The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.
This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.
Signed-off-by: Valentin Longchamp<valentin.longchamp@epfl.ch>
Tested-by: Philippe Rétornaz<philippe.retornaz@epfl.ch>
Acked-by: Wolfram Sang<w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arnd noted:
After the "retry_open:" label, we first get the tty_mutex
and then the BKL. However a the end of tty_open, we jump
back to retry_open with the BKL still held. If we run into
this case, the tty_open function will be left with the BKL
still held.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad7877 - keep dma rx buffers in seperate cache lines
Input: psmouse - reset all types of mice before reconnecting
Input: elantech - use all 3 bytes when checking version
Input: iforce - fix Guillemot Jet Leader 3D entry
Input: iforce - add Guillemot Jet Leader Force Feedback
In certain circumstances, especially under heavy load, the AUXADC
completion interrupt may be detected after we've timed out waiting for
it. That conversion would still succeed but the next conversion will
see the completion that was signalled by the interrupt for the previous
conversion and therefore not wait for the AUXADC conversion to run,
causing it to report failure.
Provide a simple, non-invasive cleanup by using try_wait_for_completion()
to ensure that the completion is not signalled before we wait. Since
the AUXADC is run within a mutex we know there can only have been at
most one AUXADC interrupt outstanding. A more involved change should
follow for the next merge window.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With dma based spi transmission, data corruption is observed
occasionally. With dma buffers located right next to msg and
xfer fields, cache lines correctly flushed in preparation for
dma usage may be polluted again when writing to fields in the
same cache line.
Make sure cache fields used with dma do not share cache lines
with fields changed during dma handling. As both fields are part
of a struct that is allocated via kzalloc, thus cache aligned,
moving the fields to the 1st position and insert padding for
alignment does the job.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oliver Schneidewind <osw@emlix.com>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
[dtor@mail.ru - changed to use ___cacheline_aligned as suggested
by akpm]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics hardware requires resetting device after suspend to ram
in order for the device to be operational. The reset lives in
synaptics-specific reconnect handler, but it is not being invoked
if synaptics support is disabled and the device is handled as a
standard PS/2 device (bare or IntelliMouse protocol).
Let's add reset into generic reconnect handler as well.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently all 3 bytes returned by ETP_FW_VERSION_QUERY are significant
and should be taken into account when matching hardware version/features.
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] correct address of _stext with CONFIG_SHARED_KERNEL=y
[S390] ptrace: fix return value of do_syscall_trace_enter()
[S390] dasd: fix race between tasklet and dasd_sleep_on
This reverts commit 977d17bb17, because it
can cause problems with some devices not getting any resources at all
when the resource tree is re-allocated.
For an example of this, see
https://bugzilla.kernel.org/show_bug.cgi?id=15960
(originally https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4982)
(lkml thread: http://lkml.org/lkml/2010/4/19/20)
where Peter Henriksson reported his Xonar DX sound card gone, because
the IO port region was no longer allocated.
Reported-bisected-and-tested-by: Peter Henriksson <peter.henriksson@gmail.com>
Requested-by: Andrew Morton <akpm@linux-foundation.org>
Requested-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to memory-barriers.txt, an smp memory barrier in guest
should always be paired with an smp memory barrier in host,
and I quote "a lack of appropriate pairing is almost certainly an
error". In case of vhost, failure to flush out used index
update before looking at the interrupt disable flag
could result in missed interrupts, resulting in
networking hang under stress.
This might happen when flags read bypasses used index write.
So we see interrupts disabled and do not interrupt, at the
same time guest writes flags value to enable interrupt,
reads an old used index value, thinks that
used ring is empty and waits for interrupt.
Note: the barrier we pair with here is in
drivers/virtio/virtio_ring.c, function
vring_enable_cb.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
The various dasd_sleep_on functions use a global wait queue when
waiting for a cqr. The wait condition checks the status and devlist
fields of the cqr to determine if it is safe to continue. This
evaluation may return true, although the tasklet has not finished
processing of the cqr and the callback function has not been called
yet. When the callback is finally called, the data in the cqr may
already be invalid. The sleep_on wait condition needs a safe way to
determine if the tasklet has finished processing. Use the
callback_data field of the cqr to store a token, which is set by
the callback function itself.
