The KSZ9031 appears to suffer from the same hardware bug as described
for the KSZ9021 in commit 32fcafbcd1
("net/phy: micrel: Disable asymmetric pause for KSZ9021")
you have to unplug the cable and plug it back to get it to work.
Remove the SUPPORTED_Asym_Pause flag for the KSZ9031 to fix this.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Std 802.3az if the EEE Adv (Reg 7.60), Link partner ability
(Reg 7.61) and EEE capability (Register 3.20) bits return 0 this means no EEE
is supported. So this patch fixes the checks inside the phy_init_eee function.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the one hand, phy_device.c provides a generic reset function if the phy
driver does not provide a soft_reset pointer. This generic reset does not take
into account the state of the phy, with a potential failure if the phy is in
powerdown mode. On the other hand, smsc driver provides a function with both
correct reset behaviour and configuration.
This patch moves the reset part into a new smsc_phy_reset function and provides
the soft_reset pointer to have a correct reset behaviour by default.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.
Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a71e3c3796 ("net: phy: Set the driver when registering an MDIO bus
device") caused the following regression on the fec driver:
root@imx6qsabresd:~# echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.003 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Unable to handle kernel NULL pointer dereference at virtual address 0000002c
pgd = bcd14000
[0000002c] *pgd=4d9e0831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 617 Comm: sh Not tainted 3.16.0 #17
task: bc0c4e00 ti: bceb6000 task.ti: bceb6000
PC is at fec_suspend+0x10/0x70
LR is at dpm_run_callback.isra.7+0x34/0x6c
pc : [<803f8a98>] lr : [<80361f44>] psr: 600f0013
sp : bceb7d70 ip : bceb7d88 fp : bceb7d84
r10: 8091523c r9 : 00000000 r8 : bd88f478
r7 : 803f8a88 r6 : 81165988 r5 : 00000000 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : bd88f478 r0 : bd88f478
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 4cd1404a DAC: 00000015
Process sh (pid: 617, stack limit = 0xbceb6240)
Stack: (0xbceb7d70 to 0xbceb8000)
....
The problem with the original commit is explained by Russell King:
"It has the effect (as can be seen from the oops) of attaching the MDIO bus
device (itself is a bus-less device) to the platform driver, which means
that if the platform driver supports power management, it will be called
to power manage the MDIO bus device.
Moreover, drivers do not expect to be called for power management
operations for devices which they haven't probed, and certainly not for
devices which aren't part of the same bus that the driver is registered
against."
This reverts commit a71e3c3796.
Cc: <stable@vger.kernel.org> #3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions. Also, a label is removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current time range waiting for Rx/Tx to become ready can sometimes
be too short if a connection is not present. Increase the number of
retries and the sleep to give a bit more time. Also, change level of
the message issued from _err to _dbg if Rx/Tx do not become ready
since the underlying logic will function as if no link is established
and retry eventually.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel ksz9021 PHY does not support standard IEEE standard MMD
extended register access, therefore requires stubs to fail the read
register method and do nothing for the write register method when
libphy attempts to read and/or configure Energy Efficient Ethernet
features in PHYS that do support those features. This problem
was observed on an Altera Cyclone V SOC development kit that
uses the Synopsys EMAC and the Micrel ksz9021 PHY. This patch
was tested on the same board, and Energy Efficient Ethernet is
now disabled as expected since the Micrel PHY does not support that
feature.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libphy was originally written assuming all phy devices support clause 45
access extensions to the mmd registers through the indirection registers
located within the first 16 phy registers. This assumption is not true
in all cases, and one specific example is the Micrel ksz9021 10/100/1000
Mbps phy. Using the stmmac driver, accessing the mmd registers to query
and configure energy efficient Ethernet (EEE) features yielded unexpected
behavior.
This patch adds mmd access functions to the phy driver that can be
overriden by the phy specific driver if the phy does not support this
mechanism or uses it's own non-standard access mechanism. By default,
the IEEE Compatible clause 45 access mechanism described in clause 22
is used. With this patch, EEE query/configure functions as expected
using the stmmac and the Micrel ksz9021 phy.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a netdev_info statement detailing whether auto-negotiation was
completed through parallel detection or through the auto-negotiation
protocol.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of changing rates to KR mode, KR training is initiated. If
the KR training is restarted it is possible to enter an invalid logic
state. This can be avoided by asserting a training reset bit before
initiating the KR training and then clearing the training reset bit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the logic will loop endlessly waiting for a rate change
to complete. Add a counter so that if the rate change signals
never indicate complete the loop will eventually exit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
moved the call to phy_scan_fixups() in phy_init_hw() after a software
reset is performed.
By the time phy_init_hw() is called in phy_device_register(), no driver
has been bound to this PHY yet, so all the checks in phy_init_hw()
against the PHY driver and the PHY driver's config_init function will
return 0. We will therefore never call phy_scan_fixups() as we should.
Fix this by calling phy_scan_fixups() and check for its return value to
restore the intended functionality.
This broke PHY drivers which do register an early PHY fixup callback to
intercept the PHY probing and do things like changing the 32-bits unique
PHY identifier when a pseudo-PHY address has been used, as well as
board-specific PHY fixups that need to be applied during driver probe
time.
Reported-by: Hauke Merthens <hauke-m@hauke-m.de>
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds proper module_{get,put} to prevent the MDIO bus module
from being unloaded while the phydev is connected. By doing so, we fix
a kernel panic produced when a MDIO driver is removed, but the phydev
that relies on it is attached and running.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register() registers a device which is already bound to a driver.
Hence, the driver pointer should be set properly in order to track down
the driver associated to the MDIO bus.
This will be used to allow ethernet driver to pin down a MDIO bus driver,
preventing it from being unloaded while the PHY device is running.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When timestamping received packets, rx_timestamp_work may be scheduled
before the timestamps is received from the hardware resulting in the
packet beeing delivered without the timestamp.
