Pull followup block layer updates from Jens Axboe:
"I ended up splitting the main pull request for this series into two,
mainly because of clashes between NVMe fixes that went into 4.13 after
the for-4.14 branches were split off. This pull request is mostly
NVMe, but not exclusively. In detail, it contains:
- Two pull request for NVMe changes from Christoph. Nothing new on
the feature front, basically just fixes all over the map for the
core bits, transport, rdma, etc.
- Series from Bart, cleaning up various bits in the BFQ scheduler.
- Series of bcache fixes, which has been lingering for a release or
two. Coly sent this in, but patches from various people in this
area.
- Set of patches for BFQ from Paolo himself, updating both
documentation and fixing some corner cases in performance.
- Series from Omar, attempting to now get the 4k loop support
correct. Our confidence level is higher this time.
- Series from Shaohua for loop as well, improving O_DIRECT
performance and fixing a use-after-free"
* 'for-4.14/block-postmerge' of git://git.kernel.dk/linux-block: (74 commits)
bcache: initialize dirty stripes in flash_dev_run()
loop: set physical block size to logical block size
bcache: fix bch_hprint crash and improve output
bcache: Update continue_at() documentation
bcache: silence static checker warning
bcache: fix for gc and write-back race
bcache: increase the number of open buckets
bcache: Correct return value for sysfs attach errors
bcache: correct cache_dirty_target in __update_writeback_rate()
bcache: gc does not work when triggering by manual command
bcache: Don't reinvent the wheel but use existing llist API
bcache: do not subtract sectors_to_gc for bypassed IO
bcache: fix sequential large write IO bypass
bcache: Fix leak of bdev reference
block/loop: remove unused field
block/loop: fix use after free
bfq: Use icq_to_bic() consistently
bfq: Suppress compiler warnings about comparisons
bfq: Check kstrtoul() return value
bfq: Declare local functions static
...
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----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=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
And fix the Get/Set Log Page implementation to take all 8 bits of the
feature identifier into account.
Signed-off-by: Omri Mann <omri@excelero.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[hch: used the UUID API, updated changelog]
This changes the earlier patch "nvmet: don't report 0-bytes
in serial number" to use the memcpy_and_pad() helper introduced
in a previous patch.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The existing nvmet_fc sg list handling has 2 faults:
a) the request between LLDD and transport has too large of an sg
list (256 elements), which is normally 256k (64 elements).
b) sglist handling doesn't optimize on the fact that each element
is a page.
This patch removes the static sg list in the request and uses the
dynamic list already present in the nvmet_fc transport. It also
simplies the handling of the sg list on multiple sequences to
take advantage of the per-page divisions.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvmf target shall return NVME_SC_CONNECT_INVALID_HOST instead of
the gereal code INVALID_PARAM when the given host nqn is not allowed
to connect. Refer to the 2.2.1 section of the NVMe over Fabrics Spec.
Signed-off-by: Guan Junxiong <guanjunxiong@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that its not needed, we can simply not assign it.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There were 2 statics introduced that were bogus. Removed the static
designations.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use list_for_each_entry_safe to prevent list handling from referencing
next pointers directly after list_del's
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The merged version of my patch "nvmet: don't report 0-bytes in serial
number" fails to remove two lines which should have been replaced,
so that the space-padded strings are overwritten again with 0-bytes.
Fix it.
Fixes: 42de82a8b5 nvmet: don't report 0-bytes in serial number
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
At queue creation, the transport allocates a local job struct
(struct nvmet_fc_fcp_iod) for each possible element of the queue.
When a new CMD is received from the wire, a jobs struct is allocated
from the queue and then used for the duration of the command.
The job struct contains buffer space for the wire command iu. Thus,
upon allocation of the job struct, the cmd iu buffer is copied to
the job struct and the LLDD may immediately free/reuse the CMD IU
buffer passed in the call.
