The BCM28155-AP board has a bootloader that expects the camldo1
regulator to be enabled on entry. Currently, the camldo1 regulator
is disabled when no longer in use as is the case during a reboot /
warm reset. This causes the early bootloader to hang upon entry. Add
regulator-always-on to the camldo1 constraint to fix reboot.
Reported-by: Alex Elder <elder@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>
Add a dtsi to support the BCM590xx PMUs used by the BCM281xx family
of SoCs. Enable regulators for use with the dwc2 and sdhci on
bcm28155-ap.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
The sdio1 interface pins are routed to an unpopulated daughter card
connector on the bcm28155-ap board. Thus there is no need to mark
this interface as enabled.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.
Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Adds USB OTG/PHY and clock support to BCM281xx and enables
UDC support on the bcm11351-brt and bcm28155-ap boards.
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Enable all available i2c busses.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Register GPIO 14 as card detect interrupt for the SD card slot.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Also rename the the following dt binding docs that had "bcm,"
in their name for consistency:
- bcm,kona-sdhci.txt -> kona-sdhci.txt
- bcm,kona-timer.txt -> kona-timer.txt
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Enable sdio for bcm28155 AP board
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Matt Porter