This is fixed by changing the receive timestamp path:
On receiving a packet that need timestamping, the rxts list is
traversed. If a match is found, packet+timestamp are delivered,
otherwise the packet is added to a rx_queue.
When a timestamp arrives rx_queue is traversed and if a matching
packet is found, it is delivered with the timestamp. Otherwise the
timestamp is added to the rxts list for matching with packets arriving
later.
In case the hardware drops a timestamp, a workqueue regularly checks
the queue for old packets and delivers them without a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the phy speed/duplex settings array to support more
than just baseT features. This change adds entries to support
the following additional speed/duplex/media types:
SUPPORTED_10000baseKR_Full
SUPPORTED_10000baseKX4_Full
SUPPORTED_2500baseX_Full
SUPPORTED_1000baseKX_Full
Additionally, it changes the 10GbE baseT entry from using the
hardcoded value 10000 to the SPEED_10000 define.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Event timestamp values should be adjusted by 3*reference clock period +
11 ns = 35 ns to compensate for input path and synchronization delays.
So subtract 35ns from event timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently status frames are only handled when packet timestamping is
enabled, but status frames are also needed for pin event timestamping.
Fix by moving packet timestamping check to after status frame decode.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend and phy_resume are two commonly used helper functions that
need to be exported for Ethernet drivers to be built as modules
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.
depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!
The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.
Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, use the ptp_find_pin function to get the calibration pin,
not gpio_tab.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This constraints the pin assignment to not allow the calibration function to
be reassigned and only allow reassigning the calibratin pin if only one phy is
connected.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the number of supported periodic output pins from
1 to 7. The last pin is reserved for sync.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Periodic output triggers 0 and 1 of the dp83640 has a programmable
duty-cycle which is controlled by the Pulsewidth2 field of the trigger
data register. This field is not documented in the datasheet, but it
is described in the "PHYTER Software Development Guide" section
3.1.4.1. Failing to set the field can result in unstable/no trigger
output.
Add programming of the Pulsewidth2 field, setting it to the same value
as the Pulsewidth field for a 50% duty cycle.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/at803x.c:196:26-32: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using phy_drivers_register/_unregister functions is proper way to
handle multiple PHY drivers registration. For Realtek PHY drivers
module, it fixes incomplete current error-handlings up and adds
missed unregistration for the RTL8201CP driver.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following compilation warning:
[...]
CC drivers/net/phy/amd-xgbe-phy.o
drivers/net/phy/amd-xgbe-phy.c:1353:30: warning:
‘amd_xgbe_phy_ids’ defined but not used [-Wunused-variable]
static struct mdio_device_id amd_xgbe_phy_ids[] = {
^
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the initial phylib driver in support
of the AMD 10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to walk the list of subnodes of a mdio bus and look for
a node that matches the phy's address with its 'reg' property. If found,
set the of_node pointer for the phy. This allows auto-probed pyh
devices to be augmented by information passed in via DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. of_set_phy_supported is
called right after phy_device_register in the assumption that
phy_probe is called from phy_device_register and the features
of the phy are already initialized. For the genphy driver this
is not true, here phy_probe is called later during phy_connect
time. phy_probe will then overwrite all settings done from
of_set_phy_supported
Fix this by moving of_set_phy_supported to the core phy code
and calling it from phy_probe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing fixed_phy_add() function has several drawbacks that
prevents it from being used as is for OF-based declaration of fixed
PHYs:
* The address of the PHY on the fake bus needs to be passed, while a
dynamic allocation is desired.
* Since the phy_device instantiation is post-poned until the next
mdiobus scan, there is no way to associate the fixed PHY with its
OF node, which later prevents of_phy_connect() from finding this
fixed PHY from a given OF node.
To solve this, this commit introduces fixed_phy_register(), which will
allocate an available PHY address, add the PHY using fixed_phy_add()
and instantiate the phy_device structure associated with the provided
OF node.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the fixed_phy_add() function was taking as argument
'phy_id', which was used both as the PHY address on the fake fixed
MDIO bus, and as the PHY id, as available in the MII_PHYSID1 and
MII_PHYSID2 registers. However, those two informations are completely
unrelated.
This patch decouples them. The PHY id of fixed PHYs is hardcoded to be
0x0. Ideally, a really reserved value would be nicer, but there
doesn't seem to be an easy of making sure a dummy value can be
assigned to the Linux kernel for such usage.
The PHY address remains passed by the caller of phy_fixed_add().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), an unused PHY device will be put in a low-power mode
using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start()
and phy_stop() from ndo_open and ndo_close() respectively, while
calling phy_connect() and phy_disconnect() from probe and remove.
In such a case, the PHY will be powered down during the phy_stop()
call, but will fail to be powered up in phy_start().
This patch fixes this scenario.
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called
to detach the phy device from its network device. If the attached driver is a
generic phy driver, this also detaches the driver. Subsequently phy_resume
is called, which assumes without checking that a driver is attached to the
device. This will result in a crash such as
Unable to handle kernel paging request for data at address 0xffffffffffffff90
Faulting instruction address: 0xc0000000003a0e18
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c
LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c
Call Trace:
[c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable)
[c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98
[c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4
Only call phy_resume if phy_init_hw was successful.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6d48f44b7b "mdio_bus: implement devm_mdiobus_alloc/devm_mdiobus_free"
introduced a new function devm_mdiobus_alloc_size() but added an export
for a different function devm_mdiobus_alloc(), which was obviously
a simple mistake that leads to build error whenever this function is
used from a loadable module:
ERROR: "devm_mdiobus_alloc_size" [drivers/net/ethernet/ti/davinci_mdio.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Looijmans