However, in some circumstances, due to the packetized nature of FC
and the api of the FC LLDD which may issue a hw command to send the
wire response, but the LLDD may not get the hw completion for the
command and upcall the nvmet_fc layer before a new command may be
asynchronously received on the wire. In other words, its possible
for the initiator to get the response from the wire, thus believe a
command slot free, and send a new command iu. The new command iu
may be received by the LLDD and passed to the transport before the
LLDD had serviced the hw completion and made the teardown calls for
the original job struct. As such, there is no available job struct
available for the new io. E.g. it appears like the host sent more
queue elements than the queue size. It didn't based on it's
understanding.
Rather than treat this as a hard connection failure queue the new
request until the job struct does free up. As the buffer isn't
copied as there's no job struct, a special return value must be
returned to the LLDD to signify to hold off on recycling the cmd
iu buffer. And later, when a job struct is allocated and the
buffer copied, a new LLDD callback is introduced to notify the
LLDD and allow it to recycle it's command iu buffer.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The FC-NVME spec hasn't locked down on the format string for TRADDR.
Currently the spec is lobbying for "nn-<16hexdigits>:pn-<16hexdigits>"
where the wwn's are hex values but not prefixed by 0x.
Most implementations so far expect a string format of
"nn-0x<16hexdigits>:pn-0x<16hexdigits>" to be used. The transport
uses the match_u64 parser which requires a leading 0x prefix to set
the base properly. If it's not there, a match will either fail or return
a base 10 value.
The resolution in T11 is pushing out. Therefore, to fix things now and
to cover any eventuality and any implementations already in the field,
this patch adds support for both formats.
The change consists of replacing the token matching routine with a
routine that validates the fixed string format, and then builds
a local copy of the hex name with a 0x prefix before calling
the system parser.
Note: the same parser routine exists in both the initiator and target
transports. Given this is about the only "shared" item, we chose to
replicate rather than create an interdendency on some shared code.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The NVME standard mandates that the SN, MN, and FR fields of the Identify
Controller Data Structure be "ASCII strings". That means that they may
not contain 0-bytes, not even string terminators.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
[hch: fixed for the move of the serial field, updated description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe target has no way to preserve controller serial
IDs across reboots which breaks udev scripts doing
SYMLINK+="dev/disk/by-id/nvme-$env{ID_SERIAL}-part%n.
Export the randomly generated serial number via configfs and allow
setting of a serial via configfs to mitigate this breakage.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe specification defines the serial number as:
"Serial Number (SN): Contains the serial number for the NVM subsystem
that is assigned by the vendor as an ASCII string. Refer to section
7.10 for unique identifier requirements. Refer to section 1.5 for ASCII
string requirements"
So move it from the controller to the subsystem, where it belongs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe target's attribute files need an attr prefix in order to have
nvmetcli recognize them. Add this attribute.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We always need to do non-equal comparisms on the native endian versions
to get the correct result.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We actually using the cookie returned from the last submit_bio
call.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Target validation of the Create Association LS revised to accept any
LS as long as all non-pad data has been received. This allows a (newer)
target to accept the LS from older initiators with varying pad lengths.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Usually before we teardown the controller we want to:
1. complete/cancel any ctrl inflight works
2. remove ctrl namespaces (only for removal though, resets
shouldn't remove any namespaces).
but we do not want to destroy the controller device as
we might use it for logging during the teardown stage.
This patch adds nvme_start_ctrl() which queues inflight
controller works (aen, ns scan, queue start and keep-alive
if kato is set) and nvme_stop_ctrl() which cancels the works
namespace removal is left to the callers to handle.
