The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- the Realtek RTL8211F PHY needs a 10ms assert delay (the datasheet
mentions: "For a complete PHY reset, this pin must be asserted low
for at least 10ms") and a 30ms deassert delay (the datasheet
mentions: "Wait for a further 30ms (for internal circuits settling
time) before accessing the PHY register". This applies to the
following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95
variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox
A1, GXM Q200, GXM RBox Pro boards.
- the ICPlus IP101GR PHY needs a 10ms assert delay (the datasheet
mentions: "Trst | Reset period | 10ms") and a deassert delay of 10ms
as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms"). This applies to the GXBB
Nexbox A95X board.
- the Micrel KSZ9031 seems to require a 100us delay but use the same
(seemingly safe) values from RTL8211F due to lack of a board to verify
this. This applies to the GXBB P200 board.
The GXBB P201 board is left out from this conversion because it doesn't
have a dedicated PHY node (because it's not clear which PHY is used on
that board).
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently one has to look/calculate the GPIO for the PHY interrupts
manually. Add a comment for the existing PHY interrupt lines to make it
easier to find out which GPIO is used.
This is done using the following calculation:
- number of GPIO AO pins (14 on GXBB: GPIOAO_0..13)
- add the offset of the pin which is used for the interrupt (for example
GPIOZ_15 = 15 on Odroid-C2)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-By: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the external PHY interrupt on the nanopi-k2, odroid-c2, p200, p230
and q200
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGMII ethernet
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the 5 buttons connected to a resistor laddered matrix and sampled
by the SAR ADC channel 0.
Only the p200 board has these buttons, the P201 doesn't.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for i2c bus on gxbb based platforms.
On the OdroidC2 (I2C A) and P200 (I2C B), the pull-up resistor are
present directly on the board. This indicates that these pins are
dedicated to i2c.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add minimal DT files for the Amlogic P20x development boards, based on
the Amlogic S905/GXBB SoC.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Martin Blumenstingl