Cc: <stable@kernel.org>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
i915_error_object_create() is called from the timer interrupt and hence
can corrupt the KM_USER0 slot. Use KM_IRQ0 instead.
Reported-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Tested-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The work queue has to be flushed after the device has been made
inaccessible. The patch closes a window during which a work queue might
remain active after the device is removed and would then lead to ACPI
calls with undefined behavior.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Herrmann <morpheus.ibis@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current allocation does not include the memory required for blanking
lines. So avoid memory corruption when multiple devices are using the DMA
memory near each other.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In debugfs, printing of command response reports resp[2] twice: fix it to
resp[3].
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable data error interrupts while we are actually recording that there
is not such errors. This will prevent, in some cases, the warning message
printed at new request queuing (in atmci_start_request()).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The removing of an SD card in certain circumstances can lead to a kernel
oops if we do not make sure that the "data" field of the host structure is
valid. This patch adds a test in atmci_dma_cleanup() function and also
calls atmci_stop_dma() before throwing away the reference to data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two parameters were swapped in the calls to atmci_init_slot().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Anders Grahn <anders.grahn@hd-wireless.se>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SIO chip contains 16 possible gpio lines, not 14. The schematic was
not read carefully.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix FDDI and TR config checks in ipv4 arp and LLC.
IPv4: unresolved multicast route cleanup
mac80211: remove association work when processing deauth request
ar9170: wait for asynchronous firmware loading
ipv4: udp: fix short packet and bad checksum logging
phy: Fix initialization in micrel driver.
sctp: Fix a race between ICMP protocol unreachable and connect()
veth: Dont kfree_skb() after dev_forward_skb()
IPv6: fix IPV6_RECVERR handling of locally-generated errors
net/gianfar: drop recycled skbs on MTU change
iwlwifi: work around passive scan issue
Duplicate entries ended up acpisleep_dmi_table[] by accident.
They don't hurt functionality, but they are ugly, so let's get
rid of them.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code will not remove the sysfs files for fan numbers three
and up. Also, upon exit, fans one and two are removed regardless of
their existence. This patch cleans up the sysfs error handling for
the fans.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* Allow fan minimum RPM to be set to zero without triggering alarms.
* Fix voltage scaling arithmetic and correct scale factors.
* Correct fan1-fan4 alarm bit shifts.
* Correct register address for temp3_smoothing_enable.
* Read the alarm registers with high priority.
Signed-off-by: Ken Milmore <ken.milmore@googlemail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
USB ID entry for "Guillemot Jet Leader 3D" in iforce-main.c did not match
one used in iforce-usb.c
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit b4fe945405 introduced 3 bugs,
fix them:
* Use the right command dword for second packet offset in
RADEON_CNTL_PAINT/BITBLT_MULTI.
* Don't leak memory if drm_buffer_copy_from_user() fails.
* Don't call drm_buffer_unprocessed() unless drm_buffer_alloc() and
drm_buffer_copy_from_user() have been called successfully first.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit 672917dcc7 ("cpuidle: menu governor: reduce latency on exit")
added an optimization, where the analysis on the past idle period moved
from the end of idle, to the beginning of the new idle.
Unfortunately, this optimization had a bug where it zeroed one key
variable for new use, that is needed for the analysis. The fix is
simple, zero the variable after doing the work from the previous idle.
During the audit of the code that found this issue, another issue was
also found; the ->measured_us data structure member is never set, a
local variable is always used instead.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Corrado Zoccolo <czoccolo@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although the usbhid driver allocates its usbhid structure in the probe
routine, several critical fields in that structure don't get
initialized until usbhid_start(). However if report descriptor
parsing fails then usbhid_start() is never called. This leads to
problems during system suspend -- the system will freeze.