Move nvme_uninit_ctrl after we are done with the
controller device.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
unlike blk_mq_stop_hw_queues and blk_mq_start_stopped_hw_queues
quiescing/unquiescing respects the submission path rcu grace.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
We might have more/less queues once we reconnect/reset. For
example due to cpu going online/offline
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
All transports use either a private cache of controller cap or an on-stack
copy, move it to the generic struct nvme_ctrl. In the future it will also
be maintained by the core.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
All all transports use the queue_count in exactly the same, so move it to
the generic struct nvme_ctrl. In the future it will also be maintained by
the core.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-By: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
We can deadlock in case we got to a device removal
event on a queue which is already in the process of
destroying the cm_id is this is blocking until all
events on this cm_id will drain. On the other hand
we cannot guarantee that rdma_destroy_id was invoked
as we only have indication that the queue disconnect
flow has been queued (the queue state is updated before
the realease work has been queued).
So, we leave all the queue removal to a separate ib_client
to avoid this deadlock as ib_client device removal is in
a different context than the cm_id itself.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
if a nvme command is issued with an opcode that is not supported by
the target (example: opcode 21 - detach namespace), the target
crashes due to a null pointer.
nvmet_req_init() detects the bad opcode and immediately calls the nvme
command done routine with an error status, allowing the transport to
send the response. However, the FC transport was aborting the command
on error, so the abort freed the lldd point, but the rsp transmit path
referenced it psot the free.
Fix by removing the abort call on nvmet_req_init() failure.
The completion response will be sent with an error status code.
As the completion path will terminate the io, ensure the data_sg
lists show an unused state so that teardown paths are successful.
Signed-off-by: Paul Ely <Paul.Ely@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NVMe 1.2.1 or later requires controllers to provide a subsystem NQN in the
Identify controller data structures. Use this NQN for the subsysnqn
sysfs attribute by storing it in the nvme_ctrl structure after verifying
it. For older controllers we generate a "fake" NQN per non-normative
text in the NVMe 1.3 spec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to differentiate fabrics from pci/loop, also lower
it to 32 as we don't really need 256 inflight admin commands.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This moves the nvme_reset function from the PCIe driver to common code,
renaming it to nvme_reset_ctrl in the process. Additionally a new
helper nvme_reset_ctrl_sync is added for the case where we want to
wait for the reset. To facilitate that the reset_work work structure is
move to the common nvme_ctrl structure and the ->reset_ctrl method is
removed. For now the drivers initialize the reset_work with their own
callback, but longer term we should move to callouts for specific
parts of the reset process and move even more code to the core.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Now that we get the tagset passed we can have a single implementation for
the I/O and admin queues.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This was detected by building the nvmet-fc driver with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Allow overriding the announced NVMe Version of a via configfs.
This is particularly helpful when debugging new features for the host
or target side without bumping the hard coded version (as the target
might not be fully compliant to the announced version yet).
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add the UUID field from the NVMe Namespace Identification Descriptor
to the nvmet_ns structure and allow it's population via configfs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A NVMe Identify NS command with a CNS value of '3' is expecting a list
of Namespace Identification Descriptor structures to be returned to
the host for the namespace requested in the namespace identify
command.
This Namespace Identification Descriptor structure consists of the
type of the namespace identifier, the length of the identifier and the
actual identifier.
Valid types are NGUID and UUID which we have saved in our nvme_ns
structure if they have been configured via configfs. If no value has
been assigened to one of these we return an "invalid opcode" back to
the host to maintain backward compatibiliy with older implementations
without Namespace Identify Descriptor list support.
Also as the Namespace Identify Descriptor list is the only mandatory
feature change between 1.2.1 and 1.3 we can bump the advertised
version as well.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use NVME_IDENTIFY_DATA_SIZE define instead of hard coding the magic
4096 value.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
[hch: converted three more users]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of each transport using it's own workqueue, export
a single nvme-core workqueue and use that instead.
In the future, this will help us moving towards some unification
if controller setup/teardown flows.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use the same values for use for request completion errors as the return
value from ->queue_rq. BLK_STS_RESOURCE is special cased to cause
a requeue, and all the others are completed as-is.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
So that we can have more flags for transport-specific behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
On rdma read errors, release the sq ref that was taken
when the req was initialized. This avoids a hang in
nvmet_sq_destroy() when the queue is being freed.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds