed. Convert it to get_free_page at the same time.
Cc: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Change the loop in spu_wait to be a little more straightforward.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Add a 'mode=' option to spufs mount arguments. This allows more
control over access to the top-level spufs directory.
Tested on Cell.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
GCC may generates inline copy loop to handle memcpy() function
instead of kernel defined memcpy(). But this inlined version of memcpy()
causes an alignment interrupt when copying from local store.
This patch uses memcpy_fromio() and memcpy_toio to copy local store
to prevent memcpy() being inlined.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
We now have proper locking around assignets of the mapping pointers,
and the spin_unlock implies enough of a barrier to get rid of the
explicit one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
When SPU isolation mode enabled, isolated_loader would be
allocated by spufs_init_isolated_loader() on module_init().
But anyone do not free it.
This patch introduces spufs_exit_isolated_loader() which is
the opposite of spufs_init_isolated_loader() and called on
module_exit().
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spufs module_init forgot to call a few cleanup functions
on error path. This patch also includes cosmetic changes in
spu_sched_init() (identation fix and return error code).
[modified by hch to apply ontop of the latest schedule changes]
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch checks return value of spu_acquire_runnable() in
spufs_mfc_write().
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
There is no reason for run_sema to be a struct semaphore. Changing
it to a mutex and rename it accordingly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This change populates a siginfo struct for SPE application exceptions
(ie, invalid DMAs and illegal instructions).
Tested on an IBM Cell Blade.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
page faults
- if an spu program attempts to access its own mmio
areas through DMA, we get an immediate livelock when
the nopage function tries to acquire the same mutex
This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.
We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
There is no reason to execute spu_init_channels under spu_mutex
after the spu has been taken off the freelist it's ours.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Addition to stop_wq needs to happen before adding to the runqeueue and
under the same lock so that we don't have a race window for a lost
wake up in the spu scheduler.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
For quite a while now spu state is protected by a simple mutex instead
of the old rw_semaphore, and this means we can simplify the locking
around spu_setup_isolated a lot.
Instead of doing an spu_release before entering spu_setup_isolated and
then calling the complicated spu_acquire_exclusive we can now simply
enter the function locked an in guaranteed runnable state, so that the
only bit of spu_acquire_exclusive that's left is the call to
spu_unmap_mappings.
Similarly there's no more need to unlock and reacquire the state_mutex
when spu_setup_isolated is done, but we can always return with the
lock held and only drop it in spu_run_init in the failure case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
A single context should only be woken once, and we should not have
more wakeups for a given priority than the number of contexts on
that runqueue position.
Also add some asserts to trap future problems in this area more
easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
set_bit does not guarantee ordering on powerpc, so using it
for communication between threads requires explicit
mb() calls.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
To not lose a spu thread we need to make sure it always gets put back
on the runqueue. In find_victim aswell as in the scheduler tick as done
in the previous patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
To not lose a spu thread we need to make sure it always gets put back
on the runqueue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Make sure the pointers to various mappings are cleared once the last
user stopped using them. This avoids accessing freed memory when
tearing down the gang directory aswell as optimizing away
pte invalidations if no one uses these.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The scheduler workqueue may rearm itself and deadlock when we try to stop
it. Put a flag in place to avoid skip the work if we're tearing down
the context.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
* Cleaned up some whitespace in arch/powerpc/Kconfig
* Moved sourcing of platforms/embedded6xx/Kconfig into platform/Kconfig
* Moved sourcing of platforms/4xx/Kconfig into platform/Kconfig and disabled it
* Removed EMBEDDEDBOOT since its not supported in arch/powerpc
* Removed PC_KEYBOARD since its not used anywhere
* Moved a few CONFIG options around in platform/Kconfig
* Moved interrupt controllers into platform/Kconfig out of bus section
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved 8xx platform Kconfig over to being sourced by the unified
arch/powerpc/platforms/Kconfig. Also, cleaned up whitespace issues in 8xx
Kconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved 82xx platform Kconfig over to being sourced by the unified
arch/powerpc/platforms/Kconfig. Also, cleaned up whitespace issues in 82xx
Kconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This also fixes a bug where a property value was being modified
in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Efika boards have to be booted with console=ttyPSC0 unless there is a
graphics card plugged in. Detect if the firmware stdout is the serial
connector.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no reason to yield the CPU in spu_yield - if the backing
thread reenters spu_run it gets added to the end of the runqueue for
it's priority. So the yield is just a slowdown for the case where
we have higher priority contexts waiting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I wanted to enable CBE_THERM on PS3. So I had to enable CBE_RAS first.
But the resulting kernel doesn't link, as cbe_regs.c isn't compiled for
non-PPC_CELL_NATIVE.
CBE_RAS should depend on PPC_CELL_NATIVE; this makes it so.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove unneeded inclusion of linux/ide.h
It does not compile with CONFIG_BLOCK=n.
Remove asm/ide.h from ksyms file, it gets included earlier via
linux/ide.h.
Compile tested with all defconfig files.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix link errors with CONFIG_EEH=n:
arch/powerpc/platforms/built-in.o: In function `.pcibios_fixup_new_pci_devices':
(.text+0x41c8): undefined reference to `.eeh_add_device_tree_late'
arch/powerpc/platforms/built-in.o: In function `.init_phb_dynamic':
(.text+0x4280): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pcibios_remove_pci_devices':
(.text+0x42fc): undefined reference to `.eeh_remove_bus_device'
arch/powerpc/platforms/built-in.o: In function `.pcibios_add_pci_devices':
(.text+0x43c0): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pSeries_final_fixup':
(.init.text+0xb4): undefined reference to `.pci_addr_cache_build'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bit setting was off by one.
Tested with RTC and GPIO_WKUP interrupts.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8323E Reference Development Board (RDB). The board
is a mini-ITX reference board with 64M DDR2, 16M flash, USB, PCI,
10/100 ethernet, serial, and phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc832x_mds.h was exporting a function that didn't exist anymore. Once removed
the header had no purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Delete apparently unused header file
arch/powerpc/platforms/83xx/mpc834x_itx.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected. Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled. A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This move sets the stage for the use of generic PCI Express
code in 85xx and 86xx parts from FSL. Subsequent patches
for 8548 and 8544 will be able to use this shared code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linas Vepstas