This patch (as1378) fixes the bug by moving the initialization
statements up into usbhid_probe().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-By: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://neil.brown.name/md:
md: restore ability of spare drives to spin down.
md/raid6: Fix raid-6 read-error correction in degraded state
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: fix compilation after 16bit state locking changes
pcmcia: order userspace suspend and resume requests
pcmcia: avoid pccard_validate_cis failure in resume callpath
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
blk-cgroup: Fix an RCU warning in blkiocg_create()
blk-cgroup: Fix RCU correctness warning in cfq_init_queue()
drbd: don't expose failed local READ to upper layers
Move initialization of the virtio framework before the initialization of
mtd, so that block2mtd can be used on virtio-based block devices.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15644
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: sleep: init_set_sci_en_on_resume for Dell Studio 155x
ACPI: fix acpi_hest_firmware_first_pci() caused oops
sbshc: acpi_device_class "smbus_host_controller" too long
power_meter: acpi_device_class "power_meter_resource" too long
acpi_pad: "processor_aggregator" name too long
PNP: don't check for conflicts with bridge windows
ACPI: DMI init_set_sci_en_on_resume for multiple Lenovo ThinkPads
PNPACPI: compute Address Space length rather than using _LEN
ACPI: silence kmemcheck false positive
* 'v4l_for_2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: pxa_camera: move fifo reset direct before dma start
V4L/DVB: video: testing unsigned for less than 0
V4L/DVB: mx1-camera: compile fix
V4L/DVB: budget: Oops: "BUG: unable to handle kernel NULL pointer dereference"
V4L/DVB: ngene: Workaround for stuck DiSEqC pin
V4L/DVB: saa7146: fix regression of the av7110/budget-av driver
V4L/DVB: v4l: fix config dependencies: mxb and saa7191 are V4L2 drivers, not V4L1
V4L/DVB: feature-removal: announce videotext.h removal
V4L/DVB: V4L - vpfe capture - fix for kernel crash
V4L/DVB: gspca: make usb id 0461:0815 get handled by the right driver
V4L/DVB: gspca - stv06xx: Remove the 046d:08da from the stv06xx driver
V4L/DVB: gspca - sn9c20x: Correct onstack wait_queue_head declaration
V4L/DVB: saa7146: fix up bytesperline if it is an impossible value
V4L/DVB: V4L: vpfe_capture - free ccdc_lock when memory allocation fails
V4L/DVB: V4L - Makfile:Removed duplicate entry of davinci
V4L/DVB: omap24xxcam: potential buffer overflow
This patch fixes a regression introduced by the following patch:
"ar9170: load firmware asynchronously"
When we kick off a firmware loading request and then unbind,
or disconnect the usb device right away, we get into trouble:
> ------------[ cut here ]------------
> WARNING: at lib/kref.c:44 kref_get+0x1c/0x20()
> Hardware name: 18666GU
> Modules linked in: ar9170usb [...]
> Pid: 6588, comm: firmware/ar9170 Not tainted 2.6.34-rc5-wl #43
> Call Trace:
> [<c102b05e>] ? warn_slowpath_common+0x6e/0xb0
> [<c117c93c>] ? kref_get+0x1c/0x20
> [<c102b0b3>] ? warn_slowpath_null+0x13/0x20
> [<c117c93c>] ? kref_get+0x1c/0x20
> [<c117bb2f>] ? kobject_get+0xf/0x20
> [<c124d630>] ? get_device+0x10/0x20
> [<c124e5a0>] ? device_add+0x60/0x530
> [<c117b8b5>] ? kobject_init+0x25/0xa0
> [<c12569f9>] ? _request_firmware+0x139/0x3e0
> [<c1256cc0>] ? request_firmware_work_func+0x20/0x70
> [<c1256ca0>] ? request_firmware_work_func+0x0/0x70
> [<c103ff24>] ? kthread+0x74/0x80
> [<c103feb0>] ? kthread+0x0/0x80
> [<c1003136>] ? kernel_thread_helper+0x6/0x10
>---[ end trace 2d50bd818f64a1b7 ]---
- followed by a random Oops -
Avoid that by waiting for the firmware loading to finish
(whether successfully or not) before the unbind in
ar9170_usb_disconnect.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Bug-fixed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down. Device failure/removal
etc are still recorded on spares.
However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:
This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain,
how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.
So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately. There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update). We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.
Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
It's unused and buggy in its current form, since it can place a bo
in the reserved state without removing it from lru lists.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds